Search

Wood is a traditional roofing material in Europe and other parts of the world. In the seventeenth century, wooden roofing was generally used on more important buildings, but today it is mainly used on huts and houses in the Alpine regions. As wooden roofing is expensive, we investigated the possibility of extending the service life of the roofing through material selection and details. The roof of the Golobar cable yarding was covered with shingles made of spruce (Picea abies) and larch (Larix decidua). Part of the spruce roofing was thermally modified and/or treated with a water-wax emulsion. On the underside, we cut grooves in selected roof shingles to increase the specific surface of the wood and to accelerate drying after rainfall. In addition, wood moisture monitoring sensors were installed on the roof shingles. Based on three years of the wood moisture content measurements, it can be concluded that among shingles made of untreated spruce wood, the highest moisture content was recorded for shingles with a rectangular cross-section without additional grooves. The additional grooves positively affected the moisture performance of wood. Treating the wood with Silvacera wax had an even more pronounced effect on the moisture content of the shingles than the grooves. [ABSTRACT FROM AUTHOR]

This study aimed to evaluate the impact of thermal modification on the physical and mechanical properties of three different wood species from Bosnia and Herzegovina, namely beech wood (Fagus sylvatica L.), linden wood (Tilia cordata), and silver fir wood (Abies alba). The samples underwent thermal modification at five different temperatures (170 °C, 180 °C, 195 °C, 210 °C, and 220 °C) for varying durations (ranging from 78 to 276 min). After treatment, they were exposed to outdoor conditions for twelve months. The study examined the four-point bending strength, tensile force, color change, and surface quality of the modified and unmodified samples. The results showed that outdoor exposure negatively impacted the mechanical properties of the unmodified samples, especially in the linden wood which was 41% and the beech wood which was 42%. Additionally, outdoor exposure caused significant surface cracks in the thermally modified linden and beech wood. The study also found prominent color changes in the modified and unmodified samples during twelve months of exposure. The roughness of the samples was determined with a confocal laser scanning microscope, which showed that the roughness increased on both the axial and the longitudinal surfaces after weathering. The highest roughness for the fir wood was determined to be 15.6 µm. Overall, this study demonstrates the importance of wood modification and its impact on the use-value of wood products. [ABSTRACT FROM AUTHOR]

Thermal modification is the most important commercial modification procedure. Thermally modified (TM) wood has improved durability, but its performance does not meet expectations predominately under moist conditions. To reduce water uptake of TM wood, Norway spruce specimens were treated with suspensions of a natural wax by dipping impregnation (DipI) or by vacuum-pressure impregnation (VPI). Wax-treated specimens were subsequently TM at 185, 200, 215, and 230°C. Control specimens were heated up to 100°C only. Contact angle (CA), short-term and long-term water uptake, bending strength, and performance against wood decay fungi of the resulting material were determined. The results show that a combination of wax treatment and thermal modification have a synergistic effect that considerably improves hydrophobicity, reduces liquid water uptake, slows down water vapor uptake, and improves the resistance against fungal decay of the treated material. [ABSTRACT FROM AUTHOR]

This study aims to investigate the influence of thermal modification (TM) on the physical and mechanical properties of wood. For this purpose, the experimental part focused on selected influential parameters, namely temperature, residence time, and density, while the four-point bending strength is obtained as the output parameter. The obtained experimental data are stochastically modeled and compared with the model created by genetic programming (GP). The classical mathematical analysis obtained treatment parameters in relation to the maximum bending strength (T = 187 °C, t = 125 min ρ = 0.780 g/cm3) and compared with the results obtained by genetic algorithm (GA) (T = 208 °C, t = 122 min, and ρ = 0.728 g/cm3). It is possible to obtain models that describe experimental results well with stochastic modeling and evolutionary algorithms. [ABSTRACT FROM AUTHOR]

The importance of thermal modification is increasing worldwide. Increased use of thermally modified timber (TMT) has resulted in a need for reliable quality control, comprising control of variation of the production within defined limits, allowing third-party control in the case of certification and the regulation of customer complaints and claims. Techniques are thus needed to characterise the modification of quality in terms of improved target properties of TMT during industrial production, and of TMT products that have been in service for an arbitrary time. In this study, we aimed to utilise dynamic vapor sorption (DVS) for this purpose. Norway spruce (Picea abies) and European beech (Fagus sylvatica) samples were thermally modified at different temperatures according to different heat treatment techniques: (1) the Silvapro process based on an initial vacuum; (2) an air heat treatment, whereby samples were wrapped in aluminium foil; (3) thermal modification of wood samples in the ambient atmosphere in a laboratory oven. Wood samples from closed processes were analysed for validation. TMT was characterised with respect to mass loss, colour and density. Mass loss of wood due to modification (MLTM) was correlated with factors derived from DVS analysis. The present DVS measurements suggest that the equilibrium wood moisture content (EMC95% RH), the time to reach 10% wood moisture content (t10% MC), and the elongation factor, c, derived from a logarithmic function, can serve as alternative parameters to characterise the quality of several thermal modification processes. Further studies are recommended using other wood species, different modification processes and further parameters gained from DVS measurements to understand the robustness and the predictive power of the applied technique. [ABSTRACT FROM AUTHOR]

The development of non-biocidal and environmentally friendly systems to protect wood against biological decay has become a high priority in recent years. In the present study the impact of an innovative modification procedure, combining two environmentally friendly modification methods: thermal modification and mineralisation, using an aqueous solution of calcium acetoacetate as a precursor, on the fungal durability of wood was evaluated. European beechwood (Fagus sylvatica) and Norway sprucewood (Picea abies) were selected as model wood species. Wood samples were treated using either a single or combination of both methods and exposed to four different fungi: Gloeophyllum trabeum , Rhodonia placenta , Trametes versicolor and Pleurotus ostreatus. The effect of the different modifications on moisture content, dynamic vapour sorption, contact angle and pH value was also evaluated. Overall, the highest durability against Rhodonia placenta , Trametes versicolor and Pleurotus ostreatus was achieved through thermal modification in both wood species, while the combination of mineralisation and thermal modification has a synergistic effect against degradation by Gloeophyllum trabeum. In the case of beechwood the mass loss decreased from 41% for native to 6% for combined modified samples. We proved that the effectiveness of different treatment against fungal decay of wood were in strong dependence of their moisture content, dynamic vapour sorption, contact angle and pH values. The role of fungi on the morphology of the wood and on crystal structure of formed carbonate was investigated using SEM-EDS analysis. [Display omitted] • Presented ecological modification of wood can be an alternative to biocides. • A significant improvement in the fungal durability of wood was achieved. • Thermal modification and mineralisation work synergistic against wood decay fungi. • The reasons for a synergistic effect of combining methods were proposed. • The mass loss decreased from 41% for native to 6% for combined modified beechwood. [ABSTRACT FROM AUTHOR]

In this study, the combined effects of chemical (with tricine and bicine) and thermal treatments were investigated. The modifications which appeared in the wood structure were evaluated by infrared spectroscopy and chemometric methods (principal component analysis and hierarchical cluster analysis). After the treatment, about 6–7% of WPG was identified in treated samples, but further thermal treatment decreased the WPG to about 5%. The modifications appearing in the spectra were mostly related to increase of the intensities of the bands assigned to C O groups but also to N–H and C–N groups, with shifting of some bands to higher wavenumber values. Image 1 • The combined effects of chemical and thermal treatment on soft and hardwood were evaluated. • The effectiveness of treatment was evaluated by infrared spectroscopy and chemometric methods. • The occurrence of the reactions between the functional groups from bicine and tricine and wood structure were identified. • Softwood samples were more susceptible to chemical/thermal modification than the hardwood samples. [ABSTRACT FROM AUTHOR]

Results of the research aimed to increase the resistance of beech and thermally modified (TM) beech wood to UV-light and weathering with impregnation with commercially available nano TiO2 suspensions, originally intended to be used as UV protective coating additives, are presented in this paper. Beech wood and TM beech wood samples were vacuum-pressure impregnated with suspensions, containing around 3% of TiO2, and in one series, the specimens were at first impregnated and thermally modified afterwards. In general, resistance to UV-light, as demonstrated by visual observation and by colour measurements was increased. Contact angle of water, liquid water absorption, and water vapour sorption also importantly influence on weathering behaviour of wood and it was shown that in general, impregnation with TiO2 particles has a positive influence with this respect. Anyway, some results of this preliminary research were ambiguous, and subsequent investigations of this novel protection method are needed and planned. [ABSTRACT FROM AUTHOR]