Search

Nitrogen doped carbon nanoparticles on highly porous carbon nanofiber electrodes were successfully synthesized via combining centrifugal spinning, chemical polymerization of pyrrole and a two-step heat treatment. Nanoparticle-on-nanofiber morphology with highly porous carbon nanotube like channels were observed from SEM and TEM images. Nitrogen doped carbon nanoparticles on highly porous carbon nanofiber (N-PCNF) electrodes exhibited excellent cycling and C-rate performance with a high reversible capacity of around 280 mA h g -1 in sodium ion batteries. Moreover, at 1000 mA g -1 , a high reversible capacity of 172 mA h g -1 was observed after 300 cycles. The superior electrochemical properties were attributed to a highly porous structure with enlarged d -spacings, enriched defects and active sites due to nitrogen doping. The electrochemical results prove that N-PCNF electrodes are promising electrode materials for high performance sodium ion batteries., Competing Interests: There are no conflicts to declare., (This journal is © The Royal Society of Chemistry.)

Soft, wearable or printable strain sensors derived from conductive polymer nanocomposites (CPNs) are becoming increasingly ubiquitous in personal-care applications. Common elastomers employed in the fabrication of such piezoresistive CPNs frequently rely on chemically cross-linked polydiene or polysiloxane chemistry, thereby generating relatively inexpensive and reliable sensors that become solid waste upon application termination. Moreover, the shape anisotropy of the incorporated conductive nanoparticles can produce interesting electrical effects due to strain-induced spatial rearrangement. In this study, we investigate the morphological, mechanical, electrical, and electromechanical properties of CPNs generated from thermoplastic elastomer (TPE) triblock copolymer systems containing vapor-grown carbon nanofiber (CNF). Modulus-tunable TPE gels imbibed with a midblock-selective aliphatic oil exhibit well-behaved properties with increasing CNF content, but generally display nonlinear negative piezoresistance at different strain amplitudes and stretch rates due to nanofiber mobility upon CPN strain-cycling. In contrast, a neat TPE possessing low hard-block content yields a distinctive strain-reversible piezoresistive response, as well as low electrical hysteresis, upon cyclic deformation. Unlike their chemically cross-linked analogs, these physically cross-linked and thus environmentally benign CPNs are fully reprocessable by thermal and/or solvent means., Competing Interests: The authors declare no competing financial interest.

α-Fe(2)O(3) nanoparticle-loaded carbon nanofiber composites were fabricated via electrospinning FeCl(3)·6H(2)O salt-polyacrylonitrile precursors in N,N-dimethylformamide solvent and the subsequent carbonization in inert gas. Scanning electron microscopy, transmission electron microscopy, energy dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy, X-ray diffraction, and elemental analysis were used to study the morphology and composition of α-Fe(2)O(3)-carbon nanofiber composites. It was indicated that α-Fe(2)O(3) nanoparticles with an average size of about 20 nm have a homogeneous dispersion along the carbon nanofiber surface. The resultant α-Fe(2)O(3)-carbon nanofiber composites were used directly as the anode material in rechargeable lithium half cells, and their electrochemical performance was evaluated. The results indicated that these α-Fe(2)O(3)-carbon nanofiber composites have high reversible capacity, good capacity retention, and acceptable rate capability when used as anode materials for rechargeable lithium-ion batteries.

LiFePO(4)/CNT/C composite nanofibers were synthesized by using a combination of electrospinning and sol-gel techniques. Polyacrylonitrile (PAN) was used as the electrospinning media and carbon source. Functionalized CNTs were used to increase the conductivity of the composite. LiFePO(4) precursor materials, PAN and functionalized CNTs were dissolved or dispersed in N,N-dimethylformamide separately and they were mixed before electrospinning. LiFePO(4) precursor/CNT/PAN composite nanofibers were then heat-treated to obtain LiFePO(4)/CNT/C composite nanofibers. Fourier transform infrared spectroscopy measurements were done to demonstrate the functionalization of CNTs. The structure of LiFePO(4)/CNT/C composite nanofibers was determined by X-ray diffraction analysis. The surface morphology and microstructure of LiFePO(4)/CNT/C composite nanofibers were characterized using scanning electron microscopy and transmission electron microscopy. Electrochemical performance of LiFePO(4)/CNT/C composite nanofibers was evaluated in coin-type cells. Functionalized CNTs were found to be well-dispersed in the carbonaceous matrix and increased the electrochemical performance of the composite nanofibers. As a result, cells using LiFePO(4)/CNT/C composite nanofibers have good performance, in terms of large capacity, extended cycle life, and good rate capability., (© 2012 American Chemical Society)

Composite carbon-tin oxide (C-SnO(2)) nanofibers are prepared by two methods and evaluated as anodes in lithium-ion battery half cells. Such an approach complements the long cycle life of carbon with the high lithium storage capacity of tin oxide. In addition, the high surface-to-volume ratio of the nanofibers improves the accessibility for lithium intercalation as compared to graphite-based anodes, while eliminating the need for binders or conductive additives. The composite nanofibrous anodes have first discharge capacities of 788 mAh g(-1) at 50 mA g(-1) current density, which are greater than pure carbon nanofiber anodes, as well as the theoretical capacity of graphite (372 mAh g(-1)), the traditional anode material. In the first protocol to fabricate the C-SnO(2) composites, tin sulfate is directly incorporated within polyacrylonitrile (PAN) nanofibers by electrospinning. During a thermal treatment the tin salt is converted to tin oxide and the polymer is carbonized, yielding carbon-SnO(2) nanofibers. In the second approach, we soak the nanofiber mats in tin sulfate solutions prior to the final thermal treatment, thereby loading the outer surfaces with SnO(2) nanoparticles and raising the tin content from 1.9 to 8.6 wt %. Energy-dispersive spectroscopy and X-ray diffraction analyses confirm the formation of conversion of tin sulfate to tin oxide. Furthermore, analysis with Raman spectroscopy reveals that the additional salt soak treatment from the second fabrication approach increases in the disorder of the carbon structure, as compared to the first approach. We also discuss the performance of our C-SnO(2) compared with its theoretical capacity and other nanofiber electrode composites previously reported in the literature.