Search

Expanded polystyrene will account for 5.3% of total global plastic production in 2021 and is widely used for food packaging due to its excellent moisture resistance and thermal insulation. However, some of these packages are often used only once before being discarded, generating large amounts of environmentally harmful plastic waste. A very attractive alternative to the conventional methods used for polymer processing is the use of supercritical carbon dioxide (scCO 2 ) since it has mass-transfer properties adapted to the foam morphology, generating different path lengths for the diffusion of active compounds within its structure and can dissolve a wide range of organic molecules under supercritical conditions. The objective of this research was to evaluate the effect of operational variables on the process of caffeic acid (CA) impregnation and subsequent foaming of polylactic acid (PLA) as well as two PLA/poly(butylene-co-terephthalate-adipate) (PBAT) blends using scCO 2 . The results showed an increase in the degree of crystallinity of the CA-impregnated samples due to the nucleation effect of the active compound. On the other hand, SEM micrographs of both films and foams showed significant differences due to the presence of PBAT and its low miscibility with PLA. Finally, the results obtained in this work contribute to the knowledge of the important parameters to consider for the implementation of the impregnation and foaming process of PLA and PLA/PBAT blends with potential use in food packaging.

In the last decade, among the emerging technologies in the area of bioplastics, additive manufacturing (AM), commonly referred to as 3D printing, stands out. This technology has gained great interest in the development of new products, mainly due to its capability to easily produce customized and low-cost plastic products. This work aims to evaluate the effect of supercritical foaming of 3D-printed parts based on a commercial PLA matrix loaded with calcium carbonate, for single-use sustainable food contact materials. 3D-printed PLA/CaCO 3 parts were obtained by 3D printing with a 20% and 80% infill, and two infill patterns, rectilinear and triangular, were set for each of the infill percentages selected. Supercritical fluid foaming of PLA/CaCO 3 composite printed parts was performed using a pressure of 25 MPa, a temperature of 130 °C for 23 min, with a fast depressurization rate (1 s). Closed-cell foams were achieved and the presence of CaCO 3 did not influence the surface of the foams or the cell walls, and no agglomerations were observed. Foam samples with 80% infill showed subtle temperature fluctuations, and thermogravimetric analysis showed that samples were thermally stable up to ~300 °C, while the maximum degradation temperature was around 365 °C. Finally, tensile test analysis showed that for lower infill contents, the foams showed lower mechanical performance, while the 80% infill and triangular pattern produced foams with good mechanical performance. These results emphasize the interest in using the supercritical CO 2 process to easily produce foams from 3D-printed parts. These materials represent a sustainable alternative for replacing non-biodegradable materials such as Expanded Polystyrene, and they are a promising option for use in many industrial applications, such as contact materials.

Compounds derived from essential oils have been used in active packaging, but their volatility and degradability negatively affect stability and leads to high release rates. The present study aimed to develop PLA bionanocomposite foams loaded with carvacrol cocrystal by supercritical CO 2 and its release into a food simulant for control release in food packaging. For this purpose, 4,4'-bipyridine was used as coformer and carvacrol as active agent. Cocrystallized closed cell foams were obtained using supercritical CO 2 and were characterized in terms of their physicochemical and mechanical properties, and release kinetics to a D1 simulant were evaluated as well as the antioxidant ability. A better overall mechanical behavior due to the nanoclay promoting a higher interfacial adhesion with the polymeric matrix was revealed. A higher incorporation of carvacrol was observed in samples with higher C30B content. The incorporated cocrystals showed a decrease of one order of magnitude in the estimated effective diffusion coefficient of carvacrol and showed antioxidant activity. These results suggest that the nanocomposite foam containing carvacrol-based cocrystals could be used in active packaging systems with controlled release characteristics, especially with highly volatile compounds, and can be proposed for other fields such as biomedical applications., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023. Published by Elsevier B.V.)