Search

Abstract The large deformation and strong rheological characteristics of the underground rock body under complex geological conditions have led to the failure of the support system and even the instability of tunnels from time to time. Based on the theory of groundwater seepage, the elastic solution of the mechanical model of the tunnel anchorage support system under seepage is solved, which reveals the influence of seepage on the peripheral rock and the support parameters of the anchorage support system; the viscoelastic solution is solved according to the corresponding principle of elasticity—viscoelasticity, which analyses the influence of seepage on the rheological process of the anchorage support system; and the model is simulated with the help of finite element software, which analyses the agreement and discrepancy of the numerical solution and the theoretical solution. The results show that the analytical and numerical solutions are basically consistent. This study can provide important guidance for controlling long-term stability of water-rich tunnel rocks.

To improve the corrosion resistance and wide the application of Al alloy sheet in the engineering production, a corrosion potential gradient along the thickness of the Al alloy sheet was fabricated using the sprayed Zn layer. The process of arc spraying was employed to obtain the Zn coating with optimizing the parameters. Electrochemical testing was conducted on the surface of Al alloy sprayed with Zn layers at different depths. As the depth in the thickness direction increases, the content of Zn alloy elements gradually decreases and the potential gradually increases. This exhibits a gradual decrease in corrosion tendency. The results of electrochemical impedance spectra (EIS) revealed the existence of pitting corrosion on the surface of the Al alloy. This even extended to the underlying substrate material. In contrast, the Zn coating, when exposed to a corrosive environment, demonstrated the beneficial cathodic effect as a sacrificial anode and the protective function of a passivating film, thus mitigating corrosion. The gradual increase in charge transfer resistance in the impedance spectrum suggested that the corrosion resistance of the sample is increasingly improved. Therefore, it exhibited remarkable resistance to corrosion. Additionally, the SEM surface morphology and XRD pattern were utilized to further explain the corrosion mechanism of the arc-sprayed Zn coating. The Zn coating can provide sacrificial protection to the Al layer due to its higher negative potential and localized corrosion reactivity. This is attributed to the micro-galvanic couples formed between the Zn and Al layer, thus increasing the corrosion resistance of the sheets.

Abstract Glioblastoma organoids (GBOs) serve as a powerful and reliable tool to study glioblastoma stem cells (GSCs) and glioblastoma (GBM). GBOs can be derived from different materials using different methods. To identify the predominant generation methods and the most applications of GBOs, we searched four databases (PubMed, Embase, Web of Science, and Wiley Online Laboratory) from August 2021 to August 2023. After screening, 42 out of 295 articles were included and analyzed. GBOs in these articles were generated using only one material, such as tumor tissues, tumor cells, and gene-edited multifunctional stem cells, or simultaneously using two materials, such as tumor cells and normal organoids. Methodologically, direct cultivation of GBM cells or tissues was the most commonly used method to generate GBOs. Embryonic stem cells (ESCs) and induced pluripotent stem cells (iPSCs) were the frequently used multifunctional stem cells to generate GBOs by simultaneously silencing P53, NF1, and PTEN using CRISPR/Cas9. In terms of applications, GBOs generated by direct cultivation of GBM tissue had the most applications, including molecular mechanisms, therapy, and culture technique. This review provides a theoretical reference for selecting an appropriate method to generate GBOs when studying GSCs and GBM.

Abstract Investigating proton transport at the interface in an excited state facilitates the mechanistic investigation and utilization of nanomaterials. However, there is a lack of suitable tools for in-situ and interfacial analysis. Here we addresses this gap by in-situ observing the proton transport of graphene quantum dots (GQDs) in an excited state through reduction of magnetic resonance relaxation time. Experimental results, utilizing 0.1 mT ultra-low-field nuclear magnetic resonance relaxometry compatible with a light source, reveal the light-induced proton dissociation and acidity of GQDs’ microenvironment in the excited state (Hammett acidity function: –13.40). Theoretical calculations demonstrate significant acidity enhancement in –OH functionalized GQDs with light induction ( $${{\mathrm{p}}}{K}_{{\text{a}}}^{*}$$ p K a * = –4.62, stronger than that of H2SO4). Simulations highlight the contributions of edge and phenolic –OH groups to proton dissociation. The light-induced superacidic microenvironment of GQDs benefits functionalization and improves the catalytic performances of GQDs. Importantly, this work advances the understanding of interfacial properties of light-induced sp 2–sp 3 carbon nanostructure and provides a valuable tool for exploring catalyst interfaces in photocatalysis.

Abstract Background Gastric cancer is the fifth most common cancer type. Most patients are diagnosed at advanced stages with poor prognosis. A non-invasive assay for the detection of early-stage gastric cancer is highly desirable for reducing associated mortality. Methods We collected a prospective study cohort of 110 stage I–II gastric cancer patients and 139 non-cancer individuals. We performed whole-genome sequencing with plasma samples and profiled four types of cell-free DNA (cfDNA) characteristics, fragment size pattern, copy number variation, nucleosome coverage pattern, and single nucleotide substitution. With these differential profiles, we developed an ensemble model to detect gastric cancer signals. Further, we validated the assay in an in-house first validation cohort of 73 gastric cancer patients and 94 non-cancer individuals and an independent second validation cohort of 47 gastric cancer patients and 49 non-cancer individuals. Additionally, we evaluated the assay in a hypothetical 100,000 screening population by Monte Carlo simulation. Results Our cfDNA-based assay could distinguish early-stage gastric cancer from non-cancer at an AUROC of 0.962 (95% CI: 0.942–0.982) in the study cohort, 0.972 (95% CI: 0.953–0.992) in the first validation cohort and 0.937 (95% CI: 0.890–0.983) in the second validation cohort. The model reached a specificity of 92.1% (128/139) and a sensitivity of 88.2% (97/110) in the study cohort. In the first validation cohort, 91.5% (86/94) of non-cancer individuals and 91.8% (67/73) of gastric cancer patients were correctly identified. In the second validation cohort, 89.8% (44/49) of non-cancer individuals and 87.2% (41/47) of gastric cancer patients were accurately classified. Conclusions We introduced a liquid biopsy assay using multiple dimensions of cfDNA characteristics that could accurately identify early-stage gastric cancer from non-cancerous conditions. As a cost-effective non-invasive approach, it may provide population-wide benefits for the early detection of gastric cancer. Trial registration This study was registered on ClinicalTrials.gov under the identifier NCT05269056 on March 7, 2022.

BackgroundChronic viral infections, such as Human Immunodeficiency Virus (HIV), and their reactivation are considered potential contributing factors to Long-Corona Virus Disease (LC). However, research on the long-term sequelae of Long-COVID in individuals with HIV is limited.MethodsWe conducted a case-control study involving a total of 84 participants categorized into two groups: people living with HIV (PLWH) and people not living with HIV (PNLWH) within the six-month post-infection LC population. Differences in sequelae symptoms, cardiovascular biomarkers (VCAM-1, ICAM-1, and ACE2), Severe Acute Respiratory Syndrome Coronavirus 2 neutralization antibodies (SARS-CoV-2 nAb) and cytokines (IFN-γ, IL-6, and IL-17) were analyzed between the two groups.ResultsAfter 6 months of infection, PLWH exhibited significantly higher serum levels of ACE2, VCAM-1, and ICAM-1 (P < 0.01, respectively) compared to PNLWH with COVID-19. Additionally, sequelae symptoms were more pronounced in PNLWH, and there were no differences in serum levels of IFN-γ, TNF-α, IL-6, and IL-17 between the two groups (P > 0.05, respectively).ConclusionPLWH had lower symptoms of LC and reduced frequency of symptoms, increased cardiovascular risk factors, and no differences in levels of inflammation or SARS-CoV-2 nAb levels when compared to PNLWH.

Abstract Background We aimed to investigate the relationship between systemic immune‐inflammation index (SII) and short‐term mortality in acute ischemic stroke (AIS) with internal carotid artery (ICA) severe stenosis and stroke associated pneumonia (SAP) patients. Methods Information on general demographic, laboratory data, CT angiography, magnetic resonance angiography, or digital subtraction angiography were obtained. The predictive power was evaluated by assessing the area under the receiver operating characteristic (ROC) curve. The logistic regression was performed to assess the association of SII and short‐term mortality in severe stenosis ICA‐AIS and SAP patients. Result Among 342 patients with severe stenosis ICA‐AIS and SAP, death occurred in 66 patients during 120 days follow‐up. Multivariate regression analyses indicated that increased SII predicts higher mortality in 120 days follow‐up, and the risk of short‐term mortality in SII > 666.31 × 109/L group is increased 4.671‐fold. Patients with SII > 666.31 × 109/L had higher proportion of male, hypertension, smoking, higher admission NIHSS score, higher systolic blood pressure, and higher proportion of 120 days mortality. Higher SII predicted a worse 120 days mortality was worked out by Kaplan–Meier methods. Conclusion An elevated SII was remarkably associated with 120 days mortality in severe stenosis ICA‐AIS and SAP patients.

2319 aluminum alloy parts was prepared by wire arc additive manufacturing technology. The corrosion properties of additively manufactured 2319 aluminum alloy and 2219 aluminum alloy sheets were systematically investigated by electrochemical tests and localized corrosion tests. The results of electrochemical tests showed that the 2219 aluminum alloy sheet has a lower corrosion current density than the additively manufactured 2319 aluminum alloy. Localized corrosion test results indicated that the additively manufactured 2319 aluminum alloy exhibited a higher intergranular corrosion depth and more severe corrosion morphology than the 2219 aluminum alloy sheet. This suggests that the 2219 aluminum alloy sheet has higher corrosion resistance than the additively manufactured 2319 aluminum alloy. The poor corrosion resistance of additively manufactured 2319 aluminum alloy could be attributed to the formation of a coarse continuous Al2Cu phase along the grain boundary. Based on this, heat treatment was used to dissolve the Al2Cu, which can effectively improve the corrosion resistance of additively manufactured 2319 aluminum alloy to the same level as that of the 2219 aluminum alloy sheet.

Joint homogenization during transition metal carbides ceramic bonding has attracted much attention as a technique to increase the service temperature and relieve the residual stress for various high-temperature applications. In this work, homogeneous joints of ZrC0.85 ceramic were obtained by diffusion bonding using single Nb and multiple Ti/Nb/Ti as the interlayer. The effect of interlayer composition, bonding temperature and holding time on the microstructure of the joints was investigated. The effect of Nb and Ti on the composition homogeneity and the formation of Kirkendall voids in the ZrC0.85 joints was also discussed. When using single Nb as the interlayer, the homogenization of the joints can be achieved at a bonding temperature of ∼1500 °C and holding for 1 h and no Kirkendall voids were observed when further increasing the bonding temperature to 1600 °C because of the good mutual solubility of NbCx and ZrCx and the relative moderate diffusion rate of Nb. However, severe Kirkendall effects were observed at a higher temperature of 1700 °C, which would deteriorate the high-temperature performance of the joints. The adoption of Ti/Nb/Ti further minished the diffusion rate difference of the interfacial elements through the formation of TiCx phase. As a result, only a few Kirkendall voids were formed at 1700 °C. Nano-hardness of the resultant homogeneous joints was comparable to that of the ZrC0.85 ceramic due to their similar composition. This study shows that active diffusion bonding based on interlayer design for homogeneous joints could pave a new way to join transition metal carbides.

Abstract Caspase-8 (Casp8) serves as an initiator of apoptosis or a suppressor of necroptosis in context-dependent manner. Members of the p90 RSK family can phosphorylate caspase-8 at threonine-265 (T265), which can inactivate caspase-8 for bypassing caspase-8-mediated blockade of necroptosis and can also decrease caspase-8 level by promoting its degradation. Mutating T265 in caspase-8 to alanine (A) in mice blocked TNF-induced necroptotic cecum damage but resulted in unexpectedly massive injury in the small intestine. Here, we show RSK1, RSK2, and RSK3 redundantly function in caspase-8 phosphorylation, and the duodenum is the most severely affected part of the small intestine when T265 phosphorylation of caspase-8 was prevented. Eliminating caspase-8 phosphorylation resulted in a duodenum-specific increase in basal caspase-8 protein level, which shall be responsible for the increased sensitivity to TNF-induced damage. Apoptosis of intestinal epithelial cells (IECs) was predominant in the duodenum of TNF-treated Rsk1 − / − Rsk2 − / − Rsk3 − / − and Casp8 T265A/T265A mice, though necroptosis was also observed. The heightened duodenal injury amplified systemic inflammatory responses, as evidenced by the contribution of hematopoietic cells to the sensitization of TNF-induced animal death. Further analysis revealed that hematopoietic and non-hematopoietic cells contributed differentially to cytokine production in response to the increased cell death. Collectively, RSKs emerges as a previously overlooked regulator that, via tissue/organ-constrained inactivating caspase-8 and/or downregulating caspase-8 protein level, controls the sensitivity to TNF-induced organ injury and animal death.

This paper obtained an additively manufactured high-strength Al–Li alloy by laser powder bed fusion (LPBF) based on a third generation AA2195 alloy powder raw material. The relationship between the process optimization, microstructure evolution, and mechanical properties of the as-printed (AP) and heat-treated (HT) specimens was established for the first time to explain the intergranular fracture sensibility during LPBF and reveal the dominant precipitation strengthening mechanism induced by the subsequent heat treatment. The precipitation order of AP Al–Li alloy at the last stage of the solidification process was: L (Liquid phase) →T2 (Al6CuLi3) + θ′(Al2Cu) + δ′/β' (Al3(Li,Zr)) + T (LiAlSi) + Ω (AlCuMgAg). The micro-cracks caused by a relatively high grain boundary coverage of interconnected film-like eutectic phases, as well as micro-voids caused by the localized slip between the coarse T2-phases and soft precipitate-free zones, resulted in the high intergranular fracture sensibility. The well-designed T6 heat treatment of 515 °C/60 min solution treatment and 170 °C/6 h aging treatment was conducted to maximize the precipitation strengthening by T1-phases. The precipitation order of HT Al–Li alloy was supersaturated solid solution → GP zone + δ′/β' → θ′ + T1 (Al2CuLi) + ω (Al7Cu2Fe) + β′. The presence of continuously distributed T1-cells along the grain boundaries was not only capable of providing a pinning effect on dislocations movement and boundary migration, but also able to shorten the pile-up distance on the slip plane. Such phenomena improved the resistance ability of Al–Li alloys to mechanical damage and permitted a significant strength enhancement.

Abstract It is important to strengthen the research on urban rail transit (URT) existing line renovation strategies. In this paper, we investigate the optimization of bottlenecks that are less attractive but have strong travel demand in existing URT networks. A URT local line optimization model is constructed. The maximum passenger flow and minimum project cost are chosen as the optimization objective for the benefit of both passengers and operators, and several actual constraints are considered in the proposed model, such as the station interval. In order to obtain higher computational efficiency and accuracy, a passenger flow allocation method is embedded in a genetic algorithm with elitist preservation. Taking the local network of the Beijing URT as a case study, the calculation results show that the designed algorithm can quickly and effectively obtain the optimal solution, and the generated local line scheme is able not only to meet the regional travel demand, but also to optimize the connection relationship of the existing URT network. This study can provide a reference method for increasing the attraction of URT and optimization of existing URT networks.

Additive manufacturing technology, by manipulating and emulating inherent multiscale, multi-material, and multifunctional structures found in nature, has created new opportunities for constructing heterogeneous structures associated with special properties and achieving ultra-high mechanical performance and reliability in ceramic composite materials. In this study, we have developed an innovative fabrication method designated as coaxial 3D printing for the synchronous construction of two constituents into ceramic composites with a tooth enamel biomimetic microstructure. Herein, the stiff silicate and flexible epoxy served as a strengthening bridge and toughening layer, respectively. The method differed from the traditional approach of randomly dispersing reinforcing components within a ceramic matrix. It allowed for the direct creation of an internally effective three-dimensional reinforcement network structure in ceramic composites. This process facilitated synergistic deformation and simultaneous enhancement of multiple materials and hierarchical structures. Owing to the uniform distribution of internal stress and effective block of microcrack propagation, the biomimetically structured silicate/epoxy ceramic composite has demonstrated much significant enhancement in mechanical properties, including compressive strength (48.8±3.12 MPa), flexural strength (10.39±1.23 MPa), and flexural toughness (218.7±54.6 kJ/m3), which was 0.5, 2.1, and 47.5 times as high as those of the intrinsic brittle silicate ceramics, respectively. In-situ characterization and multiscale finite element simulation of microstructural evolution during three-point bending deformation further validated multiple-step features of the fracture process (silicate bridge fracture, interface detachment, epoxy extraction, and rupture), which benefited from interpenetrating structural features achieved by coaxial printing to accomplish with the complex propagating routines of the crack deflection in silicate ceramic composites. This coaxial 3D printing method paves the way for tailored toughening−strengthening designs for other brittle engineering ceramic materials.

Biochar-assisted anaerobic digestion (AD) remains constrained due to the inefficient decomposition of complex organics, even with the direct interspecies electron transfer (DIET) pathway. The coupling of electrochemistry with the anaerobic biological treatment could shorten lengthy retention time in co-digestion by improving electron transfer rates and inducing functional microbial acclimation. Thus, this work investigated the potential of improving the performance of AD by coupling low-magnitude electric fields with biochar derived from the anaerobically digested biogas residue. Different voltages (0.3, 0.6, and 0.9 V) were applied at various stages to assess the impact on biochar-assisted AD. The results indicate that an external voltage of 0.3 V, coupled with 5 g/L of biochar, elevates CH4 yield by 45.5% compared to biogas residue biochar alone, and the coupled approach increased biogas production by up to 143% within 10 days. This finding may be partly explained by the enhanced utilization of substrates and the increased amounts of specific methanogens such as Methanobacterium and Methanosarcina. The abundance of the former increased from 4.0 to 11.3%, which enhances the DIET between microorganisms. Furthermore, the coupling method shows better potential for enhancing AD compared to preparing iron-based biochar, and these results present potential avenues for its broader applications. HIGHLIGHTS Biochar coupled with electric fields was used to enhance AD.; Coupling of biogas residue biochar and electric fields accelerated the initiation of AD.; The coupled approach improved biogas production by 143% within 10 days.; The abundance of DIET-mediated Methanobacterium was improved to 11.27%.;

Abstract The joints are existing throughout the underground rock mass. It is of great significance to investigate the shear performance of the rock mass to maintain the stability of the underground structure. In this study, we conducted orthogonal tests to determine the proportion of rock-like materials, and used JRC curves to make specimen molds and then prepare the specimens. We conducted straight shear tests and uniaxial compression tests to determine the various mechanical parameters of the rock-like materials. Next, we carried out the compression and shear tests to investigate the shear characteristics of the specimens, and study the damage pattern and shear strength of the jointed rock mass under different confining pressures and roughness levels. The mesoscopic displacements in the shear process of joints were analyzed by using ABAQUS. The test results show that the effect of the confining pressure on the shear strength of the joint plane is relatively obvious, and a larger confining pressure indicates a larger shear strength. The effects of different joint plane roughness and shear rated on the shear characteristics of the joint plane are also significant. The mesoscopic displacement difference inside the joint plane with higher roughness is relatively large, and the stress concentration phenomenon is obvious and lasts longer, which leads to the faster destruction of the specimen with higher roughness and the higher destruction degree. Therefore, we suggest that the priority should be given to the reinforcement of jointed rock mass with high roughness during the construction to prevent sudden destabilization and failure.

As people enter the era of the IoT (Internet of Things), more and more microelectronic devices and flexible electronic devices have been developed and applied. A novel Bi–In–Sn–Zn quaternary solder system is presented, aiming at improving mechanical properties of low-melting solders for flexible electronics. The study examines the differences in the microstructure of the Sn–Bi–In ternary solders before and after the addition of the Zn element, furthermore, it analyzes the role of the Zn element in the Bi–In–Sn system. The results indicate that the Zn element partially exists in the form of a Zn phase, while the remaining portion dissolves in the eutectic structure of the Sn–Bi–In alloy. Moreover, a significantly higher amount of Zn is found to dissolve in the (In,Bi)Sn4 phase compared to the BiIn phase. The dissolved Zn element enhances the strength of the solder by increasing the lattice distortion in the (In,Bi)Sn4 phase and refining the grains of the Sn–Bi–In alloy. Subsequently, the 53Bi30In17Sn–Zn equilibrium phase diagram was obtained by CALPHAD (Calculation of Phase Diagrams) method based on thermodynamic calculation, providing new idea for the future research and development of solder used in the electronic packaging field.

This paper investigates the surface enhancement treatment of 12Cr17Mn6Ni5N steel weld joints using the Strengthened Grinding Process (SGP) and explores its effect on their surface characteristics and tensile performance. The study begins by examining the influence of different SGP durations on the weld joints' surface morphology, microhardness, and residual stress. Subsequently, the tensile properties of the SGP-treated samples are analyzed and the potential mechanisms by which SGP enhances the tensile performance of 12Cr17Mn6Ni5N steel weld joints are discussed. The results reveal that SGP treatment increases the maximum microhardness of 12Cr17Mn6Ni5N steel weld joints to 519.3 HV, marking a 109.9 % improvement as compared to untreated samples. Additionally, the samples’ surface residual stress was changed from residual tensile stress (46.5 MPa) to residual compressive stress (−1253.1 MPa). The SGP-treated samples exhibit a tensile strength of 671.43 MPa, marking an 8.51 % increase as compared to the untreated samples, while also achieving a simultaneous elongation of 16.42 %. The research demonstrates that SGP is an effective method for enhancing the tensile performance of specific mechanical components.

Carbon-based quantum dots (CQDs) have been shown to have promising application value in tumor diagnosis. Their use, however, is severely hindered by the complicated nature of the nanostructures in the CQDs. Furthermore, it seems impossible to formulate the mechanisms involved using the inadequate theoretical frameworks that are currently available for CQDs. In this review, we re-consider the structure-property relationships of CQDs and summarize the current state of development of CQDs-based tumor diagnosis based on biological theories that are fully developed. The advantages and deficiencies of recent research on CQDs-based tumor diagnosis are thus explained in terms of the manifestation of nine essential changes in cell physiology. This review makes significant progress in addressing related problems encountered with other nanomaterials.

Abstract To quickly determine the blasting block degree and conduct an accurate and objective analysis of the tunnel blasting effect, this study has enhanced and improved upon the traditional genetic algorithm and Otsu algorithm. It has combined it with the marking watershed method and utilized ground digital acquisition to capture images of blasting debris. These images are then used in our custom-developed blasting analysis software to calculate the blasting block degree distribution and provide a quantitative analysis of blasting block degree. The research results show that the optimized image segmentation algorithm effectively improves the traditional threshold segmentation method on the poor effect of segmentation of the edge of the adherent block or the direct application of the watershed segmentation of the over-segmentation problem, to improve the segmentation accuracy based on the new segmentation technology is close to the traditional technology in terms of time. Through the self-developed software, the construction personnel in the project site to quickly obtain the blasting block degree histogram, block degree cumulative curve and other important indicators of the evaluation of the effect of blasting block degree, to provide data support for on-site construction, to assist in the modification of the blasting program, and to improve the efficiency of construction. This study realizes the rapid detection and block identification of blasting blocks, provides data support for the optimization of blasting parameters, and has good application and promotion value.

Abstract The purpose of the present study is to predict and draw up non-grain cultivated land (NCL) susceptibility map based on optimized Extreme Gradient Boosting (XGBoost) model using the Particle Swarm Optimization (PSO) metaheuristic algorithm. In order to, a total of 184 NCL areas were identified based on historical records, and a total of 16 NCL susceptibility conditioning factors (NCLSCFs) were considered, based on both a systematic literature survey and local environmental conditions. The results showed that the XGBoost model optimized by PSO performed well in comparison to other machine learning algorithms; the values of sensitivity, specificity, PPV, NPV, and AUC are 0.93, 0.89, 0.88, 0.93, and 0.96, respectively. Slope, rainfall, fault density, distance from fault and drainage density are most important variables. According to the results of this study, the use of meta-innovative algorithms such as PSO can greatly enhance the ability of machine learning models.

This paper proposes a novel relay algorithm to optimize the communication throughput of unmanned aerial vehicle (UAV) mobile relay formations while considering the challenges posed by obstacle avoidance, channel complexity, high dynamics of UAVs, and real-time mission requirements. To tackle the non-convex nature of this problem, we develop the unscented Kalman filter and hybrid particle swarm optimization (UKF-HPSO) algorithm. Initially, real-time prediction of the source and destination of UAV positions is accomplished using the UKF. Subsequently, these predicted coordinates serve as inputs for achieving the optimal deployment of relay UAVs under the constraints imposed by HPSO. The superiority of the UKF-HPSO algorithm compared to baseline approaches is demonstrated through extensive simulations. System throughput is effectively optimized while maintaining real-time performance by our proposed algorithm, which addresses the unique challenges of UAV communication in dynamic environments.

The effects of particles on precipitation reactions in aluminum alloy have been widely unknown. Al–Fe–Mn–Si–Mg–Cu alloy strengthened with uniformly distributed Al(Fe,Mn)Si nanoparticles was successfully produced in this study. The alloy was then characterised using high-resolution scanning transmission electron microscopy (HRTEM), to provide a fundamental insight into the interface precipitation. Interfacial precipitations of several tens of nanometers in size was formed after aging, which were found to be Al5Cu6Mg2 and Si phases. The results demonstrated that the facetted α-Al(Fe,Mn)Si particles had a significant influence on precipitation adjacent to the α-Al(Fe,Mn)Si/Al interfaces. Semi-coherent α-Al(Fe,Mn)Si/Al interfaces were revealed to have periodically spaced misfit dislocations that are generally considered to be beneficial to heterogeneous precipitation. They not only reduce nucleation energy barriers but also act as short-circuit diffusion paths to accelerate growth rates by transporting solute atoms and vacancies.

Joining of dissimilar superalloys is indispensable in the field of advanced manufacture, achieving a high-quality joint while minimizing thermal damage to substrates during diffusion bonding is a critical but challenging pursuit. A low-temperature and rapid diffusion bonding strategy enabled by pulsed current was proposed to resolve this challenge. Attributed to the enhanced interfacial plastic-deformation and carbide-precipitation, pulsed current rapidly achieved a nanovoid-free and tight joint of GH3536 and GH5188 superalloys at a low temperature of 850 °C for 5 min. Meanwhile, the rapid joining process prevented the interfacial carbides from coarsening and allowed their elimination in a short-term heat-treatment. The carbide dissolution, recrystallization of highly-deformed grain and cross-interface grain growth during heat-treatment significantly enhanced the joint performance, the heat-treated joint exhibited a high ultimate strain of 25.5 % and a tensile strength comparable to the raw GH3536.

The utilization of microwave hybrid heating in the field of low-temperature joining presents a notable benefit of delivering both selective and uniform heating, a feature that is not commonly observed in traditional welding methods. This work utilized numerical simulation to predict the heating effects of three susceptors. Furthermore, the impacts of susceptor variants on the interface morphology, mechanical properties, and fracture morphology of the Sn-3.0 Ag-0.5 Cu joint were studied. In the current study, the normal MHH technique was utilized with parameters of 900 W and 240 s to achieve successful joint production. According to the numerical simulation, the heating rate of carbon powder as a susceptor was found to be greater than that of graphite, while silicon carbide susceptor exhibited the slowest heating rate. Nevertheless, the combustion of carbon powder during the MHH process poses a potential risk to the integrity of the microwave cavity. As a result, graphite powder was selected as a more suitable susceptor. The experimental findings indicate that the shear strength of the joint with silicon carbide and charcoal as the susceptor is 75.4 % and 91.0 % of that with graphite as the susceptor, respectively. The fracture modes of the three samples with various susceptors are mixed fracture.

The effect of pre-stretching on solid-liquid interaction, microstructure and brazing performance of AA4343/AA3xxx/AA4343 layered aluminum sheet during brazing at the atomic level (solid solution), nanoscale (dislocation) and micron level (grain boundary) are studied by glow discharge optical emission spectrometry (GDOES), scanning electron microscope (SEM), electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM). The microstructure after brazing largely depends on the forming condition. The driving force of liquid film migration (LFM) is the reduction of stored deformation energy. The interaction between the liquid clad and solid core layers changes the elemental distribution and microstructure, which in turn affects the brazing performance of the sheet. The results reveal the mechanism of solid-liquid interaction of layered aluminum sheet during brazing and clarify the driving force of LFM of layered aluminum sheet during brazing. Consequently, these results provide important insights for the design and theoretical research of functional layered aluminum sheet.

LEO satellite constellation (LSC) offers seamless and fast connectivity for non-terrestrial network (NTN).However, the lack of QoS guarantees for users significantly impacts the performance of the NTN system.Considering multi-QoS metrics, a capacity and downlink budget model for LSC was established, and subsequently, the establishment of inter-satellite links was framed as a link budget issue for the QoS guarantee.The non-dominated sorting genetic algorithm (INSGA-II) with improved crossover and mutation operators was proposed to optimize LSC, aiming to maximize coverage and system capacity while minimizing constellation costs.The numerical results demonstrate that the designed LSC exhibits comparable or superior performance to Telesat and Kepler, and its scale is only 64% of the Kepler system.

Abstract Conventional knowledge graph representation learn the representation of entities and relations by projecting triples in the knowledge graph to a continuous vector space. The vector representation increases the precision of link prediction and the efficiency of downstream tasks. However, these methods cannot process previously unseen entities during the knowledge graph evolution. In other words, the model trained on the source knowledge graph cannot be applied to the target knowledge graph containing new unseen entities. Recently, a few subgraph-based link prediction models obtained the inductive ability, but they all neglect semantic information. In this work, we propose an inductive representation learning model TGraiL which considers not only the topological structure but also semantic information. First, distance in the subgraph is used to encode the node’s topological structure. Second, the projection matrix is used to encode the entity type information. Finally, both kinds of information are fused for training to acquire the ultimate vector representation of entities. The experimental results indicate that the model’s performance has been significantly improved compared to the existing baseline models, demonstrating the method’s effectiveness and superiority.

Abstract Global science education reform calls for developing student knowledge-in-use that applies the integrated knowledge of core ideas and scientific practices to make sense of phenomena or solve problems. Knowledge-in-use development requires a long-term, standards-aligned, coherent learning system, including curriculum and instruction, assessment, and professional learning. This paper addresses the challenge of transforming standards into classrooms for knowledge-in-use and presents an iterative design process for developing a coherent and standards-aligned learning system. Using a project-based learning approach, we present a theory-driven, empirically validated learning system aligned with the U.S. science standards, consisting of four consecutive curriculum and instruction materials, assessments, and professional learning to support students’ knowledge-in-use in high school chemistry. We also present the iterative development and testing process with empirical evidence to support the effectiveness of our learning system in a five-year NSF-funded research project. This paper discusses the theoretical perspectives of developing an NGSS-aligned, coherent, and effective learning system and recaps the development and testing process by unpacking all essential components in our learning system. We conclude that our theory-driven and empirically validated learning system would inform high school teachers and researchers across countries in transforming their local science standards into curriculum materials to support students’ knowledge-in-use development.

AbstractContext Dihydromyricetin (DMY) is extracted from vine tea, a traditional Chinese herbal medicine with anti-cancer, liver protection, and cholesterol-lowering effects.Objective This study investigated the mechanism of DMY against hepatocellular carcinoma (HCC).Materials and methods Potential DMY, HCC, and cholesterol targets were collected from relevant databases. PPI networks were created by STRING. Then, the hub genes of co-targets, screened using CytoHubba. GO and KEGG pathway enrichment, were performed by Metascape. Based on the above results, a series of in vitro experiments were conducted by using 40–160 μM DMY for 24 h, including transwell migration/invasion assay, western blotting, and Bodipy stain assay.Results Network pharmacology identified 98 common targets and 10 hub genes of DMY, HCC, and cholesterol, and revealed that the anti-HCC effect of DMY may be related to the positive regulation of lipid rafts. Further experiments confirmed that DMY inhibits the proliferation, migration, and invasion of HCC cells and reduces their cholesterol levels in vitro. The IC50 is 894.4, 814.4, 467.8, 1,878.8, 151.8, and 156.9 μM for 97H, Hep3B, Sk-Hep1, SMMC-7721, HepG2, and Huh7 cells, respectively. In addition, DMY downregulates the expression of lipid raft markers (CAV1, FLOT1), as well as EGFR, PI3K, Akt, STAT3, and Erk.Discussion and conclusion The present study reveals that DMY suppresses EGFR and its downstream pathways by reducing cholesterol to disrupt lipid rafts, thereby inhibiting HCC, which provides a promising candidate drug with low toxicity for the treatment of HCC.

Remote sensing spatiotemporal fusion technology can provide abundant data source information for assimilating crop growth model data, enhancing crop growth monitoring, and providing theoretical support for crop irrigation management. This study focused on the winter wheat planting area in the southeastern part of the Loess Plateau, a typical semi-arid region, specifically the Linfen Basin. The SEBAL and ESTARFM were used to obtain 8 d, 30 m evapotranspiration (ET) for the growth period of winter wheat. Then, based on the ‘localization’ of the CERES-Wheat model, the fused results were incorporated into the data assimilation process to further determine the optimal assimilation method. The results indicate that (1) ESTARFM ET can accurately capture the spatial details of SEBAL ET (R > 0.9, p < 0.01). (2) ESTARFM ET can accurately capture the spatial details of SEBAL ET (R > 0.9, p < 0.01). The calibrated CERES-Wheat ET characteristic curve effectively reflects the ET variation throughout the winter wheat growth period while being consistent with the trend and magnitude of ESTARFM ET variation. (3) The correlation between Ensemble Kalman filter (EnKF) ET and ESTARFM ET (R2 = 0.7119, p < 0.01) was significantly higher than that of Four-Dimensional Variational data assimilation (4DVar) ET (R2 = 0.5142, p < 0.01) and particle filter (PF) ET (R2 = 0.5596, p < 0.01). The results of the study provide theoretical guidance to improve the yield and water use efficiency of winter wheat in the region, which will help promote sustainable agricultural development.

Linings and anchor bolts, as common support structures, play a crucial role in ensuring the stability of tunnel surrounding rock. This study aims to investigate the elastic–plastic behavior of lining-anchor bolt support structures in deep circular tunnels under static water pressure. Based on the Mohr–Coulomb (M-C) criterion and equivalent substitution method, this study derives the solution process for the radius of the plastic zone and the elastic–plastic stress expressions under a given lining internal pressure. Furthermore, through examples, this study analyzes the radius of the plastic zone and the stress evolution curve of the lining-anchor bolt-supported surrounding rock system under three conditions: without anchoring, various elastic moduli, and different anchor bolt support angles. Finally, this study verifies the rationality of the elastic–plastic analytical solution for the lining-anchor bolt-supported surrounding rock structure through numerical simulation methods. The integrated lining-anchor bolt support is notably effective in inhibiting the expansion of the plastic zone, particularly in soft rock. Additionally, the elastic modulus and circumferential spacing of the anchor bolts significantly influence the plastic zone inhibition rate in soft rock.

Hepatocellular carcinoma (HCC) is the third leading cause of cancer-related deaths worldwide, and its prevention and treatment face severe challenges. It is crucial to improve the targeting of drugs on tumor cells and tissues. Celastrol (CeT), as an active ingredient of traditional Chinese medicine, possesses strong antitumor effects, especially in triggering apoptosis of HCC. However, due to its toxicity and lack of targeting, its application is greatly limited. HMCLPs, a nano-biomimetic platform carrying CeT with controllable drug release, enhanced targeting, and immunocompatibility, were developed for the first time, which can be used for the treatment of HCC. By utilizing homologous cell membranes and hyaluronic acid (HA), HMCLPs can precisely target tumor regions and release CeT in a controlled manner. Both in vitro and in vivo studies have demonstrated that HMCLPs loaded with CeT significantly increased the accumulation of reactive oxygen species (ROS), induced mitochondrial damage, and triggered apoptosis of HCC cells, resulting in effective treatment with minimal adverse reaction. The development of HMCLPs as a nanocarrier system for CeT delivery offers a promising therapeutic strategy for HCC. This innovative approach improves the targeted delivery and bioavailability of CeT, dramatically induces apoptosis in HCC cells, and exerts its powerful antitumor effects while minimizing systemic toxicity. The present study highlights the potential of combining innovative nanocarriers with powerful natural compounds such as CeT to enhance efficacy and reduce toxicity.

This study aimed to provide foundational research for the biological control of postharvest avocado fruits anthracnose and establish a microbial system of postharvest avocado fruits. The high-throughput sequencing of avocado fruits from the anthracnose-infected and healthy groups was performed using Illumina NovaSeq second-generation sequencing technology. The results revealed that, except for Colletotrichum sp. strain 38#, there were differences in the bacterial community structure of avocados before and after infection, as determined through alpha and beta diversity analysis. Additionally, there were significant differences in the endophytic fungal community structure, allowing clear differentiation between the infected and healthy avocados. The endophytic bacterial community was primarily composed of 4 phyla and 10 genera, with the Bacteroidota phylum and Chryseobacterium genus demonstrating sensitivity to anthracnose pathogens, as evidenced by a decrease in their relative abundance after infection. The endophytic fungal community was characterized by 3 phyla and 10 genera. After infection, the relative abundance of 2 phyla (Anthophyta and Basidiomycota) and 7 genera (Eucalyptus, Candida, Kluyveromyces, Talaromyces, Oidiodendron, Nigrospora, and Pestalotiopsis) decreased, whereas the relative abundance of the Colletotrichum genus increased dramatically. The LEfSe (Linear discriminant analysis Effect Size) analysis indicated that significant biomarkers were more prevalent in endophytic bacteria than in endophytic fungi in the avocados. In endophytic bacteria, the key biomarkers included the Firmicutes phylum (Bacilli class), Proteobacteria phylum (Gammaproteobacteria class, Pseudomonadales order, Pseudomonadaceae family, and Pseudomonas genus), Flavobacteriales order, Weeksellaceae family, and Chryseobacterium genus. In endophytic fungi, the important biomarkers were Saccharomycetes class (Saccharomycetales order), Glomerellales order (Glomerellaceae family and Colletotrichum genus), and Botryosphaeriales order (Botryosphaeriaceae family and Lasiodiplodia genus). These results may provide a theoretical basis for the development of future biological agents for avocado anthracnose.

This study presents a novel approach in the realm of catalytic organic synthesis by integrating biomass catalytic conversion with organic synthesis techniques. Utilizing N-acetylglucosamine as the primary feedstock, the first phase of the research involves its catalytic transformation into 5-hydroxymethylfurfural (HMF). The subsequent phase employs a condensation reaction between HMF and 3,3-Dimethyl-2-butanone to synthesize a new compound, (E)-1-(5-(hydroxymethyl) furan-2-yl)-4,4-dimethylpent-1-en-3-one. This two-step process not only demonstrates the feasibility of converting biomass into valuable chemical precursors but also exemplifies the synthesis of novel compounds through green chemistry principles. The successful execution of this methodology offers fresh insights and opens new avenues for advancements in catalytic organic synthesis, emphasizing sustainability and efficiency.

Objective: To investigate the involvement of the homeobox gene B5 (HOXB5) in the progression and metastasis of osteosarcoma. Methods: The expression of HOXB5 in human osteosarcoma tissues and its correlation with clinical indicators were investigated using bioinformatics analysis and immunohistochemical labelling. Human osteosarcoma cells (HOS, MG63, U2OS, and Saos-2) and normal human osteoblasts (hFOB1.19) were cultivated. The expression of HOXB5 in these cells was detected using western blotting (WB) and RT‒PCR. Two cell lines exhibiting elevated HOXB5 expression were chosen and divided into three groups: the blank group (mock), control group (control) and transfection group (shHOXB5). The transfection group was infected with lentivirus expressing shRNAs targeting HOXB5. The transfection efficiency was detected by WB. Cell proliferation suppression was measured by CCK-8 and 5-ethynyl-2′-deoxyuridine (EdU) assays; the percentage of apoptotic cells was determined by flow cytometry; and cell migration and invasion were detected via the Transwell chamber test. WB was utilized to determine the protein expression of genes linked to metastasis (MMP2, MMP9), apoptosis (Bax, Bcl-2), and the JAK2/STAT3 pathway (JAK2, p-JAK2, STAT3, p-STAT3). Results: In osteosarcoma tissues, HOXB5 expression was elevated and strongly correlated with distant metastasis. Silencing HOXB5 reduced the proliferation, migration and invasion of osteosarcoma cells; prevented the progression and metastasis of tumours in tumour-bearing nude mice; and reduced the activation of key proteins in the JAK2/STAT3 signalling pathway. Conclusion: Through the JAK2/STAT3 signalling pathway, HOXB5 plays a crucial role in the malignant progression of osteosarcoma and is a promising target for osteosarcoma treatment.

Soil nitrogen (N) availability is one of the limiting factors of crop productivity, and it is strongly influenced by global change and agricultural management practices. However, very few studies have assessed how the winter drought affected soil N availability during the subsequent growing season under chemical fertilization. We conducted a field investigation involving snow removal to simulate winter drought conditions in a Mollisol cropland in Northeast China as part of a 6-year fertilization experiment, and we examined soil physicochemical properties, microbial characteristics, and N availability. Our results demonstrated that chemical fertilization significantly increased soil ammonium and total N availability by 42.9 and 90.3%, respectively; a combined winter drought and fertilization treatment exhibited the highest soil N availability at the end of the growing season. As the growing season continued, the variation in soil N availability was explained more by fertilization than by winter drought. The Mantel test further indicated that soil Olsen-P content and microbial carbon use efficiency (CUE) were significantly related to soil ammonium availability. A microbial community structure explained the largest fraction of the variation in soil nitrate availability. Microbial CUE showed the strongest correlation with soil N availability, followed by soil available C:P and bacteria:fungi ratios under winter drought and chemical fertilization conditions. Overall, we clarified that, despite the weak effect of the winter drought on soil N availability, it cannot be ignored. Our study also identified the important role of soil microorganisms in soil N transformations, even in seasonally snow-covered northern croplands.

Abstract Multistep photoswitches are able to engage in different photoisomerization pathways and are challenging to control. Here we demonstrate a multistep sequence of E/Z isomerization and photocyclization/cycloreversion of photoswitches via manipulating the strength and mechanism of noncovalent chalcogen bonding interactions. The incorporation of chalcogens and the formyl group on open ethene bridged dithienylethenes offers a versatile skeleton for single photochromic molecules. While bidirectional E/Z photoswitching is dominated by neutral tellurium arising from enhanced resonance-assisted chalcogen bonding, the creation of cationic telluronium enables the realization of photocyclization/cycloreversion. The reversible nucleophilic substitution reactions further allow interconversion between neutral tellurium and cationic telluronium and selection of photoisomerization mechanisms on purpose. By leveraging unique photoswitching patterns and dynamic covalent reactivity, light and pH stimuli-responsive multistate rewritable materials were constructed, triggered by an activating reagent for additional control. The results should provide ample opportunities to molecular recognition, intelligent switches, information encryption, and smart materials.

The preparation of new solder joint materials for chip packaging by designing a variety of brazing material mixes has become one of the future research directions for solder joints. They added low melting point elements to traditional solder materials to prepare low-temperature hybrid solder to meet the low-temperature packaging trend. To improve the performance of low-temperature solder, adding some alloying elements can refine the grain, change the IMC morphology and size, and improve the joint strength to a certain extent. The design of the hybrid solder joint system needs to be based on different metal pads. There are various failure modes of interconnected solder joints on different metal pads. Therefore, the interfacial response, microstructure, and mechanical properties between different hybrid solder and different metal pads need to be studied to optimize the design of the hybrid solder joint system. This paper investigated hybrid low-temperature Sn–3Ag-0.5Cu/Sn–58Bi solder joints on Au/Ni/Cu (ENIG) and Au/Pd/Ni/Cu (ENEPIG) substrates. The addition of Pd elements can change the IMC morphology of hybrid solder joints and affect the fracture failure mode of the joints under shear, with a higher average shear strength at different process parameters than ENIG welded joints. Finally, the presence form of Pd elements in the solder joints was observed under TEM and the fracture mechanism was analyzed. The results showed that Pd atoms on ENEPIG pads can replace some Cu atoms to form (Cu, Pd)6Sn5 intermetallic compounds, distorting the lattice stripe to produce distortions. And compared to ENIG pads, the IMC morphology is pin-rod-like and finer, with more complex grain boundary paths between the grains of the hybrid solder.

In recent years, in order to adapt to the trend of low-temperature assembly and integration, low-temperature hybrid solders with multiple elements added to the tin solder matrix have been investigated. In this regard, the morphology and size of intermetallic compounds (IMCs) are altered by adding some alloying elements, and the strength of solder joints is improved to some extent. Different pad surface treatments affect the growth of IMC, which leads to various failure modes in interconnect solder joints. Therefore, it is necessary to study the interfacial reaction, microstructure and mechanical properties of hybrid solder and different metal pads to explore the growth mechanism of IMC and the failure modes of solder joints. In this paper, mixed Sn–3Ag-0.5Cu/Sn–58Bi low-temperature solder joints on Au/Ni/Cu (ENIG) and Au/Pd/Ni/Cu (ENEPIG) substrates are investigated. The results show that the addition of palladium element can change the IMC morphology, refine the grain size of the hybrid solder joints, and affect the fracture failure mode of the solder joints under shear force. The average shear strength is significantly higher than that of solder joints with ENIG surfaces under different process parameters. Thermodynamic calculations of enthalpy change and the effect of Jackson's parameter α value on IMC morphology are also investigated in this paper. The addition of palladium elements increases the α value and is more favorable to the formation of columnar grains. This provides guidance for the grain growth of IMC in hybrid solder joints with added alloying elements.

Abstract The optimal application of nutrients, such as nitrogen and phosphorus, to the soil is crucial for achieving high crop yields with minimal environmental impact. However, the effect of spatio-temporal changes in soil nutrient supply on crop yield is poorly understood in China. Here, we present a framework that combines environmental data, fertilizer field experiments, and machine learning to estimate the rice yield responses to different nutrient conditions and overall farmland nutrient sustainability in southwest China from 2009 to 2019. The results show that the fertilizer input has contributed to the long-term increase in rice yield over the past ten years. The fertilizer use has increased rice yield by 2.3–2.4 tons per hectare per year. However, the nutrient use efficiency decreased, with the fertilizer contribution ratio declining from 29.3% in 2009 to 27.5% in 2019. Further, 19% of the rice-growing farmlands are at risk of nutrient excess, and 36% are at risk of nutrient degradation. Controlling nitrogen and phosphorus input is key to nutrient regulation, and our approach may guide the sustainable use of nutrient resources on farmlands.

This paper describes the droplet transfer behavior and weld formation of laser-arc hybrid welding with cable-type welding wire (CWW). The droplet transfer behavior was photographed in real time by using a high-speed camera. The effects of energy parameters on arc morphology, droplet transfer behavior and weld formation were studied through experimental and theoretical analyses. The results show that the arc is deflected toward the laser direction, and the deflection degree increases with increasing laser power. The interaction between the laser and arc is enhanced by rotating the arc. The rotating arc enhances the interaction between plasma, the arc is more compressed and the arc volume is smaller as the welding current increases. The droplet transfer frequency increased with increasing laser power and decreased after reaching the critical value. The reaction force of metal vapor and electromagnetic force affect the droplet transfer frequency, and the maximum frequency of droplet transfer is 180.8 Hz under a laser power of 2.5 kW. The rotational force promotes molten droplet transfer and maintains the axial transition, and the welding current has a strong effect on increasing the droplet transfer frequency. The influence of laser power on weld penetration is greater than that of welding current, the weld penetration increases significantly with increasing laser power, and the cross section of the weld seam exhibits laser-arc hybrid welding characteristics.

2319 aluminum alloy was prepared using wire arc additive manufacturing (WAAM) technique. The solid solution time of achieving improving corrosion resistance in WAAM 2319 aluminum alloy was investigated. The results indicated that the as deposited 2319 aluminum alloy was composed of dendritic grains. Numerous inter-granular intermetallic were continuously distributed along the grain boundary. As the solid solution time increased, the inter-granular intermetallic gradually dissolved into α-Al matrix resulting in discontinuously distribution and more homogeneous element distribution. Electrochemical experiment results indicated that the corrosion potential of WAAM 2319 aluminum alloy gradually increased with the increase of solid solution time. This indicated that increasing solid solution time could effectively increased the corrosion resistance of WAAM 2319 aluminum alloy. Improved corrosion resistance can be attributed to refined and discontinuous inter-granular intermetallic.

With the rapid development of 3D packaging, it is of great practical significance to understand the failure mechanism of solder joints in heterogeneous integration devices. In this study, the grain orientation and microstructure evolution of SAC305 solder joints were investigated in thermal shock tests for fan-out wafer level packaging. The heterogenous evolution of microstructure in Sn–3Ag-0.5Cu (SAC305) solder joints was investigated using electron backscattered diffraction (EBSD) and nanoindentation analysis. When the thermal shock reaches 1000 cycles, the local deformation caused the heterolattices in the joint to rotate toward the corners due to the thermal expansion. During deformation, sub-grain formation is accompanied by an increase in dislocations, the accumulation of plastic slip, and the activation of slip systems. The energy stored by this deformation is released in the form of cracks. The work in this paper provides new insights into the early stages of grain orientation, microstructural deformations and the accumulation of stored energy associated with these deformations, providing a scientific basis for the application and failure analysis of large size fan-out welded joints in complex working conditions.

To investigate the contents of carbon, nitrogen, and phosphorus in tea plantation soils and their ecological stoichiometric characteristics, as well as their response to environmental factors in high-latitude regions of China, soil samples from 0 to 20 cm depth were collected from tea plantations at different altitudes and cultivation years in the main tea-producing areas of Shaanxi Province. These samples were used to determine the soil organic carbon (SOC), total nitrogen (TN), and total phosphorus (TP) contents and to calculate their stoichiometric ratios. The findings revealed the following: the average soil SOC and TN content in tea gardens were 13.15 and 1.30 g·kg−1, respectively, exceeding the national soil average. These values met the Class I tea garden fertility standards. However, the average soil TP content, at 0.45 g·kg−1, fell below the national soil average, meeting the Class II tea garden fertility standards. In tea gardens, the average ratios of carbon to nitrogen (C:N), carbon to phosphorus (C:P), and nitrogen to phosphorus (N:P) in the soil were 10.42, 30.98, and 3.32, respectively. These ratios were all lower than the national soil average, indicating relatively high phosphorus availability but nitrogen deficiency in tea garden soils. As altitude increased, there was a decline in soil SOC content, C N, and C P ratios, followed by a subsequent increase. No significant changes were seen in TN, TP, and N P ratio in the soil, but there was an increase in SOC content, TN content, and C P ratio during cultivation. The N-to-P ratio initially increased before decreasing, while the C-to-N ratio decreased before increasing. Soil TP content did not change significantly. The study recommends careful nitrogen fertilizer application in tea garden management to balance nitrogen and phosphorus.

With the swift advancement of wearable electronics and artificial intelligence, the integration of electronic devices with the human body has advanced significantly, leading to enhanced real-time health monitoring and remote disease diagnosis. Despite progress in developing stretchable materials with skin-like mechanical properties, there remains a need for materials that also exhibit high optical transparency. Supercapacitors, as promising energy storage devices, offer advantages such as portability, long cycle life, and rapid charge/discharge rates, but achieving high capacity, stretchability, and transparency simultaneously remains challenging. This study combines the stretchable, transparent polymer PEDOT:PSS with MnO2 nanoparticles to develop high-performance, stretchable, and transparent supercapacitors. PEDOT:PSS films were deposited on a PDMS substrate using a spin-coating method, followed by electrochemical deposition of MnO2 nanoparticles. This method ensured that the nanosized MnO2 particles were uniformly distributed, maintaining the transparency and stretchability of PEDOT:PSS. The resulting PEDOT:PSS/MnO2 nanoparticle electrodes were gathered into a symmetric device using a LiCl/PVA gel electrolyte, achieving an areal capacitance of 1.14 mF cm−2 at 71.2% transparency and maintaining 89.92% capacitance after 5000 cycles of 20% strain. This work presents a scalable and economical technique to manufacturing supercapacitors that combine high capacity, transparency, and mechanical stretchability, suggesting potential applications in wearable electronics.