Search

• A new method of defining the velocity field in the coolant inlet is used to quantitatively investigate the effects of the coolant swirl intensity on the film cooling performance in the operating conditions of h series turbine vanes. • The critical value of the coolant vorticity to the transformation of film coverage is 20,000 /s. • When the coolant vorticity is 40,000 /s, the area-averaged film cooling effectiveness at the near field downstream of the film hole is 54 % higher than the non-swirling case. • With high blowing ratios and large vorticities, a stable flow field is formed, where the additional coolant vortex and induced vortex appear. • For high blowing ratios, with the increase of the vorticity, the momentum advantage of the coolant gradually transforms into the effectiveness advantage. Advanced H/J series heavy-duty gas turbines are widely equipped with film cooling to protect turbine blades. Previous studies have shown that coolant swirl has an important influence on film cooling performance. However, there are few studies on the quantitative analysis of the coolant swirl intensity because of the swirl generated by the specific structure, and most of the research was carried out at relatively low temperatures. In this paper, a new method of defining the velocity field in the coolant inlet is used to quantitatively investigate the coolant swirl intensity. A numerical study of the film cooling performance for the coolant jet with various swirl intensities is conducted in the operating conditions of H series turbine vanes. The effects of the blowing ratio and coolant vorticity on the vortex structure and mixing process of the flow field are investigated emphatically, and the mechanisms for the variation of the film cooling effectiveness are analyzed. The results show that the film cooling effectiveness is greatly improved with the swirling coolant jet at high blowing ratios. When Ω n =40,000 /s, the area-averaged (L = 5 D) film cooling effectiveness is 54 % higher than the non-swirling case. Ω n =20,000 /s is a critical value of the coolant vorticity. When Ω n >20,000 /s, the film coverage transforms significantly. Furthermore, the main vortical structures in a typical SJICF flow field with high blowing ratios and large vorticities are proposed. Compared with the non-swirling JICF, the additional coolant vortex and induced vortex appear in the SJICF. Under the influence of the two vortices, the coolant momentum is sacrificed for enhanced attachment to the wall resulting in the momentum advantage gradually transforming into the effectiveness advantage with the increase of the vorticity. [ABSTRACT FROM AUTHOR]

In this paper, a new multifunctional compound, 1,1′-(oxalylbis(4,1-phenylene))bis(1H-pyrrole-2,5-dione) (BVM), is grafted onto crosslinked polyethylene (XLPE) by radical-initiated grafting to play triple roles as a voltage stabilizer, space-charge inhibitor and crosslinking auxiliary and to achieve the purpose of comprehensively enhancing the DC dielectric properties of polymers while decreasing the type and number of additives. By analyzing the DC breakdown field strength, current density and space-charge distribution of the materials at different temperatures, it is demonstrated that BVM grafting can comprehensively and effectively enhance the electrical properties of the materials, with little dependence on temperature. The BVM molecule has two polar groups and an effective molecular structure that acts as a voltage stabilizer, thus enabling the introduction of dense, uniform, deeply trapped energy levels within the material to inhibit the space charge and to capture high-energy electrons to prevent damage to the material structure; however, the two functions do not affect each other. This is also consistent with first-principles calculations and quantum-chemical calculations. Gel content testing shows no effect on polymer crosslinking, even with a 27.8% reduction in the amount of the crosslinking agent di-isopropyl peroxide (DCP), which reduces the damage to the polymer's electrical resistance caused by the byproducts of DCP decomposition. Therefore, grafting multifunctional BVM compounds to improve the dielectric characteristics of polymers is a viable area of study in the development of high-voltage direct current (HVDC) cable materials. [ABSTRACT FROM AUTHOR]

Modern gas turbines use high-performance ribs to improve internal cooling performance. In this study, the aerothermal performance of a bio-inspired truncated rib arrangement with stepped length and height variations, proposed in our previous work, is systematically studied using the numerical simulation method and the rib structures are optimized using the response surface methodology. A square channel model is employed to simulate the flow of actual turbine blade, and the rhombus-patterned ribs are placed on the two channel sidewalls. The studied structural parameters include the length variation rate, height variation rate, and pitch distance. It is found that as the rib height decreases, heat transfer is enhanced while the pressure drop is decreased. In general, however, as the variation rates of height and length increase, both the heat transfer coefficient and flow loss increase. The correlations between the thermal performance factor and the three structural parameters are obtained from thirteen cases of aerothermal performance analysis, and the optimal structure of rhombus-patterned ribs is further obtained: Δ l / l 1 = 0.333, Δ e / e 1 = 0.167, and p / e 1 = 2.000. The geometric layout optimization of the novel ribs is important for providing higher thermal performance of the internal channel and hence efficient cooling of the turbine blades. • Rhombus-patterned rib structures are optimized to enhance turbine blade aerothermal performance. • The response surface methodology is used for optimizing the structural parameters. • The optimized parameters include length variation rate, height variation rate, and pitch distance. • The relationship between the thermal performance factor and these parameters are correlated. • The rhombus-patterned ribs are also suitable for application in many heat exchange devices. [ABSTRACT FROM AUTHOR]