Search

The application of heat treatments on 1.3 GHz TESLA type cavities in ultra-high vacuum at 250{\deg}C to 350{\deg}C is called medium temperature or mid-T heat treatment. In various laboratories such treatments on superconducting radio frequency (SRF) cavities result reproducible in three main characteristic features for the quality factor $Q_0$ in dependency of the accelerating electric field strength $E_{acc}$. First, comparing mid-T heat treatment with a baseline treatment, a significant increase of $Q_0$ up to $5\cdot10^{10}$ at 2K can be observed. Second, with increasing accelerating gradient $E_{acc}$ the $Q_0$ increases up to a maximum around 16 to 20 MV/m. This effect is known as anti-Q-slope. The third observation for a mid-T heat treatment compared to a baseline treatment is an often reduced maximum gradient $E_{acc}$. The appearance of a high-field-Q-slope (HFQS) was reported after mid-T heat treatments of 3 hours at 350{\deg}C or of 20 hours at 300{\deg}C at DESY. Using the heating temperature and the heating time taken from the temperature profile of the furnace effective oxygen diffusion lengths $l$ were calculated. In the follow-up study presented here, a set of three single-cell cavities with diffusion lengths $l$ above 1700 nm, showing HFQS, were treated with an additional so-called low-T bake of 24-48 hours at 120{\deg}C to 130{\deg}C. The subsequent reproducible Q(E) -performances results indicate that the low-T bake procedure cures the HFQS like for cavities treated with the EuXFEL recipe of EP and following low-T treatments. As presented in the following, Q values of more than $3\cdot10^{10}$ at 16 MV/m and accelerating gradients of 32 to 40 MV/m are achieved., Comment: 6 pages, 7 figures

This comprehensive study, being part of the European XFEL R\&D effort, elucidates the influence of medium temperature (mid-T) heat treatments between 250{\deg}C and 350{\deg}C on the performance of 1.3~GHz superconducting radiofrequency (SRF) niobium cavities. Utilizing a refurbished niobium retort furnace equipped with an inter-vacuum chamber and cryopumps at DESY, we have embarked on an investigation to enhance the state-of-the-art SRF cavity technology. Our research reveals that mid-T heat treatments significantly boost the quality factor ($Q_0$) of the cavities, achieving values between $2\cdot10^{10}$ to $5\cdot10^{10}$ at field strengths around 16~MV/m, while the maximum field strengths are limited to 25-35~MV/m and enhanced sensitivity to trapped magnetic flux is observed. Moreover, we delve into the effects of surface impurity concentration changes, particularly the diffusion of oxygen content, and its impact on performance enhancements. By categorizing treatments based on calculated diffusion lengths using the whole temperature profile, we recognize patterns that suggest an optimal diffusion length conducive to optimizing cavity performance. SIMS results from samples confirm the calculated oxygen diffusion lengths in most instances. Deviations are primarily attributed to grain boundaries in fine-grain materials, necessitating repeated measurements on single-crystal materials to further investigate this phenomenon. Investigations into cooling rates and the resulting spatial temperature gradients across the cavities ranging from 0.04 to 0.2~K/mm reveal no significant correlation with performance following a mid-T heat treatment. However, the increased sensitivity to trapped magnetic flux leads to new challenges in the quest for next-generation accelerator technologies since the requirement for magnetic hygiene gets stricter., Comment: 15 pages, 24 figures

In recent years we increased the typical maximum peak field on axis gradients obtained in L-band superconducting RF (SRF) photoinjector cavities at vertical tests to around 55 MV/m. This was achieved with niobium cathode plugs directly screwed to the cavity back wall omitting an RF choke filter and a load lock system for cathodes. Copper demonstrated being a suitable cathode material in normal conducting injector cavities used at X-Ray Free Electron Lasers (XFELs) operating with pulsed RF. In this article we present the first experimental confirmation that peak field on axis gradients around 55 MV/m and beyond can be achieved in L-band SRF photoinjector cavities with copper cathode plugs screwed to the cavity back wall. We view this as a major milestone for the development of a high gradient photoinjector operating continuous wave (CW)., Comment: 4 pages, 7 figures, to be submitted to PRAB