Search

With the increasing deployment of renewable energy resources, the scale of DC networks and renewable capacity continues to grow. System security is challenged by the decrease in inertia from traditional synchronous generators. In order to accommodate high‐penetration renewable energy, voltage stability should be considered in the renewable energy integration planning. Herein, first, a voltage stability‐constrained minimum startup index and algorithm for conventional thermal power plants are proposed. Then, based on time series production simulation, a renewable energy integration capacity analysis algorithm is designed considering voltage stability and peak shaving constraints. Finally, based on the boundary conditions of the "Fifteen‐Five Plan", the renewable energy capacity considering voltage stability and peak shaving constraints for Northwest and East China power grids are analysed to verify the effectiveness and engineering practicality of the proposed methodology. The results demonstrate that the proposed method can maintain the renewable energy integration goal outlined in the "Fifteen‐Five Plan" while maintaining the voltage stability in these regions. [ABSTRACT FROM AUTHOR]

A new integration strategy of grid‐forming‐controlled wind farms connected to the bulk power systems through high‐voltage direct current transmission based on the modular multi‐level converter (MMC) is proposed to solve the problem of traditional uncontrollable DC overvoltage during the short circuit faults at the receiving end. However, a new DC overvoltage phenomenon appears after the fault is cleared, and the interaction between the wind farm and sending‐ and receiving‐end MMCs makes the DC overvoltage mechanism more complex; further exploration shows that DC overvoltage during the sending‐end fault recovery stage occurs under the new integration strategy. Therefore, the evolution process and mechanism of the new DC overvoltage are analysed. It is found that affected by the interaction between wind farms and MMCs, the alternate saturation of the integrators in the PI controller of MMCs is the main cause. Based on this understanding, additional controls are proposed to suppress this DC overvoltage during the fault recovery stage. Simulations are carried out on a test with MATLAB/Simulink, and the results verify the efficacy of the proposed methods in suppressing DC overvoltage. [ABSTRACT FROM AUTHOR]

The active distribution network (ADN) can obtain measurement data, estimate system states, and control distributed energy resources (DERs) and flexible loads to ensure voltage stability. However, the ADN is more vulnerable to cyber attacks due to the recent wave of digitization and automation efforts. In this article, false data injection (FDI) attacks are focused on and they are classified into two types, that is, type I attacks on measurement data and type II attacks on control commands. After studying the impact of these two FDI attacks on the ADN, a new threat is revealed called coordinated FDI attack, which can maximize the voltage deviation by coordinating type I and type II FDI attacks. From the attacker's perspective, the scheme of CFDI is proposed and an algorithm is developed to find the optimal attack strategy. The feasibility of CFDI attacks has been validated on a smart distribution testbed. Moreover, simulation results on an ADN benchmark have demonstrated that CFDI attacks could cause remarkable voltage deviation that may deteriorate the stability of the distribution network. Moreover, the impact of CFDI attacks is higher than pure type I or type II attacks. To mitigate the threat, some countermeasures against CFDI attacks are also proposed. [ABSTRACT FROM AUTHOR]

Copyright of Przegląd Elektrotechniczny is the property of Przeglad Elektrotechniczny and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Abstract A new integration strategy of grid‐forming‐controlled wind farms connected to the bulk power systems through high‐voltage direct current transmission based on the modular multi‐level converter (MMC) is proposed to solve the problem of traditional uncontrollable DC overvoltage during the short circuit faults at the receiving end. However, a new DC overvoltage phenomenon appears after the fault is cleared, and the interaction between the wind farm and sending‐ and receiving‐end MMCs makes the DC overvoltage mechanism more complex; further exploration shows that DC overvoltage during the sending‐end fault recovery stage occurs under the new integration strategy. Therefore, the evolution process and mechanism of the new DC overvoltage are analysed. It is found that affected by the interaction between wind farms and MMCs, the alternate saturation of the integrators in the PI controller of MMCs is the main cause. Based on this understanding, additional controls are proposed to suppress this DC overvoltage during the fault recovery stage. Simulations are carried out on a test with MATLAB/Simulink, and the results verify the efficacy of the proposed methods in suppressing DC overvoltage.

Abstract With the increasing deployment of renewable energy resources, the scale of DC networks and renewable capacity continues to grow. System security is challenged by the decrease in inertia from traditional synchronous generators. In order to accommodate high‐penetration renewable energy, voltage stability should be considered in the renewable energy integration planning. Herein, first, a voltage stability‐constrained minimum startup index and algorithm for conventional thermal power plants are proposed. Then, based on time series production simulation, a renewable energy integration capacity analysis algorithm is designed considering voltage stability and peak shaving constraints. Finally, based on the boundary conditions of the “Fifteen‐Five Plan”, the renewable energy capacity considering voltage stability and peak shaving constraints for Northwest and East China power grids are analysed to verify the effectiveness and engineering practicality of the proposed methodology. The results demonstrate that the proposed method can maintain the renewable energy integration goal outlined in the “Fifteen‐Five Plan” while maintaining the voltage stability in these regions.

Abstract The active distribution network (ADN) can obtain measurement data, estimate system states, and control distributed energy resources (DERs) and flexible loads to ensure voltage stability. However, the ADN is more vulnerable to cyber attacks due to the recent wave of digitization and automation efforts. In this article, false data injection (FDI) attacks are focused on and they are classified into two types, that is, type I attacks on measurement data and type II attacks on control commands. After studying the impact of these two FDI attacks on the ADN, a new threat is revealed called coordinated FDI attack, which can maximize the voltage deviation by coordinating type I and type II FDI attacks. From the attacker's perspective, the scheme of CFDI is proposed and an algorithm is developed to find the optimal attack strategy. The feasibility of CFDI attacks has been validated on a smart distribution testbed. Moreover, simulation results on an ADN benchmark have demonstrated that CFDI attacks could cause remarkable voltage deviation that may deteriorate the stability of the distribution network. Moreover, the impact of CFDI attacks is higher than pure type I or type II attacks. To mitigate the threat, some countermeasures against CFDI attacks are also proposed.

Abstract The worldwide occurrence of wind droughts challenges the balance of power systems between energy production and consumption. Expanding inter‐day energy storage serves as a strategic solution, yet optimizing its capacity depends on accurately modeling future renewable energy uncertainties to avoid over‐ or under‐investment. Existing approaches that use the historical extreme scenario set (HESS) to represent future conditions are contentious due to potential inadequacies in forecasting future extreme scenarios (ESs), including those on a decadal or centennial scale. This study addresses the issue by proposing an advanced energy storage expansion framework that leverages Extreme Value Theory (EVT) and a novel Deep Generative Model, namely the Diffusion Model. To model the extremes in a principled way, this work leverages EVT to establish a severity‐probability mapping for wind droughts, guiding the training process of the Diffusion Model. This model excels in generating ESs that accurately reflect the distribution of real‐world extremes, thereby significantly enhancing the predictive capacity of HESS. Case studies on a real‐world power system confirm the method's capacity to generate high‐quality ESs, encompassing the most severe historical wind droughts not included in the training dataset, thereby facilitating resilient energy storage expansion against unforeseen extremes.

Abstract In modern power systems, the uncertainty and volatility of generation and loads greatly increase the balance discrepancy between the power supply and demand, creating major potential security hazards. To limit out‐of‐bound frequencies, an effective frequency control method for power systems with interval uncertain disturbances is proposed. Based on the state space model of the system frequency response with delays, linear matrix inequalities are constructed based on the input‒output finite‐time stability of the system frequency. By searching for the output feedback gain and altering the time delay with the Padé approximation, the feasibility of the linear matrix inequalities is improved, and a frequency controller is designed. The simulation results show that the proposed method can effectively control frequency deviations. When the closed‐loop system is disturbed by uncertain power fluctuations, its frequency will always remain within the allowable range to ensure the secure operation of the power system.

Abstract Numerous strategies have been proposed for the detection and prevention of non‐technical electricity losses due to fraudulent activities. Among these, machine learning algorithms and data‐driven techniques have gained prominence over traditional methodologies due to their superior performance, leading to a trend of increasing adoption in recent years. A novel two‐step process is presented for detecting fraudulent Non‐technical losses (NTLs) in smart grids. The first step involves transforming the time‐series data with additional extracted features derived from the publicly available State Grid Corporation of China (SGCC) dataset. The features are extracted after identifying abrupt changes in electricity consumption patterns using the sum of finite differences, the Auto‐Regressive Integrated Moving Average model, and the Holt‐Winters model. Following this, five distinct classification models are used to train and evaluate a fraud detection model using the SGCC dataset. The evaluation results indicate that the most effective model among the five is the Gradient Boosting Machine. This two‐step approach enables the classification models to surpass previously reported high‐performing methods in terms of accuracy, F1‐score, and other relevant metrics for non‐technical loss detection.

Abstract In recent years, frequent occurrence of extreme weather events has caused great losses to the power system. Meanwhile, the high penetration of renewable energy has brought new challenges to the safe operation of the system. Coordination of various measures against different stages of disaster can effectively reduce the overall loss and enhance system's resilience. This paper proposed a methodology to coordinate preventive and emergency dispatch stages based on the defender–attacker–defender model, in which various dispatching measures are modelled as defenders, whereas the extreme weather event and wind power's uncertainty are modelled as attackers. Specifically, a two‐stage three‐layer robust optimal dispatching model is established, in which conventional generator's output, wind farm's grid‐connected planning, and load shedding are taken as the main dispatching measures. To solve this model, the column and constraint generation algorithm is used to transform the three‐layer optimization model into a mixed integer linear problem . The effectiveness of the proposed model is verified in the modified IEEE RTS‐79 test system, and the results show that the coordination of preventive and emergency dispatch can effectively reduce the load outage cost under extreme weather, thus enhancing the ability of power system to cope with extreme scenarios.

The worldwide occurrence of wind droughts challenges the balance of power systems between energy production and consumption. Expanding inter‐day energy storage serves as a strategic solution, yet optimizing its capacity depends on accurately modeling future renewable energy uncertainties to avoid over‐ or under‐investment. Existing approaches that use the historical extreme scenario set (HESS) to represent future conditions are contentious due to potential inadequacies in forecasting future extreme scenarios (ESs), including those on a decadal or centennial scale. This study addresses the issue by proposing an advanced energy storage expansion framework that leverages Extreme Value Theory (EVT) and a novel Deep Generative Model, namely the Diffusion Model. To model the extremes in a principled way, this work leverages EVT to establish a severity‐probability mapping for wind droughts, guiding the training process of the Diffusion Model. This model excels in generating ESs that accurately reflect the distribution of real‐world extremes, thereby significantly enhancing the predictive capacity of HESS. Case studies on a real‐world power system confirm the method's capacity to generate high‐quality ESs, encompassing the most severe historical wind droughts not included in the training dataset, thereby facilitating resilient energy storage expansion against unforeseen extremes. [ABSTRACT FROM AUTHOR]

In today's highly advanced information technology environment, modern network and communication technologies are widely used in monitoring and controlling power systems. These technologies have evolved significantly. They now form a high-performance digital system known as the cyber–physical power system. However, vulnerabilities in communication networks present growing threats to these systems. This paper seeks to enhance the accurate assessment of the security posture of cyber-physical power systems by inferring attackers' intentions. A threat modeling approach based on Bayesian attack graphs is presented, employing Bayesian networks to define and evaluate potential threats that attackers could pose to different system infrastructures. The paper initially conducts a qualitative analysis of the system's threats, constructing a directed graph structure and establishing conditional probability tables among nodes based on prior knowledge. Subsequently, methods are developed to compute the threat levels at different system nodes using real-time detected attack events. Further analysis methods and security assessment metrics are also developed to identify attack paths and quantify system security. Finally, a Bayesian attack graph is constructed in accordance with the system's structure. In practical scenarios, the attack path analysis method can predict the most vulnerable attack paths, while the absolute values of the security assessment metrics indicate the overall risk level of the system. [ABSTRACT FROM AUTHOR]

Recently, deep learning (DL) based dynamic security assessment (DSA) methods have been very successful. However, although a DSA model can be trained well for a specific topology, it often does not perform well for other topologies. Since the topology in real‐world power systems is frequently changing, the performance reduction of DL‐based DSA methods is very serious, which is a challenging and urgent problem. This paper proposes a novel DSA method based on a convolutional neural network (CNN) to solve this problem. In the proposed method, a strong yet simple domain adaptation approach named adaptive batch normalization (AdaBN) is used, which significantly enhances the extensibility and generalizability of the DSA model when the topology changes and eliminates the need to train a large number of models. This approach achieves a deep adaptation effect by modulating the statistics from the source domain to the target domain in all batch normalization layers across the model. Unlike other domain adaptation methods, this method is parameter‐free, requires no additional components, and has advanced performance despite its simplicity. In addition, this paper introduces TGAN‐based data augmentation to deal with the difficulty of costly data collection and labelling. This data augmentation makes the proposed model applicable to small databases. The test results of the proposed method on IEEE 39‐bus and IEEE 118‐bus systems show that this method can evaluate system dynamic security during topology changes and in the face of data noise with high accuracy. [ABSTRACT FROM AUTHOR]

In modern power systems, the uncertainty and volatility of generation and loads greatly increase the balance discrepancy between the power supply and demand, creating major potential security hazards. To limit out‐of‐bound frequencies, an effective frequency control method for power systems with interval uncertain disturbances is proposed. Based on the state space model of the system frequency response with delays, linear matrix inequalities are constructed based on the input‒output finite‐time stability of the system frequency. By searching for the output feedback gain and altering the time delay with the Padé approximation, the feasibility of the linear matrix inequalities is improved, and a frequency controller is designed. The simulation results show that the proposed method can effectively control frequency deviations. When the closed‐loop system is disturbed by uncertain power fluctuations, its frequency will always remain within the allowable range to ensure the secure operation of the power system. [ABSTRACT FROM AUTHOR]

The generation rescheduling is described as the power generation shifting from one or more generators to one or more other generators as a preventive action to improve and maintain the security of the power system. Since, there is a direct link between security improvement and the lines overload under contingencies, by rescheduling generation, the transmission lines become more flexible and thus, the overload can be relieved. In this paper, contingency constrained optimal power flow (CCOPF) problem based on generation rescheduling by considering the uncertainty of photovoltaic (PV), wind turbine (WT), and plug-in hybrid electric vehicle (PHEV) have been addressed. Water cycle algorithm (WCA) using its potential in finding optimal solution has been used in order to reschedule the generators and optimize the total fuel cost, power losses under contingency scenario, and system security. Moreover, stochastic approach has been proposed for taking into account the uncertainty of PV, WT, and PHEV. Overall performance index including the power and the voltage severity indices have been provided for determining overloaded transmission lines due to the lines' outage and consequently elimination of overloaded lines. The efficiency of the proposed algorithm has been evaluated on two IEEE-30 and IEEE 118-bus systems. The results are compared with the results of other classical and metaheuristic optimization algorithms. The simulations reveal that the WCA outperforms the other reported optimizers, and is more efficient and effective in improving security for power systems. In addition, the obtained numerical results show that renewable energy sources can significantly reduce fuel costs. [ABSTRACT FROM AUTHOR]

In recent years, frequent occurrence of extreme weather events has caused great losses to the power system. Meanwhile, the high penetration of renewable energy has brought new challenges to the safe operation of the system. Coordination of various measures against different stages of disaster can effectively reduce the overall loss and enhance system's resilience. This paper proposed a methodology to coordinate preventive and emergency dispatch stages based on the defender–attacker–defender model, in which various dispatching measures are modelled as defenders, whereas the extreme weather event and wind power's uncertainty are modelled as attackers. Specifically, a two‐stage three‐layer robust optimal dispatching model is established, in which conventional generator's output, wind farm's grid‐connected planning, and load shedding are taken as the main dispatching measures. To solve this model, the column and constraint generation algorithm is used to transform the three‐layer optimization model into a mixed integer linear problem. The effectiveness of the proposed model is verified in the modified IEEE RTS‐79 test system, and the results show that the coordination of preventive and emergency dispatch can effectively reduce the load outage cost under extreme weather, thus enhancing the ability of power system to cope with extreme scenarios. [ABSTRACT FROM AUTHOR]

Cyber–physical distribution systems with renewable energy should have high resilience under extreme conditions. However, in a distribution system with deep cyber–physical coupling, the propagation of information risk impairs the resilience of the system. This paper proposes a strategy to improve the resilience of cyber–physical distribution systems that considers cross‐space propagation of information risk. First, the mechanism for interaction between the cyber space and physical space is analyzed, and an information risk cross‐space propagation model is proposed. Second, the risk status of key device nodes is quantified according to the risk propagation model, and an optimization strategy for information risk control is obtained, whose objective function is the minimum risk of the coupling network. Third, a fault restoration strategy that considers cyber space risk is proposed. Finally, the paper reports experiments using the modified IEEE 33‐node and 123‐node distribution networks to simulate the proposed strategy and verify its effectiveness. [ABSTRACT FROM AUTHOR]

Abstract The rapid growth of offshore wind power has resulted in a mismatch between generation and demand because of its variability. To quantify the maximum wind power penetration of the transmission network, the dispatchable region is defined as the largest region in the uncertainty space. The security distance is defined as the minimum distance from the operating point to the boundaries of the dispatchable region. System operators can use security distance as a metric to assess the flexibility of the power system. This paper proposes a method to construct the dispatchable region for the AC/DC hybrid system with VSC‐HVDC by outer convex relaxation firstly. The second‐order cone relaxation is employed to reformulate non‐convex and non‐linear power flow equations. Next, a polyhedral approximation is adopted to obtain the convex hull of the dispatchable region. Subsequently, an efficient algorithm known as adaptive constraint generation (Ad‐CG) is introduced to calculate the boundaries of the dispatchable region. Furthermore, solving the Chebyshev centre problem determines the minimal security distance. The modified IEEE 5‐bus and 39‐bus system is used for validating effectiveness of the proposed method and evaluating the impact of the converter reactive power compensation capacity and generation dispatch on the dispatchable region.

Abstract High penetrations of renewable energy are crucial for low‐carbon power systems. However, the higher volatility of renewable power generation pushes real‐time operations closer to equipment limits. It is thus important to utilize flexibilities in the system through corrective security‐constrained economic dispatch (SCED) that allows generators to take corrective adjustments after contingencies. The corrective SCED problem, containing a large number of contingencies, and corresponding post‐contingency decisions and constraints, is very large in scale and difficult to solve using purely model‐based methods within the strict time limits of real‐time markets. To accelerate the solution process, this paper develops a novel interpretable data‐driven contingency classification method. Historical data and their potentially useful patterns are utilized in interpretable data‐driven decision tree classifiers. To directly consider continuous features, such as net load values, and to consider imbalanced datasets without much additional complexity, Improved Strong Optimal Classification Trees (ISOCTs) are developed with new branching threshold constraints and category weights in the objective function. ISOCTs are then embedded into a hybrid model‐based and data‐driven framework to guarantee the accuracy of the real‐time active contingency set and the resulting security of dispatch decisions. Numerical testing results demonstrate the classification accuracy, computational efficiency, and interpretability of the proposed approach.

Abstract Traditional power systems have evolved into cyber‐physical power systems (CPPS) with the integration of information and communication technologies. CPPS can be considered as a typical hierarchical control system that can be divided into two parts: the power grid and the communication network. CPPS will face new vulnerabilities which can have network contingencies and cascading consequences. To address this challenge, a virtual‐physical power flow (VPPF) method is proposed for the vulnerability assessment of CPPS. The proposed method contains dual power flows, one is to simulate a virtual power flow from decision‐making units, and the other is to simulate a physical power flow. In addition, a novel hierarchical control model is proposed that includes four layers of CPPS: the physical layer, the secondary device layer, the regional control layer, and the national control layer. The model is based on IEEE test cases using data and structures provided by MATPOWER. Denial‐of‐service (DoS) and false data injection (FDI) are simulated as two major cyber‐attacks in CPPS. A novel vulnerability index is proposed that consists of system voltage, network latency, and node betweenness as three key indicators. This is a comprehensive and adaptive index because it encompasses both cyber and physical system characteristics and can be applied to several types of cyber‐attacks. The results of the vulnerability assessment are compared in national and regional control structures of CPPS to evaluate the vulnerability of cyber‐physical nodes.

The rapid growth of offshore wind power has resulted in a mismatch between generation and demand because of its variability. To quantify the maximum wind power penetration of the transmission network, the dispatchable region is defined as the largest region in the uncertainty space. The security distance is defined as the minimum distance from the operating point to the boundaries of the dispatchable region. System operators can use security distance as a metric to assess the flexibility of the power system. This paper proposes a method to construct the dispatchable region for the AC/DC hybrid system with VSC‐HVDC by outer convex relaxation firstly. The second‐order cone relaxation is employed to reformulate non‐convex and non‐linear power flow equations. Next, a polyhedral approximation is adopted to obtain the convex hull of the dispatchable region. Subsequently, an efficient algorithm known as adaptive constraint generation (Ad‐CG) is introduced to calculate the boundaries of the dispatchable region. Furthermore, solving the Chebyshev centre problem determines the minimal security distance. The modified IEEE 5‐bus and 39‐bus system is used for validating effectiveness of the proposed method and evaluating the impact of the converter reactive power compensation capacity and generation dispatch on the dispatchable region. [ABSTRACT FROM AUTHOR]

High penetrations of renewable energy are crucial for low‐carbon power systems. However, the higher volatility of renewable power generation pushes real‐time operations closer to equipment limits. It is thus important to utilize flexibilities in the system through corrective security‐constrained economic dispatch (SCED) that allows generators to take corrective adjustments after contingencies. The corrective SCED problem, containing a large number of contingencies, and corresponding post‐contingency decisions and constraints, is very large in scale and difficult to solve using purely model‐based methods within the strict time limits of real‐time markets. To accelerate the solution process, this paper develops a novel interpretable data‐driven contingency classification method. Historical data and their potentially useful patterns are utilized in interpretable data‐driven decision tree classifiers. To directly consider continuous features, such as net load values, and to consider imbalanced datasets without much additional complexity, Improved Strong Optimal Classification Trees (ISOCTs) are developed with new branching threshold constraints and category weights in the objective function. ISOCTs are then embedded into a hybrid model‐based and data‐driven framework to guarantee the accuracy of the real‐time active contingency set and the resulting security of dispatch decisions. Numerical testing results demonstrate the classification accuracy, computational efficiency, and interpretability of the proposed approach. [ABSTRACT FROM AUTHOR]

Abstract Recently, deep learning (DL) based dynamic security assessment (DSA) methods have been very successful. However, although a DSA model can be trained well for a specific topology, it often does not perform well for other topologies. Since the topology in real‐world power systems is frequently changing, the performance reduction of DL‐based DSA methods is very serious, which is a challenging and urgent problem. This paper proposes a novel DSA method based on a convolutional neural network (CNN) to solve this problem. In the proposed method, a strong yet simple domain adaptation approach named adaptive batch normalization (AdaBN) is used, which significantly enhances the extensibility and generalizability of the DSA model when the topology changes and eliminates the need to train a large number of models. This approach achieves a deep adaptation effect by modulating the statistics from the source domain to the target domain in all batch normalization layers across the model. Unlike other domain adaptation methods, this method is parameter‐free, requires no additional components, and has advanced performance despite its simplicity. In addition, this paper introduces TGAN‐based data augmentation to deal with the difficulty of costly data collection and labelling. This data augmentation makes the proposed model applicable to small databases. The test results of the proposed method on IEEE 39‐bus and IEEE 118‐bus systems show that this method can evaluate system dynamic security during topology changes and in the face of data noise with high accuracy.

Abstract In electrical power systems, FACTS devices effectively control power flow and change bus voltages, leading to lower system losses and excellent system stability. The article discusses the research from the last decade that evaluated various methods for placing FACTS devices using the meta-heuristic approach to address the positioning of FACTS devices to maintain proper bus voltages and control line flow and improve the overall system efficiency. The need for more efficient electricity systems management has given rise to innovative technologies in power generation and transmission. The combined cycle power station is a good example of a new development in power generation and flexible AC transmission systems, generally known as FACTS, are controllers that improve transmission systems. Worldwide transmission systems are undergoing continuous changes and restructuring. They are becoming more heavily loaded and are being operated in ways not originally envisioned. Transmission systems must be flexible to react to more diverse generation and load patterns. In addition, the economical utilization of transmission system assets is of vital importance to enable utilities in industrialized countries to remain competitive and to survive. In developing countries, the optimized use of transmission systems investments is also important to support industry, create employment and utilize efficiently scarce economic resources. FACTS controller is a technology that responds to these needs. It significantly alters the way transmission systems are developed and controlled together with improvements in asset utilization, system flexibility and system performance. Several models and techniques suggest that devices can be placed in a particular location with different parameter settings. Finally, the optimization problem improved system performance by decreasing power loss, improving the voltage profile and power angle at each bus, raising the L-index, and minimizing generating costs. FACTS devices can increase the transmission line’s capacity for transferring power by increasing the voltage at its terminals at both ends and reducing line reactance. The FACTS controller must be installed in the distribution and transmission lines to maximize the power flow. Various techniques are used for the best placement of FACTS controllers, including analytical methods, arithmetic programming approaches, meta-heuristic optimization approaches, and hybrid approaches—this paper analyses numerous analytical and meta-heuristic optimization techniques to place FACTS controllers in the most advantageous locations. The fundamental problems in intelligent power systems, such as improving stability, power quality, and managing congestion, are discussed in this study, along with several applications of FACTS devices. The cutting-edge power systems of today provide users with constant, high-quality power through smart grids and smart meters.

In electrical power systems, FACTS devices effectively control power flow and change bus voltages, leading to lower system losses and excellent system stability. The article discusses the research from the last decade that evaluated various methods for placing FACTS devices using the meta-heuristic approach to address the positioning of FACTS devices to maintain proper bus voltages and control line flow and improve the overall system efficiency. The need for more efficient electricity systems management has given rise to innovative technologies in power generation and transmission. The combined cycle power station is a good example of a new development in power generation and flexible AC transmission systems, generally known as FACTS, are controllers that improve transmission systems. Worldwide transmission systems are undergoing continuous changes and restructuring. They are becoming more heavily loaded and are being operated in ways not originally envisioned. Transmission systems must be flexible to react to more diverse generation and load patterns. In addition, the economical utilization of transmission system assets is of vital importance to enable utilities in industrialized countries to remain competitive and to survive. In developing countries, the optimized use of transmission systems investments is also important to support industry, create employment and utilize efficiently scarce economic resources. FACTS controller is a technology that responds to these needs. It significantly alters the way transmission systems are developed and controlled together with improvements in asset utilization, system flexibility and system performance. Several models and techniques suggest that devices can be placed in a particular location with different parameter settings. Finally, the optimization problem improved system performance by decreasing power loss, improving the voltage profile and power angle at each bus, raising the L-index, and minimizing generating costs. FACTS devices can increase the transmission line's capacity for transferring power by increasing the voltage at its terminals at both ends and reducing line reactance. The FACTS controller must be installed in the distribution and transmission lines to maximize the power flow. Various techniques are used for the best placement of FACTS controllers, including analytical methods, arithmetic programming approaches, meta-heuristic optimization approaches, and hybrid approaches—this paper analyses numerous analytical and meta-heuristic optimization techniques to place FACTS controllers in the most advantageous locations. The fundamental problems in intelligent power systems, such as improving stability, power quality, and managing congestion, are discussed in this study, along with several applications of FACTS devices. The cutting-edge power systems of today provide users with constant, high-quality power through smart grids and smart meters. [ABSTRACT FROM AUTHOR]

Abstract With the introduction of dual carbon targets, clean energy is connected to the grid on a large scale, and the stochastic and volatility of its output further affects the stable operation of the new power system. Meanwhile, in order to solve the problem that it is difficult to take into account the participation of clean energy in market‐oriented trading and complete consumption in the construction of power market, the new type of power system source–load balance dispatching model considering the market of clean energy and cross‐section stabilization is proposed. Firstly, a clean energy market price competition model based on the market clearing mechanism is proposed to realize the alternative consumption of clean energy. Secondly, considering the section security of inter‐system power transmission, a new power system source‐load balance two‐level optimization model is established by considering the cross‐section power rate and real‐time trading of clean energy market. Finally, the advantages of the model in enhancing the high proportion of clean energy consumption, rationally clearing the clean energy market and reducing the cross‐section load ratio of the contact line are verified through simulation.

With the introduction of dual carbon targets, clean energy is connected to the grid on a large scale, and the stochastic and volatility of its output further affects the stable operation of the new power system. Meanwhile, in order to solve the problem that it is difficult to take into account the participation of clean energy in market‐oriented trading and complete consumption in the construction of power market, the new type of power system source–load balance dispatching model considering the market of clean energy and cross‐section stabilization is proposed. Firstly, a clean energy market price competition model based on the market clearing mechanism is proposed to realize the alternative consumption of clean energy. Secondly, considering the section security of inter‐system power transmission, a new power system source‐load balance two‐level optimization model is established by considering the cross‐section power rate and real‐time trading of clean energy market. Finally, the advantages of the model in enhancing the high proportion of clean energy consumption, rationally clearing the clean energy market and reducing the cross‐section load ratio of the contact line are verified through simulation. [ABSTRACT FROM AUTHOR]

Optimal power flow (OPF) is a tool used for minimization through that secured and cost-effective power systems is obtained with the inclusion of FACTS devices for existing power systems that enhance the power transfer ability of the power system, which reduces congestion. The current work proposed a solution to the OPF issue in power systems using genetic algorithm (GA). The proposed technique is implemented on an IEEE 30 bus system by considering the minimization of fuel cost and L-index functions. The results at the end of this paper pre-sent the efficacy of GA algorithm to solve OPF issues in power systems and FACTS devices while comparing it to other algorithms presented previous re-search.