Search

Recent research has demonstrated that additive manufacturing (AM) can be used to produce directionally sensitive high explosives (HEs), but detonation wave propagation in AM HEs with variable internal structure has not been studied. In this work, samples were printed using a 73 wt. % octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine-based HE ink. Flash x-ray radiography imaging was used to observe density changes in two imaging planes of each sample during detonation, and high-speed imaging was used to calculate the detonation velocity at the HE surface. The detonation front initially appears to fail in internal channel regions of the HE, but late reactions occurred in two samples, which increased the material bulk density by 2.8%, possibly due to shock convergence phenomena. The calculated detonation wave pressure similarly increased, but the accuracy of the results is uncertain because of the deviation of the low bulk density printed samples from the cast charge principal isentrope. This work demonstrates that structure can be effectively utilized to guide detonation wave propagation through HE charges.

One of the key fundamental issues that is crucial in the continuum modeling of reactive flow phenomena is the thermodynamically consistent description of reaction mixture properties. To define the mixture properties, thermodynamic closure rules that relate the properties of the individual reaction components to the mixture properties are required. In the context of reactive two-phase modeling approaches, various strategies to define the thermodynamic closures have been adopted such as pressure temperature (PT) equilibrium between the individual reaction components, pressure (specific) volume (PV) equilibrium, etc. The choice of closure rules determines the relative distribution of specific volume and energy across the reaction components that comprise the mixture. Therefore, depending on the choice of the closure, the mixture thermodynamic behavior can vary. The present work examines the effect of different closure approaches on the thermodynamic properties of the reaction mixture. The analysis is performed for a condensed phase HMX (octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine) based plastic bonded explosive (PBX) 9501 explosive using four different thermodynamic closures, viz., PT equilibrium, PV equilibrium, volume temperature (VT) equilibrium, and pressure (P) equilibrium with reactants on an isentrope. The relative variations in the thermodynamic properties of the mixture are analyzed and compared under both compression and expansion loading regimes. It is shown that out of the four closure models, only PT equilibrium and P equilibrium closures lead to a thermodynamically accurate description of the mixture under both compression and expansion.

Graded density impactors (GDIs) are multi-material composite impactors used in gas gun experiments to tailor the drive conditions imparted to a sample test material. Previous graded density impactors generally rely on thin, but discrete, layers of different materials. The thinner and the greater number of layers will result in smoother compression. Taken to the limit of very thin layers would be pure material 1 at one surface, such as the front surface of an impactor, smoothly transitioning at the atomic scale to pure material 2 on the back surface. Such an impactor can initially shock, then smoothly compresses a material during a dynamic experiment. This type of experiment can serve to explore a larger region of thermodynamic space than a single or even multi-shock experiments. An overview of how graded density impactors are made is reviewed and sample results are given. A strategy for modeling these kinds of impactors is presented. The length scales of constituent mixing are given from the experimental build through electrochemical-deposition. Equation of state models for pure constituents and their subsequent mixtures are presented. It is demonstrated that the time scales for pressure and temperature equilibration, for atomically mixed GDIs, are short enough to be a justifiable closure for the resulting multiphase flow. Furthermore, we present simulation results of dynamic shock followed by a ramp compression, utilizing a silver/gold graded density impactor, onto a tantalum sample.

A calibration of the AWSD (Arrhenius Wescott-Stewart-Davis) reactive flow model, applied to the HMX based explosive PBX 9501 is presented. Requisite equation of state parameters for the high explosive reactants and products are based on a combination of experimental data and theoretical calculations. The experimental data needed to calibrate the reaction rate model, specifically shock to detonation transition and detonation propagation at a variety of initial temperatures, are presented along with model results and planned future activities.

A novel set of experiments and reactive flow modeling of pentaerythritol tetranitrate (PETN) is presented. Here, the specific phenomenon of shock to detonation transition is examined, where an initial, relatively weak shock is propagated into pressed PETN powder at 1.65 g/cm 3 and the subsequent buildup to detonation is observed experimentally. These experiments, in conjunction with reactant and products’ equations of state, are utilized for building reactive flow models.

A reactive flow model for the tri-amino-tri-nitro-benzene (TATB) based plastic bonded explosive PBX 9502 (95% TATB, 5% polymeric binder Kel-F 800) is presented. This newly devised model is based primarily on the shock temperature of the material, along with local pressure, and accurately models a broader range of detonation and initiation scenarios. Specifically, sensitivity changes to the initial explosive temperature are accounted for naturally and with a single set of parameters. The equation of state forms for the reactants and products, as well as the thermodynamic closure of pressure and temperature equilibration, are carried over from the Wescott-Stewart-Davis (WSD) model [Wescott et al., J. Appl. Phys. 98, 053514 (2005) and “Modeling detonation diffraction and dead zones in PBX-9502,” in Proceedings of the Thirteenth International Detonation Symposium (2006)]. This newly devised model, with Arrhenius state dependence on the shock temperature, based on the WSD equation of states, is denoted by AWSD. Modifying an existing implementation of the WSD model to the AWSD model in a hydrocode is a rather straightforward procedure.

Raman spectra and velocimetry of shocked PBX 9502 (plastic bonded explosive composed of 95% triaminotrinitrobenzene (TATB) and 5% 3M Company Kel F-800 polymer binder) are reported with the Stokes/anti-Stokes ratio used to determine temperature after the shock reflects from a lithium fluoride window. Final pressures up to 14.5 GPa were tested, but the pressure induced absorption of TATB caused the Raman signal to decrease exponentially with pressure. The reflected shock temperature could be determined to 7 GPa, with an average increase of 14.9 K/GPa. Suggestions to adapt the technique to permit thermometry at higher temperatures are discussed, as are comparisons to a recently proposed equation of state for PBX 9502.

The response of high explosives (HEs), due to mechanical and/or thermal insults, is of great importance for both safety and performance. A major component of how an HE responds to these stimuli stems from its reactant equation of state (EOS). Here, the tri-amino-tri-nitro-benzene based explosive PBX 9502 is investigated by examining recent experiments. Furthermore, a complete thermal EOS is calibrated based on the functional form devised by Wescott, Stewart, and Davis [J. Appl. Phys. 98, 053514 (2005)]. It is found, by comparing to earlier calibrations, that a variety of thermodynamic data are needed to sufficiently constrain the EOS response over a wide range of thermodynamic state space. Included in the calibration presented here is the specific heat as a function of temperature, isobaric thermal expansion, and shock Hugoniot response. As validation of the resulting model, isothermal compression and isentropic compression are compared with recent experiments.