Search

The diode bridge submodule (SM) is one of the basic units of a hybrid high-voltage dc circuit breaker. This article works on the low inductance design of a single SM and series SMs. For the layout design of a single SM, this article proposes a simple and clear +-shaped SM layout, the low inductance design is simplified to the optimization of two laminated busbars with a simple structure. Based on the +-shaped SM layout, this article further proposes an SM structure with holes in diodes region, the stray inductance is further reduced, and only one integrated laminated busbar is needed in a single SM. For the layout design of series SMs, this article makes full use of the layout of a single SM and the mutual inductances between the SMs, series SMs are alternately connected in reverse. The single SM layout proposed in this article is effective in reducing the stray inductance. The loop stray inductance in stage II reduced from 148.4 to 72.3 nH, a 51.3% reduction. When the two parallel IGBTs turn off a 6 kA fault current in 2 μs, the voltage spike is reduced from 786.1 to 423.4 V, a 46.1% reduction. And the stray inductance difference of the bidirectional current path is controlled to about 10 nH. The layout of series SMs proposed in this article is effective in reducing the length of the series SMs, the length is reduced by 16.7%. The experimental results show that the SMs layout proposed in this article is effective. [ABSTRACT FROM AUTHOR]

Hybrid circuit breaker (HCB) has shown good performance for interrupting dc fault current. However, a massive number of IGBTs in series is needed. These will lead to high costs and significant difficulty in balancing IGBT dynamic voltage. This paper proposes a bidirectional hybrid circuit breaker based on a cascaded half-bridge submodule structure to reduce the overall costs and implementation difficulty of HCB. The number of IGBTs is reduced by 50%, and the operating speed is fast enough. A model of a four-terminal modular multilevel converter (MMC) system with a proposed hybrid circuit breaker in different stages is developed to describe the fault blocking process more clearly. The performance of the proposed HCB is validated and compared with other HCB structure through both theoretical derivation and time-domain simulation. [ABSTRACT FROM AUTHOR]

A mechanical switch can be used instead of a power electronic load commutation switch in orderto reduce the losses during normal power flow in standard hybrid DC circuit breakers. The success of current commutation in such hybrid breakers depends on the arc voltage formed across the contacts in the mechanical switch. The behaviour of rapidly elongated, wall constricted arcsgenerated during the opening of an ultra-fast mechanical switch in the air is studied here. The voltage-current characteristics of the generated arcs are obtained for steady state contact opening velocities of 6, 11 and 21 m/s. It is found that the arc voltage at a given current and contact separation increases with the contact opening velocity. It is shown that stationary,zero-contact-velocity characteristics can not be used to accurately quantify the voltage build-up in fast elongating arcs in hybrid breakers. A best-fitting black-box equation for the dynamic arc characteristics is presented for the tested velocities. The obtained voltage-current characteristics are used as input to simulate the current commutation process in a 12 kV hybridDC circuit breaker case-study. Different scenarios of current commutation failure related to the arc voltage build up are identified. It is shown that these failures scenarios can be avoided by increasing the contact opening velocity. [ABSTRACT FROM AUTHOR]

In recent years, dc distribution grids have become increasingly popular because of the interest in the diffusion of distributed renewable energy. In this scenario, dc distribution grids are also favored because of the increased use of batteries and power electronic loads. The main limit to the spread of dc grids is their protection devices, which still present several problems. At present, protection devices are represented by traditional mechanical breakers or static electronic components. The first, which interrupt dc currents, have good reliability but need maintenance and have long intervention periods. In contrast, electronic switches are fast and reliable, but they reduce the efficiency because of their voltage drop. In this scenario, some hybrid breakers have been proposed to obtain the advantages of both devices. The previous solutions of hybrid breakers still suffer several critical issues and, usually, are not capable of protecting a system from short circuits without significantly reducing their lifetime. In this paper, a new low-voltage hybrid circuit breaker topology is proposed. The procedure to dimension all of the active and passive components in the device is analyzed, and the effectiveness of the proposed solution is proven by means of experimental results obtained using a prototype. [ABSTRACT FROM AUTHOR]