Search

Due to the development of the petroleum industry, more severe mining conditions put forward higher corrosion resistance requirements for materials. In this paper, the corrosion resistance and corrosion behavior of four TC4-xNi-yNb (x, y = 0, 0.5) alloys were investigated in a 1 mol/L HCl solution through microscopic characterization, electrochemical tests and corrosion weight loss testing. The results demonstrated that the addition of Ni and Nb elements could improve the corrosion resistance of TC4 alloy to varying degrees. The addition of niobium formed niobium oxide in the passive film, while the addition of nickel thickened the passive film without formation of nickel oxides. The improvement of corrosion resistance of TC4 by nickel is more significant. Finally, a new highly corrosion resistant alloy TC4-0.5Ni-0.5Nb is preferred. [ABSTRACT FROM AUTHOR]

Titanium alloy coiled tubing (CT) has great superiority while operating in deep wells with severe conditions, but it faces serious challenges during roll forming like high springback, edge cracking and surface wearing. In order to utilize the high precision and high efficiency production of titanium alloy CT, it is urgently necessary to develop a detailed process design. Based on the W-forming strategy and the cubic curve of the strip edge projection, the flower pattern and roll design for the 21-pass roll forming process were completed. Different tube dimensions and roll positionings were researched regarding the aspects of contact state, stress–strain distribution and geometry ovality using numerical simulation. The thickness/diameter ratio of the tube that can be formed should be within an effective range: exceeding the range leads to edge cracking, and an insufficient ratio leads to high springback. Roll positioning significantly affects the contact state and stress distribution, but leads to no major differences in the tube geometry. Finally, the trial production of the TA4 titanium CT with a size of Φ50.8 × 4 mm was completed successfully and was consistent with the simulation results. [ABSTRACT FROM AUTHOR]

A systematic study was conducted on the impact of annealing treatments on the microstructure and properties of cold-rolled Ti50Ni47Fe3 alloys using optical microscopy, scanning electron microscopy, electron backscattered diffraction, and an electronic universal testing machine. It was found that, during low-temperature annealing (400 °C and 500 °C), the annealing time had no significant effect on the microstructure or properties of the Ti50Ni47Fe3 alloy. Only elongation (δ) increased with the increase in the annealing time, and the grain orientation of the Ti50Ni47Fe3 alloy was <111>//RD (rolling direction). When annealing at medium–high temperature (600 °C), as the annealing time increased, recrystallization and grain growth processes occurred, resulting in a continuous decrease in strength and an increase in δ. Meanwhile, it was found that the grain orientation of the cold-rolled Ti50Ni47Fe3 alloy changed from <111>//RD during the recovery and recrystallization processes to <101>//RD after the grain growth process. The orientation distribution function cross-section φ2 = 45° results indicate that the texture was mainly distributed along the γ orientation line (φ1 = 0~90°, Φ = 54.7°, φ2 = 45°). When annealed at 400 °C and 500 °C, the texture of the Ti50Ni47Fe3 alloys was (111)[uvw]. When the annealing treatment was 600 °C for 120 min, a (110)[uvw] texture occurred. Additionally, ductile fracture occurred in all specimens, and the crack origin was located on one side of the fracture surface, with obvious "Y"-shaped propagation. This article studied annealing treatments of cold-rolled Ti50Ni47Fe3 alloys, providing corresponding theoretical guidance for subsequent production applications. [ABSTRACT FROM AUTHOR]

2-(3-Bromophenyl)-1-(4-morpholinyl)ethanone belongs to one of morpholine derivatives. In this paper, 2-(3-bromophenyl)-1-(4-morpholinyl)ethanone was synthesized by a two-step synthesis method. In order to determine the structure of the target compound, FT-IR,1H NMR,13C NMR and MS were used for detection. Meanwhile, X-ray diffraction was used to detect the single crystal and obtain the crystal structure data of the target compound. The molecular crystal structure was compared with that determined by density functional theory. The frontier molecular orbitals and molecular electrostatic potential energy were used to further study the physical properties of the compounds. [ABSTRACT FROM AUTHOR]

The evolution of the microstructure and hardness changes in the Au-15Ag-12Cu-6Ni alloy during the processes of cold rolling and annealing were investigated and the heat treatment regimen for the alloy was optimized in this article. The hardness of the alloy continuously increases with the cold rolling reductions, leading to continuous deformation of the grains during the cold rolling process, ultimately resulting in smaller grain sizes. Subsequent annealing induces recovery and recrystallization, achieving complete recrystallization at 700 °C. An intriguing softening effect is observed after annealing at 700 °C, manifesting in a significant reduction in hardness to 238 (Hv0.5). The cold deformation texture of the alloy aligns with the recrystallization texture type, exhibiting only a certain degree of angular deviation. This is primarily characterized by <111>//RD texture and a texture deviating 60° from RD towards TD. The performance of the finished sheet improves with the precipitation of ordered phases AuCu after a 300 °C heat treatment for 0.5 h, resulting in a remarkable hardness of 380 (Hv0.5). [ABSTRACT FROM AUTHOR]