Search

In order to reduce the ohmic losses in the slow wave structure (SWS), an elliptical pillar defected photonic crystal waveguide (EPDPCW) is proposed as a SWS for the terahertz traveling wave tube (TWT). Compared with rectangular pillar defected photonic crystal waveguides (RPDPCW), the EPDPCW shows better high-frequency characteristics and lower ohmic losses. According to the particle-in-cell (PIC) results, in the frequency range of 188 GHz to 218 GHz, the saturated output power of EPDPCW is greater than 13.4 W, and the maximum saturated output power is 26.8 W at 196 GHz at a voltage of 9.78 kV and a beam current of 150 mA. Compared to the RPDPCW-TWT, the performance of the EPDPCW-TWT has been significantly improved. [ABSTRACT FROM AUTHOR]

For the purpose of improving performance and reducing the fabrication difficulty of terahertz traveling wave tubes (TWTs), this paper proposes a novel single-section high-gain slow wave structure (SWS), which is named the symmetrical quasi-synchronous step-transition (SQSST) folded waveguide (FW). The SQSST-FW SWS has an artificially designed quasi-synchronous region (QSR) to suppress self-oscillations for sustaining a high gain in an untruncated circuit. Simultaneously, a symmetrical design can improve the efficiency performance to some extent. A prototype of the SQSST-FW SWS for 650 GHz TWTs is designed based on small-signal analysis and numerical simulation. The simulation results indicate that the maximum saturation gain of the designed 650 GHz SQSST-FW TWT is 39.1 dB in a 34.3 mm slow wave circuit, occurring at the 645 GHz point when a 25.4 kV 15 mA electron beam and a 0.43 mW sinusoidal input signal are applied. In addition, a maximum output power exceeding 4 W is observed at the 648 GHz point using the same beam with an increased input power of around 2.8 mW. [ABSTRACT FROM AUTHOR]

A new slow wave structure (SWS), named E-plane loaded sine waveguide (EPLSW) SWS is proposed for the development of G-band traveling wave tubes (TWTs). The structure, derived from the sine waveguide (SW) SWS, features staggered rectangular gratings on the two E-planes, intersecting with the sine-shaped gratings. The natural electron beam tunnel lies between these gratings. The EPLSW-SWS offers improved characteristics compared to the conventional SW-SWS. High-frequency simulation studies reveal that the passband of the EPLSW-SWS extends by more than 33 GHz over the SW-SWS under identical dispersion conditions. Additionally, the interaction impedance of EPLSW-SWS surpasses that of the SW-SWS in the frequency range of 195–255 GHz. Further analysis through particle-in-cell (PIC) results presents that when operating at 19.5 kV and 145 mA for the sheet beam current, it attains a maximum saturated power of 132.7W and a 3 dB bandwidth exceeding 50 GHz. [ABSTRACT FROM AUTHOR]

A staggered vane-shaped slot-line slow-wave structure (SV-SL SWS) for application in W-band traveling wave tubes (TWTs) is proposed in this article. In contrast to the conventional slot-line SWSs with dielectric substrates, the proposed SWS consists only of a thin metal sheet inscribed with periodic grooves and two half-metal enclosures, which means it can be easily manufactured and assembled and has the potential for mass production. This SWS not only solves the problem of the dielectric loading effect but also improves the heat dissipation capability of such structures. Meanwhile, the SWS design presented here covers a −15 dB S11 frequency range from 87.5 to 95 GHz. The 3-D simulation for a TWT based on the suggested SWS is also investigated. Under dual-electron injection conditions with a total voltage of 17.2 kV and a total current of 0.3 A, the maximum output power at 90 GHz is 200 W, with a 3 dB bandwidth up to 4 GHz. With a good potential for fabrication using microfabrication techniques, this structure can be a good candidate for millimeter-wave TWT applications. [ABSTRACT FROM AUTHOR]

In this paper, a novel staggered double-segmented grating slow-wave structure (SDSG-SWS) is developed for wide-band high-power submillimeter wave traveling-wave tubes (TWTs). The SDSG-SWS can be considered as a combination of the sine waveguide (SW) SWS and the staggered double-grating (SDG) SWS; that is, it is obtained by introducing the rectangular geometric ridges of the SDG-SWS into the SW-SWS. Thus, the SDSG-SWS has the advantages of the wide operating band, high interaction impedance, low ohmic loss, low reflection, and ease of fabrication. The analysis for high-frequency characteristics shows that, compared with the SW-SWS, the SDSG-SWS has higher interaction impedance when their dispersions are at the same level, while the ohmic loss for the two SWSs remains basically unchanged. Furthermore, the calculation results of beam–wave interaction show that the output power is above 16.4 W for the TWT using the SDSG-SWS in the range of 316 GHz–405 GHz with a maximum power of 32.8 W occurring at 340 GHz, whose corresponding maximum electron efficiency is 2.84%, when the operating voltage is 19.2 kV and the current is 60 mA. [ABSTRACT FROM AUTHOR]

In order to improve the performance of sine waveguide (SW) traveling wave tube (TWT), an elliptical beam-tunnel sine waveguide (EBTSW) slow wave structure (SWS) is proposed. EBTSW-SWS not only has high interaction impedance in a relatively wide frequency band but also has an elliptical beam-tunnel. The simulation results of high-frequency characteristics show that, under the same dispersion, the passband of EBTSW-SWS increases by 30% compared to the SW-SWS, and the average interaction impedance of EBTSW-SWS is higher than that of SW-SWS in almost the whole passband. Moreover, the particle-in-cell (PIC) simulation results reveal that under the operating voltage of 20.8 kV and beam current of 150 mA, EBTSW-TWT can provide more than 70 W of saturated output power in the frequency range of 200-260 GHz, reaching the maximum power of 151 W at 220 GHz with the maximum electronic efficiency of 4.85%. [ABSTRACT FROM AUTHOR]

This article studies and summarizes the operating characteristics of a ${G}$ -band folded waveguide traveling wave tube (TWT) amplifier enhanced by the $\pi $ -mode extended interaction cavities. Compared with conventional ${G}$ -band TWTs, the proposed amplifier can at once obtain a higher gain in a shorter interaction circuit length and ensure a proper operating bandwidth. The key of the design is introducing the $\pi $ -mode multigap resonant cavity with alternating wide and narrow slots, which will improve the working performance of the whole device by shortening the length of the interaction circuit, enhancing its interaction effect, and improving its gain of unit length. In this design, the operation bandwidth is expanded by stagger tuning technique. In addition, the influence of cavity loss is examined so that the optimal performance is achieved. The PIC simulation results show that when the operating voltage is 21 kV and the operating current 80 mA, the maximum average output power of the designed TWT amplifier is 65.78 W at 217.4 GHz, which is corresponding to the maximum gain and efficiency of 37.38 dB and 3.9%, respectively. The gain per unit length is 12.64 dB/cm and the 3-dB bandwidth is 3.5 GHz. [ABSTRACT FROM AUTHOR]

Enormous concerns focus on the high-power and wide bandwidth traveling-wave tube (TWT) for its outstanding performance. In this article, a shape-optimized staggered double-vane slow-wave structure (SWS) for terahertz (THz) sheet beam TWT is proposed. The shape-optimized staggered double-vane SWS takes the advantages of higher interaction impedance, lower transmission loss, and lower phase velocity than conventional staggered double-vane SWSs. The shape-optimized staggered double-vane SWS with 85 periods is designed, fabricated, and cold tested. The measured transmission loss of the shape-optimized staggered double-vane SWS is less than 0.79 dB/cm in the frequency range of 0.211–0.26 THz, which is in good agreement with the simulation results. Furthermore, the beam–wave interaction analysis of a sheet beam TWT with this SWS is given. The output power is predicted to be >100 W with 3-dB bandwidth of >50 GHz. The results show that the shape-optimized staggered double-vane SWS is a very promising scheme to construct a high-power and wideband THz TWT for future applications such as communication and imaging. [ABSTRACT FROM AUTHOR]

A $Q$ -band traveling-wave tube (TWT) with profiled helix pitches and profiled inner diameters of slow wave structure (SWS) is proposed. The transmission characteristics of the $Q$ -band TWT are simulated by the Computer Simulation Technology (CST). In the operating frequency band (36.5–41.5 GHz), the simulated voltage standing wave ratio (VSWR) is less than 1.5. In addition, the beam–wave interaction is simulated to predict the performance of the $Q$ -band TWT when the beam voltage and beam current are 8.5 kV and 60 mA, respectively, and the axial focusing magnetic field is 0.4 T. In the operating frequency band, the self-oscillation is well suppressed, and the device efficiency of the $Q$ -band TWT exceeds 63.5%, and the saturated output power and gain exceed 83 W and 45 dB, respectively, especially the device efficiency can reach the maximum of 69.5% at 37 GHz. When it is backed off 6 dB from the saturation, the device efficiency exceeds 40.5%, up to 42.7% at 39 GHz. Preliminary experiments have confirmed the design. These results show that the proposed $Q$ -band TWT has important applications to the next generation wireless communication system with high efficiency. [ABSTRACT FROM AUTHOR]

The angular log-periodic meander-line traveling wave tube (TWT) is a kind of low voltage, small-sized, high power, low cost, on chip amplifiers, and considered as a key part of the advanced communication systems, the future biomedical applications and the next electronic counter measure (ECM) instruments et al. Here, an angular log-periodic meander-line TWT is presented in this article. The angular log-periodic meander-line slow wave structure (SWS) is supported by two diamond rods. The dispersion and the impedance characteristics are analyzed in detail. In order to reduce the reflection loss, a gradual ridged waveguide is connecting the input–output standard rectangular waveguide to the meander-line SWS. The particle in cell (PIC) simulations show that the output power of the TWT can reach 55 W at 34 GHz with the operation voltage of 1800 V and the beam current of 0.2 A. The SWS is manufactured by a laser machine with Molybdenum sheet. The assembled TWT is tested and the results show that the ${S}_{{11}}$ is less than −10 dB at 30–39 GHz. The ${S}_{{21}}$ mismatch between the simulated and the measurement is discussed at the end. [ABSTRACT FROM AUTHOR]

A novel electron-optical system (EOS) for ${G}$ -band traveling-wave tubes (TWT) is investigated by simulation and verified by experiment. The EOS includes a sheet beam electron gun, a tunable periodic cusped magnetic focusing (TPCMF), and a collector. An elliptical focus electrode (FE) featuring a simple geometry and easy fabrication is utilized to compress the pencil beam into the sheet beam with a cross section of 0.4 mm $\times0.1$ mm. The electron gun with a cylindrical cathode of 0.8 mm diameter generates the sheet beam with voltage of 22 kV and current of 115 mA. Based on the sheet beam electron gun, the TPCMF with easy assembly and compact size is then proposed. The experimental results show that the beam transmission is 92.1% within a beam tunnel (its length 21.2 mm and cross section 0.8 mm $\times0.15$ mm). The EOS is suitable for ${G}$ -band TWT. [ABSTRACT FROM AUTHOR]

In this article, we propose a simulation method to investigate the noise mechanism of traveling-wave tube (TWT). Based on the nonlinear theory of Lagrangian description, 1-D noise model is established to analyze the shot noise and the velocity noise of the electron beam in the drift space, which clearly shows that the beam noise propagates along the electron beam with standing wave shape. The shot noise and the velocity noise can be periodically converted into each other along electron beam transmission, which is consistent with the prediction of the classical noise theory developed by Pierce and Danielson (1954). Using the nonlinear beam–wave interaction theory, the evolution process of the shot noise and the velocity noise of the electron beam transforming to the electromagnetic wave in TWT is illustrated. The calculated results show that the input position of the slow wave circuit may affect the noise power spectral density (NPSD) of the device. The proposed method can provide more intuitive and simple images to explain the noise mechanism of TWT. [ABSTRACT FROM AUTHOR]

In this article, an improved model for the beam–wave interaction of sheet beam in traveling wave tubes (TWTs) considering ohmic losses and reflections is presented. The ohmic losses are obtained by field analysis and equivalent method. The space charge magnetic field is derived from the active Helmholtz’s equation. An algorithm to obtain the S-matrix by the equivalent circuit method is presented. The relativistic Boris method is applied to accelerate macroparticles. The exchanged power is computed by the work the electromagnetic field applied to the macroparticles. The theoretical model is applied for validation to a G-band staggered double vane TWT and validated in comparison with CST Particle Studio and simulations without losses and reflections. The convergence of this algorithm is also discussed. The simulation time of the model is substantial faster than 3-D particle-in-cell (PIC) simulations. [ABSTRACT FROM AUTHOR]

A novel electron-optical system is proposed for dual azimuthally stacked radial sheet electron beams (ARSEBs). The two sheet beams are emitted from curved surfaces of two cathodes and are focused by a focusing electrode, which is carefully designed to produce a symmetric field distribution for the two beams and to avoid interference between the beams. A common tunable periodic cusped magnetic focusing system is also designed to focus the two ARSEBs. The dual sheet beams are used in a traveling wave tube (TWT) consisting of a cascade of two azimuthally supported angular log-periodic strip-line (ASALS) slow-wave structures (SWSs). The transmission efficiency in the presence of beam–wave interaction is 93%. The particle-in-cell simulation results show that for a beam voltage of 4400 V and a current of 0.39 A, the proposed cascaded TWT has a maximum gain of 32.5 dB at 35 GHz and a maximum output power of 180 W; this is a significant gain improvement over a TWT using a single ASALS SWS. [ABSTRACT FROM AUTHOR]

A novel sine groove waveguide slow wave structure (SGW-SWS), originated from the sine waveguide (SW), is proposed for a wideband terahertz (THz) traveling wave tube (TWT). SGW-SWS not only has high interaction impedance in a relatively wide frequency band, but also has a wide beam tunnel. In addition, it can be fabricated using the Nano-Computer Numerical Control (CNC) milling techniques. The high-frequency simulation results show that, under the same dispersion, the passband of SGW-SWS is 23 GHz wider than that of SW-SWS, and the average interaction impedance of SGW-SWS is higher than that of SW-SWS in the whole passband. And the transverse dimension of beam tunnel is independent of the dispersion characteristics of SGW-SWS, so the beam current can be further increased by enlarging the size of beam tunnel. Moreover, the particle-in-cell (PIC) simulation results reveal that the saturated power and electronic efficiency of SGW-TWT in the frequency range of 201–260 GHz are more than 84.9 W and 2.72%, respectively, when the operating voltage is 20.8 kV and the beam current is 150 mA. [ABSTRACT FROM AUTHOR]

In this article, a novel dielectric-supported staggered dual-meander-line (DS-SDML) planar slow-wave structure (SWS) is proposed for a traveling wave tube (TWT) working at ${E}$ -band. The proposed staggered arrangement of meander-lines (MLs) leads to a stronger beam–wave interaction and achieves higher output power as compared to the symmetric arrangement. The input–output couplers have been designed by using staggered stepped double ridge waveguide, to connect the standard ${E}$ -band rectangular waveguide and the DS-SDML SWS. An attenuator and pitch tapering have been applied to the proposed SWS to suppress the unwanted frequencies and to improve the output power. Particle-in-cell (PIC) simulation results show that for an 11.8-kV, 200-mA sheet-beam, the output power can reach 283 W at 75 GHz, with a maximum gain and electronic efficiency of 34.5 dB and 11.9%, respectively. [ABSTRACT FROM AUTHOR]

The miniaturized traveling wave tube (TWT) is a kind of high-efficiency, high-power, long-lifetime power amplifier which is an attractive choice for many applications, such as outer space exploration, phased array radar detection, unmanned aerial vehicle (UAV) communication, and on-chip application. In this article, a sheet beam miniaturized TWT with V-shaped meander-line slow wave structure (SWS) supported by two trapezoidal ceramic rods is designed. First, the dispersion characteristics, the impedance characteristics, and the S-parameters of the V-shaped meander-line SWS are analyzed in detail. Then, the particle-in-cell (PIC) simulation results predict that the TWT can produce 512-W output power driven by a 7.1 kV, 0.3-A sheet beam with a rectangular cross-sectional area of 3.5 mm $\times0.1$ mm. The TWT can cover the whole ${X}$ -band when the operation voltage shift from 7.1 to 9.1 kV. At last, the V-shaped meander-line SWS is manufactured, assembled, and tested. The good agreement between the simulated and the measured ${S} _{\mathbf {11}}$ has been achieved and the mismatch between the simulated and the measured ${S} _{\mathbf {21}}$ has been discussed at the end. [ABSTRACT FROM AUTHOR]

The microstrip meander-line traveling wave tube (TWT) is a kind of small sized, low voltage, low cost, and easy to fabricate TWT. It is an attractive choice for many applications, such as communication systems, phased array radars, security detectors, and electronic counter measure (ECM) instruments. In this paper, a Ka band U-shape meander-line slow wave structure (SWS) supported by a diamond rod is presented. The dispersion characteristics of this meander-line SWS are analyzed using CST MW Studio. The S-parameter simulation results show that the reflection is below − 15 dB between 32 and 38 GHz, and the particle-in-cell (PIC) simulation reveals that this meander-line TWT can produce 57 W output power at 36 GHz, when it is driven by a 8.1 kV, 0.04 A sheet beam with rectangular cross-sectional area of 1.0 mm × 0.12 mm. This meander-line SWS is manufactured, assembled, and tested. The good agreement between the simulated and measured S11 has been achieved and the mismatch between the simulated and measured S21 has been discussed at the end. [ABSTRACT FROM AUTHOR]

A dual-beam planar slow wave structure (SWS), named dielectric supported ring-bar SWS is proposed in this paper. The planar SWS is supported by two dielectric rods at the side edges, making it fit for dual sheet beam operation. The high frequency and transmission characteristics of the proposed SWS are investigated. The backward-wave oscillation and higher harmonic waves are effectively suppressed by setting two cathodes in the same plane parallel to the SWS and negative phase-velocity jumping. The hot performance of the proposed SWS is carried out by using particle-in-cell (PIC) simulation, in which two sheet electron beams (9.7 kV, 0.2 A) are employed to provide direct current power. With an input power of 1W, the output power is 180 W at 38 GHz and the corresponding gain is 22.6 dB. Besides, after adding dielectric rods to the output part, the entire structure dissipates heat well by thermal analysis. [ABSTRACT FROM AUTHOR]

A novel slow wave structure (SWS), named staggered double corrugated waveguide (SDCW), is proposed for the development of wideband high-power terahertz (THz) traveling wave tubes (TWTs). The SDCW-SWS not only has the wideband characteristic of staggered double grating (SDG) but also has the high interaction impedance characteristic of symmetrical double grating. In addition, its tunnel width is independent of the lower cutoff frequency and can be further increased. Numerical Eigen mode calculations show that, under the same dispersion, the passband of SDCW-SWS is increased by more than 10 GHz compared with SDG-SWS, and the average interaction impedance at 195 GHz is increased by about 62%. A particle-in-cell simulation analysis confirms that the average output power, saturated gain, and electron efficiency of SDCW-TWT at 195 GHz are ~110 W, ~20.34 dB, and ~5.46%, respectively, when the operating voltage is 20 kV and the beam current is 100 mA. Therefore, SDCW is a promising slow wave circuit of wideband high-power THz traveling wave amplifier. [ABSTRACT FROM AUTHOR]

A novel modified angular log-periodic folded waveguide slow wave structure (MALPFW-SWS) is proposed for high-gain traveling wave tubes (TWTs). Each unit of the MALPFW-SWS has different dispersion characteristics and thus it has the ability to suppress oscillations in TWTs. The dispersion equation of the MALPFW-SWS is derived and a Ka-band MALPFW-SWS is designed according to the dispersion equation for verification. The particle-in-cell (PIC) simulation indicated that the output signal is steady even the gain of the designed MALPFW-TWT reaches 40 dB. The frequency spectrum of the output signal also proved that the MALPFW-SWS can suppress oscillations. The cold test experiment results show that the transmission characteristics of the fabricated MALPFW-SWS are good and are in good agreement with the simulation results. [ABSTRACT FROM AUTHOR]

A novel Ka-band azimuthal supported angular log-periodic strip-line (ASALS) slow wave structure (SWS) is proposed for a miniature radial sheet beam traveling wave tube (TWT). In the proposed SWS, two dielectric rods are employed to support the ASALS at both azimuthal sides. The strip-line is made of high-melting metal; thus, the ASALS SWS has a higher power capacity than microstrip SWSs. The high-frequency characteristics of that proposed SWS are investigated by using simulation software. The ASALS SWS is then fabricated and assembled for cold test. The measured transmission loss and reflection loss are better than − 2.5 dB and − 10 dB, respectively. The hot performance of the proposed is studied based on particle-in-cell (PIC) simulation. It is shown that when the operating voltage is 5700 V, the ASALS TWT can give a maximum output power of 320 W at the frequency of 39 GHz, corresponding to a gain of 14.9 dB and electron efficiency of 9.12%. [ABSTRACT FROM AUTHOR]

Traveling wave tube (TWT) is an attractive solution for wideband and high-power sources or amplifiers in the terahertz (THz) band. In this article, a novel slow-wave structure (SWS) for TWT, named double tunnel sine waveguide (DTSW), which is based on sine waveguide (SW), is proposed. The following key technologies are adopted: 1) the rectangular holes, at which the operating mode is cutoff, are alternately opened on the sine-shaped ridges to form two electron beam tunnels and 2) the lower surface of rectangular holes is flush with the top of sine-shaped ridges. Compared with the SW-SWS, DTSW-SWS has the wider operating band and higher interaction impedance under the condition that the phase velocity of the two SWSs is at the same level. In addition, DTSW-SWS is simple in structure and easy to fabricate. The particle-in-cell simulation results reveal that DTSW-TWT has an output power of more than 202 W in the frequency range of 202–255 GHz with the maximum power of ~405 W and electron efficiency of ~9.8% at 215 GHz, under the operating voltage of 23 kV and beam current of 180 mA. Therefore, the DTSW should be considered as a promising SWS for the high-power and wideband THz traveling wave amplifier. [ABSTRACT FROM AUTHOR]

A large signal beam-wave interaction model for the analysis of folded waveguide traveling wave-tube (FWG TWT) is proposed. The slow-wave structure is modeled as a sequence of coupled resonant cavities. The electron beam is treated as a current source that can induce electromagnetic waves in the cavity. The beam-wave interacting process is modeled as an active matrix. Compared with the other models only calculating the in-band characteristic of FWG TWT, our model can provide characteristic analysis in both in-band and near cutoff regions, and thus broaden operating bandwidth and suppress oscillation. As verification, two FWG TWT examples were designed by using our model. Its performances predicted by our code agree well with that obtained by the experiment and particle-in-cell software, respectively. [ABSTRACT FROM AUTHOR]

In this paper, a novel angular log-periodic folded groove waveguide (ALFGW) slow-wave structure (SWS) has been investigated theoretically and experimentally for application in Ka-band traveling-wave tubes (TWTs). The dispersion relation for the ALFGW is derived analytically, and the dispersion characteristics are calculated for a Ka-band design. The designed SWS is fabricated using oxygen-free-copper that is silver electroplated. The measured cold-test parameters show good agreement with the simulation results, with S21 varying from −2.7 dB to −4.8 dB and S11 better than −13.6 dB over the frequency range of 30–38 GHz. Simulations of beam–wave interactions using a 4850 V and 0.4 A sheet beam with a high aspect ratio of 28:1 indicate an output power of 128 W, corresponding to a maximum gain and electronic efficiency of 18.1 dB and 6.6%, respectively. Due to the log-periodic form, a higher output power, higher efficiency, wider bandwidth, and lower operating voltage are achieved as compared to a TWT based on the conventional folded groove waveguide (FGW) SWS. These results show that the proposed ALFGW SWS has good potential for application in relatively high-power wideband TWTs. [ABSTRACT FROM AUTHOR]

A novel slow wave structure (SWS), called double tunnel staggered grating (DTSG), which originates from the double staggered grating (DSG) and folded waveguide (FW), is proposed to develop a dual-beam traveling wave tube (TWT) with high power and electron efficiency in Terahertz (THz) band. Using two key techniques: (1) the rectangular holes are opened in the grating-ridges, and the operating mode is cut-off at holes; (2) specific grating-height, the DTSG-SWS possesses the wide operating band as DSG-SWS, high interaction impedance as the rectangular grating (RG) SWS, and good transmission characteristics as FW-SWS. In addition, it is not only suitable for the dual-beam TWT, but also is simple and easy of fabrication as DSG-SWS. The particle-in-cell simulation analysis confirms that the saturated power and electron efficiency of TWT using DTSG-SWS have been significantly improved compared with the TWT using DSG-SWS. [ABSTRACT FROM AUTHOR]

In order to further improve the output power of W-band traveling wave tube (TWT), a low gain TWT was proposed as a secondary amplifier. It uses a double staggered grating slow wave structure (DSG-SWS) and a sheet beam. Firstly, the design of DSG-TWT was given. Through simulation, the DSG-TWT could provide a saturation output power of more than 1000 W in the frequency range of 93–97 GHz, and the maximum output power could reach 1200 W at 95 GHz. No oscillation and current interception were found. Then DSG-SWS was fabricated by E-plane partition method using high-precision CNC milling. The SWS was fed with a high-power input-output coupler which consists of a mode converter and an impedance transformer. Simulation and cold-test results were presented, showing that the S11 is less than −10 dB and the voltage standing wave ratio (VSWR) is less than 2.0 in the frequency range of 93–100 GHz. [ABSTRACT FROM AUTHOR]

A novel helical groove rectangular waveguide slow wave structure (HGRW-SWS) which evolves from the double staggered grating waveguide (DSGW) SWS is put forward to develop the high-gain and high electron efficiency terahertz (THz) traveling wave tube (TWT). The major advantages of the HGRW SWS are the higher interaction impedance, lower ohmic loss, and lower phase velocity especially in higher frequency band compared with the DSGW SWS. The gain and electron efficiency of TWT using HGRW-SWS have been significantly improved, respectively, compared with the TWT using DSGW-SWS. [ABSTRACT FROM AUTHOR]

High-power vacuum electron devices (VEDs) are attractive, because of their broad applications, such as advance radars, electromagnetic warfare, and plasma reactors. In this paper, a Ka band mega-watt sheet electron beam traveling wave tube (TWT) is reported. A two-staged rectangular waveguide grating slow wave structure (SWS) driven by a sheet electron beam (20 mm × 1 mm, 164.8 kV, 850 A, 20 ns) is used in this TWT. In order to suppress the self-excited oscillation, a rectangular BeO attenuator is inserted between the two-staged SWSs. The experimental results show that the TWT can produce more than 2 MW output power from 34.2 to 35.5 GHz. And the maximum output power is 4.24 MW at 35 GHz, corresponding to the gain of 25.9 dB. In the future, the TWT will be used to perform research on biomedical effects and imaging. [ABSTRACT FROM AUTHOR]

This paper puts forward a novel dual-beam overmoded folded waveguide (FW) slow-wave structure (SWS), which is loaded with photonic crystals. In this novel structure, the two electron beams pass through the small gaps between the photonic crystal structures and the FW; the dimension of the FW is twice larger than that of the fundamental mode structure. The novel dual-beam photonic crystal overmoded FW traveling-wave tube (TWT) is proposed on the basis of the SWS. And, a mode converter is introduced to achieve the connection between the SWS and the input/output structure, and the mode transformation. At the operating voltage of 21.2 kV and the operating current of 320 mA, the proposed TWT can generate 128 W of output power at 220 GHz, and its 3-dB bandwidth is 7 GHz, ranging from 216 to 223 GHz. [ABSTRACT FROM AUTHOR]

In this paper, a stacked dual beam electron gun and the associated electron optical system are proposed. The stacked dual beam electron gun includes two compact focusing electrodes which help to achieve dual sheet beams. As an application of this dual beam electron gun, a 340 GHz integrated dual beam traveling wave tube (TWT) based on the staggered dual vane slow-wave structure (SWS) is also put forward. In order to reduce the length of the TWT, a novel input/output coupler is introduced. The overall transmission characteristics of the SWS structure together with the input/output couplers show a wide bandwidth covering a frequency range of 306 GHz to 360 GHz. Based on the parameters obtained for the integrated TWT, a stacked dual-beam electron gun with dual focusing electrodes is designed to achieve a beam current of 43 mA, a beam voltage of 21.4 kV, and a cross-sectional size of each beam of 0.3 mm × 0.08 mm. A uniform magnetic field of 0.52 T is utilized to focus the dual electron beams, and a beam transmission efficiency of 97.1% is achieved over a length of 50 mm. Finally, particle in cell simulation results show that the integrated dual-beam TWT can generate an output power of 5 W over the frequency range of 315 GHz to 350 GHz, with the maximum output power of 24.5 W at 330 GHz. [ABSTRACT FROM AUTHOR]

Variable-width technology applied to the folded waveguide traveling wave tube (FW-TWT) is proposed in this paper to suppress the lower band-edge oscillation and to expand the operating bandwidth when the operating frequency shifts toward the lower band for obtaining larger output power. Changes in the width of the slow wave structure (SWS) determine the variation of the lower-cutoff-frequency (LCF), which makes the LCF's distribution a frequency range rather than a specific frequency-point. The lower band-edge oscillation will not be focused on a special position but distributed in a frequency-band range in which multiple oscillation modes compete with each other near the LCF. The lower band-edge oscillation can be suppressed by mode competition to some extent. In addition, the width variation of SWS also results in the phase-velocity variation, and thus, the operating bandwidth of FW-TWT can be further improved by the optimized design of variable-width-SWS parameters. Beam-wave interaction simulations predicted that power and bandwidth improvements have been achieved without the lower band-edge oscillation. Meanwhile, four solutions are given for further certifying the effectiveness of the variable-width method in lower band-edge oscillation suppression and bandwidth widening. An output power level of over 350 W in a frequency range of 85–90 GHz (5 GHz) is obtained, with a maximum power of ∼648 W and an electron efficiency of ∼12.1% at 88 GHz with a beam current of 260 mA and a beam voltage of 20.5 kV. [ABSTRACT FROM AUTHOR]

A dual-beam planar dielectric-rod-support uniform metallic meander line slow-wave structure (SWS) for high-efficiency Ka-band traveling wave tube (TWT) is proposed in this paper. Two dielectric rods are placed on both sides of metallic meander line to support it, instead of the dielectric substrate in the conventional microstrip meander line. Furthermore, it can not only solve the problem of the electron charge accumulation on microstrip but also leads to a bigger interaction impedance. According to particle-in-cell simulation results, a dual-sheet-beam planar dielectric-rod-support uniform metallic meander line TWT can get an output power of 330.2 W at 38 GHz under the case of 10.6 kV beam voltage and 0.2 A beam current. The corresponding maximum gain and electron efficiency are 23.4 dB and 15.5%, respectively, where the length of whole SWS is only 20 mm. [ABSTRACT FROM AUTHOR]

A high-harmonic traveling-wave tube (HHTWT) is designed, developed, and tested in this paper. This device is configured as a multiplier–amplifier with Q-band input signals and its third harmonic, i.e., D-band output power. The tested result demonstrates that 280 mW at 133.5 GHz is obtained as a result of 200 mW at 44.5-GHz input signal. The simulation and experiment validate that the high-harmonic radiation can be generated and amplified in the HHTWT. The approach described in this paper could find application in exploring high power, wideband tunable terahertz source. This paper is expanded from a conference paper on IVEC 2017. The detail design produce and tested result are added in this paper. The explanation of the simulation and tested results is also presented. [ABSTRACT FROM AUTHOR]

A Ka-band sheet electron beam (SEB) traveling-wave tube (TWT) based on three-slot staggered-ladder (TSTL) coupled-cavity slow-wave structure (CC-SWS) is proposed. The high-frequency characteristics of TSTL SWS were analyzed in detail. A well-matched input/output coupling system that solves the problem of energy coupling between the SWS and the external circuit was designed. A new method of loading the distributed attenuator for TSTL SWS was investigated for suppressing backward wave oscillation effectively. In addition, a SEB gun which can produce the SEB conveniently was optimized. A small tunable periodic cusped magnet (STPCM) system was designed to focus the low voltage, high-current SEB, which decreases the whole dimension of the TWT sufficiently. Moreover, the special STPCM system is predicted to exhibit 100% beam transmission efficiency. Finally, the beam-wave interaction was studied. The results obtained by CST simulation show that the SEB TWT can produce output power over 5 kW within the bandwidth ranging from 31.5 to 35.5 GHz, and the maximum output power is 10.15 kW at 33 GHz, corresponding electron efficiency of 10.36%. The fabrication of the device is under way. [ABSTRACT FROM PUBLISHER]

A 140-GHz folded-waveguide traveling wave tube (FWG-TWT) with a relatively larger circular electron beam tunnel was designed and developed. Using simulation software, the high frequency characteristics, the transfer characteristics, and the beam-wave interaction of the TWT were studied in detail. The simulation predicted up to 98 W output power and about 43 dB gain of FWG-TWT at the center frequency. The input and output couplers compatible with the FWG-SWS and the periodic permanent magnet focusing structure were designed. The FWG-TWT thus designed was fabricated and tested. The experimental result shows the output power exceeding 1.6 W and the gain exceeding 25 dB at 140 GHz when the input power is 5 mW. The reasons for the departure of the experimental from the simulated results have been explained. [ABSTRACT FROM PUBLISHER]

The symmetrical microstrip angular log-periodic meander-line (ALPML) slow-wave structure (SWS), which is suitable for Ka-band low-voltage traveling-wave tubes, is described in this paper. The dispersion characteristics and coupling impendence of this kind of SWS are achieved by simulation. A radial uniform magnetic field of 0.4 T is developed using radially magnetized permanent magnets to focus the radial sheet electron beam. To exploit the potentialities of the symmetrical ALPML SWS, the beam–wave interaction is carried out with a radial convergent and a divergent sheet electron beam. For the radial divergent electron beam with a voltage of 791 V and a current of 0.3 A, an output power over 60 W with an electron efficiency of 26% at 30 GHz is achieved from particle-in-cell simulation. The effects of misalignments and phase mismatches are carried out at the end. [ABSTRACT FROM AUTHOR]

In order to alleviate the problem of achieving large powers beyond 10 kW at frequencies as high as 220 GHz, a two-stage, two-sheet-beam relativistic TWT (SBRTWT) was proposed. For one-stage SBRTWT, there exists instability phenomenon as the effect of electron noise will become large enough compared with the small input power. To avoid the effect, the gain of the first-stage tube was decreased, and its output power was employed to drive the second-stage tube. A large-width branch-guide energy coupler was proposed, analyzed and designed, which can solve the difficult problem to couple the amplified microwave from a wide waveguide to another wide waveguide. A two-beam SBRTWT of 70 kW output with a gain of 28.5 dB was predicted. The findings establish that the two-stage configuration provides larger output powers than the single-stage configuration of SBRTWT and call for further research in two-stage SBRTWT. [ABSTRACT FROM PUBLISHER]

In this paper, a high-power Ka-band traveling-wave tube (TWT) driven by a sheet electron beam is proposed and demonstrated by means of the simulation and experimental methods. The single grating rectangular waveguide with large width-to-height ratio is used as the slow-wave structure (SWS). An $E$ -plane bend energy coupler is put forward to feed this wide SWS. An irregular transition structure between the input waveguide and the SWS is suggested and designed, which is beneficial to suppress the self-excited oscillation. For a practical electron beam (20 mm $\times \,\, 1$ mm, 150.1 kV, 850 A, and 20-ns), the output power of this single rectangular grating sheet beam TWT is larger than 750 kW from 34.5 to 35.4 GHz. The maximum power is 1.21 MW at 35 GHz, corresponding to a gain of 20.4 dB. [ABSTRACT FROM PUBLISHER]

In this paper, a novel small tunable periodic cusped magnet (NSTPCM) system is proposed for the purpose of realizing low voltage, big current sheet electron beam propagation in a long distance in engineering, which is composed of a series of position-fixed magnet blocks in alignment and freely sliding staggered pole pieces. This kind of NSTPCM not only generates higher magnetic field in the axial direction but also realizes more convenient adjustment of magnetic field in the transverse direction. This NSTPCM system has been successfully applied in a Ka-band sheet electron beam staggered double vane traveling wave tube. The tested sheet beam transmission efficiency is $>93$ % in a 112.7-mm-length slow-wave structure under the condition of beam voltage 24.3 kV and beam current 0.8 A. Moreover, the measured output power is $>75$ W in the range from 33 to 37.5 GHz, and the maximum output power is 128 W at 34 GHz. This paper provides the foundation for the development of sheet electron beam vacuum devices. [ABSTRACT FROM PUBLISHER]

In this paper, a wideband 220-GHz sheet-beam traveling-wave tube (TWT) based on staggered double vane slow-wave structure (SWS) is investigated. A novel method of loading the attenuator into the SWS for suppressing backward wave oscillation is proposed. In addition, a novel focusing electrode of the sheet beam gun is carried out in this paper, which is a whole structure but divided into two parts artificially, one is used to compress the electron beam in $X$ -direction and the other is used to compress the electron beam in $Y$ -direction. In addition, a novel anode is redesigned to reduce the defocusing effect caused by the equipotential surfaces. A nonuniform periodically cusped magnet is used for focusing the sheet electron beam, which is predicted to exhibit 100% beam transmission efficiency in a 75-mm length drift tube. The high-frequency characteristics of the SWS and the beam-wave interaction are also studied. The results reveal that the designed TWT is expected to generate over 78.125-W average power at 214 GHz, and the 3-dB bandwidth is 31.5 GHz, ranging from 203 to 234.5 GHz. [ABSTRACT FROM PUBLISHER]

A phase shift that is caused by the machining errors of independent circuits would greatly affect the efficiency of the power combination in traditional multi-beam structures. In this paper, to reduce the influence of the phase shift and improve the output power, a multi-beam shunted coupling sine waveguide slow wave structure (MBSC-SWG-SWS) has been proposed, and a multi-beam overmoded flat-roofed SWG traveling wave tube (TWT) based on the MBSC-SWG-SWS was designed and analyzed. A TE10-TE30 mode convertor was designed as the input/output coupler in this TWT. The results of the 3D particle-in-cell (PIC) simulation with CST software show that more than a 50 W output power can be produced at 342 GHz, and the 3 dB bandwidth is about 13 GHz. Furthermore, the comparison between the single-beam sine waveguide (SWG) TWT and the multi-beam overmoded SWG TWT indicates that the saturated output power of the multi-beam overmoded SWG TWT is three times more than that of the single beam SWG TWT. [ABSTRACT FROM AUTHOR]

An attenuator supporting meander-line (ASML) slow wave structure (SWS) is proposed for a Ka-band traveling wave tube (TWT) and studied by simulations and experiments. The ASML SWS simplifies the fabrication and assembly process of traditional planar metal meander-lines (MLs) structures, by employing an attenuator to support the ML on the bottom of the enclosure rather than welding them together on the sides. To reduce the surface roughness of the molybdenum ML caused by laser cutting, the ML is coated by a thin copper film by magnetron sputtering. The measured S11 of the ML is below −20 dB and S21 varies around −8 dB to −12 dB without the attenuator, while below −40 dB with the attenuator. Particle-in-cell (PIC) simulation results show that with a 4.4-kV, 200-mA sheet electron beam, a maximum output power of 126 W is obtained at 38 GHz, corresponding to a gain of 24.1 dB and an electronic efficiency of 14.3%, respectively. [ABSTRACT FROM AUTHOR]