Search

The operation of solar photovoltaic installations for many years may lead to problems such as reduced energy efficiency and aging of components. Under this framework, replacing certain components in the facility to extend the service life of the power plant is viewed, in some cases, as a feasible strategy. However, despite its enormous strategic interest for the solar PV industry, we find that revamping PV installations has been the focus of very few scientific publications, and even less so when it comes to analyzing real facilities. Thus, this paper performs a techno-economic analysis of three revamping strategies at a real PV power plant located in the south-east of Spain. The strategies consist of substituting, in each case, the PV modules, the inverter, and both components. The simulated results show that the highest production value by installed power is obtained when both the modules and the inverter are replaced. In the same vein, the economic analysis reveals this scenario as the most favorable in terms of profitability. Based on the results obtained, an interesting future line of research would be focused on the extension of the analysis at country level to study the joint impact of numerous revamping actions. • Techno-economic analysis of revamping projects of a real solar PV power plant. • Replacing modules and inverter emerges as the most feasible strategy. • Study's applicability extends to other revamping initiatives and geographical regions. • Economic outcomes allow the most cost-effective alternatives to be determined. • This research can contribute to efficient and sustainable energy planning. [ABSTRACT FROM AUTHOR]

• We present a novel integration for reducing CO 2 emissions in blast furnaces. • It combines top gas recycling, oxy-fuel regime, power to gas and biomass pyrolysis. • The integration was modelled using the extended operating line methodology. • The best performance was found for pyrolysis at 700 °C. • The CO 2 emissions were reduced by 58% (9.8 MJ/kg CO2 energy consumption) The paper introduces a novel approach for mitigating CO 2 emissions in blast furnaces by integrating top gas recycling, an oxy-fuel regime, power to gas, and biomass pyrolysis. Various case studies were conducted, involving the adjustment of pyrolysis temperatures (300 °C, 500 °C, 700 °C, and 900 °C) and varying the quantity of blast furnace gas directed to methanation for carbon recycling. Pinus radiata, abundant and cost-effective in Chile and Spain, was chosen as the biomass source. The integration was modeled using the extended operating line methodology and evaluated through 12 key performance indicators, such as flame temperature, coke consumption, CO 2 emissions, and specific primary energy consumption per unit of CO 2 avoided. Optimal performance was observed with pyrolysis at 700 °C and no blast furnace gas recycled through methanation. This configuration achieved a 58 % reduction in CO 2 emissions, with an energy consumption of 9.8 MJ/kg CO2 , and obviated the need for geological storage. Comparing this innovative proposal with other oxygen blast furnace approaches from the literature revealed a 13 percentage point improvement in CO 2 reduction over the second-best alternative. Additionally, the required electrolysis capacity, influencing capital expenditure, was 57 % lower, and energy consumption was reduced by 44 %. [ABSTRACT FROM AUTHOR]

This paper presents a model for optimizing the life cycle economic and environmental impacts of a hybrid renewable energy and battery storage system – as energy supply technologies (EST) for off-grid farms. Micro-hydropower and photovoltaics represent the primary renewable energy (RE) sources, with batteries and a diesel generator considered as possible back-up systems. A modified Non-dominated Sorting Genetic Algorithm II (NSGA-II) was developed and applied to a case study farm in Southern Spain and provided different EST solutions to optimize a design based on economic (life cycle costing or LCC) and environmental (life cycle assessment or LCA) constraints. The results highlighted that cases with a strong dependence on batteries could achieve minimum costs and lower impacts for climate change and energy resources (non-renewable fuels). In contrast, the optimal system for minimizing the consumption of material resources (metals/minerals) resulted in higher fuel use, which was up to 25% more expensive. The optimal EST solutions used up to 37% of the total energy generated; however, the results were sensitive to energy production-demand distributions. This methodology can help identify the most cost-effective solutions with the lower environmental impacts for decarbonizing the agricultural sector. [Display omitted] [ABSTRACT FROM AUTHOR]