Search

On-demand transit (ODT) has been widely piloted in recent years by many transit agencies in response to changing travel behaviour and preferences among people. Some agencies have adopted ODT to replace underperforming bus routes, as part of a continuous service planning process while others incorporated it within network re-design. All these trends highlight the critical need for transit agencies to have guidance for incorporating ODT into transit network planning both at the strategic, tactical, and service planning levels. Thus, the purpose of this research is to provide a discussion of the key guiding principles to facilitate the development of transit networks with integrated on-demand and scheduled services. To achieve this goal, a thorough review of the states of practice and research was conducted. Findings from the practice review were also reinforced through ODT practitioners' engagement in Canada. This paper provides discussions on the service goals and objectives of an integrated network design and highlights the key planning requirements for developing integrated networks. At the service planning level, the paper provides a discussion on service goals, service design parameters, and scenario development of ODT service. • On-demand transit (ODT) have grown in many cities around the globe, mostly as pilot projects. • Review of the literature and practice shows that planning for ODT is based on best practices , without "built" guidelines. • Principles of planning are discussed within two applications, the network design level, and the service planning level. • Opportunities of integration and mode selection criteria are defined to integrated ODT with existing bus network. • Simulation and analytical tools are useful to complement the principles of planning in the decision-making processes. [ABSTRACT FROM AUTHOR]

• A model was created to examine the reliability of maintenance budget allocation. • The model was applied to network-level pavement maintenance in Canada. • The impacts of algorithm selection and parameter tuning were studied. • The significance of pavement clustering in increasing reliability was highlighted. • The importance of incorporating actual pavement improvement curves was clarified. The purpose of this paper is to increase the reliability of the network-level pavement maintenance budget allocation by reducing uncertainties of algorithm selection and parameter tuning. In this paper, reliability is defined as the ability of a network-level pavement maintenance plan to improve the condition of a pavement network within a certain budget. In order to quantify reliability, the reliability index is defined as the ratio between the post-maintenance network condition and the net maintenance cost. With this purpose in mind, a two-objective optimization model was developed. To test its applicability, the model was applied to a pavement network in Canada. The model was solved using the Non-Dominated Sorting Genetic Algorithm II and the differential evolution algorithms. Finally, the reliability indices of algorithms and termination criteria were computed. The results indicated that the differential evolution algorithm recommended less frequent but more intense interventions that made the solutions expensive and less reliable. This paper contributed to the network-level pavement maintenance body of knowledge by (1) developing a multi-objective optimization model to reduce uncertainties of parameter tuning and algorithm selection; (2) increasing the reliability of budget allocation; (3) showcasing the significance of pavement clustering in increasing reliability; and (4) developing and incorporating actual pavement improvement curves. [Display omitted] [ABSTRACT FROM AUTHOR]

The pulp and paper industry use biomass residues, such as paper sludge and bark as fuel to provide energy for their plants. However, issues such as high-water content or low heating value limit the amount of energy that can be utilized. Processes to improve heat generation include biomass densification, which facilitates transportation and handling and can increase energy yield. However, the technical feasibility of briquetting is a function of the feedstock and preprocessing. This study introduces a novel approach to briquette production from biomass residues by utilizing wet biomass with water as a natural binder, contrasting with conventional methods that require forced drying and/or the addition of binders. The objective of this research was to investigate the impact of briquetting both unprocessed biomass and post-hydrothermal carbonization. The study focused on manufacturing briquettes derived from different sources, including bark (Balsam fir), paper sludge, and hydrochar of paper sludge. The feedstock was characterized for ash content and higher heating value. Biomass particle size (range), moisture content (range), process temperature (range), process pressure (range), and process residence time (range) were varied in briquetting experiments to determine conditions to produce high-quality briquettes with minimal energy input. Moisture content as high a 50 wt% in feedstock produced technically feasible briquettes, with appropriate physical-mechanical properties (durability, volumetric expansion and apparent density), and energetic potential (calorific value). The addition of heat (pressing temperature of 150 °C) during the pressing process resulted in briquettes with enhanced physical-mechanical, and energetic properties, surpassing those produced at room temperature. Further tests with additional steps in the production process are required to meet commercialization standards in Canada, but the treatments conducted in this study effectively improved the energy potential of biomass for internal industrial energy gains. • Wet briquettes (20 wt% and 50 wt%) production was technically feasible. • Briquettes with added heat (150 °C) exhibited superior properties. • All biomass briquettes exhibited improved energy potential. • Hydrochar briquettes showed superior energy content and durability. [ABSTRACT FROM AUTHOR]

Motivated by large oil price swings, high economic and geopolitical uncertainties, and the financialization of oil, this paper examines the frequency spillovers and co-movements between oil shocks (risk and demand) and the stock markets of top oil-producer and consumer countries, namely, Canada, China, Russia, Saudi Arabia, and the US. The analysis uses the time-domain spillover index of [1], the frequency-domain spillover of [2]; and the wavelet coherence approach. The findings reveal that spillovers run from the U.S., Canada, and, to a lesser extent, Russia to oil shocks. On the other hand, oil shocks, Saudi Arabia, and China constitute net receivers of shocks. The intensity of spillovers is heavier in the short-term frequency than in the intermediate- and long-term. Furthermore, the direction of spillovers is more defined in the long-term. The U.S. stock market exerts a strong impact on oil risk in general, but the impact is stronger in the short-term. Conversely, an oil demand shock is susceptible to innovations from Canada and Russia that are stronger in the long-term. This means that oil risk shock stemming from innovations in financial markets is short-lived and dissipates quickly due to quick reactions from market participants. On the contrary, long-term links characterize the relationship between oil demand shock and financial markets, mirroring the macroeconomic nature of the linkages. Finally, while the 2008 crisis, EDC, oil price crash, and the COVID-19 pandemic coincided with strong spillovers in the short-term, the COVID-19 era was marked by higher spillovers in the long term. The findings provide important information for investors and policymakers in terms of diversification, risk management, and efforts to mitigate contagion. • This paper examines the frequency spillovers and co-movements between oil shocks and the stock markets. • We use the time-frequency spillover index method and the wavelet coherence approach. • Spillovers run from the U.S., Canada, and, to a lesser extent, Russia to oil shocks. • Oil shocks, Saudi Arabia, and China constitute net receivers of shocks. • The intensity of spillovers is heavier in the short-term frequency than in the intermediate- and long-term. [ABSTRACT FROM AUTHOR]

Extensive research exists on the potential impacts of foresight; however, a comprehensive understanding of the factors that lead to foresight impact, particularly in influencing senior management decisions, is relatively sparse. This study addresses this by reporting on a Delphi and expert panel involving eight senior Canadian government foresight program leaders. These leaders were asked to help identify and then rate a list of factors that they felt resulted in their foresight projects impacting senior management decisions. Results suggested that factors such as foresight methodology, while leading to good foresight, do not necessarily result in senior decision-maker impact. Instead, criteria defined in this paper as the "consultants' toolkit," such as understanding the senior decision maker's pain points and foresight managers having a strong understanding of the organization's inner workings, play a crucial role. The expert panel discussion suggested that the importance of senior management decision-making factors depends on three mediating variables: The temporal orientation of the Department, the foresight orientation of the department's senior management, and the nature of the relationship between the foresight manager and the senior decision maker. • Paper identifies factors that lead to senior management accepting and implementing the results and recommendations of foresight projects. • A two round Delphi and expert panel was held as part of this study with eight senior Canadian government foresight program leaders • Managers identified factors that relate more to a consultant tool kit than foresight methodology that results in decision impact foresight. • A contingency model is presented with three elements which the impact factors importance • The paper highlights the importance of research partnerships that include both academics and practitioners [ABSTRACT FROM AUTHOR]

This paper explores the perceptions and future imaginaries of a group of union members in Manitoba, Canada, concerning climate change, energy transition, and the roles of unions and workers in climate politics. Based on interviews with 30 rank and file workers carried out through the winter of 2020, the results suggest some starting points for a more active engagement between the labour movement and climate politics—an engagement that is central to climate justice, and that becomes more vital every moment as workers both participate through their waged labour in the production of ecological crisis, and stand to suffer intensely from both climate change and from elite-led energy transitions. • Unionized workers broadly agree with the characterization of "climate emergency." • Participants connect to climate change through expanded spatial and temporal considerations. • There is broad agreement that climate change is a key consideration in unions' protective role. • Union workers' future imaginaries of energy transition do not frequently engage with "system change" narratives. • Union workers characterize transition as something done to, rather than by, workers. [ABSTRACT FROM AUTHOR]

Toponyms contain Indigenous modes of understanding and reflect ecological histories and deep relationships between Indigenous communities, arctic environments, time, and land. Completed toponymic studies are useful for researchers to access; however, they are notoriously difficult to find. Many are completed by community groups and published on their websites, or are completed by government agencies and published as grey literature. An inventory of toponym projects has not existed, and eliciting what has been completed where, with whom, and by whom has required long searches through academic and grey literature. In this paper, we inventory Indigenous toponymy projects in the Canadian North, and document our efforts to produce a publicly accessible index where toponymy projects can be found via maps. New or unknown resources can be added by users. Our purpose, here, is to document the production of this resource and to increase awareness of toponymical resources among communities, researchers, scientists, and other stakeholders. We reflect on knowledge gained through construction of the index and make observations on trends in Inuit toponym research through time. We argue for renewed efforts across arctic sciences to recognize Inuit-environment relationships through reference to place names and the ecological histories they encapsulate, and we provide considerations for future work. • Inventory of Indigenous place names projects in arctic Canada. • Accessibility of knowledge through online interactive map. • Use of ESRI Experience Builder to make toponymy projects publicly searchable. [ABSTRACT FROM AUTHOR]

The monitoring of forest ecosystems is significantly affected by the lack of consistent historical data of low-severity (forest partially disturbed) or gradual disturbance (e.g. eastern spruce budworm epidemic). The goal of this paper is to explore the use of a subset of Landsat time series and deep learning models to identify both the type and the year of disturbances, including low-severity and gradual disturbances, in the boreal forest of eastern Canada at the pixel level. Remote sensing data such as the spectral information from Landsat time series are the best available option for large scale observations of disturbances that go back decades. Traditional modeling approaches, like LandTrendr, require substantial handcrafted pre-processing to remove noise and to extract temporal features from the image sequences before using them as input to a classical machine-learning model. Deep-learning models can autonomously discern which features are relevant within the coarse temporal and spectral information from the Landsat annual dense time series. We evaluated the performance of TempCNN and Transformer model in detecting and classifying the type and the year of the forest disturbance using Landsat time series subsequences. Our findings resulted in the generation of four disturbance maps outlining the forest history from 1986 to 2021 within the eastern Canadian boreal forest. Our experimental outcomes demonstrate several significant benefits of employing deep learning models. Firstly, using noisy Landsat time series they achieve comparable accuracy for classifying fire and total harvesting than existing publicly available disturbance maps. Secondly, the use of shorter time series subsequence with deep learning models enables to map adequately different overlapping disturbances occurring in the complete time series. Finally, they increase the number of distinguishable disturbance classes by adding partial harvesting, gradual disturbances, and forest recovery from older events, making them useful approaches for obtaining the first remote sensing-based map for areas affected by the eastern spruce budworm. • TempCNN, Transformer tested on Landsat time series for disturbance classification. • The type and the year of disturbance events were classified with good accuracy. • Deep learning effective for identifying partial and progressive disturbances. • Landsat subsequences extract overlapping disturbances. [ABSTRACT FROM AUTHOR]

This paper investigates the relationships among the important process parameters that impact Post-combustion Carbon Capture (PCC) carbon dioxide (C O 2) separation. A better understanding of the complex relationships among those parameters can support optimization and performance enhancement of the separation process. Being able to precisely predict the process parameters will enable the operator to determine the current state of the process, forecast any potential changes or events, and adjust process parameters to enhance the plant's performance. With the objective of studying the process parameters' correlations in the amine-based PCC process, we modeled the multi-year historical production data of the Clean Energy Technologies Research Institute (CETRi) (formerly known as the International Test Center for PCC or ITC) in Regina, Saskatchewan, Canada, using a Decision Forest approach. The model validation process revealed that the Decision Forest model produced higher predictive accuracy than previous efforts. The Decision Forest models we developed also represent knowledge about the importance of parameters involved in the capture process, and such knowledge is useful for further optimization of the capture process in the future. • Modeling the parameters of the Carbon Capture process with machine learning (ML). • The ML models used Decision Forest with Gradient Boosting and Oblique Split. • The ML models achieved superior predictive accuracy compared to past efforts. • The ML models support interpretability by visualizing weights and prediction paths. [ABSTRACT FROM AUTHOR]

As part of the response to Canada's worsening overdose crisis driven by a toxic, adulterated drug supply, there has been increased attention to and expansion of drug treatment, options, including injectable opioid agonist treatment (iOAT). iOAT typically involves the, witnessed daily injection of opioids under healthcare provider supervision. There is a robust, evidence base on iOAT; however, there has been less focus on how people engage with this; treatment outside of clinical trials. This paper examines how people engage with iOAT programs, in expanded treatment settings in Canada, focusing on how the broader socio-structural context, shapes patient subjectivities in treatment. This study draws on critical ethnographic and community-based research approaches, conducted with people accessing four iOAT programs in Vancouver's Downtown Eastside; neighbourhood from May 2018 to November 2019. Data included in-depth baseline and followup, interviews and approximately 50 h of observation fieldwork conducted in one iOAT, program and with a subsample of participants in the surrounding neighbourhood. Analysis, leveraged the concepts of biological citizenship and structural vulnerability. This analysis characterized three narrative frames— regular long-term engagers, pain, patients, and sporadic and short-term engagers —through in-depth case presentations of participants with distinct types of engagement with iOAT programs. Participants within these, narrative frames described a dominant form of iOAT citizenship, an autonomous patient who, regularly engages in treatment and avoids pleasure. However, structural vulnerabilities, including, homelessness and housing instability, entrenched poverty, criminal-legal system engagement, and unmanaged pain, shaped the ability of participants to make claims to this normative model of citizenship. This study examined how structural vulnerabilities impact people's construction and ability to make iOAT citizenship claims. Findings point to the need for changes within and outside of iOAT programs, such as lower threshold treatment models, improved social services (e.g., secure housing), and pain management support. • Biological citizenship used to examine how people engage with iOAT. • Narrative frames used to explore patterns of iOAT engagement. • These served as alternate to iOAT citizenship framed by treatment. • Unmanaged pain, housing instability, and poverty impacted treatment engagement. [ABSTRACT FROM AUTHOR]

Geothermal systems installed at intermediate depths (∼1–2 km) in sedimentary basins represent an attractive option to provide low-carbon heat in cold countries, even where the geothermal gradient is low, using either closed- or open loop systems combined with heat pumps. However, the installation of such systems is costly and risky due to the uncertainty associated with the geological, hydrogeological and thermal properties of the targeted unit(s). Additionally, the performance of different types of systems is seldom compared in the literature for a given geological context. This paper presents a numerical approach to readily assess the maximum energy that could be produced by different geothermal systems (a deep borehole heat exchanger (DBHE) and three types of doublets) and compare their performance for preselection purposes. Since deep formations are often poorly characterized, the sensitivity of these systems to the most impactful site properties is evaluated. For each scenario of site properties, the systems were simulated for different operation flow rates. The maximum usable flow rate is determined from simulation results. The flow rate maximizing net energy production is used for the DBHE, while the maximum flow rate ensuring safe injection pressure has been selected for the doublets. The heating power produced per length drilled and system COP are calculated for each simulation and interpolated for the maximum usable flow rate to fairly compare the systems' performance. An illustrative case using the Bécancour area (eastern Canada) highlights that, even if the site stratigraphy and properties have been relatively well characterized previously, uncertainty regarding key properties significantly affects simulation results and, consequently, the choice of the geothermal system to install. Our numerical approach is intended as a decision-making aid in order to properly plan the installation of these expensive systems. [Display omitted] • New method for pre-selecting 1–2 km geothermal systems and assess heating potential. • Compares the DBHE and geothermal doublet performances for various designs. • Includes a sensitivity analysis to permeability, thermal conductivity and heat flux. • Determines the maximum usable flow rate for each system and scenario. • An application demonstrates the need to consider the uncertainty of rock properties. [ABSTRACT FROM AUTHOR]

This paper mainly discusses exponential synchronization of nonlinear CDN via intermittent pinning control on T. By using Lyapunov and time scales theory, a novel sufficient condition to guarantee the synchronization of CDNs is obtained. The method of intermittent pinning control is adopted in designing controllers to ensure the realization of synchronization of CDNs. Unlike most existing results, our results are an extension of previous results, integral delay and coupling disturbance are considered in the time-delay nonlinear CDNs. Therefore, our results are less conservative but more persuasive. Moreover, our model can be applied not only to continuous/discrete CDNS, but also to mixed CDNs. Finally, we give numerical simulations to demonstrate the feasibility of our theory. [ABSTRACT FROM AUTHOR]

The suburbanization of poverty has been a concerning trend in many urban regions. While research has described patterns of suburbanization of poverty at regional and neighbourhood levels, there are open questions about how lower-income households have agglomerated in the suburbs in recent history. Is suburban poverty primarily a result of 1) the movement of low-income residents from central to suburban neighbourhoods (e.g., via processes of gentrification and displacement), 2) migration between Census Metropolitan Areas and the immigration of low-income groups to suburbs, or 3) becoming and remaining poor while staying in the suburbs? The objective of this paper is to describe and quantify the propensity of these predominant individual geographic pathways to suburban poverty. We do so via a cluster analysis of census and land use data to define neighbourhoods as either central or suburban, and then link this categorization to a large-scale panel dataset representing 20 % of tax filers in Canada (from 2006 to 2016). These data allow for analyzing different pathways within the context of large Canadian metropolitan areas, specifically to what extent poverty in suburban neighbourhoods stems from intra-urban residential mobility, immigration, and becoming poor in-place. We find that becoming and remaining poor while staying in the suburbs encompasses a greater proportion of suburban poverty than immigration and centre-to-suburb residential mobility combined. Overall, this research expands our understanding of the sources of suburban poverty while also providing pertinent information to aid preventative policy aimed at reducing suburban poverty in Canada. • The largest source of suburban poverty in Canada is from getting poor in place. • Immigrants to Canada face the highest risk of becoming part of the suburban poor. • Migration from more accessible parts of the city represents a small share of suburban poverty growth. [ABSTRACT FROM AUTHOR]

The global call to address climate change and advance sustainable development has created rapid growth in research, investment, and policymaking regarding the renewable energy transition of Indigenous communities. From a rightsholder perspective, Indigenous Peoples' vision of sustainability, autonomy, and sovereignty should guide research on their energy needs. In this paper, we present a multi-method, inductive examination to identify gaps between Indigenous communities' expressed needs and rights, and the questions researchers and policymakers investigate in energy transition research conducted in the context of Indigenous communities located in Canada. We combine a systematic review of the extant literature, a scoping review of the grey literature on off-grid communities by Indigenous and non-Indigenous governments and non-governmental policy bodies, qualitative primary data collected via fieldwork, and an in-depth study of an Indigenous-led renewable energy transition study conducted by Haíɫzaqv Nation's Climate Action Team. We holistically examine these different perspectives and identify emergent themes to recommend ways to bridge the gaps between off-grid renewable energy research and stated Indigenous community priorities. Specifically, we recommend designing equitable research practices, understanding community worldviews, developing holistic research goals, respecting Indigenous data sovereignty, and sharing or co-developing knowledge with communities to align with community priorities closely. • There is a research-practice gap in Indigenous communities' energy transitions. • We used a multi-method inquiry integrating Indigenous and Western approaches. • Renewable energy literature diverges from the Indigenous community vision and goals. • Indigenous research methods can reduce the research-practice gap in high-tech fields. • Community-based approaches can use traditional laws to yield actionable outcomes. [ABSTRACT FROM AUTHOR]

Community renewable energy is increasing globally, but many northern and remote Indigenous communities remain energy insecure. Community appropriate sustainable energy solutions requires more than building renewable energy projects – it requires local socio-technical capacity to design, implement, and maintain renewable energy projects. Yet, notwithstanding advances in renewable energy technology there is limited understanding of the socio-technical capacity of northern and remote Indigenous communities to engage in energy transitions. Based on a review of energy transitions scholarship and northern contexts and informed by a workshop engaging northern and Indigenous community members from Canada and Alaska, this paper presents foundational pillars for assessing the socio-technical capacity needs of communities to pursue and sustain local energy transitions. These pillars are inter-dependent and emphasize the importance of local energy champions and inter-local energy networks to enable innovation and capacity building; community values that articulate immediate and longer-term goals for energy transition, including the social and economic opportunities to be realized by a more sustainable energy system; community knowledge of local energy resources, technologies, and opportunities, and embedded skills to support transitions; and the skills innovation to pursue and manage new energy systems, coupled with youth engagement as future community energy leaders. The proposed framework is intended to support the early stages of community energy transition planning. • Energy transition in remote communities involves more than building new projects. • Socio-technical capacity is critical to renewable energy security in remote off-grid areas. • Seven pillars are proposed to guide local capacity assessment for community energy. • Renewable energy in remote communities means self-sufficiency and self-determination. [ABSTRACT FROM AUTHOR]

Shipping in the Canadian Arctic has a long history, encompassing diverse maritime pursuits, ranging from traditional Inuit subsistence practices to European exploratory expeditions, whaling, and fur trading. The escalating impacts of climate change in the Canadian Arctic have created ample opportunities for Arctic shipping activities related to fishing, cruise tourism, resource (mineral) transportation, research, and government services. Nowadays, the necessity of developing a sustainable economy, the need for environmental protection, and the imperative of reconciliation with Indigenous Peoples present considerable challenges for the Canadian government in regulating Arctic shipping. To comprehend the contemporary issues of Arctic shipping governance, this paper conducts an overview of the history of Arctic shipping activities in Canada and reviews Canada's diverse policies and laws that have been instituted to govern Arctic shipping. Drawing upon the analysis of these policies, the article advocates for a collaborative governance framework to cope with the multifaceted challenges confronting the governance of Arctic shipping in Canada. Such a framework ought to prioritize enhancing cooperation, integrating unilateral and multilateral policies and laws, respecting the rights of Indigenous Peoples, and involving Inuit in Arctic shipping governance. [ABSTRACT FROM AUTHOR]

• New carbon-sequestration geosystem paradigm proposed for screening CO 2 repositories. • Deposition, burial history 1st-order controls on repository attributes, traps, etc. • Genetic understanding of geology enables property prediction away from data control. • Case-study application to heavily industrialized region of onshore Canada. In this paper, I propose a new geoscience paradigm for evaluating potential carbon-sequestration targets. I introduce the term carbon-sequestration geosystem to study and describe portions of sedimentary basins where all the geologic components necessary for the safe and long-term storage of CO 2 are present. The purpose of this type of analysis, most appropriately applied at a basin-screening stage, is to derive a holistic, genetic, and predictive understanding of the geology – the depositional systems, structural setting and other factors that are direct controls on storage, injectivity, potential for induced seismicity, and other critical factors. To illustrate the concepts, I present a re-evaluation of the geologic carbon-sequestration options in Southern Ontario (Canada) where business and environmental needs, mostly associated with hard-to-abate industries, require urgent action. Legacy wireline-logs, core, and outcrop data are the main data sources available in this onshore setting. The results of this new, independent study are broadly similar to those of previous studies: the Cambrian section, a saline aquifer, is the most likely candidate to be a CO 2 repository. However, the methodology used identified several issues (e.g., stratigraphic heterogeneity, proximity to basement) that will need addressing by targeted data collection and/or analysis before site-selection for a test should be undertaken. [ABSTRACT FROM AUTHOR]

The northwest coast of North America exhibits highly variable patterns of relative sea-level (RSL) change following the Last Glacial Maximum (LGM) that reflect proximity to the Cordilleran glacial ice loading and local rates of deglaciation. In this paper we present postglacial RSL histories for four coastal zones in a transect across northern Vancouver Island, Canada, derived from multiple proxies (isolation basin cores, geological exposures, archaeological sites, GIS-based landform interpretation), and relate these to the timing of glacial retreat after the LGM. Notably, parts of the west coast of northern Vancouver Island were ice-free by ∼18,200 years ago, earlier than much of the rest of Vancouver Island and the broader region. These four RSL reconstructions demonstrate substantial variation across the north end of Vancouver Island, which we attribute to regional differences in glacial isostatic processes. Additionally, some RSL curves reveal the likely effects of global glacial meltwater pulses. Documenting late Pleistocene and early Holocene coastline change in this region of Vancouver Island is significant for understanding the late Quaternary history of western North America more broadly: the RSL histories help delimit potential refugia and postglacial expansion of plants and animals (including humans) as the ice retreated. • We present four new relative sea level curves for Northern Vancouver Island, Canada. • RSL histories vary from east to west, related to glacio-isostatic processes. • Radiocarbon ages constrain timing of glacial retreat, landscape change. • Some parts of northern Vancouver Island have been ice-free for ∼18,200 years. • Past shoreline positions help understand postglacial expansions of plants/animals. [ABSTRACT FROM AUTHOR]

Permylene™ demonstration system (PDS), a membrane-based pilot unit for olefin/paraffin separation, is designed and fabricated by Imtex Membranes Corp. (Imtex). The PDS, equipped with pilot-scale Permylene™ elements, is capable of treating up to 3 kg/h of olefin/paraffin mixture. The PDS unit is installed in Imtex's testing lab in Mississauga, Ontario, Canada. Various plant-collected and lab-blended olefin/paraffin mixtures involving ethylene/ethane (C2), propylene/propane (C3), and butene/butane (C4) have been assessed on the unit. This paper is focused on the application of PDS for C3 separation, and a series of remarkable performances that have been achieved by the Permylene™ membrane and PDS unit. Propylene purity of over 98.5 vol% in the permeate/product stream has been reached over a wide range of propylene recovery rates, which could offer significant flexibility to meet various industrial operation conditions. Furthermore, the PDS unit demonstrates its stability and efficiency with 1200 hrs of continuous C3 permeation. Finally, a case study of recovering 90 % of propylene from 15,000 kg/h of C3 is performed to estimate energy consumption in commercial applications. The energy consumption of the Permylene™ process is calculated and compared with that of the distillation process. The result indicates that the energy consumption in PDS is extremely low, equal to only 8 % of that required in distillation. The study undeniably validates Permylene™'s remarkable capability for C3 separation, highlighting its potential as a viable and energy-efficient alternative to traditional distillation. [Display omitted] • The asymmetric membrane and solution replenishing overcome the instability. • This pilot unit is capable of treating up to 3 kg/h of olefin/paraffin mixture. • Propylene purity of 98.5 vol% is reached over a wide range of recovery rates. • Stable performance is shown in 1200 h of continuous C3 permeation. • The energy consumption in PDS equals 8 % of that required in distillation. [ABSTRACT FROM AUTHOR]

The literature on professional socialization focuses on how students adopt and internalize professional identities and values, and assumes that boundary work is essential to learning how best to practice their profession. However, a focus on boundary work in the context of midwifery training - which is embedded in the gendered and hierarchical landscape of maternity care - is lacking. Thus, this article examines how Canadian student-midwives learn to navigate and negotiate interprofessional boundaries. Grounded in a symbolic interactionist approach, it draws on 31 semi-structured qualitative interviews from a mixed-methods national study on midwifery retention, explores how midwifery students make sense of the tensions among midwives, physicians, and nurses, and describes what strategies they utilize when navigating boundaries. Our analysis, based in constructivist grounded theory, revealed that participants learned about interprofessional tensions in clinical placement encounters via direct or indirect interactions with other healthcare professionals, and that strategies to navigate these tensions included educating others about midwifery training and adopting a learner identity. This article proposes that the process of professional socialization enables to reshape professional boundaries and that students are not only learners but also agents of change. These findings may yield practical applications in health education by highlighting opportunities for improving interprofessional collaborations. • Boundary work is part of professional socialization process. • Professional boundaries are ambiguous in midwifery but they are understudied. • This paper examines boundary work among 31 Canadian midwifery students. • The boundaries were clear with physicians but blurred in communication with nurses. • Learning about boundaries, students recreated them but also became agents of change. [ABSTRACT FROM AUTHOR]

The fate of the carbon stored in frozen peatlands in Canada's Hudson Bay Lowlands (HBL) depends strongly on water, with wetter conditions favoring long-term storage. Dynamic surface water products generated from historical Landsat data exist to inform surface water trends in the HBL based on binary classifications of land vs water at 30 m spatial resolution. However, the HBL contains many water features smaller than 30 m, including streams and patterned fens that require a sub-pixel mapping approach to fully capture their dynamics. In this paper, we leverage an existing binary dynamic surface water product to generate a spatially and temporally comprehensive Landsat sub-pixel surface water time-series over the HBL. We first generate Landsat Red, NIR and SWIR composites from 1985 to 2021 and evaluate data-driven machine learning and physical models to derive sub-30 m water fractions across the entire mapping domain. Data-driven models were calibrated on 30 m water fractions obtained from 16 of 17 WorldView scene water fraction maps and assessed on the 17th held-out scene in a jackknife validation. Data-driven models were also calibrated by relating scaled Landsat reflectance to water fractions obtained from binary water masks at corresponding scales from 90 to 270 m. Physical models involved simple linear unmixing using a new approach that samples land endmembers in the vicinity of each pixel to represent land reflectance, and a global water endmember sampled beneath permanent water in each image. The assumption of linear scaling was verified at sub-30 m to 270 m resolution for NIR, SWIR and NDVI, which were all highly correlated with water fraction and had no significant differences among water fraction – spectral feature relationships across the full range of scales. Each of 11 different methods and input spectral features were evaluated against WorldView water fractions and ranked based on nine criteria. We found that machine learning using all spectral features including local NIR land endmembers performed best among data-driven approaches, and linear unmixing of the NIR band using local land endmembers performed best among physical. Both best-performing methods were applied to the entire time-series and surface water area trends were calculated and compared with trends obtained from binary water masks. All three methods agree on the direction of surface water change towards wetting, with sub-pixel inter-annual variation agreeing with stream discharge noted in other studies. • Physical and data-driven Landsat water fraction methods tested in the Hudson Bay Lowlands. • Physical methods perform linear unmixing between local land and global water endmembers. • Data-driven methods consist of machine learning calibrated using high-resolution water. • Best methods applied to 1985–2021 Landsat time-series reveal overall wetting trends. • Spatial trends generally suggest drying in bogs and wetting in fens. [ABSTRACT FROM AUTHOR]

Reliable construction project cost estimation relies on accurate quantity takeoffs (QTOs), traditionally done with error-prone 2-D drawings, but the emergence of Building Information Modeling (BIM) has improved QTO speed, accuracy, and reliability. However, the quality of BIM models can influence quantity accuracy, an aspect often overlooked in research on automating QTO with BIM. This paper develops an integrated framework to automatically extract and visualize construction quantities from BIM models. The system includes a Quantity Precision Check (QPC) module for automating more accurate QTO outputs. These outputs are then automatically transferred to an external database and visualized through a user-friendly dashboard on the Microsoft Power BI platform. This dashboard allows for comparisons between 2-D and BIM quantities and helps track changes in quantities over time due to design changes. The system was successfully validated in an infrastructure construction project in Canada, where it identified a 39% inconsistency in wall elements' material quantities and reduced steel quantity by 10% due to design changes. Overall, the system offers a speedy, reliable, and efficient tool for construction estimators, site managers, and cost control teams to provide accurate quantities to the procurement team and make swift decisions in response to design change impacts on construction costs. • This study introduces an automated QPC/QTO system for architectural and structural BIM models. • A QPC/QTO system workflow was developed to automatically calculate their quantities and check their accuracy in the BIM model. • The Data Extraction and Analysis Module was developed to automatically calculate, and check the accuracy of the quantities of each category. • The Data Visualization Module was developed to visualize the final QTO results and inconsistencies in BIM parameters after each update. • The system can be used as a fast and reliable tool for construction estimators to provide accurate quantities to the procurement team. [ABSTRACT FROM AUTHOR]