Search

Background: The anterior interosseus nerve (AIN) to ulnar motor nerve transfer has been popularized as an adjunct to surgical decompression in patients with severe cubital tunnel syndrome (CuTS) and high ulnar nerve injuries. The factors influencing its implementation in Canada have yet to be described. Methods: An electronic survey was distributed to all members of the Canadian Society of Plastic Surgery (CSPS) using REDCap software. The survey examined 4 themes: previous training/experience, practice volume of nerve pathologies, experience with nerve transfers, and approach to the treatment of CuTS and high ulnar nerve injuries. Results: A total of 49 responses were collected (12% response rate). Of all, 62% of surgeons would use an AIN to ulnar motor supercharge end-to-side (SETS) transfer for a high ulnar nerve injury. For patients with CuTS and signs of intrinsic atrophy, 75% of surgeons would add an AIN-SETS transfer to a cubital tunnel decompression. Sixty-five percent would also release Guyon's canal, and the majority (56%) use a perineurial window for their end-to-side repair. Eighteen percent of surgeons did not believe the transfer would improve outcomes, 3% cited lack of training, and 3% would preferentially use tendon transfers. Surgeons with hand fellowship training and those less than 30 years in practice were more likely to use nerve transfers in the treatment of CuTS (P <.05). Conclusions: Most CSPS members would use an AIN-SETS transfer in the treatment of both a high ulnar nerve injury and severe CuTS with intrinsic atrophy. [ABSTRACT FROM AUTHOR]

Purpose: Intramedullary (IM) screw fixation is gaining popularity in the treatment of metacarpal fractures. Despite its rapid adoption, there is a paucity of evidence regarding parameters to optimize effectiveness. This study aimed to quantify the relationship between stability, IM screw size, and canal fill using a cadaveric model., Methods: Thirty cadaveric metacarpals (14 index, 13 middle, and three ring fingers; mean age: 58.3 years, range: 48-70) were selected to allow for canal fill ratios of 0.7-1.1 for screws sized 3.0, 3.5, and 4.5 mm. Metacarpals underwent a 45° volar-dorsal osteotomy at the midpoint before fixation with an IM screw. Specimens were subjected to 100 cycles of loading at 10 N, 20 N, and 30 N before load-to-failure testing. Correlation coefficients for angular displacement on the final cycle at each load, peak load to failure, and average stiffness were assessed., Results: Correlation coefficients for the angular displacement on the 100th cycle were as follows: 10 N, R = 0.62, 20 N, R = 0.57, and 30N, R = 0.58. Correlation values for peak load to failure as a function of canal fit were as follows: 3.0 mm, R = 0.5, 3.5 mm, R = 0.17, and 4.5 mm, R = 0.44. The canal fill ratio that intersected the line-of-best fit at an angular deformity of 10° was 0.74. Average peak forces for 3.0-, 3.5-, and 4.5-mm screws were 79.5, 136.5, and 179.6 N, respectively. Average stiffness for each caliber was 14.8, 33.4, and 52.3 N/mm., Conclusions: Increasing screw diameter and IM fill resulted in more stable fixation, but marginal gains were seen in ratios >0.9. A minimum fill ratio of 0.74 was sufficient to withstand forces of early active motion with angular deformity <10°., Clinical Relevance: An understanding of the relationship of IM fill ratio of metacarpal screws to fracture stability may provide a framework for clinicians to optimally size these implants., Competing Interests: Conflicts of Interest No benefits in any form have been received or will be received related directly to this article., (Copyright © 2024 American Society for Surgery of the Hand. Published by Elsevier Inc. All rights reserved.)