Search

Tobacco use is the leading preventable cause of premature disease and death in the United States. Approximately, 34 million U.S. adults currently smoke cigarettes. We developed a method for automated sample preparation and liquid chromatography-tandem mass spectrometry quantitation of 14 tobacco-related analytes: nicotine (NICF), cotinine (COTF), trans-3′-hydroxycotinine (HCTF), menthol glucuronide (MEG), anabasine (ANBF), anatabine (ANTF), isonicoteine (ISNT), myosmine (MYOS), beta-nicotyrine (BNTR), bupropion (BUPR), cytisine (CYTI), varenicline (VARE), arecaidine (ARD), and arecoline (ARL). The method includes automated solid-phase extraction using customized positive-pressure functions. The preparation scheme has the capacity to process a batch of 96 samples within 4 h with greater than 88% recovery for all analytes. The 14 analytes, separated within 4.15 min using reversed-phase liquid chromatography, were determined using a triple-quadrupole mass spectrometer with atmospheric-pressure chemical ionization and multiple reaction monitoring in negative and positive ionization modes. Wide quantitation ranges, within 1.2–72,000 ng/mL, were established especially for COTF, HCTF, MEG, and NICF to quantify the broad range of biomarker concentrations found in the U.S. population. The method accuracy is above 90% while the overall imprecision is below 7%. Finally, we tested urine samples from 90 smokers and observed detection rates of over 98% for six analytes with urinary HCTF and MEG concentrations ranging from 200–14,100 and 60–57,100 ng/mL, respectively. This high throughput analytical process can prepare and analyze a sample in 9 min and along with the 14-compound analyte panel can be useful for tobacco-exposure studies, in smoking-cessation programs, and for detecting changes in exposure related to tobacco products and their use.

A stable, protein C activating membrane-mimetic film was produced on a polyelectrolyte multilayer (PEM) by in-situ photopolymerization of a phospholipid assembly containing thrombomodulin (TM). The monoacrylated phospholipid monomer was initially synthesized and prepared as unilamellar vesicles with varying molar concentrations of TM. Notably, in mixed-lipid systems, K m values for protein C activation increased in direct proportion to the mole fraction of polymerizable lipid, which was likely due to reduced membrane mobility after photopolymerization. Membrane-mimetic films were also constructed on planar substrates with predictable surface concentrations of catalytically active TM. Significantly, at a TM surface concentration of 170 fmol/cm 2 , the rate of protein C activation was comparable to that measured for a variety of confluent endothelial cell monolayers. Serial measurements of contact angles and protein C activation confirmed short-term film stability under a variety of in vitro conditions. Moreover, 1 2 5 I labeling of TM demonstrated little change in TM surface concentration over periods of up to 28 days. Significantly, polymeric lipid membranes functionalized with thrombomodulin efficiently inhibited thrombin generation. We believe that the design of membrane-mimetic films that have the capacity to activate the protein C pathway will provide a useful strategy for generating "actively" antithrombogenic surfaces.

A stabilized, membrane-mimetic film was produced on a polyelectrolyte multiplayer (PEM) by in-situ photopolymerization of an acrylate functonalized phospholipid assembly at a solid-liquid interface. The phospholipid monomer was synthesized, prepared as unilamellar vesicles, and fused onto close-packed octadecyl chains as part of an amphiphilic terpolymer anchored onto the PEM by electrostatic interactions. The lipid film displayed an advancing contact angle of ∼ 60°, elemental composition, as determined by X-ray photoelectron spectroscopy, was in agreement with that anticipated for a lipid membrane. Data obtained from both high-resolution scanning electron microscopy and ellipsometry were consistent with the formation of a supported lipid monolayer. In addition, polarized external reflection infrared spectroscopy revealed significant acyl chain ordering induced on lipid fusion and polymerization. Doping the lipid assembly with a fluorescein terminated polymerizable lipid provided visible confirmation of film formation and its stability under a variety of conditions, including shear rates of 2000 sec - 1 . Transport studies demonstrated that the addition of a lipid film significantly reduced barrier permeability for compounds in excess of 70 kD. The ability to coat microbeads (d ∼ 300 μm) with a robust membrane-mimetic film, while preserving encapsulated cell viability is illustrated, thereby establishing a new strategy for modulating the physiochemical and biological properties of immunoisolation barriers for cell transplantation.