Search

Introduction: A spiral clavicle plate has been accepted for its superior multidirectional compatibility in the treatment of midshaft clavicle fractures from a biomechanical perspective. However, the influence of the sextant angle (spiral level) definition on biomechanical performance has not been clarified. A conceptual finite element analysis was conducted to identify the advantages and drawbacks of spiral clavicle plates with various sextant angle definitions. Methods: Conventional superior and three different conceptual spiral plates with sextant angle definitions ranging from 45 to 135 degrees were constructed to restore an OTA 15-B1.3 midshaft clavicle fracture model. Three major loading scenarios (cantilever downward bending, axial compression, and axial torsion) were simulated to evaluate the reconstructed structural stiffness and the stress on the clavicle plate and bone screws. Results: The spiral clavicle plate demonstrated greater capability in resisting cantilever downward bending with an increase in sextant angle and showed comparable structural stiffness and implant stress compared to the superior clavicle plate. However, weakened resistance to axial compression load was noted for the spiral clavicle plate, with lowered stiffness and increased stress on the clavicle plate and screws as the spiral level increased. Conclusion: The spiral clavicle plate has been reported to offer multidirectional compatibility for the treatment of midshaft clavicle fractures, as well as geometric advantages in anatomical matching and reduced skin prominence after surgery. The current study supports that remarkable cantilever bending strength can be achieved with this plate. However, users must consider the potential drawback of lowered axial compression resistance in safety considerations. [ABSTRACT FROM AUTHOR]

Amorphous alloy powder can be obtained by rapid cooling atomization of certain alloy droplets. Fe-based amorphous alloy powder has been favored because of its low production cost and wide application range. Moreover, the application of Fe-based amorphous alloy powder provides a new solution for the application of bulk Fe-based amorphous alloys.The research progress of Fe-based amorphous alloy powder was reviewed, and its research status was summarized in four aspects: coating preparation, magnetic materials, laser 3D printing, and wastewater treatment. The advantages of Fe-based amorphous alloy powder in various fields were analyzed, and the research directions of Fe-based amorphous alloy powder in the fields of preparing high-quality coatings, reuse of aging magnetic powders and additive manufacturing were pointed out. Moreover, the application prospects of Fe-based amorphous alloy powder as sensing, control and other functional devices were prospected.In addition, it also shows great application potential in the fields of small size, low dimentional materials such as thin films and flexible electronics.

Objective evaluations of transverse tarsometatarsal (TMT) hypermobility/instability are lacking. This study aims to radiographically explore the relationship between transverse TMT instability and metatarsus adductus (MA) in hallux valgus (HV). This study retrospectively analyzed 207 feet with varying degrees of HV, employing the distance between the first and second metatarsals (M1-2 distance) to assess transverse TMT instability of the first ray. Participants were categorized into MA and non-MA groups. It was found that the M1-2 distance significantly increased with the hallux valgus angle (HVA) and metatarsus adductus angle (MAA), demonstrating significant differences between the MA and non-MA groups. The measurement of M1-2 distance showed high reliability, and its cutoff value was determined to be 4.05 mm. Additionally, the results suggest that the widening of the M1-2 distance may be a predisposing factor for MA in HV patients, highlighting its role in the pathogenesis of this foot condition. These findings highlight the need for a comprehensive assessment of TMT instability on both the axial and sagittal planes for the surgical planning of HV, particularly when complicated by a large MAA. Based on these insights, reoriented first-TMT arthrodesis might be recommended for HV with significant MA to address potential multiplanar instability. [ABSTRACT FROM AUTHOR]

Backgrounds: A common sequela of hip fracture is loss of ambulation capacity. Prediction of postoperative ambulation capacity is important for surgical and rehabilitation decision making. Handgrip strength is a quick and convenient tool for evaluating postoperative functional ability and outcome in variety of clinical conditions for the elderly and is associated with the use of walking aids. We propose that handgrip strength may be a good predictor for postoperative early ambulation. The purpose of our study was to investigate the contribution of handgrip strength in the prediction of postoperative early ambulation capacity in elderly hip fracture patients.Methods: Clinical data of patients with low-energy hip fractures who received surgery from Jan 2018 to Dec 2019 were prospectively collected. The correlations of ambulation time with complication rate, age, gender, injured side, fracture classifications, surgical procedure, body mass index (BMI), and handgrip strength were analyzed.Results: Sixty-three hip fracture patients were included in this study. Patients whose ambulation time was less than 3 days after the operation had significantly fewer postoperative complications (P = 0.006). Handgrip strength showed the strongest correlation with postoperative early ambulation capacity (P = 0.004). The handgrip strength threshold value for early ambulation was found to be 20.5 kg for male patients and 11.5 kg for female patients.Conclusion: Handgrip strength testis a quick and convenient tool for predicting postoperative early ambulation capacity. In elderly Asians, male patients with a handgrip strength above 20.5 kg and female patients with a handgrip strength above 11.5 kg suggest a high likelihood of early postoperative ambulation and a lower risk of complications after the hip surgery. [ABSTRACT FROM AUTHOR]

Background: Intermittent parathyroid hormone (PTH) can be used to treat osteoporosis of the spine and hip. However, whether it can be used to treat osteoporosis of the mandible is unclear. The purpose of this study was to explore the influence of applying intermittent PTH to ovariectomized rats on the trabecular bone microarchitecture of the mandible and femoral head.Methods: Eighteen female rats were divided into three groups: the healthy group, ovariectomized (OVX) group, and OVX + PTH group. The OVX group and OVX + PTH group had an OVX at 8 weeks of age. The OVX + PTH group received intermittent PTH therapy for 12 weeks. The mandibles and femurs of all rats were removed at 20 weeks and were then scanned using microcomputed tomography (micro-CT).Results: From the micro-CT analysis, the trabecular bone microarchitecture of the mandible and femoral head are offered as follows: (1) The bone volume fraction and trabecular thickness in the OVX group were lower than those in the healthy group. (2) The bone volume fraction and trabecular thickness in the OVX + PTH group approximated those in the healthy group.Conclusion: The conclusions of this study regarding the trabecular bone microarchitecture of the mandible and femoral head are offered as follows: (1) The BV/TV and TbTh in the OVX group were lower than those in the healthy group. (2) The BV/TV and TbTh in the OVX + PTH group approximated those in the healthy group, therefore, intermittent PTH displayed high efficacy for treating femoral or mandibular deterioration of bone microstructure resulting from loss of ovarian function. Osteoporosis of the femur or mandible in the rats was ameliorated by intermittent PTH therapy. [ABSTRACT FROM AUTHOR]