Search

We demonstrate the use of patterned aerosol adhesives to construct both planar and nonplanar 3D paper microfluidic devices. By spraying an aerosol adhesive through a metal stencil, the overall amount of adhesive used in assembling paper microfluidic devices can be significantly reduced. We show on a simple 4-layer planar paper microfluidic device that the optimal adhesive application technique and device construction style depends heavily on desired performance characteristics. By moderately increasing the overall area of a device, it is possible to dramatically decrease the wicking time and increase device success rates while also reducing the amount of adhesive required to keep the device together. Such adhesive application also causes the adhesive to form semi-permanent bonds instead of permanent bonds between paper layers, enabling single-use devices to be non-destructively disassembled after use. Nonplanar 3D origami devices also benefit from the semi-permanent bonds during folding, as it reduces the likelihood that unrelated faces may accidently stick together. Like planar devices, nonplanar structures see reduced wicking times with patterned adhesive application vs uniformly applied adhesive.

This article discusses the fabrication of planar and nonplanar 3D paper microfluidic circuits through the use of patterned spray adhesive application and origami techniques. The individual paper layers are held together via semi-permanent adhesive bonds without the need for external clamps. Semi-permanent bonds accommodate the repeated folding and unfolding required by complex origami device structures and allow the device to be unfolded post-use to view internally displayed results. Combinations of adhesive patterns and fluid channel widths were identified that did not prevent the fluid from traveling between layers and through the entire circuit. Further, this method was extended to nonplanar 3D paper microfluidic circuits, demonstrated via multi-fluid wicking within a modified origami peacock. Such nonplanar 3D paper microfluidic circuits are expected to offer an entirely new platform for exploring new designs and functions of paper analytical devices.

Starch paste is an adhesive that is used in the field of book and paper conservation. This adhesive has a very short shelf life, and for this reason, it must be prepared in small quantities. Also, preparing starch paste for use in protection is a time-consuming process. This research was done with the aim of facilitating the use of starch paste in the conservation of paper works, long-term storage of starch pastes without fungicidal additives and increasing its durability in the long term without changing the quality of the adhesive. The application of fresh starch pastes and activated starch film increased the pH of the samples coated by these adhesives compared to the control samples without adhesive. The samples covered by the activated starch film after moist-heat aging and light aging had the highest pH compared to other samples. The samples coated with fresh starch paste showed the lowest amount of color changes (ΔE*) after moist-heat aging and light aging, respectively. Application of fresh starch paste and activated starch film increased the tensile strength of the samples. After aging, the tensile strength of the samples decreased compared to the previous stage, but the tensile strength of the samples covered by these adhesives increased compared to the control samples without adhesives. The adhesion of the samples decreased after aging. The samples coated with fresh starch paste had the highest adhesion after light aging. Also, after moist-heat aging, the samples covered by the activated starch film had the highest amount of adhesion. [ABSTRACT FROM AUTHOR]

This research explores the practical advantages and potential applications of spray adhesives, focusing on testing their suitability for artwork mounting uses. Their solubility in common low-toxicity solvents (ethanol and acetone) was evaluated. Seven commercial spray adhesives from different commercial brands and compositions were applied on paper samples and subjected to different ageing conditions. The samples were then immersed in the solvent, and the degree of adhesive removal was measured. One of the most relevant conclusions is that commercial neoprene-based spray adhesives become brittle and fragile in a few weeks, which makes them unsuitable for both long-term and temporary applications in the heritage field. On the other hand, the solubility was high or very high in some cases: up to 98 % of adhesive removal was achieved in acetone wash. These tests and the convenience, cost and availability of spray adhesives suggest that some of them may be safely used in some scenarios such as temporary mountings or transport. [ABSTRACT FROM AUTHOR]

Formaldehyde-free adhesives are gaining attention due to their compatibility with green production methods. Decorative base paper (DBP) is known for its physical strength and printability and has a high ability for absorbing aldehyde-free adhesives for impregnation. In this paper, DBP was prepared with TiO2 and SiO2 combined with polyvinyl alcohol (PVA), where the amount of TiO2 was reduced in the pulp process. The prepared DBP was impregnated by aldehyde-free adhesive and hot-pressed on wood-based panels. The results showed that upon SiO2 coating, the surface smoothness of base paper increased by 132.3 %, whereas the tensile strength increased by 33.6 %. Furthermore, the colour density of cyan, magenta, yellow and black colours increased by 75.4 %, 99.2 %, 51.9 % and 90.5 %, respectively. The surface properties like surface bonding strength and wear resistance of the covered wood-based panels were found to satisfy the standard requirements, which indicates the products can be used for furniture products. [ABSTRACT FROM AUTHOR]

In addition to satisfying a book binding criterion, the paperback should provide content moments. Its binding style must be adjusted to book purpose. In publishing longruns production, the perfect (adhesive) binding style with flexible hotmelt provides optimal binding durability with reasonable book price. Paperback should appeal to everyone through its visual-tactile senses. Taking the required actions in binding quality realization keeps track of comprehensive knowledge on various standardized paper substates (EN643:G3) that need to be wisely joined to realize perfect binding technique practices effectively. Moreover, designer technological awareness gained by experience provides potentials to understanding binding ability principles. The conducted research gives specific answers regarding paper cohesive capacity impact on consistency changes of adhesive bound book. It was concluded that higher paper drape capacity leads to increase of single sheet paper tension. Inappropriate bound book constructing was achieved although the flexible adhesive was used. [ABSTRACT FROM AUTHOR]

Background: Protein contact dermatitis is better known in food-service and health-care workers than in industrial workers. Cornstarch has seldom been a problem, although it can cause contact urticaria to glove powder., Objective: To present the case of a paper-bag maker who developed severe occupational (protein) contact dermatitis within two-three hours after returning to work. She lacked any evidence of urticaria and demonstrated largely negative patch-test results., Methods: Following a history of occupational exposure to a cornstarch-based adhesive, the patient was patch-tested to materials with which she had worked, which she contacted, and with which she had attempted treatment. Following patch testing, she was prick-tested to cornstarch, the principal ingredient in the adhesive., Results: Patch testing was negative except for a very mild reaction to the adhesive. Prick testing to cornstarch was more severe than the histamine control. The test site became eczematous and remained so for more than ten weeks. Avoidance of cornstarch and the adhesive was followed by clearing., Conclusion: Workup for prominent occupational contact dermatitis without urticaria may sometimes require testing for type 1 allergy.

An extensive network of gummed paper collectors was used during the 1950s for routine monitoring of radioactive fallout from weapons testing. The experiments reported in this paper were designed to examine the collection efficiency of gummed paper for wet deposition of several types of soluble and insoluble radioactive contaminants under conditions similar to those found during natural rainstorms. The collection efficiencies for each substance were determined over a range of rainfall amounts and at two separate rainfall intensities. The collection efficiency of the gummed paper is highest for large insoluble particles and lowest for soluble ionic substances. The values for 7Be and 131I ranged from about 0.30 (30%) at 2.5 mm of rain to 0.04-0.06 (4%-6%) at 20 mm of rain. These values were negatively correlated with the amount of rain and were unaffected by rain intensity. This suggests that the collection efficiency of either ion is simply a matter of rapid saturation and runoff. Neither rain amount nor rain intensity has much effect on the collection efficiency of large insoluble particles. These particles seem to settle readily onto the surface of the gummed paper from which they are not easily removed by additional rain. Analysis of the collection efficiencies of the gummed paper included the activity of both the gummed paper and the standing water on the paper. A large portion of the activity for the ionic substances was found in the standing water. There was less activity by insoluble particles in standing water. This indicates that for estimates of deposition of soluble substances, considerable bias could be introduced into the results if the standing water is discarded prior to analysis.

The paper summarizes data on laboratory and clinical assessment of Corega denture adhesive cream adhesive properties: adhesion strength and time of adhesive material fixing. Clinical assessment was based on Ulitovsky-Leontyev denture fixation index evaluated in 18 edentulous patients with full removable dentures 1 and 12 months after denture manufacturing. After one year of evaluation denture fixation in patients using Corega denture adhesive cream was 8-15% better (depending on alveolar bed anatomy) than in controls proving that Corega improves full denture adaptation to physiological atrophy of alveolar bone.

This study sought to investigate the significance of raw materials (starch-based glues, raw material papers) at different microbiologically critical stages in the manufacturing process of refined paper products. The study examined the occurrence of microorganisms in the process and in end-product samples. Microbiological surveys verified that the production and use of pasteurized starch-based glue was the most important factor threatening the process hygiene and product safety. Subsequently, the production and use of starch-based glue was changed, and a follow-up programme targeting the microbiological quality of glue was developed as part of a hygiene and safety management system. A total of 33 spore-forming bacterial and 15 enterobacterial isolates were ribotyped, and 22 and 10 different ribogroups (ribotypes), respectively, were generated. These isolates from starch-based glue, raw material paper and end products were atypical and, thus, in many cases physiological, chemotaxonomic (FAME) and molecular (partial 16S rDNA) results did not correspond. The most common spore-forming bacteria (55% of the isolates) were Paenibacillus sp. and within this genus several new species were also proposed. The most common enterobacteria (87%) were Enterobacter cloacae and Citrobacter freundii belonging to bacteria in hazard group 2, or species closely related to them. It was demonstrated that the same spore-forming bacteria (ribotypes) were present in both the glue samples and the end products (45% of isolates). All RiboPrint patterns were saved at the VTT identification library for future use.

The rise of fentanyl and fentanyl analogs in the drug supply pose serious threats to public health. Much of these compounds enter the United States through shipping routes. Here we provide a method for fentanyl screening and analysis that utilizes pressure‐sensitive adhesive (PSA) lined paper to recover drug residues from parcel‐related surfaces. The paper used is commercially available repositionable notes (also called post‐it or sticky notes). From this paper, mass spectra were obtained by paper spray‐mass spectrometry (PS‐MS), where PSA paper served as both a sampling and analysis substrate. Seven fentanyl‐related compounds were analyzed: fentanyl, 4‐anilino‐N‐phenethylpiperidine (4‐ANPP), N,1‐diphenethyl‐N‐phenylpiperidin‐4‐amine (phenethyl‐4‐ANPP), valerylfentanyl, 4‐fluoroisobutyrylfentanyl (4‐FIBF), carfentanil, and p‐fluorofentanyl. These compounds were recovered by PSA paper and identified by PS‐MS from packaging tape and plastic at 50 ng and from cardboard and shipping labels at 100 ng. The impact of cutting agents on PS‐MS analysis of fentanyl analogs was explored. No trends of analyte suppression were found at high concentrations of the cutting agents caffeine, diphenhydramine, and lidocaine when recovered from surfaces. A cartridge that required no precise cutting of PSA paper prior to sampling or analysis was evaluated for use in PS‐MS for fentanyl screening. Recovery and detection of fentanyl from plastic sheeting was demonstrated with this cut‐free cartridge. The cut‐free cartridge showed somewhat less consistency and lower analyte signal than the standard cartridge, but performance was suitable for potential screening applications. In combining PSA surface sampling with PS‐MS for drug screening, both sampling and detection of fentanyl‐related compounds is simple, rapid, and low‐cost. [ABSTRACT FROM AUTHOR]