Search

• The addition of nickel ions to the co-precipitation can produce a new hydrotalcite adsorbent with a better structure (FeMnNi-LTH). • Lead and cadmium can be strongly adsorbed by FeMnNi-LTH during a broad pH range. • The adsorption of Pb and Cd by FeMnNi-LTH can theoretically reach 279.13 mg/g and 76.99 mg/g at 25 °C. • FeMnNi-LTH adsorbs heavy metal ions mainly through precipitation and surface complexation. This paper discusses the application of a layered triple hydroxide (FeMnNi-LTH) in removing Pb2+ and Cd2+ ions from aqueous solutions. The material was synthesized via co-precipitation, adhering to a molar ratio of 1:1:2 (Fe:Mn:Ni). It was characterized using FTIR, XRD, SEM and TEM. The results indicate that the synthesized material is classified as a hydrotalcite and exhibits a well-defined layered structure. Batch experiments were conducted to investigate the adsorption of Pb2+ and Cd2+ by FeMnNi-LTH, taking into account various factors such as coexisting ions, pH, temperature, adsorbent dosage, and contact time. The experimental results showed that the adsorption capacity of this material for Pb2+ and Cd2+ was 253.89 mg/g and 56.90 mg/g at 25 °C, respectively. Moreover, it exhibits a consistent high adsorption capacity across a broad pH range (pH 3–5.5). When cations coexist, they compete for adsorption sites in the following order: Zn2+ > Ca2+ > Mg2+ > Cd2+/Pb2+. Based on the calculated thermodynamic parameters, it is inferred that the adsorption process is endothermic and spontaneous. The adsorption mechanism, as analyzed by modeling and characterization, involves isomorphic substitution, surface complexation, precipitation, electrostatic attraction, and physical adsorption. The quantitative analysis of the adsorption mechanism revealed that FeMnNi-LTH primarily adsorbs Pb2+ and Cd2+ via precipitation and surface complexation. It was revealed by comparison with other adsorbents that the synthesized FeMnNi-LTH can be used for remediation of heavy metal pollution in water. [ABSTRACT FROM AUTHOR]

In this study, modified activated carbon fibers and phytic acid-doped polyaniline/activated carbon fiber composites were successfully prepared by modifying activated carbon fibers and compounding polyaniline. The electrokinetic adsorption combined remediation technology was used to study the remediation of cadmium-contaminated soil. The results showed that when the electric field intensity was 2 V cm−1 and the repair time was 120 h, 0.1 mol L−1 citric acid solution was circularly added to the cathode using electrolyte. The current during the repair process showed periodic fluctuations with the extension of the repair time. The current of adding P-PANI/ACF adsorbent near the cathode region was larger than that of other groups, and cadmium has a higher removal rate. The mean removal rate of Cd(II) in soil with a content of 60 mg kg−1 reach 76.94%. [ABSTRACT FROM AUTHOR]

The slowed adsorption kinetics caused by the constricted pore shape of adsorbents is a significant obstacle in heavy metal ion adsorption. In order to develop effective and environmentally friendly adsorbents for the removal of heavy metal ions, particularly from phosphoric acid medium, novel resources are needed. Biochar, generated from waste biomass as a low-cost and non-toxic material, is currently attracting a great deal of interest as a potential solution. In this study, banana pseudostem was selected and pyrolyzed at 650°C to evaluate its effect on cadmium adsorption. The resulting biochar was characterized in terms of its structural, physical, morphological, and thermal properties to determine its physicochemical features. The biochar's adsorption efficiency towards Cd removal from industrial phosphoric acid was also evaluated through a series of batch experiments by varying different parameters, including contact time (30-60-180 min), temperature (298.15-308.15-318.15 K), and adsorbent amount (0.05-0.1-0.15-0.2 g). Results from ICP measurements showed that the removal rate of Cd decreased when both time and biochar dosage increased, while temperature had little effect on the extraction process. The biochar was most effective with a removal rate of 12.5 mg/g at 308.15 K by adding 50 mg of biochar for 30 min. These findings suggest that biochar derived from banana pseudostem is a promising biosorbent for Cd removal from industrial phosphoric acid. [ABSTRACT FROM AUTHOR]

The structure and properties of basic metal-organic frameworks (MOFs) continue to exhibit low Cd(II) uptake and selectivity. Assembly of same zinc-based MOF building blocks into a dual-zinc MOF@MOF composite could offer a promising avenue for efficiently capturing Cd(II) from aqueous solutions. This paper reports a dual-zinc MOF@MOF (Zn-BTC@ZIF-8, DZM) adsorbent, which was constructed for boosting the performances of adsorption and separation. The adsorption behavior of Cd(II) onto DZM from aqueous solution is thoroughly examined at room temperature. Results indicates that the DZM demonstrates significant capability in capturing Cd(II), attributed to the synergistic effects of Zn-BTC and ZIF-8 with diverse active sites, appropriate pore sizes and shapes, stable dual zinc bonding interaction, and more. The maximum Cd(II) uptake capacity reached 150 mg/g, with rapid attainment of adsorption equilibrium within just 20 min, surpassing the performance of other reported adsorbents in the literature. The adsorption data align well with both the Freundlich and pseudo-second-order kinetic models. The process of adsorption is a process of spontaneous heat absorption and increasing degrees of freedom. Particularly noteworthy is the sustained effectiveness of DZM in capturing Cd(II) even after the fifth cycle. This research introduces a fresh approach to crafting desirable MOF@MOF configurations, thereby advancing their potential utility in Cd(II) removal from water. [Display omitted] • A new-style dual-zinc MOF@MOF (Zn-BTC@ZIF-8) adsorbent was first constructed. • The Zn-BTC@ZIF-8 composite exhibits adsorption performance toward Cd(II). • Double MOF structure is beneficial to expose more active sites and facilitate Cd(II) capture. [ABSTRACT FROM AUTHOR]

This study aimed to investigate the adsorption efficiency of Cd and Mn using natural sorbents—bentonite, zeolite and stabilized digested dewatered waste sludge. The main contributions of the scientific article are in adding to the scientific knowledge of the use of natural and waste sorbents in the removal of heavy metals from neutral mine effluents. Current studies mainly focus on metal removal by sorption using natural sorbents from acid mine drainage. This study investigates sorption in neutral mine drainage. The efficiency of the sorption process was evaluated using the following parameters: efficiency (%) of metal ion removal, Freudlich and Langmuir adsorption isotherm constant. The AES–ICP method (atomic emission spectrometry with inductively coupled plasma) was used for the initial metal analysis of the materials used. The atomic absorption spectrometry (AAS) method was used for the analysis of Cd and Mn in the sorption process. The maximum efficiency of Mn removal by bentonite at the end of the test was approximately 90%. The removal of Mn by zeolite was considerably lower—about 20% compared to the use of sludge—80%. Based on the sorption efficiency, the sludge was suitable for sorption. Much higher levels of Cd sorption were achieved using sludge compared to using natural bentonite and zeolite. The main novelty of the work lies in the sorption of metals using dewatered digested sludge. Previous studies have focused on metal sorption using activated sludge. Most previous studies focused on sorption from acid mine drainage. The novelty of this study is that we focused on the sorption of neutral mine drainages, which are typical for the location we are monitoring. [ABSTRACT FROM AUTHOR]

In this research, the adsorption of nickel (Ni), copper (Cu), cadmium (Cd), and zinc (Zn) from real sulfuric leaching solution with weakly acidic resins has been studied using response surface methodology (RSM). The adsorption process on two weakly acidic resins has been investigated as a function of pH, time, temperature, and resin dosage. The experimental results indicate that the amino phosphoric acid resin removed Ni, Cu, Cd, and Zn from an acidic solution very efficiently. Based on the central composite design (CCD) on the RSM, the statistical criteria of correlation coefficient (R2) values of Ni, Cu, Cd, and Zn are 0.9418, 0.9753, 0.9657, and 0.9189, respectively. The adsorption process followed the pseudo-second-order kinetic model and the thermodynamic calculations indicated the chemical interaction between the resin surface and the metal ions. Enthalpy values greater than zero indicate that the adsorption reaction of the metals is endothermic. The optimal adsorption process was carried out at time of 20 min, temperature of 30 0C, pH of 5, and resin dosage of 4 g/L. In these conditions, the adsorption capacity of nickel, copper, cadmium, and zinc were obtained 13.408, 7.087, 4.357, and 15.040 mg/g, respectively. [ABSTRACT FROM AUTHOR]

Copyright of Polymer Materials Science & Engineering is the property of Sichuan University, Polymer Research Institute and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Chlorella vulgaris is an inexpensive microalga that could be employed for environmental remediation, but further investigations are needed to assess its suitability and optimal treatment methodology. With this aim in mind, this study focused on the raw biomass and the biochar and hydrochar obtained from it, analyzing their physicochemical properties and testing them to capture cadmium from an aqueous environment. The adsorption/absorption tests assessed the effect of adsorbent dosage, pH, Cd concentration, and contact time, and the results were analyzed through a structural equation model. Biochar and hydrochar performed similarly and better than the raw biomass, with the highest Cd removal observed at an adsorbent dosage of 0.8 g L−1, an initial concentration of Cd solution of 30 mg L−1, a pH of 6, and a contact time of 30 min. The adsorption isotherm data for Cd could be well-described by the Langmuir and Temkin models. The results from the structural equation modeling revealed that the variables material type, dosage, and concentration all contributed to Cd removal in water, with time mediating these effects. [ABSTRACT FROM AUTHOR]

With the development of industrial activities and the agricultural and mining industries, farmland soils are facing serious problems related to heavy metal contamination, especially cadmium (Cd) and arsenic (As) contamination. In this study, two industrial by-products, phosphogypsum (PG) and red mud (RM), were modified by lanthanum (La) impregnation to form a new composite (L-PR) to investigate the adsorption performance of Cd(II)/As(V) in both single and binary systems. The adsorption mechanisms of Cd(II)/As(V) on L-PR were analyzed using SEM, XRD, FTIR, and XPS. The passivation effect of L-PR on the Cd-As composite contaminated soil was confirmed through a soil cultivation experiment. The adsorption experiments revealed that L-PR showed superior adsorption capabilities for Cd(II) and As(V) compared to PG and RM. Additionally, L-PR was found to be less affected by changes in pH. The kinetic studies indicated that Cd(II) and As(V) adsorption by L-PR followed the second-order kinetic model most accurately. Isothermal adsorption experiments revealed that the adsorption of Cd(II) by L-PR was more in accordance with the Freundlich model, while As(V) was more in accordance with the Langmuir model. The mechanisms of Cd(II) and As(V) adsorption on L-PR involved electrostatic attraction, ion exchange, complexation, and precipitation. The adsorption of Cd(II) is dominated by complexation and precipitation, and the adsorption of As(V) is dominated by ion exchange and complexation. Soil cultivation experiments showed that L-PR significantly reduced the available Cd and As concentrations in soil by 86.01% and 27.80%, respectively, and it could induce the transformation of non-stable Cd(II)/As(V) to the more stable residual. In summary, L-PR exhibits facile preparation, excellent adsorption performance, and is capable of simultaneously removing Cd(II) and As(V) from aqueous solutions while immobilizing these contaminants in soil. These remarkable attributes made it a highly promising alternative for the simultaneous treatment of various toxic metal contaminants. [ABSTRACT FROM AUTHOR]

In order to enhance the removal of cadmium from phosphoric acid, it is imperative to explore novel resources that may be utilized for the development of highly effective and environmentally sustainable adsorbents. Cellulose beads are composed of naturally occurring polysaccharide fibers and find extensive utilization across several industrial sectors and applications. Within this framework, this research paper presents a green and simple method for producing porous cellulose beads using date palm fibers as the preferred raw material. The innovation lies in immersing the obtained cellulose beads in a Polyvinyl fluoride (PVDF)/ N , N -dimethylformamide (DMF) suspension as a coating polymer with different concentrations (2.5, 5, 10 %) to maintain their stability in an acidic environment. The surface of cellulose/PVDF beads were subjected to multiple characterizations like Fourier transform infrared (FTIR) spectroscopy, Scanning electron microscopy (SEM), Thermogravimetric analysis (TGA), size distribution then pH stability confirming that the coating has been perfectly achieved and conserved well the shape of the beads. The coated cellulose/PVDF-2.5 % underwent evaluation by the process of batch adsorption experiments while different parameters were varied including contact time (5, 10, 20, 30, 60, 90 min), temperature (25, 35, 45 and 55 °C), and adsorbent mass (20, 40, 60, 80 and 100 mg). The obtained ICP data showed that the adsorption rate of Cd (II) from phosphoric acid medium decreased while increasing both temperature from 25 to 55 °C and contact time from 5 to 90 min while adding more adsorbent dosage from 20 to 100 mg enhanced the removal percentage. The cellulose/PVDF-2.5 % was more effective with an adsorption capacity equal to 3.4998 mg/g at optimal conditions including 25 °C as the temperature after 5 min as contact time and by adding a mass 100 mg of the biosorbent while the pH = 2 of the solution is maintained the same. The examined material's adsorption processes proved to be exothermic and non-spontaneous, and it proved that the pseudo-second-order model provided the best match for the cellulose/PVDF-2.5 % beads kinetics data. Furthermore, the cellulose beads exhibited exceptional reusability for up to four repeated cycles without undergoing desorption. The present study offers a viable approach for producing environmentally sustainable biomass-derived adsorbents. Additionally, the study validates the potential of cellulose/PVDF beads as an intriguing material for phosphoric acid decadmiation. [ABSTRACT FROM AUTHOR]

This study explores the potential of modified shrimp-based chitosan (MSC) as an innovative adsorbent for eliminating heavy metals (HMs) from contaminated water sources. The modifications encompassed various chemical treatments, surface functionalization, and structural optimization to enhance the chitosan's adsorption capabilities. Comprehensive analyses using FT-IR and SEM-EDS were conducted to evaluate the properties of the chitosan. The adsorption capacity of MSC was assessed using ICP-MS before and after the adsorption process. Moreover, the study investigated the efficiency of HM removal by MSC under different conditions, including variations in pH, adsorbent dosage, and contact time. Under neutral pH conditions, the highest adsorption rates of copper, zinc, cadmium, and lead were determined as 99.72%, 84.74%, 91.35%, and 99.92%, respectively, with corresponding adsorption capacities of 20.30 mg/g for copper, 7.50 mg/g for zinc, 15.00 mg/g for cadmium, and 76.34 mg/g for lead. Analysis based on the Langmuir and Freundlich isotherm models revealed highly significant adsorption of HMs, supported by strong correlation coefficients (r2 > 0.98) obtained from the data. The pseudo-second-order kinetic model with linear coefficients (r2) greater than 0.97 effectively explained the kinetic studies of metal adsorption employing modified shrimp shells. These coefficients indicate a robust fit of the models to the experimental adsorption data for heavy metals. Further confirmation of the effectiveness of the adsorbent was obtained through FT-IR spectroscopy, which confirmed the presence of specific functional groups on the adsorbent, such as N–H joined with –COO−, H–O, C−O−C, and C–H. Additionally, the SEM-EDS analysis detected the presence of elements on the surface of MSC chitosan. The results emphasize that MSC is a highly effective and cost-efficient adsorbent for eliminating Cu, Zn, Cd, and Pb from wastewater, making it a promising eco-friendly choice. [ABSTRACT FROM AUTHOR]