Search

Packaging insulation materials with high thermal conductivity and excellent dielectric properties are favorable to meet the high demand and rapid development of third generation power semiconductors. In this study, we propose to improve the thermal conductivity of epoxy resin (EP) by incorporating a three-dimensional boron nitride thermally conductive network. Detailedly, polyurethane foam (PU) was used as a supporter, and boron nitride nanosheets (BNNSs) were loaded onto the PU supporter through chemical bonding (BNNS@PU). After immersing BNNS@PU into the EP resin, EP-based thermally conductive composites were prepared by vacuum-assisted impregnation. Fourier transform infrared spectrometer and scanning electron microscope were used to characterize the chemical bonding and morphological structure of BNNS@PU, respectively. The content of BNNS in BNNS@PU/EP composites was quantitatively analyzed by TGA. The results show that the thermal conductivity of the BNNS@PU/EP composites reaches 0.521 W/m K with an enhancement rate η of 30.89 at an ultra-low BNNS filler content (5.93 wt. %). Additionally, the BNNS@PU/EP composites have excellent dielectric properties with the frequency range from 101 to 106 Hz. This paper provides an interesting idea for developing high thermal conductivity insulating materials used for power semiconductor packaging. [ABSTRACT FROM AUTHOR]

Over the last two decades, Electron Energy Loss Spectroscopy (EELS) imaging with a scanning transmission electron microscope has emerged as a technique of choice for visualizing complex chemical, electronic, plasmonic, and phononic phenomena in complex materials and structures. The availability of the EELS data necessitates the development of methods to analyze multidimensional data sets with complex spatial and energy structures. Traditionally, the analysis of these data sets has been based on analysis of individual spectra, one at a time, whereas the spatial structure and correlations between individual spatial pixels containing the relevant information of the physics of underpinning processes have generally been ignored and analyzed only via the visualization as 2D maps. Here, we develop a machine learning-based approach and workflows for the analysis of spatial structures in 3D EELS data sets using a combination of dimensionality reduction and multichannel rotationally invariant variational autoencoders. This approach is illustrated for the analysis of both the plasmonic phenomena in a system of nanowires and in the core excitations in functional oxides using low loss and core-loss EELS, respectively. The code developed in this manuscript is open sourced and freely available and provided as a Jupyter notebook for the interested reader. [ABSTRACT FROM AUTHOR]

Low-energy ion beam irradiation, combined with the introduction of impurities, presents a promising approach for nanopatterning silicon (Si) surfaces. In this research, we investigate the surface evolution of Si (100) surfaces irradiated by 75 eV helium (He) plasma, in the presence of tantalum (Ta), traditionally regarded as an impurity incapable of initiating pattern formation, as evidenced in prior studies. The Ta impurities are pre-deposited onto the Si surfaces using the magnetron sputtering method, which offers a more controlled and quantifiable approach compared with the conventional co-deposition route. After irradiation at 800 K, dense cone arrays are produced on the Si surface. The growth of the cones is explored for fluence spanning (1–10) × 1025 m−2. The cross-sectional scanning electron microscope images indicate that the cone lengths and base width are well characterized by t1/2 dependence. The kinetics of the cone growth follow Fick's law, characterized by an effective diffusive mechanism with the coefficients of diffusion: D = 6.49 ± 0.83 × 10−16 m−2 s−1. Transmission electron microscope observations reveal that the cone has distinct inner and outer parts with different microstructures and a clear interface. The growth mechanism of these cones is elucidated as a composite process involving preferential sputtering, the destabilizing influence of He bubbles, and the migration of adatoms. [ABSTRACT FROM AUTHOR]

The scanning electron microscope (SEM) recordings of dynamic nano-electromechanical systems (NEMS) are difficult to analyze due to the noise caused by low frame rate, insufficient resolution, and blurriness induced by applied electric potentials. Here, we develop an image processing platform enhanced by the physics of the underlying system to track the motion of buckling NEMS structures in the presence of high noise levels. The algorithm is composed of an image filter, two data filters, and a nonlinear regression model, which utilizes the expected form of the physical solution. The method was applied to the recordings of a NEMS beam about 150 nm wide, undergoing intra- and inter-well post-buckling states with a transition rate of approximately 0.5 Hz. The algorithm can track the dynamical motion of the NEMS and capture the dependency of deflection amplitude on the compressive force on the beam. With the help of the proposed algorithm, the transition from inter-well to intra-well motion is clearly resolved for buckling NEMS imaged under SEM. [ABSTRACT FROM AUTHOR]

A non-destructive method for detecting sub-micrometer-sized micropipes on an entire wafer surface is investigated. Since it is difficult to detect sub-micrometer-sized micropipes due to their small core size, a non-destructively and accurately detecting method is required. To solve the issue, we focus on a characteristic depression generated around micropipes, namely, line-shaped depressions. In this paper, the location of line-shaped depressions is identified by using optical inspection, and the line-shaped depressions are distinguished whether micropipes exhibit line-shaped depression or not by using mirror electron microscope observation as high-resolution inspection. The accuracy of the distinction results is confirmed by scanning electron microscope observation, and electrical characteristics of the P–N diode are fabricated using the inspected wafer. Furthermore, the sub-micrometer-sized micropipes are observed at the sites of leakage current identified by emission microscopy. Additionally, device simulation of the blocking-voltage characteristics of P–N diodes suggests that the increase in leakage current depends on the electric field at the sub-micrometer-sized micropipes, regardless of their core size. [ABSTRACT FROM AUTHOR]

Gastropods forage with their radula, a thin chitinous membrane with embedded teeth, which scratch across the substrate to lose food particles. During this interaction, the risk of loosening particles is obvious without having a specialized mechanism holding them on the tooth surface. As mucus secretions are essential in molluscan life cycles and the locomotion and attachment gels are known to have an instant high adhesion, we have hypothesized that the saliva could support particle retention during feeding. As adhesion of snail saliva was not studied before, we present here an experimental setup to test its particle-binding capacity using a large land snail (Lissachatina fulica, Stylommatophora, Heterobranchia). This experiment was also applied to the gels produced by the snail foot for comparison and can be potentially applied to various fluids present at a small volume in the future. We found, that the saliva has high particle retention capacity that is comparable to the foot glue of the snail. To gain some insight into the properties of the saliva, we additionally studied it in the scanning electron microscope, estimated its viscosity in a de-wetting experiment, and investigated its elemental composition using energy dispersive X-ray spectroscopy reveling higher contents of Ca, Zn and other potential cross-linkers similar to those found in the glue. [ABSTRACT FROM AUTHOR]

In recent years, precision and accuracy for a more precise critical dimension (CD) control have been required in CD measurement technology. CD distortion between the measurement by a critical dimension scanning electron microscope (CD-SEM) and a reference tool is the most important factor for a more accurate CD measurement. CD bias varies by a CD-SEM and a pattern condition. Therefore, it is urgently needed to identify, characterize, and quantify those parameters that may or may not affect the CD measurement by a CD-SEM. The sensitivity of the Monte Carlo simulated CD-SEM images with multiple physical modeling components has been studied previously. In this study, we demonstrate that the work function and elastic scattering potential models have a significant impact on secondary electron emission intensity, but their influence on the shape of the linescan profile is small, and other factors like the optical energy loss function and dielectric function models have even smaller effects. We have evaluated the uncertainty in the linescan profiles of Si line structures with different sidewall angles due to several different physical factors. It is found that when the CD is evaluated by a peak/valley method, the uncertainty of the CD is negligible. Therefore, it is concluded that the CD value and its related uncertainty are not critically related to the physical factors of the present Monte Carlo simulation model but rely dominantly on the line structure and electron beam parameters. [ABSTRACT FROM AUTHOR]

We report on the metrological characterization of the emission from a germanium-vacancy center in diamond under a microfabricated solid immersion lens in a confocal laser-scanning microscope setup. Ge ions were implanted into a synthetic diamond at 3 MeV, and germanium-vacancy centers were then formed by subsequent annealing. Afterward, solid immersion lenses were fabricated in a focused ion beam scanning electron microscope. The photoluminescence was investigated at room temperature in terms of the spectral distribution, the excited state lifetime, the second-order correlation function, and the saturation behavior, proving simultaneous high single-photon purity and high brightness. Two methods were exploited to minimize the residual multi-photon probability: spectral filtering and temporal filtering. According to these results, we assume that Raman scattered photons and emission from neighboring color centers play an important role in the residual multi-photon emission probability. The system efficiency of the single-photon source was investigated and found to be in accordance with the value calculated from all sources of loss in the setup. The branching ratio of the germanium-vacancy center for the decay into the ground state and into metastable state was calculated. The results enable the usage of the single-photon source in future quantum radiometric experiments. [ABSTRACT FROM AUTHOR]

Because of their full compatibility with CMOS technology, HfO2-based ferroelectrics, and especially Hf0.5Zr0.5O2 (HZO), attract a lot of attention. However, the overwhelming majority of measurement techniques provides only information about the cumulative electrical response of many domains of HZO, i.e., at the macroscopic level. So far, only piezoresponse force microscopy technique was applied to visualize distinct ferroelectric domains in HZO and to analyze the local switching behavior in the microscopic level. This work introduces the possibility of using electron beam-induced current (EBIC) technique in the scanning electron microscope to visualize the gradual polarization reversal of HZO and to obtain the local polarization dynamics. We show that although the local EBIC signal is affected by surrounding domains, studying the variations in the ferroelectric response of individual domains as well as the spread of the local stiffness and local imprint is possible by this method. Besides, we show the connection between the EBIC current and an electric field across passive non-ferroelectric layers at interfaces between HZO and metal electrodes, which opens up additional opportunities to use the EBIC technique for investigations of interface-dependent properties of HZO ferroelectrics in the future. [ABSTRACT FROM AUTHOR]

Because of their full compatibility with CMOS technology, HfO2-based ferroelectrics, and especially Hf0.5Zr0.5O2 (HZO), attract a lot of attention. However, the overwhelming majority of measurement techniques provides only information about the cumulative electrical response of many domains of HZO, i.e., at the macroscopic level. So far, only piezoresponse force microscopy technique was applied to visualize distinct ferroelectric domains in HZO and to analyze the local switching behavior in the microscopic level. This work introduces the possibility of using electron beam-induced current (EBIC) technique in the scanning electron microscope to visualize the gradual polarization reversal of HZO and to obtain the local polarization dynamics. We show that although the local EBIC signal is affected by surrounding domains, studying the variations in the ferroelectric response of individual domains as well as the spread of the local stiffness and local imprint is possible by this method. Besides, we show the connection between the EBIC current and an electric field across passive non-ferroelectric layers at interfaces between HZO and metal electrodes, which opens up additional opportunities to use the EBIC technique for investigations of interface-dependent properties of HZO ferroelectrics in the future. [ABSTRACT FROM AUTHOR]

Measurements of transport phenomena are constantly plagued by contact resistance, prohibiting the sample's intrinsic electrical or thermal conductivity from being accurately determined. This predicament is particularly severe in thermal transport measurements due to the inability to meet similar impedance requirements for a four-probe method used in electrical resistance measurements. Here, we invent a three-probe measurement method that makes an accurate determination of thermal conductivity possible for nanomaterials. Incorporating electron beam heating provided by a scanning electron microscope (SEM) on a diffusive thermal conductor not only quantifies the thermal contact resistance, which may introduce an error of more than 270% to a sample's thermal conductivity, but also eliminates several device uncertainties that may contribute an additional 17% error in a measurement. The method also enables local temperature measurements, revealing nanoscale structural variations unfound by SEM. The high accuracy of the technique would make standardization of nanoscale thermal transport measurement possible. [ABSTRACT FROM AUTHOR]

Lead-free antiferroelectric AgNbO3 ceramics have garnered extensive attention due to their rapid charge/discharge capabilities and environmentally friendly nature, holding immense potential for energy storage applications. However, the practical utilization of AgNbO3 has been hindered by its low energy storage density. This study employed an A/B-site co-doping strategy, which yielded positive effects on the energy performance of AgNbO3 ceramics. By modifying the A/B-sites with equivalent amounts of Bi3+ and Y3+ ions, enhanced maximum polarization, improved breakdown field, and slimmer hysteresis loops were simultaneously achieved, as the combined effects of refined grain size, wider optical bandgap, and randomly distributed antiferroelectric nanodomains, which were verified through the scanning electron microscope, transmission electron microscope, and ultraviolet–visible spectrum. As a consequence, a high energy storage density of 5.40 J/cm3 accompanied by an energy storage efficiency of 56.5% was achieved in the Ag0.97Bi0.01Nb0.994Y0.01O3 ceramic under a relatively low electric field of 190 kV/cm. This study underscores the effectiveness of A/B-site aliovalent co-doping as a viable strategy for developing high-performance ceramic capacitors for energy storage applications. [ABSTRACT FROM AUTHOR]

We reported here on the fabrication and characterization of a smart titanium alloy bolt based on a high-frequency piezoelectric thin-film sensor. The thin-film sensor was directly deposited on a titanium alloy bolt head with radio frequency magnetron sputtering and characterized by a scanning electron microscope and an atomic force microscope. The ultrasonic characteristics of the smart bolt, which include a pure and broad frequency spectrum peaked at 14.81 MHz, high measurement accuracy below 3%, and high repeatability free from some interference from bolt detection position change, were fully characterized. No obvious frequency shift was observed with the increase in axial preload. Based on the mono-wave method [TOF (time of flight) of longitudinal mode wave], TOF change increased linearly with preload force in the range of 0–20 kN. With the increase in temperature from 22 to 150 °C, the TOF linearly increases while the longitudinal wave velocity linearly decreases. The results indicate the prepared smart titanium alloy bolt is suitable as a smart aviation and automotive fastener. [ABSTRACT FROM AUTHOR]

Integrating carbon nanotubes (CNTs) into a polymer matrix can significantly modify its physical properties, providing that the challenges associated with CNT dispersion are successfully resolved. In this work, we investigate the enhancement of the dielectric properties of silicone when multiwall carbon nanotubes (MWCNTs) are introduced to its polymer matrix as a filler in the frequency range from 0.5 to 20 GHz. An optimized procedure is used to prepare nanocomposites with MWCNTs concentrations by weight of 0%, 0.5%, 1.0%, 1.5%, and 2.0%. The investigated dielectric properties for the prepared nanocomposites are the real dielectric constant ɛ′, the imaginary dielectric constant ɛ″, the loss tangent tan δ, and the AC conductivity σAC. The dispersion of the MWCNTs in the silicone matrix is confirmed using the Fourier-transform infrared (FTIR) spectroscopy and the scanning electron microscope. This study shows that the dielectric properties of the nanocomposite are enhanced as the MWCNT's concentration is increased over the entire frequency range. For example, the enhancement in ɛ′ value was from 3.2 up to 21.6 at 0.5 GHz and from 2.5 to 10.6 at 20 GHz as the concentration increased from 0% to 2.0%. For the ɛ″ value, the enhancement was from less than 0.1 to 8.6 at 0.5 GHz and to 2.0 at 20 GHz, respectively. Based on the obtained tanδ values, the nanocomposites with MWCNTs of 0.5% and 1.0% can be classified as low-loss dielectrics, while the other nanocomposites with MWCNTs of 1.5% and 2.0% are classified as lossy dielectrics. [ABSTRACT FROM AUTHOR]

The damage impact of mechanical shocks on stator bar insulation is a key factor in high-voltage motor accidents. This study conducted electrical aging acceleration and breakdown experiments on damaged stator insulating materials to understand failure causes and evaluation methods. The relationship between sample defect area and depth and electrical properties was analyzed, along with the morphology of the damaged surface using a scanning electron microscope. Results show that the defect area correlates with impact mode but does not directly impact electrical performance. Effective insulation thickness is positively linked to electrical performance. This study serves as a valuable reference for evaluating mechanical impact faults in high-voltage motors. [ABSTRACT FROM AUTHOR]

By applying ultrasonic treatment to ZL205A aluminum alloy melt containing different Cd contents and then using a tensile test, a scanning electron microscope experiment, and a metallographic experiment, the influence of ultrasonic treatment to ZL205A aluminum alloy melt on the properties of aluminum–copper alloy with different Cd contents in the liquid phase high-temperature region was studied. The effect of ultrasonic treatment on the solidification structure of ZL205A aluminum alloy was investigated. The results showed that there was no significant difference in the form of Cd and the solid solution rate of the aluminum alloy with different Cd contents in ultrasonic-assisted casting. However, the effect of ultrasonic waves on the high-temperature liquid phase of the melt of ZL205A aluminum alloy can effectively reduce the porosity defects in the solidification structure of the casting, refine the solidification structure, and make the structure more uniform. The ultrasonic cavitation effect can promote the formation and uniform distribution of Al–3Ti and improve the nucleation rate, and the effect can continue after heat treatment. This can solve the problem that increasing Cd content in ZL205A greatly reduces the toughness of castings while increasing the strength. The sample with a Cd content of 0.20% and with ultrasonic treatment has the highest strength, the average tensile strength is 475.5 MPa, and the yield strength is 381.75 MPa. However, compared with the conventional casting samples with the same Cd content, the decrease in elongation was significantly reduced. [ABSTRACT FROM AUTHOR]

The changes in mechanical properties of glass fiber reinforced plastic cross-ply laminates as a result of hydrothermal aging were studied theoretically. The composite specimens have been immersed in distilled water at 25, 40, and 70 °C for 60 days for aging testing. Based on Fick's law and the Arrhenius theorem, the moisture absorption data under different environments was analyzed, and the method for determining the diffusivity and the equilibrium moisture content was obtained. The relationship model between the moisture absorption behavior of the composite material and the ambient temperature was proposed and verified by finite element analysis. The mechanical behavior of the composites was studied by tensile, compression, and three-point bending tests. Under the condition of ultimate moisture absorption, the tensile, compressive, and bending strengths of the composite decreased by 31.663%, 12.948%, and 26.985%, respectively. A variety of empirical models were used for data analysis, which confirmed the strong correlation between strength degradation and moisture absorption of composite cross-ply laminates. The scanning electron microscope observation results of different moisture absorption levels showed that matrix cracking and fiber/matrix interface debonding caused by moisture absorption are the fundamental reasons for the strength degradation of the composites. [ABSTRACT FROM AUTHOR]

With this experimental study, ZrO2/B4C/Al2O3/SiC ceramics in different weight ratios were added to 99.5% pure aluminum and composites were produced by vacuum infiltration, which is very rare in the literature. It is aimed to investigate how different ceramics will affect the technical properties of an aluminum composite. First, scanning electron microscope images were taken to examine their microstructures, and energy-dispersive x-ray spectroscopy analyses were performed. In addition, x-ray diffraction analyses of phase structures were performed. Then, the densities of the composite structures were measured. In the last stage of the experiments, hardness measurement, bending strength, and abrasive wear amount tests were carried out to determine the mechanical properties of the composite structures. According to the data obtained, a relatively homogeneous structure was obtained up to 10% of the ceramic particles in the structure. It was observed that thermal damage did not occur in the composite structures and no significant phase changes occurred. The highest infiltration distance was obtained from B4C-reinforced samples, and the lowest infiltration distances were obtained from ZrO2-reinforced samples. Ceramic reinforcement elements have reduced the density values of composite structures. With the increase in the ratio of ceramic reinforcement particles, the hardness values of the composites increased and the flexural strength values decreased. In the abrasive wear tests, the least wear loss was obtained from SiC-reinforced samples and the highest wear loss was obtained from ZrO2-reinforced samples. When the composites were evaluated according to their microstructure and mechanical strength, the best results were obtained with SiC and then Al2O3, B4C, and ZrO2 reinforcements, respectively. It has been concluded that SiC, Al2O3, B4C, and ZrO2 reinforcement elements in Al 1050-based composites produced by vacuum infiltration have a positive effect on most of the mechanical properties and a negative effect on some of them. [ABSTRACT FROM AUTHOR]

Near-stoichiometric chromium diboride films were subject to in situ annealing inside a scanning transmission electron microscope to access the thermal behavior of the film and embedded structural planar defects. Independent of films' stoichiometry, the planar defects were unaffected by the applied heat treatments. On the contrary, the interfaces between the boron-rich tissue phase and the CrB2 phase were reshaped in the overstoichometric CrB2 film. At high temperatures, diffusion of contact metal species (platinum) from the focused ion beam sample preparation was triggered, with subsequent migration onto the sample. This resulted in the formation of metal-rich regions as directly observed and characterized at the atomic level. We determined that platinum did not react with the diboride structure but is accommodated by various defects present in the film. [ABSTRACT FROM AUTHOR]

Focussed ion beam - scanning electron microscope (FIB-SEM) 3D examination was conducted on three standard UO2 and one Cr doped UO2 high burn-up pressurized water reactor (PWR) fuel samples. This work complemented other microanalysis examination, including an electron backscattered diffraction (EBSD) work on the polished surface. A parallel article giving the EBSD results was submitted simultaneously. Together, they found, in all the central area of these high burn-up samples: (i) a restructuring of the initial grains into smaller sub-grains forming low angle boundaries and with crystal orientations around that of their parent grains; and (ii) intragranular bubbles mostly situated on these low angle boundaries. The FIB-SEM 3D examination showed how such inter-sub-grain bubbles start as small compact but also small lenticular bubbles, similar to typical small intergranular lenticular bubbles. With increasing burn-up, these lenticular bubbles get thicker and locally interlink to form more complex bubbles. However, no long distance networks, between the sub-grains or between the original grains, were found. Such networks could have been a path for part of the fission gases to reach the grain boundaries, the grain edges (the intersection line of three grain boundaries), and the rod free volumes. These FIB-SEM 3D examinations brought details on the intragranular and intergranular bubbles situation for each studied volume. The distribution of the intragranular bubbles according to their sizes and shapes was exposed. The central restructuring, studied in this work, is likely to play a role in the increase of the fission gas release fractions at high burn-up. This work is an incentive to study further this restructuring and the bubbles formed, combining different approaches. [ABSTRACT FROM AUTHOR]

Materials research studies are dealing with a large number of images, which can now be facilitated via image-based machine learning techniques. In this article, we review recent progress of machine learning-driven image recognition and analysis for the materials and chemical domains. First, the image-based machine learning that facilitates the property prediction of chemicals or materials is discussed. Second, the analysis of nanoscale images including those from a scanning electron microscope and a transmission electron microscope is discussed, which is followed by the discussion about the identification of molecular structures via image recognition. Subsequently, the image-based machine learning works to identify and classify various practical materials such as metal, ceramics, and polymers are provided, and the image recognition for a range of real-scenario device applications such as solar cells is provided in detail. Finally, suggestions and future outlook for image-based machine learning for classification and prediction tasks in the materials and chemical science are presented. This article highlights the importance of the integration of the image-based machine learning method into materials and chemical science and calls for a large-scale deployment of image-based machine learning methods for prediction and classification of images in materials and chemical science. [ABSTRACT FROM AUTHOR]

In this study, basalt fibers (BFs) and nano-silica (NS) were innovatively combined to reinforce recycled aggregate concrete (RAC) to prepare recycled aggregate concrete (named NBRAC) with better mechanical and microstructural properties as an alternative to ordinary concrete. Different NBRAC specimens were prepared by adjusting the contents of NS and BF; the damage mechanism and mechanical properties of NBRAC were investigated; and the compressive, split tensile, and flexural strengths of NBRAC were evaluated. The microstructure of NBRAC was analyzed by scanning electron microscopy observation. The results showed that the densification of NBRAC was improved under the condition of 50% RA substitution rate and that its compressive, split tensile, and flexural strengths were increased by 6.8%, 16.3%, and 32.7%, respectively, compared with that of natural concrete, which proved that the method was feasible for the preparation of high-performance RAC. Scanning electron microscope image analysis confirmed the improvement effects of NS and BF on RAC, and combined with the experimental data, a composite explanation for the improvement effects of NS and BF on RAC was proposed for the first time. [ABSTRACT FROM AUTHOR]

The use of slag-based alkali-activated concrete (AAC) could effectively address the issues of resource extraction and carbon emissions caused by traditional Portland cement. In this study, the effects of the fly ash content, water–binder ratio, and alkali activation modulus on the early mechanical properties of AAC were investigated. A total of 105 cube specimens (35 sets) were designed and subjected to compressive strength tests, scanning electron microscope tests, and x-ray diffraction composition analysis. The results indicated that excellent early strength was observed in AAC, with a compressive strength reaching ∼90% of the 28th day strength before 14 days. An increase in the fly ash content and a decrease in the water–binder ratio significantly improved the compressive strength within the same age period. The impact of a lower alkaline activation modulus on strength was found to be insignificant. Based on the experimental results, a calculation method and a constitutive model for early strength were proposed, and the theoretical values exhibited a high level of agreement with the measured values. [ABSTRACT FROM AUTHOR]

This paper presents a novel piezoelectric-driven nanoindentation system for a scanning electron microscope (SEM) with an improved analog compensation (IAC) method. This system mainly consists of a piezoelectric-driven indenter head, a rectangle-shaped transducer, and a nanopositioner module. Compared with the state-of-the-art piezoelectric-driven nanoindentation system with a circle-shaped transducer, the proposed nanoindentation system is capable of multi-direction operation inside a SEM with a rectangle-shaped transducer. Self-matched semiconductor strain gauges are selected as the position sensor for the piezoelectric-actuator. The Wheatstone bridge output voltage cannot achieve a zero temperature coefficient because the temperature coefficients of self-matched semiconductor strain gauge pairs become significantly different from each other after installation in practice. An IAC method is proposed to compensate the temperature coefficients further. Compared with the existing analog compensation method, the IAC method solves the problem of amplifier saturation and improves the sensitivity of the self-matched semiconductor strain gauge pairs position sensor by 27%. The multi-direction operation results inside a standard SEM HITACHI SU5000 validate the advantage of the developed nanoindentation system. [ABSTRACT FROM AUTHOR]

The present study focused on the environmentally friendly preparation, characterization, and certain biological activities of gold nanoparticles (Au-NPs) made with the Gundelia tournefortii (kenger) leaf extract. The results from devices such as transmission electron microscope, energy-dispersive x-ray spectrophotometer, and Fourier scanning electron microscope reveal the structures of nanoparticles. After an hour, the greatest surface plasmon resonance was discovered at 532.15 nm. The mean cubic crystallite size was calculated using the powder x-ray diffraction model and was found to be 23.53 nm. It was noted that the produced Au-NPs had spherical forms and hexagonal dimensions and ranged in size from 5 to 40 nm. The minimum inhibitory concentration and a colorimetric method for determining cell metabolic activity test, respectively, were used to investigate the suppressive effects of Au-NPs on the growth of pathogenic bacteria and healthy and cancer cell lines. [ABSTRACT FROM AUTHOR]

The fluid transport in porous media is a critical property for oil and gas exploitation, construction engineering, and environmental protection. It is profoundly influenced by pore geometry and mineral properties. Currently, the Kozeny–Carman equation serves as the permeability prediction equation for porous media, established on the circular pores model. However, it fails to fully account for the impact of pore shape and mineral properties of the soil, leading to significant deviations between predicted and measured soil permeability results. In this paper, based on scanning electron microscope image and mercury intrusion porosimetry, the pores were divided into circular pores and narrow slit pores according to the ratios of pore area and circumference. Then, the quantitative expression of the two types of pores and their connectivity and tortuosity were given, and the circular and narrow slit composite pore model was used to describe the soil pore. Subsequently, the electrostatic potential of pore water was calculated by the Poisson–Boltzmann equation to consider the adsorption effect of minerals on pore water. Combined with the Navier–Stokes equation, the permeability prediction equation considering pore geometry, pore connectivity, and tortuosity and mineral properties was established. Finally, the experimental results illustrated that the theoretical prediction results were in good agreement with the experimental results. The proposed permeability prediction equation proves valuable for assessing and predicting the fluid transport in porous media. [ABSTRACT FROM AUTHOR]

The operando hydrogen microscope is an original apparatus that has been developed to visualize the time-dependent permeation of hydrogen through a sample. This apparatus is developed based on an ultrahigh vacuum scanning electron microscope (UHV SEM). The system consists of a lens system to focus ions produced by electron-stimulated desorption (ESD), an ion detector optimized for ESD-signal detection, and a two-dimensional measurement program synchronized with the position information of the electron beam. The developed detectors and electrostatic lenses enable highly sensitive detection of the ions. In this paper, we show the details of the instrumentation of the operando hydrogen microscope. We have succeeded in recording hydrogen and deuterium flowing from the rear of metals to the surface as a series of time-lapse images, showing the time-dependent changes in the surface distribution of hydrogen and deuterium. Deuterium permeation through the metal sample was dynamically visualized at the surface by the two-dimensional mapping of the desorbed ions induced by scanning electron beam irradiation. [ABSTRACT FROM AUTHOR]

Using a scanning electron microscope, we irradiate graphene drums with electrons at an energy of 20 keV and a dosage of about 1.58 × 1017 electrons/cm2. The drums consist of graphene exfoliated in ambient air over holes having a diameter of 4.6 μm and etched into an SiO2 substrate. After irradiation, we observe that the drum's suspended monolayer (ML) region has a ratio of the Raman D peak height, ID, to the Raman G peak height, IG, as high as 6.3. In contrast, the supported ML on the SiO2 substrate has an ID/IG ratio of 0.49. Previous studies have shown that graphene drums containing air can leak in a vacuum at a low rate. We attribute the high ID/IG ratio of the suspended ML to the air that may be in the drums. We propose that the air produces much adsorbed water on the ML, resulting in a high average defect density during irradiation. We present Raman maps of the full-width-at-half maximum, position, and height of the G, 2D, D, and D' peaks before and after irradiation and maps of ID/IG and ID/ID'. We anneal the drums at temperatures from 50 to 215 °C and find that ID/IG significantly reduces to 0.42. The annealing data are analyzed using an Arrhenius plot. We also find that ID/ID' depends on annealing temperature and has values ≥8, in the range expected for sp3 defects, for ID/IG ≤ 3.9. This irradiation method may help achieve high average defect densities in ML graphene, imparting novel and potentially valuable properties. [ABSTRACT FROM AUTHOR]

Laminar-type spherical diffraction gratings overcoated with carbon-based materials were designed, fabricated, and evaluated for the purpose of enhancing the analytical sensitivity of the flat-field spectrograph in a vacuum ultraviolet region of 35–110 eV. As the design benchmark for numerical calculations, diffraction efficiency (DE) and spectral flux, which are defined by the product of the DE and numerical aperture and correlate with the analytical sensitivity of the spectrograph, were used. To simplify the feasibility study on the overcoating effects, we assumed a laminar-type grating having a grating constant of 1/1000 mm and coated with a Au layer of 30.0 nm thickness and an incidence angle of 84.0°. The optimized groove depth and duty ratio were 30.0 nm and 0.3, respectively. In addition, the optimum thicknesses of the overcoating layer were 44, 46, 24, and 30 nm for B4C, C, diamond-like-carbon, and SiC, respectively. Based on these results, we have fabricated a varied-line-spacing holographic grating overcoated with B4C with a thickness of 47 nm. For the experimental evaluation, we used the light source of Mg-L and Al-L emissions excited by the electron beam generated from an electron microscope, an objective flat-field spectrograph, and a CCD imaging detector. The experimental results showed that the spectrograph employing a new grating overcoated with the B4C layer indicated almost the same spectral resolution and 2.9–4.2 times higher analytical sensitivity compared with those obtained with a previously designed Au-coated grating having a grating constant of 1/1200 mm and used at an incidence of 86.0°. [ABSTRACT FROM AUTHOR]

Lithium batteries are promising techniques for renewable energy storage attributing to their excellent cycle performance, relatively low cost, and guaranteed safety performance. The performance of the LiFePO4 (LFP) battery directly determines the stability and safety of energy storage power station operation, and the properties of the internal electrode materials are the core and key to determine the quality of the battery. In this work, two kinds of commercial LFP batteries were studied by analyzing the electrical properties and material properties of the electrodes. After performing the rate and cycle performance tests of the battery cell, differential scanning calorimetry, scanning electron microscope, x-ray diffraction, and inductively coupled plasma were used to explore the performance of electrode materials to establish the correlation between the battery performance and the electrochemical reaction law of the internal materials and further to judge the influence of the key material properties on the battery performance. This work opens up an avenue for technical supervision of energy storage power stations. [ABSTRACT FROM AUTHOR]

To address the challenges of accurate metrology of height and sidewall angle (SWA) of three-dimensional structures with critical dimension scanning electron microscopy, general modeling and algorithms based on tilted electron beam technology and the corresponding application skills are proposed, and the validity and error accuracy are evaluated as well. Three typical structures, the trapezoid, inverted trapezoid, and step, are investigated with Monte Carlo simulation. The maximum derivative method is used to extract key parameters from the secondary electron linescan. The efficiency of the proposed modeling, algorithms, and the accuracy of the calculated height and SWA are improved further with the application of wavelet transform. [ABSTRACT FROM AUTHOR]

Lateral field emission devices have been characterized before and after ultraviolet (UV) light exposure. Two types of planar device structures, diode and bowtie, were studied. These nanoscale devices have 9–15 nm tip-to-tip (bowtie) or tip-to-collector (diode) dimensions with the tips fabricated from Au/Ti. Typical currents of 2–5 nA per tip at 6 V were measured. It was observed that after UV exposure, the collected current was reduced by >28% for the case of a bowtie device; whereas the current was reduced by >39% for the case of a diode device. This reduction can be attributed to water vapor desorption on the dielectric surface between the structures, which in turn reduces surface leakage. The Fowler–Nordheim plot showed a straighter line after UV exposure. After the I-V test, the UV-exposed devices were placed on lifetime tests in a vacuum of <10−8 Torr and were biased at 5 V DC. After 2600 h, an abrupt current decrease was observed: ∼25% for the case of the bowtie and ∼28% for the case of the diode device. Scanning electron microscope images of the bowtie and diode devices showed damage to the tips. [ABSTRACT FROM AUTHOR]

This paper describes the influence of vacuum annealing on the mechanical characteristics of silicon (Si) nanowires (NWs) fabricated using focused ion beam (FIB) technologies. Two types of Si NWs having a cross-sectional one-side length or diameter ranging from 19 to 447 nm are prepared using the direct milling and Ga ion doping functions of FIB. The Si NWs prepared are annealed at 400–700 °C in high vacuum for 10 min, followed by quasi-static uniaxial tensile testing using a microelectromechanical system based tensile test system in a scanning electron microscope. All the Si NWs fracture in a brittle manner. Young's modulus of submicrometer-sized Si NWs shows both annealing and specimen size influences in the range from 120 to 170 GPa, whereas that of nano-sized Si NWs shows only annealing influence in the range from 60 to 110 GPa. Tensile strength scatters greatly, ranging from 1.0 to 7.2 GPa, which increases with increasing the NW size. A transmission electron microscope and an atomic force microscope suggest that, by annealing, recrystallization happens in the damaged layer introduced by FIB milling and the NW surface morphology changes due to its recrystallization and gallium (Ga) ion evaporation. Fracture origin is discussed through the comparison between surface roughness and crack length estimated by the Griffith theory of brittle fracture. [ABSTRACT FROM AUTHOR]

Dust-mitigating surfaces typically consist of high-aspect-ratio structures that separate particles from resting on the bulk material, thereby limiting adhesion due to short-range van der Waals forces. These surfaces can find uses in solar-panel coatings and a variety of dust-resistant optics. The current method for quantifying surface contamination is optical microscopy, but this method is inadequate for observing particles at the submicrometer scale due to the diffraction limit. Furthermore, regardless of the microscopy technique, particle identification becomes problematic as the particle contaminates approach the same length scale of the surface structures. In this work, we demonstrate a method to identify micro-/nanoparticle contaminates on nanostructured surfaces using electron microscopy and image processing. This approach allows the characterization of particles that approach the length scale of the surface structures. Image processing, including spectrum filters and edge detection, is used to remove the periodic features of the surface nanostructure to omit them from the particle counting. The detection of these small particles using electron microscopy leads to an average of 5.62 particles/100 μm2 detected compared to 0.63 particles/100 μm2 detected for the traditional confocal optical detection method. Beyond dust-mitigation nanostructures, the demonstrated particle detection technique can find applications in nanobiology, the detection of ice nucleation on a structured surface, and semiconductor mask inspections. [ABSTRACT FROM AUTHOR]

Plasma etching effects, such as microtrenching and bowing, negatively impact device performance. Modeling of these effects at nanoscale is challenging, and theoretical and experimental investigations are highly desired to gain insights into mechanisms. In this paper, we propose a new plasma etching model based on Monte Carlo simulations with a cellular method. This model considers reactions and ion-enhanced etching and consists of a novel particle reflection algorithm, which is a key factor impacting the etch profile. This model reproduces the adjustable microtrenching and bowing effects in periodic dense trenches with tens of nanometer dimensions. We conduct experiments of Si etching by Cl 2 and validate the model by comparing the simulated profile with cross-sectional scanning electron microscope images. This work enables a potential physical model driven process emulation tool toward design technology co-optimization. [ABSTRACT FROM AUTHOR]

Through experimental observation and auxiliary numerical simulation, this investigation studies the different types of grain refinement of 5754 aluminum alloy laser beam welding by applying a transverse oscillating magnetic field. Scanning electron microscope results have proved that the application of a magnetic field can reduce the average crystal branch width and increase its number. The interaction between the induced eddy current generated by the Seebeck effect and the applied external magnetic field produces a Lorentz force, which is important for the increase in the number of crystal branches. Based on the theory of dendrite fragmentation and the magnetic field-induced branches increment, the grain size reduction caused by the magnetic field is studied. Furthermore, the effects of the magnetic field are analyzed by combining a phase field method model and simulations of nucleation and grain growth. The grain distribution and average grain size after welding verify the reliability of the model. In addition, the introduction of a magnetic field can increase the number of periodic three-dimensional solidification patterns. In the intersection of two periods of solidification patterns, the metal can be re-melted and then re-solidified, which prevents the grains, that have been solidified and formed previously, from further growth and generates some small cellular grains in the new fusion line. The magnetic field increases the building frequency of these solidification structures and thus promotes this kind of grain refinement. [ABSTRACT FROM AUTHOR]

In this study, we demonstrate an enhancement of the measured spin Seebeck coefficient in Fe3O4/Pt bilayer films due to an increase in Fe nanodroplets formed by pulsed laser deposition. Four bilayer films were deposited at the same time from a highly textured target, resulting in a general increase in droplet formation that was confirmed to be Fe rich by scanning electron microscope and transmission electron microscope-dispersive x-ray spectroscopy. Of these four films, there were two distinct groupings with differing density of α-Fe droplets, where the bilayer with higher droplet density exhibited a 64% increase in the measured spin Seebeck coefficient from 38 to 63 nV m/W. [ABSTRACT FROM AUTHOR]

The hole expansion ratio (HER) test is used to determine the stretch-flangeability of materials. Standard HER tests are performed on specimens sized a few tens of centimeters, termed macro-HER tests. This leads to significant material wastage due to the destructive nature of the tests. No information at the microstructure length scale is obtained, and the results suffer from user uncertainty in the identification of the through-thickness crack. This paper presents a novel miniature HER setup (termed micro-HER test), in which miniature specimens are tested inside a scanning electron microscope (SEM). The deformation is imaged from the top using the secondary electron detector installed in the SEM, coupled with the digital image correlation (DIC) technique, allowing for measurement of full field strains at the microstructural scale and identifying their deformation/fracture mechanisms. As a case study, six different steel grades were tested to measure their micro-HER values and compare them with the corresponding macro-HER values. The latter were found to be higher for the more ductile grades of steel. Late detection of through-thickness cracks and thicker samples leading to a higher volume of plastic deformation could contribute to this overestimation of values in macro-HER tests. DIC results from micro-HER tests on a ferrite–martensite (10% volume fraction) dual-phase steel showed high magnitudes of strain localization at the ferrite–martensite interfacial regions, indicating that such interfaces might be hotspots for failure under triaxial stress states. The challenges and errors associated with the measurements are also discussed. [ABSTRACT FROM AUTHOR]

To study the effect of aging on the low-temperature crack resistance of fiber asphalt mixes, three kinds of fibers (lignin fiber, polyester fiber, and basalt fiber) were dry blended into AC-13 asphalt mixes to prepare unaged, asphalt aged (that is, the original asphalt material is subjected to aging treatment), short-term aged, and long-term aged fiber reinforced asphalt mixes. Semicircular bending (SCB) tests and scanning electron microscopy tests were used to analyze and study the effects of aging time and fiber type on the low-temperature properties of asphalt mixtures at an ambient temperature of −5 °C. The SCB test results indicated that: with the deepening of aging, the fracture toughness and fracture energy of the fiber asphalt mixture specimens will tend to decrease, and the aging of the original asphalt has a greater impact on the specimens without fiber; there was great variability in the effect of lignin fibers on the crack resistance of the mix, but it could be a good promoter in unaged asphalt mixes; polyester fiber is the material of choice for improving low-temperature crack resistance in long-term aging pavements; the incorporation of basalt fiber greatly enhances the crack resistance of asphalt mixes and is an excellent material for improving aging asphalt mixes. It is clearly seen by the scanning electron microscope test that with the deepening of aging, the adhesion of asphalt and aggregate gradually deteriorates, and even more so, there is the phenomenon of fine aggregate flaking, and the fiber cannot play an excellent role in reinforcement and crack resistance. [ABSTRACT FROM AUTHOR]

Femtosecond laser ablation has found wide-ranging applications in the surface structuring of nanoelectronics and nanophotonics devices. Traditionally, the inspection of the fabricated three-dimensional (3D) morphology was performed using a scanning electron microscope or atomic force microscopy in an ex situ manner after processing was complete. To quickly monitor and efficiently optimize the quality of surface fabrication, we developed an in situ method to accurately reconstruct the 3D morphology of surface micro-structures. This method is based on a triangulation optical system that utilizes structured illumination. The approach offers a super-resolution capacity, making it a powerful and non-invasive tool for quick in situ monitoring of surface ablation structures. [ABSTRACT FROM AUTHOR]

Electric Field Assisted Sintering (EFAS, also referred to as spark plasma sintering) is a powerful technology for the consolidation of powder materials. The high heating rate during the sintering process is critical for minimizing energy consumption, but it can also cause microstructure heterogeneities in sintered parts, such as spatially varied porosity. The examination of localized porosity usually requires the use of a scanning electron microscope with a carefully prepared surface. In this paper, photothermal radiometry is used to measure local thermal diffusivity and extract localized porosity of EFAS-sintered parts by using a percolation-threshold model. Applying this approach, we identified the radial position-dependent porosity variation in EFAS parts, which is likely formed due to the large temperature gradient during the sintering process. This approach has a unique advantage because it can measure samples with minimal or no surface preparation, enabling the possibility of in situ characterization in EFAS with proper system modification. Necessary modifications on the measurement approach for EFAS deployment and in situ characterization are also discussed. [ABSTRACT FROM AUTHOR]

Scanning electron microscope is not only a versatile visualization and characterization tool for nanomaterials, but it is also widely used for visual feedback during assembly and manipulation of micro- and nanoparticles, novel devices based on 2D and 1D materials, and microrobots. Due to increase in the surface-to-volume ratio, adhesion forces play a significant role in micro- and nanorobotic applications. We investigate the quantitative effect of electron beam irradiation on nanoscale adhesive interactions between different end effector types and plain substrates. For this purpose, we use an interferometry-based force measurement setup integrated into the chamber of a scanning electron microscope capable of a subnano Newton force resolution. We provide quantitative results for the influence of the electron beam on the adhesion forces depending on the exposure dose, geometrical configuration in which it is applied, as well as on the material of the end effector. Simulation results, atomic force microscope adhesion measurements, and measurements with piezoresistive cantilevers serve as references. Our findings indicate that the electron beam influences the adhesive interaction not only in the case of insulating probes but also for well-grounded conducting and semiconducting probes. Its influence can range from several 10% to several 100% in comparison to the adhesion values measured with an atomic force microscope in an ambient atmosphere and no charged particle beam is applied. Moreover, it is shown that the influence of a charged particle beam is a multidimensional phenomenon that depends on several factors such as end effector and substrate material, geometry and aspect ratio of the end effector, geometrical configuration between particle beam and probe–sample arrangement, as well as exposure dose and field of view. We provide recommendations for handling and characterization of micro- and nano-objects using end effectors under the influence of charged particle beams: not to rely on adhesion values acquired in different environmental and exposure conditions, not to expect the application of conductive materials and grounding to completely avoid the effect of charged particle beams, and to be aware that charged particle beams can lower or increase the adhesion force in vacuum depending on material properties, among others. [ABSTRACT FROM AUTHOR]

Malignant central airway obstruction (MCAO) resulting from tumor metastasis and compression severely impairs respiration, posing life-threatening risks. To address this, we employed a synergistic modification strategy, combining cisplatin (CIS) and silver nanoparticles (AgNPs). Polycaprolactone (PCL) served as a drug carrier, enabling the preparation of a functional CIS@AgNPs@PCL fiber membrane-covered airway stent via electrospinning. This approach aimed to enhance the patency rate of MCAO. Characterization via ATR-FTIR, scanning electron microscope-energy-dispersive spectroscopy, and transmission electron microscope confirmed successful immobilization of CIS and AgNPs onto the stent surface. CIS@AgNPs@PCL substantially suppressed non-small cell lung cancer cells (A549), causing DNA damage, ultrastructural disruption, and over 50% apoptosis in 48 h. It also displayed potent antibacterial activity against Staphylococcus aureus, Pseudomonas aeruginosa, and Candida albicans biofilms. A mouse subcutaneous tumor recurrence model assessed anti-cancer efficacy. CIS@AgNPs@PCL fiber-covered stents significantly inhibited lung cancer tissue and enhanced anti-cancer effects by up-regulating caspase-3 and Bax, while down-regulating Bcl-2. This study's functional airway stent provides a proof-of-concept for an integrated anti-cancer and antibacterial strategy. It promptly restores the lumen, inhibits biofilm formation, prevents tumor progression, and improves postoperative MCAO patency. [ABSTRACT FROM AUTHOR]

The critical dimensions of advanced semiconductor manufacturing processes have decreased to a few tens of nanometers while the aspect ratios have increased beyond 100. The performance of plasma etch patterning processes as well as the cost and time of the development cycle are critical to the success of ramping a new technology node toward profitable high-volume manufacturing. In this paper, a computational patterning software, ProETCH®, has been developed with rigorous physics and advanced algorithms for modeling the etch patterning process, with the featured capabilities in calibrating the reaction mechanisms and optimizing the etch process. A shallow trench isolation etch process using self-aligned double patterning was investigated. A reaction mechanism of silicon etch by Ar/Cl2 plasma was developed to address the surface reactions, and a plasma hypermodel was introduced to correlate process operating conditions to plasma parameters at the wafer surface. The parameters of the reaction mechanism and the plasma hypermodel were calibrated with experimental data obtained from cross-sectional scanning electron microscope (XSEM) images. The calibrated model is used to identify the different fundamental pathways that contribute to the observed profile metrics in XSEMs. The model was then used for process development and optimization by solving the forward and inverse problems. In the forward problem, the model is used to predict the etching profile at different process conditions. Predictions for both interpolation conditions (process parameters within the range used for developing the model) and extrapolation conditions (process parameters outside of the range used for developing the model) agree well with the experimental data with the root mean square error less than 4 nm (1 nm resolution used for the mesh). In the inverse problem, the developed model is used to search for process conditions (e.g., values of bias power and pressure), which could result in desirable profiles. The solutions to the inverse problem demonstrate a degeneracy in process space of the etching process for a given target profile. [ABSTRACT FROM AUTHOR]

Accurate simulations of the shock response of heterogeneous energetic (HE) materials require closure models, which account for energy localization in the micro-structure. In a multi-scale framework, closure is provided by reaction rate models that account for ignition and growth of hotspots, allowing for prediction of the overall macro-scale sensitivity of a HE material. In the present meso-informed ignition and growth (MES-IG) model, the reaction rate is expressed as a function of shock pressure and morphology of the void field in a pressed energetic material. In MES-IG, the void morphology is quantified in terms of a limited number of parameters: viz., overall porosity, void size, and shape (aspect ratio and orientation). In this paper, we quantify the effects of arbitrary variations in void shapes on meso-scale energy deposition rates. A collection of voids of arbitrary shapes is extracted from scanning electron microscope (SEM) images of real, pressed HMX (octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine) samples and classified into groups based on their similarity in shapes. Direct numerical simulations (DNS) are performed on the highly contorted "real" void shapes, and the calculated hotspot ignition and growth rates are compared with values predicted by the MES-IG. It is found that while the parameterization of complex void morphologies in terms of orientation and aspect ratio gives fairly good agreement between DNS and MES-IG reaction rates, the intricate details of highly complex void shapes impact hotspot characteristics to a significant extent. This work suggests possible improvements for the prediction of reaction rate in the energetic microstructure by adopting a more detailed description of shapes. [ABSTRACT FROM AUTHOR]

Piezoresistance, the change of electrical resistance due to applied mechanical strain, has been characterized for films in tension or bending. However, measuring the compressive piezoresistance of films remains a challenge because the in-plane compression often results in macroscopic buckling and kinking, leading to localization of strain. Here, we overcame this issue via a newly developed method to calculate the compressive piezoresistance of films by measuring the change of resistance in situ under tensile and bending stresses. A linear fit was applied to the experimental tensile piezoresistive response and a quadratic fit was applied to the bending piezoresistive response. The experimental bending response was mathematically decomposed into its tensile and compressive components. The compressive response was then isolated by subtracting the tensile response from the bending response. In this study, the method is applied to reduced graphene oxide (rGO) film specimens. For rGO films, the compressive piezoresistance was found to be much greater than the tensile piezoresistance. Scanning electron microscope images revealed that extensive damage occurred on the compressive side of the bending specimen, resulting in a large increase in resistivity. We anticipate that our study will be adapted to applications that require mechanically reliable, flexible, and highly conductive materials, such as flexible electronics and structural energy and power. [ABSTRACT FROM AUTHOR]

We have demonstrated that intense 7-fs, ∼810-nm laser pulses can produce a much finer periodic nanostructure on a diamond-like carbon film through ablation in air than that formed with intense 100-fs, ∼800-nm laser pulses. The minimum period size is ∼60 nm, corresponding to ∼1/13 of the center wavelength. To understand the physical mechanism responsible for the finer nanostructuring, we have observed a bonding structural change in the nanostructure with micro-Raman spectroscopy and a scanning transmission electron microscope. It has been found that the modified layer thickness with the 7-fs pulses is much thinner than that with the 100-fs pulses. The results show that the 7-fs pulses create a few-nm-thick layer with high-density electrons and excite short-range surface plasmon polaritons, which have a large wave number around the layer and induce the plasmonic near-field nanoablation. The period size estimated by using a model target reproduces well the observed size of nanostructures. [ABSTRACT FROM AUTHOR]

SnTe is an important material because of its applications in mid-infrared photo-detectors. In the present work, the effects of film thickness on scaling law and surface properties (i.e., morphologies and optical properties) of SnTe thin films have been investigated. SnTe thin films of different thicknesses are prepared by means of e-beam evaporation technique. The surface morphology of each film is analyzed by atomic force microscopy (AFM) as well as a scanning electron microscope. The crystallinity of the films is found to increase with increasing film thickness, as confirmed by x-ray diffraction and Raman measurements. Fractal analysis is performed on AFM images to investigate the irregularity of surfaces. It is found that the surface of the thicker sample is rougher than the thinner sample. The autocorrelation function is applied to investigate the self-affine fractal nature of surfaces. The average roughness, interface width, lateral correlation length, local surface slope, and fractal dimension increased with film thickness. The values of roughness exponent, growth exponent, dynamic exponent, and steepening exponent are calculated and found to be α = 0.76 - 0.96 , β = 0.75 , z = 1.92 , and λ = 0.35 - 0.25 , respectively. The scaling exponents together with the other parameters such as the local surface slope indicate that the growth is quasi-3D island/mound type with rapid surface roughening behavior and obeys anomalous scaling. The multiple scattering cross sections of light together with Fourier transform infrared spectroscopy data analyses suggest that the higher crystalline film with a smaller number of defects is infrared-sensitive and may be more suitable for advanced mid-infrared detector applications. [ABSTRACT FROM AUTHOR]

A process for growing gallium nitride (GaN) vertical p–i–n homojunctions on (111) silicon substrates using metalorganic chemical vapor deposition was developed, and a triple mesa etch technique was used to fabricate efficient betavoltaic energy converters. Monte Carlo simulation platform CASINO was used to model beta radiation penetration into GaN to aid device design. The resulting devices were tested under irradiation from a scanning electron microscope electron beam (e-beam) tuned to imitate the energies of the 63Ni beta emission spectrum. Based on current–voltage measurements taken under e-beam illumination, a maximum open-circuit voltage of ∼ 412 mV and a maximum short-circuit current density of ∼ 407 nA/cm2 were measured. A high fill factor of ∼ 0.77 and power conversion efficiency of ∼ 6.6 % were obtained. Additionally, the proposed triple mesa etch technique used to create these betavoltaics has the potential for further use in fabricating many types of electronic devices using a wide variety of material platforms. [ABSTRACT FROM AUTHOR]

Perovskite La2Ti2O7 nanocrystalline powder was obtained through the shock synthesis method. In the study, La2O3 and TiO2 powders were mixed through ball milling and, subsequently, shocked by a flyer at a velocity of 3.2 km/s. After shock treatment, the sample was recovered and characterized via various techniques, such as x-ray diffraction, Raman, scanning electron microscope, transmission electron microscope, and ultraviolet-visible diffuse reflection spectrum analysis, to find the presence of La2Ti2O7 nanocrystalline powder with an average grain size of approximately 30 nm in the recovered samples with different yields. Moreover, the results further confirm that the high shock temperature and long ball milling treatment induce higher activation of precursors to improve the La2Ti2O7 content in the recovered samples. By adjusting the relative density of precursor and the ball milling period, pure La2Ti2O7 nanocrystalline powder was obtained. The formation mechanism of La2Ti2O7 was carefully illustrated. This study presents a new method to synthesize La2Ti2O7 nanocrystalline powder by detonation-driven flyer impact. [ABSTRACT FROM AUTHOR]