Search

Hydrogels, typically favored for 3D printing due to their viscoelasticity, are now trending toward ecofriendly alternatives amid growing environmental concerns. In this study, we crafted cellulose-based hydrogels, specifically employing cellulose acetate sulfate (CAS). By keeping the acetyl group substitution degree (DS acetyl = 1.8) and CAS molecular weight constant, we varied rheological properties by adjusting sulfate group substitution (DS sulfate = 0.4, 0.7, and 1.0) and CAS concentration (2-5 wt %). Rheological characterizations, including shear-thinning, yield stress, and thixotropy, were performed to identify optimal conditions for formulating CAS hydrogel ink in direct ink writing for 3D printing under selected experimental conditions. Based on rheological findings, CAS hydrogels with DS sulfate 0.7 and concentration of 4 wt % was used for 3D printing, with subsequent evaluation of printing metrics. Additionally, the effect of ionic cross-linking using Ca 2+ ions on the structural integrity of 3D-printed structures was evaluated, demonstrating effective preservation through reinforced polymer networks. The shrinking and swelling behaviors of the 3D-printed structures were also significantly affected by this ionic cross-linking. Building on these findings, this work could broaden the range of cellulose derivatives available for the preparation of cellulose-based hydrogels for 3D printing.

Deposition of hydrophobic wood extractives and representative model compounds, on the surface of cellulose prior to enzymatic hydrolysis was found to either enhance or inhibit the action of cellulase enzymes. The effect of these compounds was correlated with their chemical structure, which may in part explain the differential effects observed between softwood and hardwood extractives. Specifically, the addition of sterol, enhanced enzymatic hydrolysis of microcrystalline cellulose by 54%, whereas the addition of a triglyceride could inhibit the hydrolysis by 49%. The effects of the different extractives' could be explained by considering their Hansen solubility parameters. The amphiphilic and/or hydrophobic character of model extractives was found to be the variable that affected the deposition of extractives on cellulose surfaces and the eventual adsorption of cellulolytic enzymes on it. The observed beneficial effects of extractives are likely related to a reduction in the irreversible binding of the enzymes on the cellulose surface.

Ultrathin bicomponent films of cellulose and lignin derivatives were deposited on silica supports by spin coating, and after conversion into the respective polymer precursor, they were used as a model system to investigate interfacial phenomena relevant to lignocellulose biocatalysis. Film morphology, surface chemical composition, and wettability were determined by atomic force microscopy, X-ray photoelectron spectroscopy, and water contact angle, respectively. Phase separation of cellulose and lignin produced structures that resembled the cell wall of fibers and were used to monitor enzyme binding and cellulolytic reactions via quartz crystal microgravimetry. The rate and extent of hydrolysis was quantified by using kinetic models that indicated the role of the surface lignin domains in enzyme inhibition. Hydrophobic interactions between cellulases and the substrates and their critical role on irreversible adsorption were elucidated by using acetylated lignin films with different degrees of substitution. Overall, it is concluded that sensors based on the proposed ultrathin films of lignocellulose can facilitate a better understanding of the complex events that occur during bioconversion of cellulosic biomass.

Model cellulose surfaces based on cellulose nanocrystals (CNs) were prepared by the Langmuir-Schaeffer technique. Cellulose nanocrystals were obtained by acid hydrolysis of different natural fibers, producing rodlike nanoparticles with differences in charge density, aspect ratio, and crystallinity. Dioctadecyldimethylammonium bromide (DODA-Br) cationic surfactant was used to create CN-DODA complexes that allowed transfer of the CNs from the air/liquid interface in an aqueous suspension to hydrophobic solid substrates. Langmuir-Schaeffer horizontal deposition at various surface pressures was employed to carry out such particle transfer that resulted in CN monolayers coating the substrate. The morphology and chemical composition of the CN films were characterized by using atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). Also, their swelling behavior and stability after treatment with aqueous and alkaline solutions were studied using quartz crystal microgravimetry (QCM). Overall, it is concluded that the Langmuir-Schaeffer method can be used to produce single coating layers of CNs that were shown to be smooth, stable, and strongly attached to the solid support. The packing density of the films was controlled by selecting the right combination of surface pressure during transfer to the solid substrate and the amount of CNs available relative to the cationic charges at the interface.