Search

Fluorenylboronate ester chromophore-based thin films were investigated for the detection of triacetone triperoxide (TATP) vapors via the decomposition product, hydrogen peroxide. Sensing with a high level of sensitivity was achieved using a fluorescence "turn-on" mechanism based on the significant shifts in the absorption and photoluminescence spectra that occurs when the boronate esters were converted to phenoxides by hydrogen peroxide under basic conditions. The addition of an organic base was found to be critical for achieving fast conversion reactions and the formation of the phenoxide anions. Addition of a nitrile group to the fluorenyl boronate ester moiety improved the stability of the material to photooxidation, increased the photoluminescence quantum yields, and enhanced the absorption and emission shifts to longer wavelengths. In real-time sensing measurements, films comprising the cyanofluorenyl boronate ester moiety and tetra- n-butylammonium hydroxide had a response time to acid-decomposed TATP vapor of seconds and a limit of detection of 40 ppb in 60 s.

PNNT has been prepared as a polymeric electron acceptor for organic solar cells. The polymer has an A-A'-A acceptor motif linked alternatively with thiophene and vinyl moieties. The A'-unit is a naphthalene diimide, while the A groups are thiazoles. PNNT films were found to have an estimated electron affinity of ≈4.3 eV and an electron mobility of the order of 10 -4 cm 2 V -1 s -1 . Its relatively low solubility in common chlorinated solvents at ambient temperature allowed the manufacture of sequentially deposited (SD) devices, which were found to have significantly higher efficiency than that of bulk heterojunction (BHJ) solar cells containing the same materials. Grazing-incidence wide-angle X-ray scattering measurements indicated that the SD films retained the ordering of the individual polymers to a greater extent compared to the BHJ films. The best SD devices were found to have a power conversion efficiency of up to 4.5%, with stable performance under thermal stress.

Transient absorption spectroscopy on organic semiconductor blends for solar cells typically shows efficient charge generation within ∼100 fs, accounting for the majority of the charge carriers. In this Letter, we show using transient absorption spectroscopy on blends containing a broad range of acceptor content (0.01-50% by weight) that the rise of the polaron signal is dependent on the acceptor concentration. For low acceptor content (<10% by weight), the polaron signal rises gradually over ∼1 ps with most polarons generated after 200 fs, while for higher acceptor concentrations (>10%) most polarons are generated within 200 fs. The rise time in blends with low acceptor content was also found to be sensitive to the pump fluence, decreasing with increasing excitation density. These results indicate that the sub-100 fs rise of the polaron signal is a natural consequence of both the high acceptor concentrations in many donor-acceptor blends and the high excitation densities needed for transient absorption spectroscopy, which results in a short average distance between the exciton and the donor-acceptor interface.

We have used steady-state and time-resolved neutron reflectometry to study the diffusion of fullerene derivatives into the narrow optical gap polymer poly[N-9″-hepta-decanyl-2,7-carbazole-alt-5,5-(4',7'-di-2-thienyl-2',1',3'-benzothiadiazole)] (PCDTBT) to explore the sequential processing of the donor and acceptor for the preparation of efficient organic solar cells. It was found that when [6,6]-phenyl-C61-butyric-acid-methyl-ester (60-PCBM) was deposited onto a thin film of PCDTBT from dichloromethane (DCM), a three-layer structure was formed that was stable below the glass-transition temperature of the polymer. When good solvents for the polymer were used in conjunction with DCM, both 60-PCBM and [6,6]-phenyl-C71-butyric-acid-methyl-ester (70-PCBM) were seen to form films that had a thick fullerene layer containing little polymer and a PCDTBT-rich layer near the interface with the substrate. Devices composed of films prepared by sequential deposition of the polymer and fullerene had efficiencies of up to 5.3%, with those based on 60-PCBM close to optimized bulk heterojunction (BHJ) cells processed in the conventional manner. Sequential deposition of pure components to form the active layer is attractive for large-area device fabrication, and the results demonstrate that this processing method can give efficient solar cells.