Search

Purpose. Fast kV-switching (FKS) and dual-layer flat-panel detector (DL-FPD) technologies have been actively studied as promising dual-energy spectral imaging solutions for FPD-based cone-beam computed tomography (CT). However, cone-beam CT (CBCT) spectral imaging is known to face challenges in obtaining accurate and robust material discrimination performance. That is because the energy separation by either FKS or DL-FPD, alone, is still limited, along with apparently unpaired signal levels in the effective low- and high-energy projections in real applications, not to mention the x-ray scatter in cone-beam scan which will make the material decomposition almost impossible if no correction is applied. To further improve CBCT spectral imaging capability, this work aims to promote a source-detector joint multi-energy spectral imaging solution which takes advantages of both FKS and DL-FPD, and to conduct a feasibility study on the first tabletop CBCT system with the joint spectral imaging capability developed. Methods. For CBCT, development of multi-energy spectral imaging can be jointly realized by using an x-ray source with a generator whose kilo-voltages can alternate in tens of Hertz (i.e. FKS), and a DL-FPD whose top- and bottom-layer projections corresponds to different effective energy levels. Thanks to the complimentary characteristics inherent in FKS and DL-FPD, the overall energy separation will be significantly better when compared with FKS or DL-FPD alone, and the x-ray photon detection efficiency will be also improved when compared with FKS alone. In this work, a noise performance analysis using the Cramér–Rao lower bound (CRLB) method is conducted. The CRLB for basis material after a projection-domain material decomposition is derived, followed by a set of numerical calculations of CRLBs, for the FKS, the DL-FPD and the joint solution, respectively. To compensate for the slightly angular mismatch between low- and high- projections in FKS, a dual-domain projection completion scheme is implemented. Afterwards material decomposition from the complete projection data is carried out by using the maximum-likelihood method, followed by reconstruction of basis material and virtual monochromatic images (VMI). In this work, the first FKS and DL-FPD jointly enabled multi-energy tabletop CBCT system, to the best of our knowledge, has been developed in our laboratory. To evaluate its spectral imaging performance, a set of physics experiments are conducted, where the multi-energy and head phantoms are scanned using the 80/105/130 kVp switching pairs and projection data are collected using a prototype DL-FPD, whose both top and bottom layer of panels are composed of 550 μ m of cesium iodine (CsI) scintillators with no intermediate metal filter in-between. Results. The numerical simulations show that the joint spectral imaging solution can lead to a significant improvement in energy separation and lower noise levels in most of material decomposition cases. The physics experiments confirmed the feasibility and superiority of the joint spectral imaging, whose CNRs in the selected regions of interest of the multi-energy phantom were boosted by an average improvement of 21.9%, 20.4% for water basis images and 32.8%, 62.8% for iodine images when compared with that of the FKS and DL-FPD, respectively. For the head phantom case, the joint spectral imaging can effectively reduce the streaking artifacts as well, and the standard deviation in the selected regions of interest are reduced by an average decrement of 19.5% and 8.1% for VMI when compared with that of the FKS and DL-FPD, respectively. Conclusions. A feasibility study of the joint spectral imaging solution for CBCT by utilizing both the FKS and DL-FPD was conducted, with the first tabletop CBCT system having such a capability being developed, which exhibits improved CNR and is more effective in avoiding streaking artifacts as expected. [ABSTRACT FROM AUTHOR]

Objective. The aim of this study was to reconstruct volumetric computed tomography (CT) images in real-time from ultra-sparse two-dimensional x-ray projections, facilitating easier navigation and positioning during image-guided radiation therapy. Approach. Our approach leverages a voxel-sapce-searching Transformer model to overcome the limitations of conventional CT reconstruction techniques, which require extensive x-ray projections and lead to high radiation doses and equipment constraints. Main results. The proposed XTransCT algorithm demonstrated superior performance in terms of image quality, structural accuracy, and generalizability across different datasets, including a hospital set of 50 patients, the large-scale public LIDC-IDRI dataset, and the LNDb dataset for cross-validation. Notably, the algorithm achieved an approximately 300% improvement in reconstruction speed, with a rate of 44 ms per 3D image reconstruction compared to former 3D convolution-based methods. Significance. The XTransCT architecture has the potential to impact clinical practice by providing high-quality CT images faster and with substantially reduced radiation exposure for patients. The model's generalizability suggests it has the potential applicable in various healthcare settings. [ABSTRACT FROM AUTHOR]

Objective. To demonstrate that complete cone beam CT (CBCT) scans from both MV-energy and kV-energy LINAC sources can reduce metal artifacts in radiotherapy guidance, while maintaining standard-of-care x-ray doses levels. Approach. MV-CBCT and kV-CBCT scans are acquired at half normal dose. The impact of lowered dose on MV-CBCT data quality is mitigated by the use of a 4-layer MV-imager prototype and reduced LINAC energy settings (2.5 MV) to improve photon capture. Additionally, the MV-CBCT is used to determine the 3D position and pose of metal implants, which in turn is used to guide model-based poly-energetic correction and interleaving of the kV-CBCT and MV-CBCT data. Certain edge-preserving regularization steps incorporated into the model-based correction algorithm further reduce MV data noise. Main results. The method was tested in digital phantoms and a real pelvis phantom with large 2.5″ spherical inserts, emulating hip replacements of different materials. The proposed method demonstrated an appealing compromise between the high contrast of kV-CBCT and low artifact content of MV-CBCT. Contrast-to-noise improved 3-fold compared to MV-CBCT with a clinical 1-layer architecture at matched dose (37 mGy) and edge blur levels. Visual delineation of the bladder and prostate improved noteably over kV- or MV-CBCT alone. Significance. The proposed method demonstrates that a full MV-CBCT scan can be combined with kV-CBCT to reduce metal artifacts without resorting to complicated beam collimation strategies to limit the MV-CBCT dose contribution. Additionally, significant improvements in CNR can be achieved as compared to metal artifact reduction through current clinical MV-CBCT practices. [ABSTRACT FROM AUTHOR]

Cone-beam computed tomography (CBCT) is widely used in dental imaging, small animal imaging, radiotherapy, and non-destructive industrial inspection. The quality of CBCT images depends on the precise knowledge of the CBCT system's alignment. We introduce a distinct procedure, 'precision alignment loop (PAL)', to calibrate any CBCT system with a circular trajectory. We describe the calibration procedure by using a line-beads phantom, and how PAL determines the misalignments from a CBCT system. PAL also yields the uncertainties in the simulated calibration to give an estimate of the errors in the misalignments. From the analytical simulations, PAL can precisely obtain the source-to-rotation axis distance, and the geometric center G, 'the point in z -axis meets the detector', where the z -axis is coincident with the line from the x-ray source that intersects the axis of the rotation orthogonally. The uncertainties of three misalignment angles of the detector are within ±0.05°, which is close to ±0.04° for the results of Yang et al (2017 Med. Phys. 44 1692), but our method is easy and simple to implement. Our distinct procedure, on the other hand, yields the calibration of a micro-CT system and an example of reconstructed images, showing our calibration method for the CBCT system to be simple, precise, and accurate. [ABSTRACT FROM AUTHOR]

Objective. To create two non-coplanar, stereotactic ablative radiotherapy (SABR) lung patient treatment plans compliant with the radiation therapy oncology group (RTOG) 0813 dosimetric criteria using a simple, isocentric, therapy with kilovoltage arcs (SITKA) system designed to provide low cost external radiotherapy treatments for low- and middle-income countries (LMICs). Approach. A treatment machine design has been proposed featuring a 320 kVp x-ray tube mounted on a gantry. A deep learning cone-beam CT (CBCT) to synthetic CT (sCT) method was employed to remove the additional cost of planning CTs. A novel inverse treatment planning approach using GPU backprojection was used to create a highly non-coplanar treatment plan with circular beam shapes generated by an iris collimator. Treatments were planned and simulated using the TOPAS Monte Carlo (MC) code for two lung patients. Dose distributions were compared to 6 MV volumetric modulated arc therapy (VMAT) planned in Eclipse on the same cases for a Truebeam linac as well as obeying the RTOG 0813 protocols for lung SABR treatments with a prescribed dose of 50 Gy. Main results. The low-cost SITKA treatments were compliant with all RTOG 0813 dosimetric criteria. SITKA treatments showed, on average, a 6.7 and 4.9 Gy reduction of the maximum dose in soft tissue organs at risk (OARs) as compared to VMAT, for the two patients respectively. This was accompanied by a small increase in the mean dose of 0.17 and 0.30 Gy in soft tissue OARs. Significance. The proposed SITKA system offers a maximally low-cost, effective alternative to conventional radiotherapy systems for lung cancer patients, particularly in low-income countries. The system's non-coplanar, isocentric approach, coupled with the deep learning CBCT to sCT and GPU backprojection-based inverse treatment planning, offers lower maximum doses in OARs and comparable conformity to VMAT plans at a fraction of the cost of conventional radiotherapy. [ABSTRACT FROM AUTHOR]

Objective. This study aims at investigating a novel super resolution CBCT imaging approach with a dual-layer flat panel detector (DL-FPD). Approach. With DL-FPD, the low-energy and high-energy projections acquired from the top and bottom detector layers contain over-sampled spatial information, from which super-resolution CT images can be reconstructed. A simple mathematical model is proposed to explain the signal formation procedure in DL-FPD, and a dedicated recurrent neural network, named suRi-Net, is developed based upon the above imaging model to nonlinearly retrieve the high-resolution dual-energy information. Physical benchtop experiments are conducted to validate the performance of this newly developed super-resolution CBCT imaging method. Main Results. The results demonstrate that the proposed suRi-Net can accurately retrieve high spatial resolution information from the low-energy and high-energy projections of low spatial resolution. Quantitatively, the spatial resolution of the reconstructed CBCT images from the top and bottom detector layers is increased by about 45% and 54%, respectively. Significance. In the future, suRi-Net will provide a new approach to perform high spatial resolution dual-energy imaging in DL-FPD-based CBCT systems. [ABSTRACT FROM AUTHOR]