Search

Plastic is a revolutionary material. However, pollution caused by plastic damages the environment, human health, and economy of different countries. It is important to find the new methods for recycling and reusing plastic materials. In this present study, plastic waste coming from high‐density polyethylene (HDPE) cups (called HDPEr in the following) are used together with virgin cork for production of composite materials. Different fractions of virgin cork with HDPEr are tested and allow to obtain successfully composite materials. The properties of HDPEr and composite are compared. The morphology of elaborated composite is studied by scanning electron microscope (SEM). The thermal properties are investigated by thermogravimetric analysis (TGA) analysis; the flammability study is performed using a cone calorimeter. Moreover, the mechanical properties of the samples stored under different conditions are studied by tensile strength experiments. The results show that the cork content has an effect on the mechanical and thermal properties. The feasibility of the composites based on cork and HDPEr wastes opens the way of reusing of these wastes. The formulation of HDPEr composites must be optimized by adding a flame retardant and a coupling agent. [ABSTRACT FROM AUTHOR]

This research studies natural rubber (NR) composite blends prepared with recycled polyethylene (PE), polyurethane waste (PU), silica (SiO2), and aluminum trihydroxide (ATH) under the proper mixing conditions using an internal mixer and a two-roll mill. The mechanical, impact, dynamic mechanical, and thermal properties, together with flammability, were investigated. NR/PU composites filled with a specific SiO2/ATH concentration resulted in excellent flame-retardant properties without using PE. Adding PE causes poor flammability, while using PU and SiO2 prevents flame extensibility of the composites. In addition, SiO2 and ATH synergistically improved both mechanical and dynamical mechanical properties. This is attributed to the reinforcement of SiO2 particles inside the matrix, whereas the ATH releases water as a flame retardant. The V-0 composites tested with UL-94 showed acceptable heat resistance, strength, and durability, making them suitable for interior and exterior applications in buildings without the lightweight requirement. [ABSTRACT FROM AUTHOR]

This study aims to increase the flame retardancy of epoxy‐based composites by using various flame retardants together with colemanite filler (CLM), which is a very mineral‐rich boron type. As a flame retardant, aluminum hydroxide (Al(OH)3) and boron‐containing compounds: borax (BRX) and natural minerals (tincal (TNC) and colemanite (CLM)), as well as barium metaborate (BaMB) synthesized by us were used. Scanning electron microscopy (SEM), x‐ray powder diffraction (XRD), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), contact angle (CA), and particle size analysis were used to characterize the composites and additives. All boron compounds increased the thermal stability of the composites. Except for the ER/CLM‐BaMB composite, other composites' surface contact angles were over 90°. In terms of both combustion and thermal properties, the best CLM‐BaMB‐Al(OH)3‐TNC ratio was determined as 15:5:15:15. The tensile strength, self‐extinguishing time, estimated and experimental Limited Oxygen Index (LOI) values for this composite were determined as 96 MPa, 65 s, 29.6%, and 25%, respectively. In addition, ANOVA was applied to determine the effect of hybrid filler type and different weight ratios on the mechanical properties of composites. [ABSTRACT FROM AUTHOR]

Natural fiber composites are not suitable for use in industries due to their flammability and low thermal resistance. Inorganic metal‐based fillers are known to enhance the flammability and thermal resistance of composites, while the thermal and fire‐retardant properties of organic fillers are not commonly known. This study evaluated the mechanical, thermal, and flammability properties of Ceiba petandra fiber (CPF)‐reinforced composites, which were added with snail powder (SP). To study the thermal resistance of the composite, a dynamic mechanical analyzer (DMA) and thermogravimetric analysis (TGA) were applied. SP Filler concentration increased the composite's tensile strength and thermal resistance. DMA test results showed the same trend as the composite's density value. The flame rate parameters of the composite, including the percentage of char yield and the limitation index oxygen (LOI), rose as the SP filler increased. However, the flame rate of the composite dropped because SP filler inhibited the movement of oxygen, combustible gas, and polyester degradation products. The addition of organic fillers in natural fiber composites promises better flammability and thermal resistance. [ABSTRACT FROM AUTHOR]

This study focuses on examining the influence of bast fibers on the flammability and thermal properties of the polylactide matrix (PLA). For this purpose, Urtica dioica and Vitis vinifera fibers were subjected to two types of modifications: mercerization in NaOH solution (M1 route) and encapsulation in an organic PLA solution (M2 route). In a further step, PLA composites containing 5, 10, and 15 wt% of unmodified and chemically treated fibers were obtained. The results of the tests show that only biocomposites containing mercerized fibers had a nearly 20% reduced flammability compared to that of PLA. Moreover, the biofiller obtained in this way belongs to the group of flame retardants that generate char residue during combustion, which was also confirmed by TGA tests. The M2 modification route allowed to achieve higher mass viscosity than the addition of unmodified and M1-modified fibers. The reason is that fibers additionally encapsulated in a polymer layer impede the mobility of the chain segments. The inferior homogenization of the M2-modified fibers in the PLA matrix translated into a longer combustion time and only a 15% reduction in flammability. [ABSTRACT FROM AUTHOR]

This study focuses on examining the influence of bast fibers on the flammability and thermal properties of the polylactide matrix (PLA). For this purpose, Urtica dioica and Vitis vinifera fibers were subjected to two types of modifications: mercerization in NaOH solution (M1 route) and encapsulation in an organic PLA solution (M2 route). In a further step, PLA composites containing 5, 10, and 15 wt% of unmodified and chemically treated fibers were obtained. The results of the tests show that only biocomposites containing mercerized fibers had a nearly 20% reduced flammability compared to that of PLA. Moreover, the biofiller obtained in this way belongs to the group of flame retardants that generate char residue during combustion, which was also confirmed by TGA tests. The M2 modification route allowed to achieve higher mass viscosity than the addition of unmodified and M1-modified fibers. The reason is that fibers additionally encapsulated in a polymer layer impede the mobility of the chain segments. The inferior homogenization of the M2-modified fibers in the PLA matrix translated into a longer combustion time and only a 15% reduction in flammability.

• Tannic acid is neither a good flame retardant nor a highly swelling material. • TA combined with CLS reduces flammability of biocomposite by 30 % compared to PLA. • Mixing of TA with CLS in melt doesn't allow for PHRR reduction of more than 20 %. The purpose of this study was to determine the quantitative and qualitative effects of the form of natural phenolic compounds (NPCs) on the decomposition of polylactide (PLA) under different measurement conditions. For this purpose, thermogravimetry analysis (TGA), differential scanning calorimetry (DSC), and pyrolysis-combustion flow calorimetry (PCFC) analyses were carried out not only on individual raw materials like calcium lignosulfonate (BX), tannic acid (TA), BX chemically modified with TA (BMT), but also on PLA/BX, PLA/TA, and PLA/BMT composites with 3, 6, and 9 wt.% of filler. Moreover, the work checked whether to obtain satisfactory results it is necessary to carry out chemical modification lasting many hours, or whether simple physical mixing of ingredients (TABX) is enough, e.g. in proportions 1:2, 2:4, 3:6. The results of these analyses showed that TA is neither a good flame retardant nor a highly swelling material, but when combined with BX physically or chemically, it can produce an interesting synergistic effect. This work proves that chemically obtained BMT hybrid material allows to reduce flammability by 30 % compared to PLA which cannot be achieved by physically mixing these components in a polymer melt. On the other hand, the addition of TABX is sufficient to achieve a good thermal stabilization effect under processing conditions. [Display omitted] [ABSTRACT FROM AUTHOR]