Search

The primary objective of this experiment was to assess the effect of mouthpiece chamber vacuum on teat-end congestion. The secondary objective was to assess the interactive effects of mouthpiece chamber vacuum with teat-end vacuum and pulsation setting on teat-end congestion. The influence of system vacuum, pulsation settings, mouthpiece chamber vacuum, and teat-end vacuum on teat-end congestion were tested in a 2×2 factorial design. The low-risk conditions for teat-end congestion (TEL) were 40 kPa system vacuum (Vs) and 400-ms pulsation b-phase. The high-risk conditions for teat-end congestion (TEH) were 49 kPa Vs and 700-ms b-phase. The low-risk condition for teat-barrel congestion (TBL) was created by venting the liner mouthpiece chamber to atmosphere. In the high-risk condition for teat-barrel congestion (TBH) the mouthpiece chamber was connected to short milk tube vacuum. Eight cows (32 quarters) were used in the experiment conducted during 0400 h milkings. All cows received all treatments over the entire experimental period. Teatcups were removed after 150 s for all treatments to standardize the exposure period. Calculated teat canal cross-sectional area (CA) was used to assess congestion of teat tissue. The main effect of the teat-end treatment was a reduction in CA of 9.9% between TEL and TEH conditions, for both levels of teat-barrel congestion risk. The main effect of the teat-barrel treatment was remarkably similar, with a decrease of 9.7% in CA between TBL and TBH conditions for both levels of teat-end congestion risk. No interaction between treatments was detected, hence the main effects are additive. The most aggressive of the 4 treatment combinations (TEH plus TBH) had a CA estimate 20% smaller than for the most gentle treatment combination (TEL plus TBL). The conditions designed to impair circulation in the teat barrel also had a deleterious effect on circulation at the teat end. This experiment highlights the importance of elevated mouthpiece chamber vacuum on teat-end congestion and resultant decreases in CA., (Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

Twenty-four Holstein cows, producing at least 21 kg of milk/d, were used in two replicate experiments to determine the effect of presence or absence of pulsation on loss of teat canal keratin during machine milking. Left quarters were milked without pulsation and right quarters were milked with pulsation. On d 0 and 10, keratin was collected from one left and from one right teat canal of each cow prior to milking and from the remaining two teat canals after milking. Milk was collected for assessment of SCC and bacteriological status on d 0 and approximately every 3 d until d 18. Quantity of keratin recovered before milking on d 10 did not differ between teats milked with or without pulsation, but loss of keratin because of milking was greater from teats milked with pulsation. By d 7, 30% (12 of 43) of quarters milked without pulsation had become infected, but no (0 of 47) quarters milked with pulsation were infected. By d 14 to 16, new infections had increased to 68% (28 of 41) of quarters milked without pulsation and 2% (1 of 43) in quarters milked with pulsation; mean SCC in pulsationless quarters increased sevenfold relative to pulsation quarters. Protein and water content of keratin did not differ because of treatment, and changes in lipid composition were minor. Histological analysis of the teats of 4 cows indicated that the mean diameter of the teat canal, within 2 h after milking, was greater without pulsation than with pulsation (680 vs. 483 microns).

The principles for milking the 13,600-kg (30,000-lb) cow are the same as for any other dairy cow: she should be milked gently, quickly, and completely with minimal machine stripping or over-milking. The application of these principles may differ, however, because high producing cows have 1) lower premilking stimulus requirements than low producers, 2) higher peak milking rates and higher average flow rates (yet longer times to milkout), 3) higher incidence of teat orifice lesions such as hyperkeratosis, and 4) higher risk of new mastitis infections. Existing national and international standards for construction and performance of milking systems may not be adequate to manage the higher expected flow rates through the milking unit and milklines. Such standards need to be reviewed and perhaps revised to ensure appropriate sizing and flow characteristics based on sound engineering principles and physiological requirements. Milking four times per day increases daily milk production compared with twice per day, and milking eight times per day increased daily production compared with four times per day. Cows milked more than four times per day might not require complete milking out at every milking. More frequent milking (or milking on demand) may be achieved with robot milkers, provided that robots can match the reliability of human milkers.

Machine-induced changes in diameter, thickness, and compressibility of the teat apex and teat barrel were measured on all teats of four cows milked at vacuums of 25, 30, 40, and 50 kPa. Measurements were made with an electronic caliper instrument immediately before milking and then at .5, 15, and 30 min after milking. Teat length was also measured at these times. Immediately after milking, for the two higher levels, teats were significantly thicker (7 to 10% thicker at 40 kPa, 17 to 25% at 50 kPa), shorter (by 3 to 6 mm), smaller in diameter (by 2 to 4 mm for the apex, 3 to 6 mm for the barrel), and less compressible for all milking treatments compared with the premilking status for individual teats. Although teat thickness recovered to the premilking mean values 30 min after milking at 40 or 50 kPa, the barrel still was significantly thicker after 30 min compared with those at the lower vacuum treatments. We suggest that changes in teat length, diameter, thickness, and compressibility after milking at low vacuum levels mainly reflect tissue responses to udder evacuation. In contrast, increased teat wall thickness and reduced compressibility of teat tissue at higher vacuum levels likely result mainly from machine-induced edema.