Search

A powerful neutral beam system with six high current H− ion sources achieved a total power of 10.3 MW in the large helical device (LHD). We describe the present status of the ion sources, and the results of studies of cesium consumption, tungsten filament lifetime, and the velocity spectrum of the beam. Maximum power and beam energy in those ion sources range from 3.5 to 4.4 MW and 165 to 180 keV (design energy), respectively. The maximum H− current is ∼25 A. Much progress on beam acceleration and plasma uniformity was facilitated by a new accelerator and new arc power supply system with careful Cs seeding. Cs consumption for 1/2 year of operation ranges from 3.9 to 10.6 g per one source (over 2×104 shots). It is converted to the rate of 0.17–1.5 mg per one shot per source. It is considered that Cs deposition on the inside surface of the plasma source could be from 0.11 to 1.0 monolayer per one shot per source. This is of the same order as the expected optimum coverage of ∼0.7. Filament weight loss was me...

In this article we describe the first results of beam injection using an improved negative ion source, which consists of a set of steering and multislot grounded grids. The set of the grids is designed to achieve high power beam injection for the large helical device (LHD). The main purpose in replacing the conventional multiaperture with multislot grids is to reduce the heat load onto the grid. By adopting the multislot grid, the frequency of voltage breakdown at the acceleration gap decreased considerably and the maximum beam energy attained was 180 keV, which is one of the target values of the LHD neutral beam injector (NBI). The maximum injection power reached 4.4 MW, consequently. The heat load onto the multislot grid was water calorimetrically measured and the load is suppressed by 50% compared to the multiaperture case. In the condition for maximum injection power, the beam profile obtained in the accelerator with the multislot grounded grid becomes vertically elongated due to the asymmetric electric field close to the grid slot. Although some part of this elongated beam is lost at the injection port, the multislot grid has enough performance for beam injection.

The Large Helical Device-Neutral Beam Injector (LHD-NBI) system uses 40 A×180 keV (10 s) negative hydrogen ion sources. Three studies of the H− ion source are reported, i.e., conditioned status, co-accelerated electron beam component, and weight loss of tungsten filaments. Total injection numbers through experimental cycles sum up to ∼8000 shots with four ion sources on two beam lines. Injection power reached a maximum of 5.2 MW. The maximum energy achieved was 171 keV. A pulse length up to 80 s was reached with 0.5 MW. Electron fraction in the accelerated H− beam was evaluated by measuring the heat load on the electron beam dump. Total fraction of the power in the electron beam component deposited on the dump was evaluated to be 1.5%–6% with up to ∼1 Pa of H2. Stripped electrons which were produced inside acceleration gap comprised the majority compared to electrons extracted from source plasma. The weight loss of tungsten filament was 0.01–0.103 mgr/shot/filament. The total loss was ∼0.5% after ∼6500 sh...

A fast response calorimeter has been developed for the neutral-beam (NB) shine-through measurement. This calorimeter has the following advantages. (1) Temporal variation of the heat load onto the calorimeter can be measured. (2) Measurement under the relatively high heat flux environment is possible. (3) The calorimetric measurement under continuous and steady-state heat load environment is also possible. The verification of the measurement principle was done using an NB-injection system on the compact helical system (CHS) at the National Institute for Fusion Science (NIFS). The measured NB power densities are compared to the power densities being evaluated by the CHS-NB profile database. It was experimentally confirmed that the time constant of the measurement is about 7 ms.

The neutral beam (NB) shine-through profile is routinely monitored on the Large Helical Device (LHD) both to calibrate the port-through power of the NB and to evaluate the NB-deposition power to LHD plasmas. The profile is measured with a calorimeter (CM) array on an armor plate of the NB counter wall inside the LHD vacuum vessel. An infrared camera is also used to check the beam profile where CMs are not located, and measures a temperature increase of the armor plate due to the NB heat load. The measured beam profile is compared to the calculated NB profile at the armor plate. The measurement indicates that the beam is not uniform at the exit of the ion source and that the steering angle of the beam in the horizontal direction is not the same as the designed value. It is found that the monitoring of the NB shine-through profile is important to estimate the NB port-through power and the NB deposition power, especially when the neutral beam injector (NBI) is based on a large negative-hydrogen ion source.

A compact cesium deposition system was used for direct deposition of cesium atoms and ions onto the inner surface of the 1/3 scale hydrogen negative ion source for the large helical device-neutral beam injection (LHD-NBI), system. A small, well defined amount of cesium deposition in the range of 3–200 mg was tested. Negative ion extraction and acceleration were carried out both in the pure hydrogen operation mode and in the cesium mode. Single Cs deposition of 3–30 mg to the plasma chamber has produced temporary 2–5 times increases of H− yield, but the yield was decreased within several discharge pulses to the previous steady-state value. Two consecutive 30 mg depositions done within a 3–5 h/60 shot interval, produced a similar temporary increase of H− beam, but reached a large H− yield steady-state value. Deposition of larger 0.1–0.2 g Cs portions with a 20–120 h/150–270 shot interval improved the H− yield for a long (2–5 days) period of operation. Directed depositions of Cs to the various walls of the p...

Accelerated electrons, which would lead to high thermal load of grids, have been suppressed in a high-current large hydrogen negative ion source. An extraction grid, with apertures shaped as the secondary electrons generated on the grid aperture surface would be shielded against the acceleration electric field, works well to prevent the secondary electrons from leaking to the acceleration gap, compared with a straight aperture extraction grid. Although the strong magnetic field at the extraction grid also lowers the electron leakage downstream, the aperture shaping of the extraction grid is more effective for the suppression of the accelerated electrons. The acceleration efficiency, defined by the ratio of the negative-ion current to the acceleration drain current, is improved to around 85%. There remains the accelerated electrons generated in the negative ion neutralization by collision with the residual neutral molecules during the acceleration. The direct interception of the accelerated negative ions w...

A high-power large negative ion source has been operated for a long pulse duration. A three-grid single-stage accelerator is used, where the extraction grid is shaped so that the secondary electrons generated on the extraction grid would be prevented from leaking into the acceleration gap. A stable long-pulse arc discharge with an arc power of 100 kW has been obtained over 15 s by balancing an individual arc current flowing through each filament. The cesium-seeded operation is not influenced by a temperature rise over 100 °C of the plasma grid during the long-pulse arc discharge. As a result, 330 kW (91 keV–3.6 A) of the negative ion beam was produced stably for 10 s from an area of 25 cm×26 cm, where the current density was 21 mA/cm2 and the negative ion power density was 1.9 kW/cm2. The neutralization efficiency of accelerated negative ions has been measured including the residual positive and negative ion ratios by the water calorimetry of the beam dumps. The result agrees well with the calculation result.

Multipower supplies for the arc discharge are installed to improve beam uniformity of a large size of the neutral beam injection system in the large helical device (LHD). The plasma tends to shift on the upper side of the arc chamber when the same arc voltage is applied to all filaments. The arc discharge current distribution becomes uniform as a consequence of the individual voltage control, but about 20 V difference of the arc voltage between the top and bottom circuits is required. We have estimated the beam profile from each acceleration grid by comparing the calculation and measurement of the beam profile of Halpha and calorimeter. The uniformity of arc discharge has been improved in most regions without the discharge adjustment by a horizontal filament connection. The controllability of the arc discharge distribution of the horizontal filament connection is better than that of the vertical filament connection. The efficiency of the beam production is improved by about 10% in the case of the horizontal filament connection. As a result 3.7 MW of the beam injection has been achieved in the LHD 6th experimental campaign in 2003.

Studies of a multicusp source were recently done at the National Institute for Fusion Science by plasma grid masking. The maximal H− ion yield is ∼1.4 times greater for the shutter mask case than that for the standard source. Negative ion current evolution during the cesium feed to the masked plasma grid evidenced that about 60% of negative ions are produced on the shutter mask surface, while about 30% are formed on the plasma grid emission hole edges, exposed by cesium with the mask open.

Intense H− beams have been extracted from a large multicusp plasma source operated with cesium seeding. The H− beams were accelerated up to 100 keV by a single‐stage or a two‐stage electrode system. Spatial profiles of the beams are measured calorimetrically and the beam divergence angle is obtained from half of the e‐folding width. A minimum beam divergence angle of 5 mrads is achieved at a H− current density of 30 mA/cm2 with a beam energy of 100 keV. The ratio of acceleration current to H− current increases abruptly when a H− current saturates in the space charge limited region. This enhancement is mainly due to secondary electrons caused by the intersection of H− beams with an extraction grid. When the operating gas pressure decreases, the ratio of the acceleration current to the H− current decreases. This is related to a stripping loss of H− ions in the electrodes. A beam divergence angle reaches a minimum when a ratio of Vacc to Vext is set at an optimum value of 1.6 in the single‐stage acceleration...

Multibeamlet focusing of an intense negative‐ion beam has been performed using beamlet steering by aperture displacement. The apertures of the grounded grid were displaced as all 270 beamlets (18×15) in an area of 25 cm×26 cm are steered to a common point (a focal point) in both the two‐stage and the single‐stage accelerators. The multibeamlets were successfully focused and the e‐folding half width of 10 cm was achieved 11.2 m downstream from the ion source in both accelerators. The corresponding gross divergence angle is 9 mrad. The negative‐ion beamlets are deflected by the electron deflection magnetic field at the extraction grid and the deflection direction reverses line by line, resulting in the beam splitting in the deflection direction. This beamlet deflection was well compensated also using beamlet steering by the aperture displacement of the grounded grid. The beam acceleration properties related to the beam divergence and the H− ion current were nearly the same for both the two‐stage and the single‐stage accelerators, and were dependent on the ratio of the extraction to the acceleration electric fields.

A cesiated hydrogen hollow cathode (CHC) was tested for plasma injection in the multicusp negative ion source (MS). The CHC arc with hydrogen feed and cesium seeding through the CHC volume was explored. One cathode unit (40 mm length, 19 mm in diameter, emission opening area 1–3 mm2) with no special cooling provided the MS discharge operation with direct current up to 30 A, and up to 60 A in the long-pulse mode. High efficiency of negative ion production in the MS discharge, driven by a CHC plasma injection was recorded.

For compensation of the magnetically deflected beamlets, a new type of grid system has been applied to a large negative ion source of a negative-ion-based neutral beam injector in the Large Helical Device (LHD) fusion experimental machine. Corresponding to deviation of the negative ion beamlet trajectory due to the electron suppression magnetic field at the extraction grid, the exit aperture of the extraction grid is displaced to cancel the beamlet deflection by electrostatic lens effect. As a result, the beamlet deflection was suppressed less than 2 mrad in a wide range of energy of 110–180 keV, and the port-through efficiency of the injected beam was improved to 90%–95% from 70%–75% in the case of the previous compensation by the grounded grid aperture displacement. The injected beam power was increased to 3.5 MW with an energy of 165 keV using one injector. To improve beam uniformity of the large area beam, individual arc currents through filaments are controlled for uniform plasma production, with ind...

A new multi-cusp H− ion source using a localized virtual magnetic filter of type I in the plasma electrode is investigated. A multi-pole arrangement with a spacing of 10 mm of the magnet bars holds an extraction hole, optimizing the efficient production of high H− current, and at the same time only a small electron component was co-extracted with the H− ions. The local filter arrangement separates the beam electrons at a low energy. It is shown that the coextracted total electron current is determined principally by the integrated magnetic field flux (Gcm) of the local filter with an extraction system at a constant extraction voltage. When the value of the Gcm is increased, the total electron component is reduced, while the H− electrical efficiency had a broad maximum around the optimized value of the Gcm. A thicker plasma electrode should be necessary for sufficient reduction of electron current. In pure hydrogen operation, the achieved current density of H− is 10 mA/cm2. When Cs is seeded in a filter op...

Cesium recovery from the polluted layers in the 1/3 scale hydrogen negative ion source for LHD-NBI system has tested. It was found that the cesium recovery can be produced by additional discharges as from the cesium layer, aged by tungsten and residual gas, so as from the cesium layers, polluted by an occasional water leak. The highest cesium recovery to negative ion production was produced by a xenon arc, while glow discharge and arcing in hydrogen were less effective. The mechanism of recovery is the ejection of cesium from the underlying enriched layer by the arc and its transport to the surface.

Two large helical device–neutral beam injector (LHD–NBI) ion sources were fabricated and tested in the test stand for producing a beam of 180 keV×40 A with H− ions. They are Cesiated multicusp ion sources with a rectangular discharge chamber and a single stage multihole accelerator. These are scaled up from the 16 A H− ion sources in the National Institute for Fusion Science (NIFS). A plasma source with a high aspect ratio was operated stably with an arc power up to ∼300 kW for 10 s, after balancing of the electron emission from the filaments was made. A satisfactorily dense and uniform plasma without mode flip was produced. Electrons accompanied by H− ions were reduced by an extraction grid with the electron trap, instead of straight holes. The electron beam component caused by the stripping of electrons from H− ions was detected with an array of calorimeters at the bottom of the connecting duct. At the first stage of the test, one of the five segment grids of the accelerator was installed. An H− ion cur...

A large hydrogen negative-ion source was constructed as a prototype one for the negative-ion-based neutral beam injection (NBI) system in large helical device. The ion source is designed to produce 180 keV-40 A of the negative ion beam with a current density of 40 mA/cm2, and is a cesium-seeded volume production source characterized by the external magnetic filter. The arc chamber of multicusp bucket is rectangular of 35 cm×145 cm in cross section and 21 cm in depth. The accelerator is a three-grid single-stage one, and the total grid area is 25 cm×125 cm, which is divided into five sections. The ion source was installed on the negative-ion-based NBI test-stand, and using one section of the grid 5.5 A of the negative-ion beam was produced at a gas pressure of 1.8 mTorr corresponding to a current density of 27.5 mA/cm2. The extracted electron current is low of 50% of the negative ion current, and the acceleration efficiency, defined as the negative ion current divided by the acceleration drain current, is ...

A large vacuum‐immersed H− ion source has been operated on the negative‐ion‐based neutral beam teststand. The achieved level of the beam and the pulse duration in beam conditioning were limited by a high‐voltage breakdown in the vacuum vessel. A baffle plate at grounded potential for shielding completely from the charged particles was successful. A beam with an energy of up to 102 keV and the H− ion current of 0.55 A were achieved for 0.29 s without the breakdown. The ion current of ∼1.5 A was accelerated in cesium‐seeded operation. The corresponding ion current density was ∼7 mA/cm2. A magnetic filter (as Type I LV magnetic filter) on the plasma electrode was applied. The electron beam component which was extracted from the plasma source together with H− ions was found to be very reduced.

A large hydrogen negative‐ion source with an external magnetic filter has been developed for a neutral beam injection (NBI) system in the Large Helical Device (LHD), and a high‐energy and high‐current H− ion beam has been produced. The ion source is operated at a high arc efficiency of 0.1 A/kW at an operational gas pressure of less than 3.5 mTorr, and produces 47 keV–16.2 A of a H− ion beam from a grid area of 25 cm×50 cm. With two‐stage acceleration, 13.6 A of a H− ion beam has been successfully accelerated to 125 keV. Multibeamlet focusing by the aperture displacement technique has been achieved 11.2 m downstream with a gross divergence angle of 9 mrad. The alternate beamlet deflection by the magnetic field at the extraction grid, which results in beam broadening in the deflection direction, was well compensated also by the aperture displacement technique. These results satisfy the specification of the negative‐ion‐based LHD–NBI system.

Electron density measurements of a large-scaled negative ion source were carried out with a surface wave probe. By comparison of the electron densities determined with the surface wave probe and a Langmuir probe, it was confirmed that the surface wave probe is highly available for diagnostic of the electron density in H(-) ion sources. In addition, it was found that the ratio of the electron density to the H(-) ion density dramatically decreases with increase of a bias voltage and the H(-) ions become dominant negative particles at the bias voltage of more than 6 V.

We report on the characteristics of the electronegative plasma in a large-scale hydrogen negative ion (H(-)) source. The measurement has been made with a time-resolved Langmuir probe installed in the beam extraction region. The H(-) density is monitored with a cavity ring-down system to identify the electrons in the negative charges. The electron-saturation current decreases rapidly after starting to seed Cs, and ion-ion plasma is observed in the extraction region. The H(-) density steps down during the beam extraction and the electron density jumps up correspondingly. The time integral of the decreasing H(-) charge density agrees well with the electron charge collected with the probe. The agreement of the charges is interpreted to indicate that the H(-) density decreasing at the beam extraction is compensated by the electrons diffusing from the driver region. In the plasmas with very low electron density, the pre-sheath of the extraction field penetrates deeply inside the plasmas. That is because the shielding length in those plasmas is longer than that in the usual electron-ion plasmas, and furthermore the electrons are suppressed to diffuse to the extraction region due to the strong magnetic field.

Characteristics of multibeamlets are investigated by means of beamlet monitoring technique. The beamlets are extracted from an accelerator with multislot grounded grid and the profiles are observed as infrared images of temperature distributions on a cold isostatic pressed graphite plate exposed by H-beamlets. The optimal horizontal and vertical divergence angles of single beamlet are estimated at 4.1 and 6.1 mrad, respectively.

The beam profiles, port-through, rates and injection powers obtained with an improved accelerator with the multislot grounded grid are described. The accelerator has a combination of a steering grid with racetrack shaped aperture and multislot grounded grid to improve the beam optics. The optimal beam optics is obtained at the voltage ratio of 16.5-16.8, and the profiles are well fit by superposing multibeamlets with the divergent angles of 5.0 and 7.2 mrad along the direction parallel to the long and short axes of the slots of grounded grid. By adopting the racetrack shaped steering grid, the port-through rate increases from 34% to 38%, and the maximum injection power reaches 6 MW/187 keV.

A multiantenna rf ion source is studied. The new antenna system is developed to reduce the rf voltage on the antenna compared to that of the conventional loop antenna, which can reduce high voltage rf breakdown on antennas. The antenna was installed in a 1/6 scale ion source for the neutral beam injector (NBI) (H−) used in large helical devices. The characteristics of the ion density current of the plasma produced by using the segmented antennas were studied. A dense plasma with ion saturation current density of 92 mA/cm2 was generated at 45 kW of rf power at 9 MHz for the two-antenna system. At around 10 kW of rf power the plasma density jumped and became a high density mode. The threshold power for the density jump seems to be shifted by the antenna segments and the rf frequency. The current density of the positive ion beam with a small accelerator voltage is 26 mA/cm2 for 10.3 keV of extraction energy, 45 kW of rf power, and 0.16 Pa of plasma source pressure of hydrogen. This multiantenna rf source cou...

The velocity spectra of the negative-ion-(H−) based neutral beams are studied in high-performance large-area ion sources during injection into large helical device fusion plasmas. We are conducting systematic observations in standard neutral beam injection to correlate beam spectra with source operating conditions. Almost all of the transmitted beam power was at full acceleration energy (∼170keV). The small stripping beam component which was produced in the extraction gap was evaluated to be about 9%–22% by amplitude of the measured spectra for the sources in beam lines 1 and 2. H− production uniformity from the spectrum profile was 86%–90% for three sources. For the longest pulse injection during 74 and 128 s, a full energy component tended to decrease with time, while the accelerator gap stripping tail tended to increase slightly with time, which is attributed to beam-induced outgassing in the accelerator. A higher conductance multislot ground grid accelerator appeared to show little growth in the accel...

A new multiantenna system for large area radio-frequency H− ion source using a filamentless ion source was tested to extract ions from dense plasmas with high rf input power. A 1∕6 scale large helical device ion source was equipped inside a plasma chamber with four linear antenna rods. Positive-ion extraction with a single hole extractor was studied in detail, while a negative one only showed preliminary results. The positive-ion current density of 34mA∕cm2 to the collector plate was achieved with a new multiantenna after optimization of the antenna number and source gas pressure, where the number of the antennae was 2 with ∼36kW of rf input power and with a gas pressure of ∼0.1Pa with H2. If the external magnetic filter optimized for negative-ion production in the multifilament discharge source is taken off, the current density is estimated to reach about 120mA∕cm2. This corresponded closely to the value measured with a Langmuir probe near the center. Two antennae appear to be required to generate unifor...