Search

The continuous upgrading of electronic technology has facilitated the integration and miniaturization of electronic and electrical equipment, as well as putting great pressure on the multifunctional demand for internal materials. Developing insulating materials with both low permittivity and high thermal conductivity has become imperative. This perspective focuses on polyimide (PI), which is the top material of the polymer material pyramid, discusses the characteristic parameters that affect its dielectric property and thermal conductivity. A series of basic schemes to regulate the dielectric/thermal properties of PI are summarized, revealing the bottlenecks and drawbacks of the current research. Future development trends of PIs featured low permittivity-high thermal conductivity are anticipated, and novel ideas are proposed for the development of new generation of multifunctional PIs. [ABSTRACT FROM AUTHOR]

Magnetorheological (MR) foam has become a potential soft robotic gripper-based material that can provide a better grasping force and handling objects due to its ability in varying stiffness in correspond to applied magnetic fields. However, MR foams are facing degradation issue that may reduce the storage modulus when often exposed to thermal exposure from the operating system of a device. Therefore, this study focuses on improving the storage modulus and simultaneously enhancing the thermal properties of MR foam. Hence, silica nanoparticles were introduced as an additive to achieve the improvement target. MR foams were embedded with different concentrations of silica nanoparticles from 0 to 5 wt.%, and the corresponding rheological properties was examined under different temperature conditions from 25 °C to 65 °C. The results revealed that increasing temperatures have reduced the storage modulus of MR foams, however, the embedded silica has countered the drawbacks by strengthening the interfacial interactions between CIP-polyurethane foam matrix. In addition, the morphological characteristics of MR foams also showed less debris or peel-off PU foam with silica nanoparticles. Besides, the silica nanoparticles have delayed the thermal degradation of MR foam for approximately 30 °C. [ABSTRACT FROM AUTHOR]

Platinum-carbon (PtC) composite nanowires were fabricated using focused electron beam induced deposition and postprocessed, and their performance as a nanoscale resistive thermal device (RTD) was evaluated. Nanowires were free-standing and deposited on a dedicated substrate to eliminate the influence of the substrate itself and of the halo effect on the results. The PtC free-standing nanowires were postprocessed to lower their electrical resistance using electron beam irradiation and thermal annealing using Joule heat both separately and combined. Postprocessed PtC free-standing nanowires were characterized to evaluate their noise figure (NF) and thermal coefficients at the temperature range from 30 K to 80 °C. The thermal sensitivity of RTD was lowered with the reduced resistance but simultaneously the NF improved, especially with electron-beam irradiation. The temperature measurement resolution achievable with the PtC free-standing nanowires was 0.1 K in 1 kHz bandwidth. [ABSTRACT FROM AUTHOR]

Melt treatment is well known to have an important influence on the properties of metallic glasses (MGs). However, for the MGs quenched from different melt temperatures with a quartz tube, the underlying physical origin responsible for the variation of properties remains poorly understood. In the present work, we systematically studied the influence of melt treatment on the thermal properties of a Zr50Cu36Al14 glass-forming alloy and unveiled the microscopic origins. Specifically, we quenched the melt at different temperatures ranging from 1.1 T l to 1.5 T l (T l is the liquidus temperature) to obtain melt-spun MG ribbons and investigated the variation of thermal properties of the MGs upon heating. We found that glass transition temperature, T g, increases by as much as 36 K, and the supercooled liquid region disappears in the curve of differential scanning calorimetry when the melt is quenched at a high temperature up to 1.5 T l. The careful chemical analyses indicate that the change in glass transition behavior originates from the incorporation of oxygen and silicon in the molten alloys. The incorporated oxygen and silicon can both enhance the interactions between atoms, which renders the cooperative rearrangements of atoms difficult, and thus enhances the kinetic stability of the MGs. [ABSTRACT FROM AUTHOR]

Objective. Thermal property (TP) maps of human tissues are useful for tumor treatment and diagnosis. In particular, the blood perfusion rate is significantly different for tumors and healthy tissues. Noninvasive techniques that reconstruct TPs from the temperature measured via magnetic resonance imaging (MRI) by solving an inverse bioheat transfer problem have been developed. A few conventional methods can reconstruct spatially varying TP distributions, but they have several limitations. First, most methods require the numerical Laplacian computation of the temperature, and hence they are sensitive to noise. In addition, some methods require the division of a region of interest (ROI) into sub-regions with homogeneous TPs using prior anatomical information, and they assume an unmeasurable initial temperature distribution. We propose a novel robust reconstruction method without the division of an ROI or the assumption of an initial temperature distribution. Approach. The proposed method estimates blood perfusion rate maps from relative temperature changes. This method avoids the computation of the Laplacian by using integral representations of the Helmholtz decomposition of the heat flux. Main Result. We compare the reconstruction results of the conventional and proposed methods using numerical simulations. The results indicate the robustness of the proposed method. Significance. This study suggests the feasibility of thermal property mapping with MRI using the robust proposed method. [ABSTRACT FROM AUTHOR]

Short Sansevieria cylindrica fibre/polylactic acid composites (SCFP) were fabricated using a twin screw extruder followed by the hot press technique, with variations in fibre loadings of 10 wt%, 20 wt%, 30 wt% and 40 wt%. The thermal properties of SCFP were assessed through dynamic mechanical analysis (DMA), thermomechanical analysis (TMA), thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). Notably, the samples loaded with 40 wt% of fibre exhibited an increased storage modulus. In terms of loss modulus, the fibre-loaded samples displayed high values, indicating more heat is released during DMA experiment. Interestingly, the composite trend did not solely rely on increasing fibre loading, highlighting the intricate interplay between reinforcement and matrix crucial for determining viscoelastic properties across various temperatures. The TGA results revealed a decrease in inflection temperature with increasing fibre loadings, accompanied by a proportional rise in residues. The DSC thermograms indicated minimal differences in T _g , T _cc , and T _m values among composites with varying fibre loadings. However, neat PLA showed slightly higher values than the composites. On the other hand, reinforcing SCF into the PLA matrix promoted the crystallization of PLA by 1%–3% with the maximum degree of crystallinity of 25.4% obtained for 30 wt% of SCFP.