Search

A single-stage phosphorylated polyvinyl alcohol immobilized-cell reactor with three operation modes was employed to investigate the efficiency of simultaneous carbon/nitrogen removal from raw swine wastewater. In continuous aeration mode, the removal efficiency of chemical oxygen demand (COD) and total nitrogen (T-N) exceeded 70 and 8%, respectively, at hydraulic retention time of 10 days. In intermittent aeration (IA) mode, the removal efficiency of COD and T-N was more than 85 and 46%, respectively, when the reactor was set at 50% aeration duration to cycle time to operate at three aerobic-anoxic cycles per day. When oxidation-reduction-potential control was adopted to control the duration of the anoxic period in the real-time controlled (RTC) IA mode for a 4 h aeration period, the total cycle time was reduced by about 20% with a slight increase in removal efficiency of COD (87%) and T-N (47%). The system with no extra chambers required is efficient in simultaneous carbon/nitrogen removal. DOI: 10.1061/(ASCE)0733-9372(2006)132:3(423) CE Database subject headings: Simulation; Abatement and removal; Carbons; Nitrogen; Wastewater management; Reactors.

In this article, we report the development of the fast incorporation of primary amine functional groups into a polylactide (PLA) surface using the post-discharge jet region of an atmospheric-pressure nitrogen-based dielectric barrier discharge (DBD). Plasma treatments were carried out in two sequential steps: (1) nitrogen with 0.1% oxygen addition, and (2) nitrogen with 5% ammonia addition. The analyses show that the concentration of N/C ratio, surface energy, contact angle, and surface roughness of the treated PLA surface can reach 19.1%, 70.5 mJ/m2, 38° and 73.22 nm, respectively. In addition, the proposed two-step plasma treatment procedure can produce a PLA surface exhibiting almost the same C2C12 cell attachment and proliferation performance as that of the conventional gelatin coating method. Most importantly, the processing/preparation time is reduced from 13-15 h (gelatin coating method) to 5-15 min (two-step plasma treatment), which is very useful in practical applications. © 2013 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 102A: 160-169, 2014. [ABSTRACT FROM AUTHOR]

In this paper, we demonstrate that, by adding a small amount of \CF4 (2\%) into a compressed-air planar dielectric barrier discharge (DBD), one can effectively inactivate a B. subtilis spore up to 50 mm in width in the postdischarge jet region after ten passes of exposure of plasma plume (equivalent plasma exposure time of 1 s) for treatment distance of up to 14 mm for the spore concentration in the range of 10^5-10^7 CFU/mL. A possible mechanism is proposed, i.e., the chemically active F atoms and \CFn\ ({n} = 1 - 3) are generated through the help of abundant excited nitrogen molecules in the postdischarge region. [ABSTRACT FROM PUBLISHER]

Abstract: The fermentation of Grifola frondosa was investigated in the shake flasks and a 5-L jar fermenter in batch and fed-batch modes. In the shake-flask experiments, the preferable mycelial growth and exopolysaccharide (EPS) production was observed at relatively low pH; maltose and glucose were preferred carbon sources for high mycelial production. The EPS was doubled after 13 d of cultivation when glucose was increased from 2% to 4%. Yeast extract (YE) (0.4%) in combination with corn steep powder (CSP) (0.6%) and YE (0.8%) in combination with CSP (1.2%) were preferred nitrogen sources for high mycelial production and EPS production, respectively. All plant oils tested significantly stimulate cell growth of G. frondosa but they failed to enhance EPS production. The EPS products usually consisted of two fractions of different molecular sizes varied by the plant oils used. The fed-batch fermentation by glucose feeding was performed when the glucose concentration in the medium was lower than 0.5% (5g/L), which greatly enhanced the accumulation of mycelial biomass and EPS; the mycelial biomass and EPS were 3.97g/L and 1.04g/L before glucose feeding, which reached 8.23g/L and 3.88g/L at 13 d of cultivation. In contrast, the mycelial biomass and EPS in the batch fermentation were 6.7g/L and 3.3g/L at 13 d of cultivation. [Copyright &y& Elsevier]

In this article, we report the development of the fast incorporation of primary amine functional groups into a polylactide (PLA) surface using the post-discharge jet region of an atmospheric-pressure nitrogen-based dielectric barrier discharge (DBD). Plasma treatments were carried out in two sequential steps: (1) nitrogen with 0.1% oxygen addition, and (2) nitrogen with 5% ammonia addition. The analyses show that the concentration of N/C ratio, surface energy, contact angle, and surface roughness of the treated PLA surface can reach 19.1%, 70.5 mJ/m(2), 38° and 73.22 nm, respectively. In addition, the proposed two-step plasma treatment procedure can produce a PLA surface exhibiting almost the same C2C12 cell attachment and proliferation performance as that of the conventional gelatin coating method. Most importantly, the processing/preparation time is reduced from 13-15 h (gelatin coating method) to 5-15 min (two-step plasma treatment), which is very useful in practical applications., (Copyright © 2013 Wiley Periodicals, Inc., a Wiley Company.)