Search

Objectives 3D printed polymeric film intended for topical delivery of berberine (BBR) was developed using stereolithography (SLA) to enhance its local concentrations. PEGDMA was utilized as photopolymerizing resin, with PEG 400 as an inert component to facilitate BBR solubilization and permeation. Methods Three batches of topical films were printed by varying resin and PEG 400 compositions. In-vitro physicochemical characterizations of the 3D printed films were performed using several analytical techniques including ex-vivo drug permeation studies. In-vivo skin irritation studies were also conducted to assess the skin irritation potential. Key findings Films were 3D printed according to design specifications with minimal variations. Microscopic analysis confirmed 3D architecture, while thermal and X-ray diffraction studies revealed amorphous BBR entrapment. Drug permeation study showed effective ex-vivo diffusion up to 344.32 ± 61.20 µg/cm2 after 24.0 h possessing a higher ratio of PEG 400. In-vivo skin irritation studies have suggested the non-irritant nature of printed films. Conclusions Results indicated the suitability of SLA 3D printing for topical application in the treatment of skin diseases. The presence of PEG 400 in the printed 3D films facilitated BBR diffusion, resulting in an improved flux in ex-vivo model and non-irritant properties in vivo. [ABSTRACT FROM AUTHOR]

This work focuses on the extrusion of a brittle, tacky, cationic copolymer i.e. Eudragit® E-100 to prepare filament and subsequent 3D printing of hollow capsular device using the extruded filament. An optimum amount of talc and triethyl citrate was used for the possible extrusion of the polymer. There was no thermal and chemical degradation of the polymer observed after extrusion confirmed by DSC and FTIR analysis. Microscopic analysis of the printed capsule showed the layer-by-layer manner of 3D printing. Capsule parts were printed according to the set dimensions (00 size) with minimal deviation. Printed capsule showed the soluble behaviour in gastric fluid pH 1.2 where within 15 min the encapsulated drug encounters with the dissolution medium and almost 70% drug was dissolved within 4 hr. In case of phosphate buffer pH 6.8, the printed capsule showed a longed swelling behaviour up to 12 hr and then gradually bursting of capsule occurred wherein more than 90% encapsulated drug was dissolved within 36 hr. Enteric coating of the printed capsule showed similar behaviour in alkaline medium that observed with non-enteric capsule. This indicates the potential application of this printed capsules for both gastric and intestinal specific delayed drug delivery by a single step enteric coating process. [ABSTRACT FROM AUTHOR]

In this work, hot-melt extrusion (HME) is coupled with fused deposition modeling (FDM) mediated 3D printing to demonstrate additive manufacturing to fabricate immediate release (IR) prototypes of olanzapine with the aim of enhanced solubility using a fast disintegrating polymer (Kollicoat® IR). Drug-polymer solubility and interaction parameters were estimated by Hansen solubility parameters and Hildebrand–Scott equation. The obtained values signified drug–polymer miscibility. The detailed in vitro physicochemical evaluations of the developed filament through HME and its derived 3D printed tablet by FDM technique were assessed thoroughly by several analytical means such as light microscopy, DSC, XRD, FT-IR, SEM, etc. The average disintegration time of this developed 3D printed IR tablet was found to be 63.33 (±3.6) sec complying with the USP limit. Additionally, in vitro dissolution study data revealed almost close correlations and both showed 100% of drug release within 15 min, thus complying with the definition of IR tablet. Thus, this study demonstrates the feasibility of directly using olanzapine-Kollicoat® IR through the HME process without the addition of any plasticizers, organic solvents, etc. and coupling of HME with 3D printing technology allowing prototypes of IR tablet of olanzapine. [ABSTRACT FROM AUTHOR]

Stereolithography (SLA) 3D printing of pharmaceuticals suffers from the problem of light scattering, which leads to over-curing, resulting in the printing of objects that are non-compliant with design dimensions and the overloading of drugs. To minimize this problem, photoabsorbers such as tartrazine (food grade) can be used to absorb the stray light produced by scattering, leading to unintended photopolymerization. Ghost tablets (i.e., non-erodible inert matrices) were additively manufactured using SLA with varying ratios of polyethylene glycol diacrylate (PEGDA): polyethylene glycol (PEG) 300, along with tartrazine concentrations. The 3D printed ghost tablets containing maximum (0.03%) tartrazine were extremely precise in size and adhered to the nominal value of the metformin hydrochloride content. Resolution analysis reinstated the influence of tartrazine in achieving highly precise objects of even 0.07 mm2 area. Furthermore, 3D printed ghost tablets were characterized using analytical means, and swelling studies. Additionally, ghost tablets were tested for their mechanical robustness using dynamic mechanical and texture analysis, and were able to withstand strains of up to 5.0% without structural failure. The printed ghost tablets displayed a fast metformin hydrochloride release profile, with 93.14% release after 12 h when the PEG 300 ratio was at its maximum. Ghost tablets were also subjected to in vivo X-ray imaging, and the tablets remained intact even after four hours of administration and were eventually excreted in an intact form through fecal excretion. [Display omitted] [ABSTRACT FROM AUTHOR]

Analytical sample preparation techniques are regarded as crucial steps for analyzing compounds from different biological matrices. The development of new extraction techniques is a modern trend in the bioanalytical sciences. 3D printed techniques have emerged as a valuable technology for prototyping devices in customized shapes for a cost-effective way to advance analytical sample preparation techniques. The present study aims to fabricate customized filaments through the hot-melt extrusion (HME) technique followed by fused deposition modeling mediated 3D printing process for rapid prototyping of 3D printed sorbents to extract a sample from human plasma. Thus, we fabricated our own indigenous filament using poly (vinyl alcohol), Eudragit® RSPO, and tri-ethyl citrate through HME to prototype the fabricated filament into a 3D printed sorbent for the extraction of small molecules. The 3D sorbent was applied to extract hydrocortisone from human plasma and analyzed using a validated LC-MS/MS method. The extraction procedure was optimized, and the parameters influencing the sorbent extraction were systematically investigated. The extraction recovery of hydrocortisone was found to be >82% at low, medium, and high quality control samples, with a relative standard deviation of <2%. The intra-and inter-day precisions for hydrocortisone ranged from 1.0% to 12% and 2.0%–10.0%, respectively, whereas the intra-and inter-day accuracy for hydrocortisone ranged from 93.0% to 111.0% and 92.0% to 110.0%, respectively. The newly customizable size and shape of the 3D printed sorbent opens new possibilities for extracting small molecules from human plasma. [Display omitted] • Developed indigenous filaments through hot-melt-extrusion technique followed by 3D printed sorbent. • 3D printed sorbents used for sample extraction of molecule. • The extraction recovery of hydrocortisone was found to be >82% with <2% relative standard deviation. [ABSTRACT FROM AUTHOR]