Search

In the present work the effect of surface roughness on oxidation behavior during the early stages of high temperature exposure of Ni-base superalloy IN 625 is described. The surface roughness was described using standard contact profilometer as well as novel method, fractal analysis. It was found that the different surface preparation resulted in a difference in roughness with a parameter increase of at least one order of magnitude for the ground sample as compared with the polished sample. The oxidation test was performed in a horizontal tube furnace. Post exposure analyses including glow discharge optical emission spectrometry (GD OES) and scanning electron microscopy (SEM), which revealed that grinding lowers the oxidation kinetics of IN 625. It was found that surface preparation influences the oxide scale composition and morphology. The hypothesis explaining the mechanism responsible for the changes in oxidation behavior is proposed as well., Comment: Accepted manuscript

In the present work, it is shown that the surface preparation method used on two Ni-based superalloys prior to aluminizing chemical vapor deposition (CVD) is one of the most important factors determining the oxidation resistance of aluminized Ni-based superalloys. It was found that grit blasting the substrate surface negatively affects the oxidation resistance of the aluminized coatings. For grit blasted and aluminized IN 625, a thicker outer NiAl coating was formed compared to that of IN 738. In contrast, no effect on NiAl coating thickness was found for grit blasted and aluminized IN 738. However, a thicker interdiffusion zone (IDZ) was observed. It was shown that the systems with grit-blasted surfaces reveal worse oxidation resistance during thermal shock tests, namely, a higher mass loss was observed for both grit blasted and aluminized alloys, as compared to ground and aluminized alloys. A possible reason for this effect of remaining alumina particles originating from surface grit blasting on the diffusion processes and stress distribution at the coating/substrate is proposed., Comment: Accepted manuscript Metals 2019

Fe based alloys are commonly used in almost every sector of human life. For different reasons, the surfaces of the real parts are prepared using different methods, e.g., mirror-like polishing, grit-blasting, etc. The purpose of the present work is to answer the question how the surface preparation influences the oxidation behavior of Fe-based alloys. To answer this question, a high purity model alloy, Fe 5 wt Al, was isothermally oxidized in a thermogravimetrical furnace. The post-exposure analysis included SEM/EDS (WDS) and XRD. The surface roughness was determined by a contact and laser profilometer. The obtained results demonstrate that the mechanical surface preparation influences oxidation kinetics as well as the microstructure of the oxide scale formed on the alloy at both studied temperatures. Namely, polishing and grinding caused local formation of Fe-rich nodules and sub-layer of protective Al2O3. In contrast, gritblasting leads to the formation of a thick outer Fe-oxide and internal aluminum nitridation. A significant increase in the oxidation rate of the material after gritblasting was attributed to grain refinement in the near-surface region, resulting in an increase in easy diffusion paths, namely grain boundaries., Comment: Version of Record

The effects of surface preparations on oxidation kinetics and oxide scale morphology for the commercially available Ni-based superalloy IN 713C have been investigated. The ground and polished samples were exposed in air at 800-1100C. The ground specimens were found to demonstrate lower oxidation kinetics compared to those after polishing. The grinding also affected the oxide scale morphology, resulting in a protective alumina scale, while the polished samples developed Ni-/Cr-rich mixed oxides on the surface. Better oxidation resistance of the ground surfaces is related to a higher concentration of defects in the nearsurface region introduced by cold working. These defects facilitate the outward transport of the scaleforming element Al and thus are beneficial for protective oxidation. The oxidation mechanism at lower temperatures was introduced. The model based on the generalized Darken method and multiphase approximation was proposed., Comment: Version of Record

In the present paper, the analysis of polishing, grinding and sand-blasting processes on oxidation behavior of nickel, copper and nickel-copper alloy has been investigated. Surface roughness has been measured using two methods: by contact profilometer and by fractal analysis. It has been proved that sand-blasting process influences the surface roughness the most but also contaminates the surface with alumina particles. The oxidation tests were performed in thermogravimetrical furnace. The obtained mass gain plots, SEM microphotographs of cross-sections and SEM EDS analysis of the samples prove that surface preparation changes oxidation kinetics morphology of the polished and ground samples does not vary significantly after oxidation at investigated temperatures, but differences in oxide layer thicknesses and mass gains were observed. Oxidized sandblasted samples reveal that increased surface roughness and alumina intrusions change the oxidation process mixed Al (Ni, Cu or Ni-Cu) oxide is formed and separate Al2O3 particles are visible. The results prove that surface preparation influence high temperature oxidation of the samples by promoting new diffusion mechanism., Comment: The current version is identical in content with the peer-reviewed

In this paper the problem of determination of the diffusion coefficients in a ternary multiphase system is discussed. In the literature there is a lack of data concerning the approximation method which allows to determine diffusion coefficients in such complicated systems. We propose the mass conservation method (MCA) for calculation the diffusivities in phases where the differences in composition is linear. Only one experimental results is needed for determination of the diffusion data. The method is implemented and checked under ternary Ti-NiAl system - this system characterize occurrence three intermetallic phases in diffusion couple Ti-NiAl., Comment: the current version is identical in content with the peer-reviewed

In the present work surface roughness of copper samples after mechanical surface preparation processes (polishing, grinding, sand-blasting) and after exposure in non-oxidizing (high purity argon) and oxidizing (air) conditions at 700 and 750{\deg}C have been evaluated by contact profilometer and by fractal analysis. Quantitative description of surfaces that are hidden from the sight of conventional methods is possible by fractal analysis, e.g. in the present work, the roughness of Cu2O/Cu boundary has been evaluated under oxide layer. It has been pointed out, that in both oxidizing and non-oxidizing conditions initial surface roughness of copper is affected by annealing at high temperature: at 700{\deg}C surface roughness of polished and ground samples increased but at 750{\deg}C decreased in comparison to surface roughness prior to heat treatment. For sand-blasted samples in both oxidizing and non-oxidizing conditions the lowest values of surface roughness parameters were obtained at 750{\deg}C. It is then concluded that two phenomena are responsible for such effect: chemical reaction between copper and oxygen and surface diffusion of copper due to high temperature of annealing., Comment: the current version is identical in content with the peer-reviewed