Search

The patterning of gold nanoparticles (GNPs) on the surface of a fluoropolymer substrate by using patterned surface grafting and layer-by-layer deposition techniques is described. The surface of a poly(tetrafluoroethylene-co-perfluorovinyl ether) (PFA) substrate was selectively implanted with 150 keV proton ions. Peroxide groups were successfully formed on the implanted PFA surface, and their concentration depended on the fluence. Acrylic acid was graft polymerized onto the implanted regions of the PFA substrate, resulting in well-defined patterns of poly(acrylic acid) (PAA) on the PFA substrate. The surface properties of the PAA-patterned PFA surface, such as chemical compositions, wettability, and morphology, were investigated. The surface analysis results revealed that PAA was definitely present on the implanted regions of the PFA surface, and the degree of grafting was dependent on three factors: fluence, grafting time, and monomer concentration. Furthermore, GNP patterns were generated on the prepared PAA-patterned PFA surface by layer-by-layer deposition of GNPs and poly(diallyldimethyl ammonium chloride). The multilayers of GNPs were deposited only onto the PAA-grafted regions separated by bare PFA regions, and the resulting GNP patterns exhibited good electrical conductivity.

In this study, a facile and effective method for the surface functionalization of inert fluoropolymer substrates using surface grafting was demonstrated for the preparation of a new platform for fluorescence-based bioassays. The surface of perfluorinated poly(ethylene-co-propylene) (FEP) films was functionalized using a 150 keV ion implantation, followed by the graft polymerization of acrylic acid, to generate a high density of carboxylic acid groups on the implanted surface. The resulting functionalized surface was investigated in terms of the surface density of carboxylic acid, wettability, chemical structure, surface morphology, and surface chemical composition. These results revealed that poly(acrylic acid) (PAA) was successfully grafted onto the implanted FEP surface and its relative amount depended on the fluence. To demonstrate the usefulness of this method for the fabrication of bioassays, the PAA-grafted FEP films were utilized for the immobilization of probe DNA for anthrax toxin, followed by hybridization with Cy3-labeled target DNA. Liver cancer-specific α-feto-protein (AFP) antigen was also immobilized on the PAA-grafted FEP films. Texas Red-labeled secondary antibody was reacted with AFP-specific primary antibody prebound to the AFP antigen using an immunoassay method. The results revealed that the fluorescence intensity clearly depended on the concentration of the target DNA hybridized to the probe DNA and the AFP antigen immobilized on the FEP films. The lowest detectable concentrations of the target DNA and the AFP antigen were 10 fg/mL and 10 pg/mL, respectively, with the FEP films prepared at a fluence of 3 × 10(14) ions/cm(2).

A simple and controllable one-step method to fabricate superhydrophobic surfaces on poly(tetrafluoroethylene) (PTFE) films is developed on the base of electron irradiation. When the thickness of PTFE films is higher than the penetration depth of electron beams, electrical charging occurs at the surface of the films because of the imbalance between the accumulation of incident electrons and the emission of secondary electrons. Local inhomogeneity of charge distribution due to this electrical charging results in the nonuniform decomposition of PTFE molecular bonds. As electron fluence increases, surface morphology and surface roughness of the films are dramatically changed. An extremely rough surface with micrometer-sized pores is produced on the surface of PTFE films by electron irradiation at a fluence higher than 2.5 × 10(17) cm(-2).Because of high surface roughness, the irradiated PTFE films exhibit superhydrophobic property with a water contact angle (CA) greater than 150° at fluences ranging from 4 × 10(17) to 1 × 10(18) cm(-2). The surface morphology and corresponding water CA can be controlled by simply changing the electron fluence. This electron irradiation method can be applicable to the fabrication of superhydrophobic surfaces using other low-surface-energy materials including various fluoropolymers.

The surface of a poly(ethylene terephthalate) (PET) film was selectively irradiated with proton beams at various fluences to generate carboxylic acid groups on the surface; the resulting functionalized PET surface was then characterized in terms of its wettability, chemical structure, and chemical composition. The results revealed that (i) carboxylic acid groups were successfully generated in the irradiated regions of the PET surface, and (ii) their relative amounts were dependent on the fluence. A capture biomolecule, anthrax toxin probe DNA, was selectively immobilized on the irradiated regions on the PET surface. Cy3-labeled DNA as a target biomolecule was then hybridized with the probe DNA immobilized on the PET surface. Liver-cancer-specific α-fetoprotein (AFP) antigen, as a target biomolecule, was also selectively immobilized on the irradiated regions on the PET surface. Texas Red-labeled secondary antibody was then reacted with an AFP-specific primary antibody prebound to the AFP antigen on the PET surface for the detection of the target antigen, using an indirect immunoassay method. The results revealed that (i) well-defined micropatterns of biomolecules were successfully formed on the functionalized PET surfaces and (ii) the fluorescence intensity of the micropatterns was dependent mainly on the concentrations of the target DNA hybridized to the probe DNA and the target AFP antigen immobilized on the PET films. The lowest detectable concentrations of the target DNA and target AFP antigen in this study were determined to be 4 and 16 ng/mL, respectively, with the PET film prepared at a fluence of 5 × 10(14) ions/cm(2).

A noncytotoxic procedure for the spatial organization of multiple cell types remains as a major challenge in tissue engineering. In this study, a simple and biocompatible micropatterning method of multiple cell types on a polymer surface is developed by using ion implantation. The cell-resistant Pluronic surface can be converted into a cell-adhesive one by ion implantation. In addition, cells show different behaviors on the ion-implanted Pluronic surface. Thus this process enables the micropatterning of two different cell types on a polymer substrate. The micropatterns of the Pluronic were formed on a polystyrene surface. Primary cells adhered to the spaces of the bare polystyrene regions separated by the implanted Pluronic patterns. Secondary cells then adhered onto the implanted Pluronic patterns, resulting in micropatterns of two different cells on the polystyrene surface.

5-(2,6-difluorobenzyl)oxymethyl-5-methyl-3-(3-methylthiophen-2-yl)-1,2-isoxazoline derivative was synthesized, and its herbicidal activity was assessed under glasshouse and flooded paddy conditions. 5-(2,6-Difluorobenzyl)oxymethyl-5-methyl-3-(3-methylthiophen-2-yl)-1,2-isoxazoline demonstrated good rice selectivity and potent herbicidal activity against annual weeds at 125 g of a.i. ha(-1) under greenhouse conditions. Soil application of this compound showed complete control of barnyard-grass to the fourth leaf stage at 250 g of a.i. ha(-1). Field trials indicated that this compound controlled annual weeds rapidly with a good tolerance on transplanted rice seedlings by post-emergence and soil application. This compound showed a low mammalian and environmental toxicity in various toxicological tests.