Search

NiFe2O4 material is grown on carbon paper (CP) with the hydrothermal method for use as electrocatalysts in an alkaline electrolyzer. NiFe2O4 material is used as the anode and cathode catalysts (named NiFe(+)/NiFe(−) hereafter). The results are compared with those obtained using CP/NiFe as the anode and CP/Ru as the cathode (named NiFe)(+)/Ru(−) hereafter). During cell operation with NiFe(+)/Ru(−), the current density reaches 500 mA/cm2 at a cell voltage of 1.79 V, with a specific energy consumption of 4.9 kWh/m3 and an energy efficiency of 66.2%. In comparison, for NiFe(+)/NiFe(−), the current density reaches 500 mA/cm2 at a cell voltage of 2.23 V, with a specific energy consumption of 5.7 kWh/m3 and an energy efficiency of 56.6%. The Faradaic efficiency is 96–99%. With the current density fixed at 400 mA/cm2, after performing a test for 150 h, the cell voltage with NiFe(+)/Ru(−) increases by 0.167 V, whereas that with NiFe(+)/NiFe(−) decreases by only 0.010 V. Good, long-term stability is demonstrated. [ABSTRACT FROM AUTHOR]

Carbon containing waste has a certain calorific value and utilization value due to the presence of carbon elements. However, the current treatment methods are mostly traditional landfill disposal, incineration, or expensive physical and chemical reaction methods, which clearly do not comply with the rules of the current clean and resource-saving society. In this paper, a new technology and system for carbon containing wastes is proposed, which comprehensively treats and recycles carbon containing wastes, including solid waste, wastewater, waste gas, etc., using pyrolysis–gasification two-stage-cycle technology. The calculation results indicate that the technical scheme proposed in this article is feasible and can achieve the recycling of intermediate and final products, the efficient and clean utilization of carbon containing waste, and the graded utilization of energy. The clean utilization rate of carbon containing waste can be effectively improved, the energy consumption and cost of separate treatments can be reduced, and zero waste emissions can be completely achieved by the comprehensive pyrolysis–gasification two-stage-cycle treatment and resource utilization technology, which is one of the preferred solutions for future resource-saving societies. [ABSTRACT FROM AUTHOR]

In recent decades, artificial intelligence has undergone transformative advancements, reshaping diverse sectors such as healthcare, transport, agriculture, energy, and the media. Despite the enthusiasm surrounding AI's potential, concerns persist about its potential negative impacts, including substantial energy consumption and ethical challenges. This paper critically reviews the evolving landscape of AI sustainability, addressing economic, social, and environmental dimensions. The literature is systematically categorized into "Sustainability of AI" and "AI for Sustainability", revealing a balanced perspective between the two. The study also identifies a notable trend towards holistic approaches, with a surge in publications and empirical studies since 2019, signaling the field's maturity. Future research directions emphasize delving into the relatively under-explored economic dimension, aligning with the United Nations' Sustainable Development Goals (SDGs), and addressing stakeholders' influence. [ABSTRACT FROM AUTHOR]

This paper addresses the challenges in forecasting electrical energy in the current era of renewable energy integration. It reviews advanced adaptive forecasting methodologies while also analyzing the evolution of research in this field through bibliometric analysis. The review highlights the key contributions and limitations of current models with an emphasis on the challenges of traditional methods. The analysis reveals that Long Short-Term Memory (LSTM) networks, optimization techniques, and deep learning have the potential to model the dynamic nature of energy consumption, but they also have higher computational demands and data requirements. This review aims to offer a balanced view of current advancements and challenges in forecasting methods, guiding researchers, policymakers, and industry experts. It advocates for collaborative innovation in adaptive methodologies to enhance forecasting accuracy and support the development of resilient, sustainable energy systems. [ABSTRACT FROM AUTHOR]

A cut-to-length (CTL) forest harvester is a purpose-built, hydraulically actuated mobile work machine used for felling, delimbing, and cross-cutting trees into dimensions and assortments. In such a machine, the diesel engine load is known to fluctuate greatly over the work cycle. To manage these changing power demands, a hydraulic hybrid system is implemented into a full-scale proof-of-concept machine to discover its functionality and to collect experimental results in real operating conditions. The hydraulic hybrid system installed on a CTL harvester machine was tuned to enable the collection of two actual datasets of timber harvesting, and data collection over a period of production use was carried out. In addition to updating the state-of-the-art research into heavy non-road mobile machinery regarding hybrid systems, this paper discusses the two tests carried out in actual production conditions with the studied hydraulic hybrid system. The adaptations and modifications to the studied and tested system since earlier papers are discussed—especially the improvements in the system dynamics and response as well as the control of the hybrid system. In conclusion, the tested system can be said to operate satisfactorily and shows clear advantages over the conventional system, even though it still has some limitations. The results show that the system has the potential to increase the productivity of the machine through the demonstrated higher peak power, as well as showing improvement in fuel efficiency under highly fluctuating loads, especially with heavy or large-volume tree stems. [ABSTRACT FROM AUTHOR]

This paper introduces a groundbreaking approach to demand response management, aiming to empower consumers through innovative strategies. The key contribution is the concept of "acquiring flexibility rights", wherein consumers engage with power aggregators to curtail energy usage during peak-load periods, receiving incentives in return. A flexibility right coefficient is introduced, allowing consumers to tailor their participation in demand response programs, ensuring their well-being. Additionally, a lighting intensity control system is developed to enhance residential lighting network efficiency. The study demonstrates that high-energy consumers, adopting a satisfaction factor of 10, can achieve over 61% in electricity cost savings by combining the lighting control system and active participation in demand response programs. This not only reduces expenses but also generates income through the sale of flexibility rights. Conversely, low-energy consumers can fully offset their expenses and accumulate over USD 33 in earnings through the installation of solar panels. This paper formulates an optimization problem considering flexibility rights, lighting control, and time-of-use tariff rates. An algorithm is proposed for a distributed solution, and a sensitivity analysis is conducted for evaluation. The proposed method showcases significant benefits, including cost savings and income generation for consumers, while contributing to grid stability and reduced blackout occurrences. Real data from a residential district in Tehran validates the method's effectiveness. This study concludes that this approach holds promise for demand response management in smart grids, emphasizing the importance of consumer empowerment and sustainable energy practices. [ABSTRACT FROM AUTHOR]

Solar energy is not only the most abundant energy on earth but it is also renewable. The use of this energy is expanding very rapidly mainly through photovoltaic technology. However, electricity storage remains a bottleneck in tackling solar resource variability. Thus, solar thermal energy becomes of particular interest when energy storage is required, as thermal energy storage is much cheaper than electricity storage. The objective of this paper is to make a short update on the CSP (Concentrated Solar Power) market as of the year 2023. It is based on the CSP-GURU database, which lists information on CSP power plants all over the world. Although this database is open, it is not easy to find UpToDate analysis. An overview of this expanding technology is presented and offers readable figures with the most important information. This includes the evolution of installed capacities worldwide along with upcoming projects (under construction) and technological trends. The evolution of storage capacities and operating temperatures is discussed. Investment costs and levelized cost of electricity are also provided to obtain reliable data for comparison with other energy technologies. Specific land requirements are highlighted, along with overall efficiency. Relevant examples are discussed in this paper. Eventually, it outlines the evolution of the CSP landscape with useful information for scientific and educational purposes. [ABSTRACT FROM AUTHOR]

The Qinghai–Tibet plateau, with an average altitude of over 4000 m, has low annual average temperatures and a high demand for building heating. This region's abundant solar energy resources hold substantial practical significance for improving the indoor heat environment and reducing building energy consumption. This paper investigates the impact of orientation and skylight area ratio on building heat load and indoor temperature, using both actual measurement and simulation methods, with a case study of the comprehensive building at Beiluhe Observation and Research Station of Frozen Soil Engineering and Environment (Beiluhe Station), located in the Qinghai–Tibet Plateau region. Initially, a model was established using the EnergyPlus 9.4 software, with orientation variables set from east to west in 15° increments, to simulate the variations in building heat load resulting from orientation changes; simulations were then conducted for three different skylight area ratios under the optimal orientation to evaluate their influence on heat load and indoor temperature. The results show that for the architectural style examined in this paper, the optimal building orientation within the region is 30° south by east, with the optimal orientation range spanning from 45° south by east to due south. Heating load is negatively correlated with the skylight area ratio, and beyond a certain threshold, the rate of decrease in heat load diminishes or even stabilizes. The conclusions of this paper offer guidance for the orientation and skylight design of new buildings on the Qinghai–Tibet Plateau. [ABSTRACT FROM AUTHOR]

In order to cope with the problems of energy shortage and environmental pollution, carbon emissions need to be reduced and so the structure of the power grid is constantly being optimized. Traditional centralized power networks are not as capable of controlling and distributing non-renewable energy as distributed power grids. Therefore, the optimal dispatch of microgrids faces increasing challenges. This paper proposes a multi-strategy fusion slime mould algorithm (MFSMA) to tackle the microgrid optimal dispatching problem. Traditional swarm intelligence algorithms suffer from slow convergence, low efficiency, and the risk of falling into local optima. The MFSMA employs reverse learning to enlarge the search space and avoid local optima to overcome these challenges. Furthermore, adaptive parameters ensure a thorough search during the algorithm iterations. The focus is on exploring the solution space in the early stages of the algorithm, while convergence is accelerated during the later stages to ensure efficiency and accuracy. The salp swarm algorithm's search mode is also incorporated to expedite convergence. MFSMA and other algorithms are compared on the benchmark functions, and the test showed that the effect of MFSMA is better. Simulation results demonstrate the superior performance of the MFSMA for function optimization, particularly in solving the 24 h microgrid optimal scheduling problem. This problem considers multiple energy sources such as wind turbines, photovoltaics, and energy storage. A microgrid model based on the MFSMA is established in this paper. Simulation of the proposed algorithm reveals its ability to enhance energy utilization efficiency, reduce total network costs, and minimize environmental pollution. The contributions of this paper are as follows: (1) A comprehensive microgrid dispatch model is proposed. (2) Environmental costs, operation and maintenance costs are taken into consideration. (3) Two modes of grid-tied operation and island operation are considered. (4) This paper uses a multi-strategy optimized slime mould algorithm to optimize scheduling, and the algorithm has excellent results. [ABSTRACT FROM AUTHOR]

This paper focuses on optimizing the Zuker RNA folding algorithm, a bioinformatics task with non-serial polyadic dynamic programming and non-uniform loop dependencies. The intricate dependence pattern is represented using affine formulas, enabling the automatic application of tiling strategies via the polyhedral method. Three source-to-source compilers—PLUTO, TRACO, and DAPT—are employed, utilizing techniques such as affine transformations, the transitive closure of dependence relation graphs, and space–time tiling to generate cache-efficient codes, respectively. A dedicated transpose code technique for non-serial polyadic dynamic programming codes is also examined. The study evaluates the performance of these optimized codes for speed-up and scalability on multi-core machines and explores energy efficiency using RAPL. The paper provides insights into related approaches and outlines future research directions within the context of bioinformatics algorithm optimization. [ABSTRACT FROM AUTHOR]