Search

The filter paper (FP) method, a cost-effective, versatile, and convenient approach, has found extensive application in analyzing fine-grained soils, enabling the successful measurement of a broad spectrum of total and matric suctions. However, using the FP method in sand with a limited range of suction profiles has been notably underrepresented in the existing literature. Therefore, this study investigated the applicability of the contact FP method in establishing soil water retention curves (SWRCs) using five distinct FP calibration curves for 10 poorly graded sands. Among these calibration curves, the one presented by Chandler yielded the highest suction values, which were followed by those of ASTM. Furthermore, the FP results were subjected to fitting with a mathmatical model, which led to the observation that the overall trends in the obtained SWRCs displayed smooth sigmoidal shapes, resulting in a complete and coherent SWRCs. The SWRC results of five sand samples were assessed through validation against the hanging column technique (HCT) results, indicating a high degree of concordance and affirming the suitability of the FP method for sands characterized by a limited suction profile. Notably, the entire range of suction values fell within the 0.01–20 kPa range based on the calibration curves presented by Chandler and ASTM for all the examined sand samples, except sands 9 and 10. Furthermore, the suction values were unobtainable using the two aforementioned calibration curves within the ranges of 0.01–1.47 kPa and 0.01–0.172 kPa. [ABSTRACT FROM AUTHOR]

Polyethylene-, polyvinylidene chloride-, and per- and polyfluoroalkyl substance-coated paper generate microplastics or fluorochemicals in the environment. Here, we report an approach for the development of oil-resistant papers using an environmentally friendly, fluorine-free, water-dispersible poly(dimethylsiloxane) (PDMS) coating on kraft paper. Carboxylic-functionalized PDMS (PDMS-COOH) was synthesized and subsequently neutralized with ammonium bicarbonate to obtain a waterborne emulsion, which was then coated onto kraft paper. The water resistance of the coated paper was determined via Cobb60 measurements. The Cobb60 value was reduced to 2.70 ± 0.14 g/m2 as compared to 87.6 ± 5.1 g/m2 for uncoated paper, suggesting a remarkable improvement in water resistance. Similarly, oil resistance was found to be 12/12 on the kit test scale versus 0/12 for uncoated paper. In addition, the coated paper retained 70–90% of its inherent mechanical properties, and more importantly, the coated paper was recycled via pulp recovery using a standard protocol with a 91.1% yield. [ABSTRACT FROM AUTHOR]

As air pollution escalates, the need for air filters increases. It is better that the filters used be based on natural fibers, such as non-wood fibers, which cause low damage to the environment. However, the short fiber lengths, low apparent densities, and high volumes of non-wood materials can make it challenging to prepare filter paper with the required mechanical and physical properties. In that context, this study focused on utilizing bamboo fibers to fabricate filter paper by employing the anthraquinone soda pulping method. The pulp underwent bleaching and oxidation processes, with the incorporation of cationic starch (CS) and polyvinyl alcohol (PVA) to enhance resistance properties, resulting in the creation of handmade filter papers. The findings revealed that the tear, burst, and tensile strength of filter paper increased with the oxidation and addition of CS and PVA. Air permeability increased with addition of PVA and combination of CS and PVA. FTIR demonstrated the conversion of hydroxyl groups in cellulose chains to carboxyl groups due to oxidation. SEM images illustrated alterations in the fiber structure post-oxidation treatment, with CS reducing pores while PVA and the CS-PVA combination enlarged pore size and enhanced porosity. The BET surface area surface area expanded with oxidation and the addition of the CS-PVA blend, indicating heightened filter paper porosity. Notably, the combined inclusion of CS and PVA not only augmented mechanical strength but also increased porosity while maintaining pore size. [ABSTRACT FROM AUTHOR]

Objectives: Endoscopic ultrasound‐guided tissue acquisition (EUS‐TA) is used for pathological diagnosis and obtaining samples for molecular testing, facilitating the initiation of targeted therapies in patients with pancreatic cancer. However, samples obtained via EUS‐TA are often insufficient, requiring more efforts to improve sampling adequacy for molecular testing. Therefore, this study investigated the use of oil blotting paper for formalin fixation of samples obtained via EUS‐TA. Methods: This prospective study enrolled 42 patients who underwent EUS‐TA for pancreatic cancer between September 2020 and February 2022 at the Osaka International Cancer Institute. After a portion of each sample obtained via EUS‐TA was separated for routine histological evaluation, the residual samples were divided into filter paper and oil blotting paper groups for analysis. Accordingly, filter paper and oil blotting paper were used for the formalin fixation process. The total tissue, nuclear, and cytoplasm areas of each sample were quantitatively evaluated using virtual slides, and the specimen volume and histological diagnosis of each sample were evaluated by an expert pathologist. Results: All cases were cytologically diagnosed as adenocarcinoma. The area ratios of the total tissue, nuclear, and cytoplasmic portions were significantly larger in the oil blotting paper group than in the filter paper group. The frequency of cases with large amount of tumor cells was significantly higher in the oil blotting paper group (33.3%) than in the filter paper group (11.9%) (p = 0.035). Conclusions: Oil blotting paper can increase the sample volume obtained via EUS‐TA on glass slides and improve sampling adequacy for molecular testing. [ABSTRACT FROM AUTHOR]

The lifespan of an electrical transformer, primarily determined by the condition of its solid insulation, is well known under various operating conditions when mineral oil is the coolant in these machines. However, there is a trend toward replacing this oil with biodegradable fluids, especially esters; therefore, an understanding of the ageing of solid insulation with these fluids is essential. Currently available data do not allow for the selection of the best ester among those available on the market, as each study applies different conditions, making it impossible to compare results. Thus, this paper analyses the degradation of Kraft and Thermally Upgraded Kraft papers with the following five most promising commercial esters: sunflower, rapeseed, soybean, palm, and synthetic. The materials underwent accelerated thermal ageing at 130, 150, and 170 °C, and the integrity of the papers was evaluated through their polymerisation degree and the obtaining of the degradation kinetic models. The wide range of materials studied in this work, which were subjected to the same treatments, allows for a comparison of the esters, revealing significant differences in the impact of the alternative fluids. Sunflower, rapeseed, and soybean esters provided the best paper protection, i.e., the degree of polymerisation of Kraft paper in the tests at 150 °C decreased by 71% with these fluids, compared to the 83% reduction with mineral oil, 79% reduction with palm ester, and 75% reduction with synthetic ester. Furthermore, different kinetic models were obtained to predict the degradation; it was concluded that the Emsley model provides the best fit. Additionally, it was found that the behaviour of a dielectric fluid with one type of paper cannot be extrapolated, which is only noticeable in broad-scope studies. [ABSTRACT FROM AUTHOR]

The increase in energy valorization of paper sludge and biomass waste through incineration results in a rise in waste paper fly ash (WPFA), often perceived as hazardous and requiring specific treatment. In this study, natural carbonation technology at a pilot scale was employed to mitigate the hazardous nature of WPFA by enhancing the stabilization of metal and metalloid trace elements (MMTE), particularly barium (Ba) and lead (Pb) leaching. Natural carbonation of WPFA was found to be optimal at a water/solid ratio of 0.3 L/kg under natural temperature and humidity conditions. Batch leaching tests based on thermodynamic equilibrium were used to assess MMTE solubility concerning pH in both non-carbonated and carbonated WPFA at natural pH. After 7 days of natural carbonation, the leaching concentration of Ba and Pb was below the legal limit in France. The concentration of Ba and Pb in carbonated samples decreased by 98.5% and 98%, respectively. Analyses using thermogravimetry, X-ray diffraction, scanning electron microscopy, and energy-dispersive spectroscopy demonstrated the increased formation and quantity of calcite (CaCO3) with longer carbonation times, along with the formation of new minerals as BaCO3 and PbCO3, confirming the immobilization of these elements post-carbonation. The leaching behavior and release potential of carbonated WPFA were further evaluated using the four-stage sequential extraction procedure proposed by the European Commission's Bureau of Reference (BCR). The speciation of Ba and Pb shifted significantly from the soluble substance (F1) at 17.6% and 14.8%, respectively, to the carbonate fraction (F2) at 0.49% and 0.02% after 90 days of carbonation. The percolation water collected during the carbonation process adheres to discharge standards into the sea. [ABSTRACT FROM AUTHOR]

In the field of book heritage, it is important to develop cleaning/disinfecting treatments that can slow down the degradation of paper to prevent evident and irreversible damage. The objectives of the cleaning treatments are to remove external contaminants and oxidation and decomposition products of the paper, but these processes must not modify the unique characteristics of the book heritage resulting in irreversible changes in the structure of the paper. Recently, several innovative cleaning treatments were developed with the aim of being minimally invasive; however, to assess the effect of these treatments on paper, it is necessary to use a diagnostic non-destructive, rapid, and affordable process. In previous work, we used surface scanning Raman spectroscopy to develop a diagnostic protocol able to follow the aging processes of the paper, discriminating between hydrolysis and oxidation. In this paper, we applied this protocol to study the action of different types of treatments (hydrogel and EUV irradiation), evaluating both their effectiveness and impact on paper parameters. The results reported here demonstrate that the developed in operando diagnostic procedure can follow the changes in the paper structure comparing them to the variability due to the intrinsic inhomogeneity of paper, without sample contact in a rapid and effective way. [ABSTRACT FROM AUTHOR]

Developing cost-effective and stable materials for the electrocatalysis of hydrogen evolution reaction (HER) remains challenging. In this study, efficient catalysts for HER were synthesized by integrating the cobalt and molybdenum oxides via electrodeposition, followed by subsequent sulfurization of the as-prepared oxides using chemical vapor deposition (CVD). This methodology allowed the incorporation of both cobalt and molybdenum components into the catalyst in a single step. The as-synthesized CoSx@MoSx/MoOx-based catalysts exhibited excellent hydrogen production performance in acidic media owing to the presence of Co-S and Mo-S bonds in the hybrid structure. Particularly, CoSx@MoSx/MoOx(90@360) and MoSx@CoOx(180@180) displayed the best HER performances with low overpotentials of 80 mV and 150 mV, respectively. The catalysts were highly stable, with their stability preserved for over 1000 cycles with marginal reduction in overall efficiency. Therefore, these findings suggest the potential of CoSx@MoSx/MoOx and MoSx@CoOx composites as ideal candidates for developing low-cost catalysts for electrochemical hydrogen production. [ABSTRACT FROM AUTHOR]

Carbon paper is one of the most widely used gas diffusion layer substrate materials due to its stable performance, relatively low cost, and easy for subsequent processing. Water-soluble phenolic resin, which is more ecologically friendly than alcohol-soluble phenolic resin, was used to prepare carbon paper as the precursor of the carbon matrix. And the effect of different resin solution concentrations on the properties of carbon paper was explored. The results showed that the graphitization, electrical conductivity and mechanical properties of carbon paper increased with the increase of resin solution concentration. When the concentration of resin solution was 20 wt%, the performance of carbon paper was relatively optimal. The graphitization of the carbon paper reached 65.45%, the porosity reached 80.74%, the resistance value at 1 MPa pressure was only 7.61 mΩ cm2, the tensile strength was 1.57 MPa, and the elastic modulus was 1210.98 MPa. [ABSTRACT FROM AUTHOR]

Buckypaper (BP), a flexible and porous material, exhibits photovoltaic properties when exposed to light. In this study, we employed radio frequency (RF) sputtering of zinc oxide (ZnO) followed by rapid thermal annealing to enhance the photovoltaic response of BP. We investigated the impact of various sputtering parameters, such as the gas flow ratio of argon to oxygen and deposition time, on the morphology, composition, resistivity, and photovoltaic characteristics of ZnO-modified BP. Additionally, the photovoltaic performance of the samples under different illumination modes and wavelengths was compared. It was found that optimal sputtering conditions—argon to oxygen flow ratio of 1:2, deposition time of 20 min, and power of 100 watts—resulted in a ZnO film thickness of approximately 45 nanometers. After annealing at 400 °C for 10 min, the ZnO-modified BP demonstrated a significant increase in photocurrent and photovoltage, along with a reduction in resistivity, compared to unmodified BP. Moreover, under gradient illumination, the ZnO-modified BP exhibited a photovoltage enhancement of 14.70-fold and a photocurrent increase of 13.86-fold, compared to uniform illumination. Under blue light, it showed a higher photovoltaic response than under other colors. The enhancement in photovoltaic response is attributed to the formation of a Schottky junction between ZnO and BP, an increased carrier concentration gradient, and an expanded light absorption spectrum. Our results validate that ZnO sputtering followed by annealing is an effective method for modifying BP for photovoltaic applications such as solar cells and photodetectors. [ABSTRACT FROM AUTHOR]

Size presses on paper machines are used to apply a solution of a polymer - usually starch - to the surface of the sheet and thereby to increase the stiffness, surface strength, and printing quality of the product. This article reviews publications dealing with the size press equipment, the materials, and factors affecting both the operating efficiency and attributes of the resulting paper. The emergence of film-press equipment (e.g. blademetering size presses) in the 1980s has greatly decreased the frequency of web breaks and increased productivity. Starch technology at the size press, though relatively mature, continues to evolve. By adjustment of starch attributes, solids levels, and incorporating other additives, modern papermakers can tune size press outcomes to meet a range of paper product requirements, including strength, hydrophobicity, and the reduction of air permeability. By application of various synthetic polymers, mineral particles, and even nanocellulose in combination with starch or other base polymers, there is potential to extend the technology to meet a range of future needs for paper products. [ABSTRACT FROM AUTHOR]

The main part of companies in Bulgaria are built, however in the 70s, and upgraded last decade. The country supplies around 80 % of its supplies of paper, paperboard and pulp with own production. Integrated treatment of wastes is a priority for realizing closed life cycle of materials. The aim of the present work is to investigate the composition and other important characteristics of biomass wood ash wasted from paper industry. The correlations and associations among the chemical characteristics are also studied to find some basic trends and important relationships between two similar wastes from different enterprises. It was proved that all samples taken contained Ba, Cr, Mn, Ni, Co, Al, Fe, Cu and Zn far below the legal limits for such type of products. A product has a certain anti-acidic effect. The other positive result was that the content of iron is between 34 to 60 mg per 1 kg dry waste. The microscopic photos confirmed that the particles are close to the nano-size materials. The content of the elements C, N, H is in good quantities and ratios, which is a prerequisite for their use as a soil improver. By the results of this study, it was confirmed that all samples produced as a result of the thermal treatment and final low water content achieved are free from pathogen microorganisms and different weed seeds, affecting the yield and soil sustainability. That allows determining the optimal ratio between the used components with a view to obtain products with desired thermal stability and physico-chemical properties as soil improvers. [ABSTRACT FROM AUTHOR]

The pulp and paper industry is critical to global industrial and economic development. Recently, India's pulp and paper industries have been facing severe competitive challenges. The challenges have impaired the environmental performance and resulted in the closure of several operations. Assessment and prediction of the performance of the Indian pulp and paper industry using various parameters is a critical task for researchers. This study proposes a framework for performance assessment and prediction based on Data Envelopment Analysis (DEA), Artificial Neural Networks, and Deep Learning (DL) to assist industry administration and decision-making. We presented a case study based on eight industries to demonstrate the methodology's applicability. This study analyses and predicts industry performance based on sample data observations over 30 years. The result suggests the DEA-DL-based efficiency prediction has an overall MSE of 0.08 compared with the actual efficiency. Furthermore, the efficiency rankings are compared between the three techniques. The results suggest that the integrated DEA-DL method is primarily accurate in most scenarios with the actual values. The findings of this study provide a comprehensive analysis of environmental performance for policymakers. [ABSTRACT FROM AUTHOR]

Achieving the desired properties of paper such as strength, durability, and printability remains challenging. Paper mills employ calcium carbonate (CaCO3) as a filler to boost paper's brightness, opacity, and printability. However, weak interaction between cellulose fibers and CaCO3 particles creates different issues in the papermaking industry. Therefore, this study explores the influence of various inorganic additives as crosslinkers such as mesoporous SiO2 nanospheres, TiO2 nanoparticles, h-BN nanoflakes, and hydroxylated h-BN nanoflakes (h-BN-OH) on inorganic fillers content in the paper. They were introduced to the paper pulp in the form of a polyethylene glycol (PEG) suspension to enable bonding between the inorganic particles and the paper pulp. Our findings have been revealed based on detailed microscopic and structural analyses, e.g., transmission and scanning electron microscopy, X-ray diffraction, Raman spectroscopy, and N2 adsorption/desorption isotherms. Finally, the inorganic fillers (CaCO3 and respective inorganic additives) content was evaluated following ISO 1762:2001 guidelines. Conducted evaluations allowed us to identify the most efficient crosslinker (SiO2 nanoparticles) in terms of inorganic filler retention. Paper sheets modified with SiO2 enhance the retention of the fillers by ~12.1%. Therefore, we believe these findings offer valuable insights for enhancing the papermaking process toward boosting the quality of the resulting paper. [ABSTRACT FROM AUTHOR]

Aims: Information on breastfeeding and safety of biologics in infants is lacking due to difficulties in case collection. We evaluated methods for determining the concentration of biologics in breast milk using a dry filter method that can simplify the collection, storage and transport of breast milk. Methods: To generate dried filter paper (DFP) samples, approximately 30 μL of breast milk was placed onto a Whatman 903 card and punched out. After extraction, the supernatant was measured using an enzyme‐linked immunosorbent assay. Three concentrations of each drug were prepared in liquid breast milk (LBM) and DFP samples to determine their stability up to 28 days after storage at 2–8°C or −20°C for LBM and 25 ± 5°C for DFP. LBM and DFP samples were also provided by nursing mothers using biologics during lactation, and drug concentrations in both samples were compared. The agreement between the two measurement methods was confirmed by Bland–Altman analysis. Results: Breast milk was provided by 12 mothers who used biologics (tocilizumab, abatacept, etanercept, golimumab, sarilumab and belimumab). The coefficients of variation for within‐run and between‐run precision for the six drugs were within 15% for both LBM and DFP, and accuracy was within 90%–110% of the quality controls. After 28 days, concentrations remained at more than 90%. The difference between the values obtained by each method was within the acceptable range of error (−12.1 to +16.6 ng/mL). Conclusions: A method for determining the concentration of biologics using DFP is expected to help improve pharmacotherapy for lactating women. [ABSTRACT FROM AUTHOR]

Highly cited papers showcase high-quality research and encompass significant themes in the field. This study examined a total of 435 highly cited papers based on Essential Citation Indicators in the Web of Science (WoS) category of sport sciences with a bibliometric method. In particular, the bibliometric indicators of the highly cited papers including publication venues, authors, countries, institutions, and the top cited publications were presented and analyzed in detail. An Abstract corpus was constructed to help identify the most frequently explored topics. VOSviewer was employed to visualize the co-occurrence networks of keywords. The study revealed the trending information of important contributors at the levels of journals, authors, countries, and institutes. The top cited publications can be grouped into three categories: guidelines, recommendations based on systematic reviews, and evaluations. The most frequently explored topics based on the Abstract corpus and the most frequently used keywords from VOSviewer mapping overlap to a great extent. Specifically, topics such as meta-analysis, systematic review, sport-related concussion, sedentary behavior, football, rehabilitation, and osteoarthritis are among the most frequently mentioned. The results provide the most updated publication characteristics and hot topics of highly cited papers in sport sciences and offer insights for academic researchers in future research. [ABSTRACT FROM AUTHOR]

Poly(3-hydroxybutyrate) (PHB), a biodegradable polymer, has been studied as a substitute for petroleum-based polymers used for barrier coating to improve the barrier and mechanical properties of paper. In this study, ethyl cellulose (EC), a cellulose derivative, was used to prepare a polymer blend for enhancing the barrier properties of PHB. The prepared PHB/EC blend was then applied as a paper coating material. Additionally, the barrier and mechanical properties of the PHB/EC blend-coated paper based on the PHB/EC mixing ratio and coating weight were analyzed. The results showed that the EC could act as a binder for the PHB/EC blendcoated paper. Consequently, the PHB/EC blend-coated paper exhibited significant improvements in mechanical and barrier properties, including a substantial increase of over 100% in internal bond strength, more than 20% in tensile strength, exceeding 60% enhancement in water resistance, and a remarkable increase of over 90% in air permeability. [ABSTRACT FROM AUTHOR]

This study evaluated the production of marine biodegradable plastics, specifically polyhydroxyalkanoates (PHAs), using waste paper from food containers as a novel material source. The results showed that adding dilute sulfuric acid as a pretreatment may have a negative impact on enzyme hydrolysis efficiency. Without pretreatment, the highest glucose concentration was observed in the 50-min heating group. In the experimental group with 1% dilute sulfuric acid as a pretreatment, the highest average glucose concentration was observed in the 25-min treatment group. In flask scale experiments, the C/N ratio was controlled at 10, 20, and 30. The results showed that when the C/N ratio was 10, the PHA/CDM ratios were 16.3 and 23.6 at 48 and 72 h, respectively. After 96 h of cultivation using hydrolysis liquid from the waste paper container as the sole carbon source in a 5-L scale experiment, the PHA/CDM ratio was 28.7 and the PHA concentration was 0.95 g/L. The potential bacterial strain in this study was confirmed to be a Bacillus genus bacterium after strain identification. The signal peaks indicated that the PHA obtained from the Bacillus sp. production process was PHB. [ABSTRACT FROM AUTHOR]

Nowadays, the emphasis is on increasing the durability of all products. For this reason, it is also advisable to look into extending the durability of paper products. The main reason for using flax pulp is that flax and cotton pulp are widely used for the production of banknotes due to their higher strength. This paper deals with flax pulp with the addition of nanocellulose, which should further enhance the mechanical properties of the pulp. The tensile strength, breaking length, and tensile energy absorption index were evaluated as the key mechanical properties. At the same time, the effect of the addition of nanocellulose, whether it was added to the pulp mass or applied to the later produced paper as a spray or coating, was tested in comparison to paper without the addition of nanocellulose. The best mechanical properties, i.e., tensile strength, were achieved for the highest addition of 5% of nanocellulose into the pulp, at 24.3 Nm∙g−1, and for the coating application, at 28.7 Nm∙g−1, compared to the flax pulp without the addition, where the tensile strength was 20.5 Nm∙g−1. The results of this research are used for the assessment of nanocellulose as a natural compatible additive to enhance the strength properties of cellulose-based materials. [ABSTRACT FROM AUTHOR]

Though paper is an environmentally friendly alternative to plastic as a packaging material, it lacks antibacterial properties, and some papers have a low resistance to oil or water. In this study, a multifunctional paper-coating material was developed to reduce the use of plastic packaging and enhance paper performance. Natural cellulose nanocrystals (CNCs) with excellent properties were used as the base material for the coating. The CNCs were functionalized into dialdehyde CNCs (DACNCs) through periodate oxidation. The DACNCs were subsequently complexed using erythrosine as a photosensitizer to form an erythrosine–CNC composite (Ery-DACNCs) with photodynamic inactivation. The Ery-DACNCs achieved inactivations above 90% after 30 min of green light irradiation and above 85% after 60 min of white light irradiation (to simulate real-world lighting conditions), indicating photodynamic inactivation effects. The optimal parameters for a layer-by-layer dip coating of kraft paper with Ery-DACNCs were 4.5-wt% Ery-DACNCs and 15 coating layers. Compared to non-coated kraft paper and polyethylene-coated paper, the Ery-DACNC-coated paper exhibited enhanced mechanical properties (an increase of 28% in bursting strength). More than 90% of the bacteria were inactivated after 40 min of green light irradiation, and more than 80% were inactivated after 60 min of white light irradiation. [ABSTRACT FROM AUTHOR]

Due to the high wastepaper recyclability and water-loop system closure, packaging paper mills struggle with increased fines, causing runnability issues. Cellulase enzymes are a preferred treatment choice for the improvement of the pulp refining in stock preparation area but are not widely used or easy to introduce in the production process. Different cellulase enzymes were tested, and those with the highest activity were introduced to the white-water (WW) samples with the aim to reduce fines content as potentially new enzyme applications on the paper machine. The first portion of the study involved the development of an experiment model to find and confirm the optimal enzyme process parameters (40 °C, pH 5.7, reaction time 3 h, and 0.18%v/v enzyme addition) for laboratory made white-water. The second portion of the study included turbidity, colloidal charge, flow cytometry (FCM), and chemical oxygen demand (COD) analysis on industrial and laboratory made white-water samples at optimized process parameters. Obtained results corresponded to reduced fines content in white-water samples, which justified commercial usage of cellulase enzymes on recycled paper machine short loop and potentially increased machine runnability without negative influence on wastewater treatment plant. [ABSTRACT FROM AUTHOR]

In this paper, by a simple hydrothermal method vertically aligned ZnO nanorod arrays were grown on the carbon fiber paper (CFP) and then through a facile chemical bath deposition method CuO nanosheets were loaded on ZnO nanorod arrays, following by thermal spraying method, carboxylated carbon nanotubes (CCNTs) were successfully integrated with CuO/ZnO@CFP to form a binder-free CuO/ZnO-CCNT@CFP sensor. The sensor shows enhanced sensing activity for baicalein and luteolin determination due to the improved structural integration and synergism of different electrode material components. Remarkably, the CuO/ZnO-CCNT@CFP sensor showed good linear relationships over wide concentration ranges of 0.03–0.70 µM and 0.70–20 µM for baicalein and 0.03–0.45 µM and 0.45–8.5 µM for luteolin detection, with the detection limits of 1.7 nM for baicalein and 0.5 nM for luteolin, respectively. More importantly, the CuO/ZnO-CCNT@CFP sensor was utilized in the simultaneous determination of baicalein and luteolin, delivering linear ranges of 0.4–14 µM (baicalein) and 0.2–6 µM (luteolin) with the limit of detection of 0.05 µM and 0.03 µM, respectively. In addition, the developed CuO/ZnO-CCNT@CFP electrode was further investigated to detect baicalein and luteolin in traditional herbal medicine samples, showing satisfied results in comparison with analytic results from high performance liquid chromatography. [ABSTRACT FROM AUTHOR]

Enzymes derived from microbial sources have gained increasing popularity in industrial applications over the past decades. Despite the high production cost, alkaline proteases have wide applications in industries such as tanneries, food production, and detergents. In recent years, there has been a shift towards utilizing natural carbon sources for cultivating microorganisms and extracting proteases in order to reduce production costs. This study aimed to investigate the biochemical and kinetic properties of protease enzymes obtained from Aspergillus niger cultivated in a paper waste medium and compare with the enzyme produced in a basal medium. Glucose is a more favorable carbon source compared to cellulose, so paper waste was pretreated with cellulose-degrading bacteria to convert cellulose into smaller carbohydrates. After the growth of A. niger in basal and combinational media, the enzymatic properties were compared between the extracted enzymes by using casein as substrate. The results demonstrated that A. niger could produce protease enzymes in the paper waste medium similar to the basal medium with more than 5-fold cost saving. The specific activity of the enzymes isolated from the basal and paper waste media was calculated to be 184.95 ± 10.56 U ml−1 and 169.88 ± 11.05 U ml−1, respectively. Carbon sources did not affect the optimum pH and temperature of the protease enzyme, which were found to be 8 and 37 °C, respectively. This study provides valuable insights into the production of alkaline protease from A. niger using a combinational medium (paper waste pretreated by cellulose-degrading bacteria), offering a cost-effective approach for industrial applications. [ABSTRACT FROM AUTHOR]

The growing demand for environmentally friendly and sustainable materials has led to the invention of innovative solutions aiming to reduce negative impacts on the environment. Mycelium-based green composites (MBCs) have become an alternative to traditional materials due to their biodegradability and various potential uses. Although MBCs are accepted as modern materials, there are concerns related to some of their physical and mechanical properties that might have limitations when they are used. This study investigates the effects of using paper waste to improve MBC properties. In this study, we investigated the physical and mechanical properties of MBCs produced from lignocellulosic materials (corn husk and sawdust) and mushroom mycelia of the genus Lentinus sajor-caju TBRC 6266, with varying amounts of paper waste added. Adding paper waste increases the density of MBCs. Incorporating 20% paper waste into corn husks led to the enhancement of the compression, bending, and impact strength of MBCs by over 20%. Additionally, it was also found that the MBCs produced from corn husk and 10% paper waste could help in reducing the amount of water absorbed into the material. Adding paper waste to sawdust did not improve MBC properties. At the same time, some properties of MBCs, such as low tensile strength and high shrinkage, might need to be further improved in the future to unlock their full potential, for which there are many interesting approaches. Moreover, the research findings presented in this publication provide a wealth of insightful information on the possibility of using paper waste to improve MBC performance and expand their suitability for a range of applications in sustainable packaging materials and various home decorative items. This innovative approach not only promotes the efficient utilization of lignocellulosic biomass but also contributes to the development of environmentally friendly and biodegradable alternatives to traditional materials. [ABSTRACT FROM AUTHOR]

Effects of cellulose nanofibers (CNF) and cationic starch (CS) were evaluated as coating components relative to the physical and mechanical properties of fluting papersheets fabricated from recycled corrugated cardboard fibers. Fabricated fluting papers were subjected to size press applications by three different coating blends. Coating suspensions were prepared at various concentrations of CNF (0.5%, 1%, 2%, 3%, and 4%) and 4 wt% CS, and the same amounts of CS/CNF. The paper sheets were fabricated using size press machine as three-time repetitive applications, followed by one-time drying section, and compared to uncoated, CScoated, and CNF-coated papers. The application of CNF suspensions increased tensile indices up to 11.7%. Moreover, CS/CNF suspensions resulted in a 67.2% increase in tensile index values. The coating of CS/CNF suspensions increased the burst index values by 163% at the CS+1%CNF concentration when compared to the control pulp. Surface application of prepared suspensions reduced the porosity of the samples under all conditions. The highest reduction in the air permeability was observed in the CS+4%CNF-coated samples as 91.5%. It can be concluded that the superficial applications of CNF on the physical and mechanical properties of recycled fluting paper was more effective in the presence of CS. [ABSTRACT FROM AUTHOR]

The widespread use of mobile devices and laptops has replaced traditional paper-based learning and the question of how the brain efficiency of digital tablet-based learning differs from that of paper-based learning remains unclear. The purpose of this study was to investigate the difference in brain efficiency for learning between paper-based and digital tablet-based learning by measuring activity in the prefrontal cortex (PFC) using functional near-infrared spectroscopy. Thirty-two subjects were randomly assigned to the paper-based learning or the digital tablet-based learning group. Subjects in each group performed a memory task that required memorizing a three-minute novel (encoding phase) on a paper or digital tablet, followed by a test in which they answered four multiple-choice questions based on the novel's content. To compare both groups, behavioral performance on the test (retrieval phase) and activity in the PFC were measured. As a result, no significant difference in behavioral performance between both groups was observed (p > 0.05). However, the paper-based learning group showed significantly lower activity in the PFC in the encoding phase than the digital tablet-based learning group (p < 0.05) but not in the retrieval phase. The current study demonstrated that brain efficiency in encoding is higher in subjects with paper-based learning than those with digital tablet-based learning. This finding has important implications for education, particularly in terms of the pros and cons of electronic document-based learning. [ABSTRACT FROM AUTHOR]

In this study, Al paper and cellulose acetate (CA) filters derived from heated tobacco waste were successfully converted into current collectors and active materials for a supercapacitor device. Typically, heated tobacco contains electrically discontinuous Al paper. First, Al was extracted from the tobacco waste using HCl to produce Lewis acid (AlCl3). This acid was then used in an Al electrodeposition process utilizing the chloroaluminate ionic liquid reaction between the acid and the base (RCl) at room temperature. To enhance the conductivity, a supplementary coating of Al metal was applied to the Al paper through electrodeposition, thus re-establishing the electrical continuity of the discontinuous parts and forming an Al-coated current collector. Moreover, the CA filters were carbonized under a nitrogen atmosphere, yielding carbon precursors (C-CA) for the supercapacitor electrodes. To further enhance the electrochemical performance, nickel oxide (NiO) was incorporated into C-CA, resulting in C-CA@NiO with pseudocapacitance. The specific surface area of CA increased with carbonization and the subsequent incorporation of NiO. The as-synthesized C-CA and C-CA@NiO materials were applied to an Al-coated current collector to obtain C-CA- and C-CA@NiO-based electrodes, exhibiting stable electrochemical behavior in the voltage range of −1.0 to 0 V and 0 to 1.0 V, respectively. An asymmetric supercapacitor (ASC) device was assembled with C-CA@NiO and C-CA as the positive and negative electrodes, respectively. This ASC device demonstrated a high specific capacitance of 40.8 F g−1, while widening the operating voltage window to 2.0 V. The high electrochemical performance of the device is attributed to the successful Al electrodeposition, which facilitates the electrical conductivity and increased porosity of the C-CA@NiO and C-CA materials. To the best of our knowledge, this is a pioneering study in regards to the conversion of biomass waste into current collectors and active materials to fabricate a practical ASC device. Our findings highlight the potential of reusing Al paper and CA filters from heated tobacco waste as essential components of energy storage devices. [ABSTRACT FROM AUTHOR]

As power sources for Internet-of-Things sensors, thermoelectric generators must exhibit compactness, flexibility, and low manufacturing costs. Stretchable and flexible painted thermoelectric generators were fabricated on Japanese paper using inks with dispersed p- and n-type single-walled carbon nanotubes (SWCNTs). The p- and n-type SWCNT inks were dispersed using the anionic surfactant of sodium dodecylbenzene sulfonate and the cationic surfactant of dimethyldioctadecylammonium chloride, respectively. The bundle diameters of the p- and n-type SWCNT layers painted on Japanese paper differed significantly; however, the crystallinities of both types of layers were almost the same. The thermoelectric properties of both types of layers exhibited mostly the same values at 30 °C; however, the properties, particularly the electrical conductivity, of the n-type layer increased linearly, and of the p-type layer decreased as the temperature increased. The p- and n-type SWCNT inks were used to paint striped patterns on Japanese paper. By folding at the boundaries of the patterns, painted generators can shrink and expand, even on curved surfaces. The painted generator (length: 145 mm, height: 13 mm) exhibited an output voltage of 10.4 mV and a maximum power of 0.21 μW with a temperature difference of 64 K at 120 °C on the hot side. [ABSTRACT FROM AUTHOR]

Tetraethoxysilane (TEOS) is the most commonly used silicon-based reinforcement agent for conserving art relics due to its cost-effectiveness and commercial maturity. However, the resulting silica gel phase is prone to developing cracks as the gel shrinks during the sol–gel process, potentially causing severe damage to the objects being treated. In this study, dodecyltrimethoxysilane (DTMS) was introduced into TEOS to minimize this shrinkage by adding elastic long chains to weaken the capillary forces. The gel formed from the DTMS/TEOS hybrid material was transparent and crack-free, featuring a dense microstructure without mesopores or micropores. It exhibited excellent thermal stability, with a glass transition temperature of up to 109.64 °C. Evaluation experiments were conducted on artificially aged, handmade bamboo paper. The TEOS-based hybrid material effectively combined with the paper fibers through the sol–gel process, polymerizing into a network structure that enveloped the paper surface or penetrated between the fibers. The surface of the treated paper displayed excellent hydrophobic properties, with no significant changes in appearance, color, or air permeability. The mechanical properties of the treated bamboo paper improved significantly, with longitudinal and transverse tensile strengths increasing by up to 36.63% and 44.25%, respectively. These research findings demonstrate the promising potential for the application of DTMS/TEOS hybrid materials in reinforcing paper relics. [ABSTRACT FROM AUTHOR]

To compare the urine Congo‐red dot paper test (CRD) with dipstick urinalysis to screen preeclampsia (PE). A total of 409 paired spot urine samples were obtained prospectively from women with suspected pre‐eclampsia attending for routine hospital visits. Congo‐red dot paper test and dipstick urinalysis were examined and compared to screen pre‐eclampsia. The agreement between the two urinary test is modest (kappa coefficient = 0.28, 95% CI 0.14–0.42). The specificity of CRD was higher than urinalysis (97.4% vs. 90.4%, p <.001). Urinalysis performed better in sensitivity (77.3% vs. 40.9%, p =.04) and the area under the receiver operating characteristic curves (AUC) (0.84 [95% CI 0.74–0.94] vs. 0.69 [95% CI 0.55–0.83], p =.04) than CRD, respectively. The sensitivity, specificity, AUC of the parallel test of them is 86.4% (64.0%–96.4%), 89.1% (85.5%–92.0%), and 0.88 (95% CI 0.79–0.96). And the serial test is 31.8% (14.7%–54.9%), 98.7% (96.8%–99.5%), 0.65 (95% CI 0.51–0.79), accordingly. The urinalysis is a better diagnosing test for preeclampsia. CRD could aid in the diagnosis of patients with preeclampsia. Combined the two tests in suspected patients may further improve the performance in the diagnosis of preeclampsia. Further study need to be made for its potential clinical practice. [ABSTRACT FROM AUTHOR]

Skin-based wearable devices have gained significant attention due to advancements in soft materials and thin-film technologies. Nevertheless, traditional wearable electronics often entail expensive and intricate manufacturing processes and rely on metal-based substrates that are susceptible to corrosion and lack flexibility. In response to these challenges, this paper has emerged with an alternative substrate for wearable electrodes due to its cost-effectiveness and scalability in manufacturing. Paper-based electrodes offer an attractive solution with their inherent properties of high breathability, flexibility, biocompatibility, and tunability. In this study, we introduce carbon nanotube-based paper composites (CPC) electrodes designed for the continuous detection of biopotential signals, such as electrooculography (EOG), electrocardiogram (ECG), and electroencephalogram (EEG). To prevent direct skin contact with carbon nanotubes, we apply various packaging materials, including polydimethylsiloxane (PDMS), Eco-flex, polyimide (PI), and polyurethane (PU). We conduct a comparative analysis of their signal-to-noise ratios in comparison to conventional gel electrodes. Our system demonstrates real-time biopotential monitoring for continuous health tracking, utilizing CPC in conjunction with a portable data acquisition system. The collected data are analyzed to provide accurate heart rates, respiratory rates, and heart rate variability metrics. Additionally, we explore the feasibility using CPC for sleep monitoring by collecting EEG signals. [ABSTRACT FROM AUTHOR]

Although membrane separation technology has been widely used in the treatment of oily wastewater, the complexity and high cost of the membrane preparation, as well as its poor stability, limit its further development. In this study, via the vacuum-assisted suction filtration method, polydopamine (PDA)-coated TiO2 nanoparticles were tightly attached and embedded on both sides of laboratory filter paper (FP). The resultant FP possessed the typical wettability of high hydrophilicity in the air with the water contact angle (WCA) of 28°, superoleophilicity with the oil contact angle (OCA) close to 0°, underwater superoleophobicity with the underwater OCA greater than 150°, and superhydrophobicity under the water with the underoil WCA over 150° for five kinds of organic solvents (carbon tetrachloride, toluene, n-hexane, n-octane, and iso-octane). The separation efficiency of immiscible oil/water, oil-in-water, and water-in-oil emulsions using the modified FP is higher than 99%. After 17 cycles of emulsion separation, a high separation efficiency of 99% was still maintained for the FP, along with good chemical and mechanical stability. In addition, successful separation and purification were also realized for the oil-in-water emulsion that contained the methylene blue (MB) dye, along with the complete degradation of MB in an aqueous solution under UV irradiation. [ABSTRACT FROM AUTHOR]

Waste wood, which has a large amount of cellulose fibers, should be transformed into useful materials for addressing environmental and resource problems. Thus, this study analyzed the application of waste wood as supercapacitor electrode material. First, cellulose fibers were extracted from waste wood and mixed with different contents of graphene nanoplatelets (GnPs) in water. Using a facile filtration method, cellulose papers with GnPs were prepared and converted into carbon papers through carbonization and then to porous activated carbon papers containing GnPs (ACP−GnP) through chemical activation processes. For the morphology of ACP−GnP, activated carbon fibers with abundant pores were formed. The increase in the amount of GnPs attached to the fiber surfaces decreased the number of pores. The Brunauer–Emmett–Teller surface areas and specific capacitance of the ACP−GnP electrodes decreased with an increase in the GnP content. However, the galvanostatic charge–discharge curves of ACPs with higher GnP contents gradually changed into triangular and linear shapes, which are associated with the capacitive performance. For example, ACP with 15 wt% GnP had a low mass transfer resistance and high charge delivery of ions, resulting in the specific capacitance value of 267 Fg−1 owing to micropore and mesopore formation during the activation of carbon paper. [ABSTRACT FROM AUTHOR]

This research explores the challenges and limitations faced at the basic level for the recycling of paper in an academic institute. It focuses on encouraging recycled paper use rather than bringing traditional virgin paper to prevent the rate of deforestation for reducing global warming. Data was collected from the academic institute via questionnaire and on-site observation and found that the institute was producing approximately 16 tons of wastepaper in a year. Besides that, another purpose of this research is to estimate the energy and assess the environmental effect by using the life cycle assessment as a tool. The results of this study revealed that traditional virgin paper derived from wood proves to be costly and less environmentally friendly than recycled paper. It also revealed that Traditional virgin paper has greater global warming, human toxicity, smog, acidification, and eutrophication potential than recycled paper. This study concludes that recycled paper does not only prove economically beneficent for any institution, but also beneficial for environment as well. [ABSTRACT FROM AUTHOR]

In this research, I established an energy benchmark for the pulp and paper industry of Vietnam. I, therefore, focus on three major paper product families, including packaging paper, printing and writing paper, and tissue paper. In this research, I use specific energy consumption (SEC) as the energy performance indicator (EnPI) for computing energy benchmarks for the main sub-sectors in the pulp and paper industry of Vietnam. The factories in the pulp and paper industry of Vietnam are divided into three production scales, and the energy benchmarks are specified by production scales. Energy surveys and energy audits have been used to calculate energy benchmarks. Here, I establish the energy benchmark for the main sub-sectors in the pulp and paper industry of Vietnam according to the three production scales. I also estimate the energy saving potential for the pulp and paper industry of Vietnam based on surveying and auditing results. [ABSTRACT FROM AUTHOR]

This study attempts to detect papers originating from the Russia‐based paper mill 'International Publisher' LLC. A total of 1,063 offers to purchase co‐authorship on a fraudulent papers published from 2019 to mid‐2022 on the 123mi.ru website were analysed. This study identifies at least 451 papers that are potentially linked to the paper mill, including one preprint, a duplication paper and 16 republications of papers erroneously published in hijacked journals. Evidence of suspicious provenance from the paper mill is provided: matches in title, number of co‐authorship slots, year of publication, country of the journal, country of a co‐authors and similarities of abstracts. These problematic papers are co‐authored by scholars from at least 39 countries and are submitted to both predatory and reputable journals. This study also demonstrates collaboration anomalies in questionable papers and examines indicators of the Russia‐based paper mill. The value of co‐authorship slots offered by 'International Publisher' LLC from 2019 to 2021 is estimated at $6.5 million. Since this study only analysed a single paper mill, it is likely that the number of papers with forged authorship is much higher. [ABSTRACT FROM AUTHOR]

Traditionally, cellulose nanofiber (CNF) production has primarily relied on virgin cellulose sources. Yet, the shift to using paper mill sludge (PMS) as a source for CNF underscores the significance of reusing and recycling industrial byproducts. PMS contains significant amounts of cellulose that can be extracted as a raw material. The purpose of present study is to provide a sustainable approach to PMS utilization as a paper coating additive in the cellulose nanofibrils (CNFPMS) form via simply scalable wire-wound rod coating method. The effect of CNFPMS additive amounts at two coating layers on microstructure and surface properties of coatings such as porosity, air permeability surface roughness and optical properties such as brightness, gloss and CIE L*a*b* is studied, which they can also provide insight for the eventual print performance. Results indicated that the obtained CNFPMS in paper coating shows 52% decrease in porosity, presenting significant improvement in the coating microstructure. The marginal increase in permeability coefficient and surface roughness, 54% and 10%, respectively, suggests improving color reproduction and preventing color density losses. Optical analysis showed slight decrease in brightness and gloss, as was expected. Notably, the lightness was improved, which also indicates increasing color gamut volume in printing applications. As a result, the current work offers a sustainable approach to manage PMS for use in paper coatings as a high-value-added material. [ABSTRACT FROM AUTHOR]

This paper comprehensively analyzes a company's supply chain design process in the pulp and paper industry. It focuses on the company's supply chain strategy, structure, operations, and performance and highlights the challenges and opportunities specific to the industry. The purpose of this case study is to show how effective supply chain design can improve a company's competitiveness and success. This paper also offers recommendations for improving supply chain design in the pulp and paper industry and other similar industries. [ABSTRACT FROM AUTHOR]

Tetra Pak® paper and PE (polyethylene) wastes were evaluated to obtain a new composite material with awareness of environmental responsibility. Fillers and coupling agents were used for this joining process. Calcite (CaCO3), boric acid (H3BO3), SPT (Sodium Perborate Tetrahydrate / NaBO3.4H2O), titanate, MAPE (maleic anhydride grafted polyethylene, and vinyltriethoxysilane (C8H18O) composites were produced in 30 x 30 cm plates. A total of 30 samples were prepared as 5 mg flour for thermogravimetric analysis (TGA). Samples were observed in a thermal analyzer at 10, 15, or 20 °C/min heating rate in nitrogen atmosphere. Graphs were obtained as a result of TGA, and the activation energies were calculated using these graphs. The activation energy was calculated using the Flynn-Wall-Ozawa method. The determined activation energies of the composites were close to each other for each temperature group. In the samples using calcite and vinyltriethoxysilane, relatively higher activation energies were observed in comparison to the samples with boric acid and MAPE. [ABSTRACT FROM AUTHOR]

A thermoelectric generator (TEG) is one of the important energy harvesting sources for wearable electronic devices, which converts waste heat into electrical energy without any external stimuli, such as light or mechanical motion. However, the poor flexibility of traditional TEGs (e.g., Si-based TE devices) causes the limitations in practical applications. Flexible paper substrates are becoming increasingly attractive in wearable electronic technology owing to their usability, environmental friendliness (disposable, biodegradable, and renewable materials), and foldability. The high water-absorbing quality of paper restricts its scope of application due to water failure. Therefore, we propose a high-performance flexible waterproof paper-based thermoelectric generator (WPTEG). A modification method that infiltrates TE materials into cellulose paper through vacuum filtration is used to prepare the TE modules. By connecting the TE-modified paper with Al tape, as well as a superhydrophobic layer encapsulation, the WPTEG is fabricated. The WPTEG with three P–N modules can generate an output voltage of up to 235 mV at a temperature difference of 50 K, which can provide power to portable electronic devices such as diodes, clocks, and calculators in hot water. With the waterproof property, the WPTEG paves the way for achieving multi-scenario applications in humid environments on human skin. [ABSTRACT FROM AUTHOR]

This paper describes the fabrication and characterization of porous SiC ceramics derived from highly-filled preceramic papers. The SiC ceramics were obtained by spark plasma sintering of stacked preceramic papers at temperatures of 2100 and 2200 °C under pressures of 5–60 MPa for 10 min. The microstructure and phase composition were analyzed by scanning electron microscopy and X-ray diffraction, respectively. Gas permeation tests were performed using hydrogen permeation cell at room temperature. It is revealed that the porosity of sintered SiC can be varied from 9 to 45 % depending on the sintering parameters. The shrinkage of the materials during spark plasma sintering occurs in four stages. The linear shrinkage value of the material increases from 7 to 47 % at 2100 °C and from 20 to 50 % for the samples sintered at 2100 and 2200 °C, respectively. Correlation dependencies between porosity and mechanical properties of the fabricated SiC were established. The obtained porous SiC ceramics exhibit high bending strength of 165 MPa and gas permeation flux of 78 molH 2 /m2/s at the porosity of 36 % that make it suitable for ceramic-based membranes. [ABSTRACT FROM AUTHOR]

The notable increase in retraction papers has attracted considerable attention from diverse stakeholders. Various sources are now offering information related to research integrity, including concerns voiced on social media, disclosed lists of paper mills, and retraction notices accessible through journal websites. However, despite the availability of such resources, there remains a lack of a unified platform to consolidate this information, thereby hindering efficient searching and cross-referencing. Thus, it is imperative to develop a comprehensive platform for retracted papers and related concerns. This article aims to introduce "Amend," a platform designed to integrate information on research integrity from diverse sources. The Amend platform consolidates concerns and lists of problematic articles sourced from social media platforms (e.g., PubPeer, For Better Science), retraction notices from journal websites, and citation databases (e.g., Web of Science, CrossRef). Moreover, Amend includes investigation and punishment announcements released by administrative agencies (e.g., NSFC, MOE, MOST, CAS). Each related paper is marked and can be traced back to its information source via a provided link. Furthermore, the Amend database incorporates various attributes of retracted articles, including citation topics, funding details, open access status, and more. The reasons for retraction are identified and classified as either academic misconduct or honest errors, with detailed subcategories provided for further clarity. Within the Amend platform, a total of 32,515 retracted papers indexed in SCI, SSCI, and ESCI between 1980 and 2023 were identified. Of these, 26,620 (81.87%) were associated with academic misconduct. The retraction rate stands at 6.64 per 10,000 articles. Notably, the retraction rate for non-gold open access articles significantly differs from that for gold open access articles, with this disparity progressively widening over the years. Furthermore, the reasons for retractions have shifted from traditional individual behaviors like falsification, fabrication, plagiarism, and duplication to more organized large-scale fraudulent practices, including Paper Mills, Fake Peer-review, and Artificial Intelligence Generated Content (AIGC). The Amend platform may not fully capture all retracted and concerning papers, thereby impacting its comprehensiveness. Additionally, inaccuracies in retraction notices may lead to errors in tagged reasons. Amend provides an integrated platform for stakeholders to enhance monitoring, analysis, and research on academic misconduct issues. Ultimately, the Amend database can contribute to upholding scientific integrity. This study introduces a globally integrated platform for retracted and concerning papers, along with a preliminary analysis of the evolutionary trends in retracted papers. [ABSTRACT FROM AUTHOR]

Fluorescent sensors with single reading are generally subject to unpredictable disturbs from environmental and artificial factors. In order to overcome this barrier of detection reliability, a paper-based optical sensor with proportional fluorescence was established and further combined with a smartphone for visual, on-site and quantitative detection of Fe3+, which affects the color, smell and taste of water, and endangers the health of plants and animals. The ratio fluorescent probe was fabricated by rhodamine B and carbon quantum dots derived from xylan. The red fluorescence of rhodamine B was inert to Fe3+, which was referred to as background. And blue emitting carbon quantum dots functioned as signal report units, which would be quenched by Fe3+ and make the fluorescence of the ratio probe change from purple to red. The quantitative detection of Fe3+ was conducted by investigating the RGB value of fluorescent images with a smartphone. With the increase of Fe3+ concentration, the R/B (red/blue) value of the fluorescent paper gradually increased. The linear detection range was 10–180 μM, and the limit of detection was 198.2 nM. The application of ratio fluorescent paper with a smartphone provides a facile method for the rapid detection of ions. [ABSTRACT FROM AUTHOR]

This paper presents a comprehensive review of the literature on electronic reading (e-reading) versus paper reading. The main objective was to assess the current state of research comparing digital and paper reading outcomes among students aged 6–18 years old, as well as assessing the impact of various factors (gender, socioeconomic status, and school location) in explaining the differences between the two modes. Inclusion criteria included the following: participants (6–18 years), research focus (comparing digital reading and paper reading), study type (quantitative or mixed methods), publication (peer reviewed between 2015 and 2022), and language (English). A systematic search in four databases (WOS, Scopus, ERIC, and JSTOR) in August 2022 was conducted by three reviewers. The search revealed 23 studies matching the inclusion criteria. The findings from the reviewed studies are diverse, with some reporting no significant differences in reading comprehension between the two modes, while others suggest screen inferiority, thereby favoring paper reading. Individual-level predictors, such as prior comprehension skills and reading habits, play a crucial role in determining reading performance across modes. Family-level factors, such as the number of books at home, and school-level factors, like the usage of ICT resources, influence both paper and digital reading comprehension. Moreover, gender differences in attitudes and performance towards different reading modes are apparent. SES is positively associated with reading achievement in both modes, with a larger effect shown for paper reading. Overall, the comparison between electronic and paper reading modes reveals a complex interplay of individual and contextual factors influencing reading comprehension and attitudes. [ABSTRACT FROM AUTHOR]

Creatinine is one of the most important biomarkers to detect renal failures. The electrochemical detection of creatinine has been performed using complex enzymatic and non-enzymatic electrode arrays hindering their commercialization. In this work, a new and practical non-enzymatic electrochemical sensor was fabricated depositing copper on carbon paper electrodes by physical vapor deposition (namely Cu/CP). Surface and cross-sectional SEM images demonstrated the deposition of copper over the 3D structure of carbon paper. A thin film was found on the surface, while Cu nanowires with diameters of 180 ± 30 nm were found inside the 3D structure of CP. The thickness of the Cu film on the tubular structures of CP was of 390 ± 40 nm. High-resolution TEM images indicated that the Cu film was integrated by hierarchical structures containing terminal Cu hemispheres of 17.6 ± 2.2 nm. Additionally, interplanar distances from the selected-area electron diffraction pattern demonstrated the presence of Cu0, while Cu2O was also found. Creatinine concentrations in saliva between 16 and 400 µM indicate kidney failure. The Cu/CP electrochemical sensor detected creatinine with linear concentration ranges from 0 to 1000 µM with a r2 = 0.9936. Outstandingly, this sensor presented good reproducibility (RSD = 7.3%), and selectivity to detect creatinine in artificial saliva using interferents like urea, glucose, glycine, ascorbic and uric acids. [ABSTRACT FROM AUTHOR]

In the process of conservation mounting, starch paste made from wheat flour is the glue of choice to paste reinforcing strips and backing papers, often Xuan paper, for mending and decorating aged and damaged paper-based Chinese artworks. To keep objects intact and select appropriate conservation materials, this research explored the applicability of near-infrared (NIR) spectroscopy coupled with multivariate analysis for the characterization of contemporary unsized Xuan paper with and without starch. In particular, partial least squares (PLS) regression was used to predict the degree of polymerization (DP) of the paper, i.e., one of the most important properties of paper materials, and principal component analysis (PCA) was used to detect starch and to distinguish between papers with different amounts of starch. Using 12 contemporary unsized Xuan papers, the NIR-PLS method for DP prediction was validated, and the best-performed model was generated using the logarithmic transformation of DP−1 as a response variable, with root mean square error of prediction (RMSEP) of DP 128. The NIR-PCA method was also found to be applicable to separate starch-free papers and papers treated with starch, and the results indicate that the higher the content of starch, the better PCA classification performs. This research provides supporting data for the non-destructive characterization of Xuan paper-based objects and differentiates between Xuan paper before and after treatment with starch. [ABSTRACT FROM AUTHOR]

Sulfite, a widely used food additive, is subject to regulated labeling. The extraction of sulfite as the stable hydroxymethylsulfonate (HMS) form and its quantitative analysis by liquid chromatography-tandem mass spectrometry (LC-MS/MS) has been recognized for their good sensitivity, selectivity, and versatility across various food materials. This study aimed to develop a cost-effective and simpler method for sulfite quantitation, while maintaining the superior sensitivity and selectivity of mass spectrometry (MS). To achieve this, we introduced paper spray ionization (PSI), an ambient desorption ionization technique that could achieve the direct measurement of analytes without employing separation. We also employed a novel internal standard (IS) structurally similar to the analyte, replacing the more expensive isotopically labeled IS. Although the PSI-MS/MS method developed in this study exhibited slightly lower analytical performance compared to the conventional LC-MS/MS, it remained effective for sulfite analysis in dried fruits. [ABSTRACT FROM AUTHOR]

Purpose: Paper-based artifacts hold significant cultural and social values. However, paper is intrinsically fragile to microorganisms, such as mold, due to its cellulose composition, which can serve as a microorganisms' nutrient source. Mold not only can damage papers' structural integrity and pose significant challenges to conservation works but also may subject individuals attending the contaminated artifacts to health risks. Current approaches for strain identification usually require extensive training, prolonged time for analysis, expensive operation costs, and higher risks of secondary damage due to sampling. Thus, in current conservation practices with mold-contaminated artifacts, little pre-screening or strain identification was performed before mold removal, and the cleaning techniques are usually broad-spectrum rather than strain-specific. With deep learning showing promising applications across various domains, this study investigated the feasibility of using a convolutional neural network (CNN) for fast in-situ recognition and classification of mold on paper. Methods: Molds were first non-invasively sampled from ancient Xuan Paper-based Chinese books from the Qing and Ming dynasties. Strains were identified using molecular biology methods and the four most prevalent strains were inoculated on Xuan paper to create mockups for image collection. Microscopic images of the molds as well as their stains situated on paper were collected using a compound microscope and commercial microscope lens for cell phone cameras, which were then used for training CNN models with a transfer learning scheme to perform the classification of mold. To enable involvement and contribution from the research community, a web interface that actuates the process while providing interactive features for users to learn about the information of the classified strain was constructed. Moreover, a feedback functionality in the web interface was embedded for catching potential classification errors, adding additional training images, or introducing new strains, all to refine the generalizability and robustness of the model. Results & Conclusion: In the study, we have constructed a suite of high-confidence classification CNN models for the diagnostic process for mold contamination in conservation. At the same time, a web interface was constructed that allows recurrently refining the model with human feedback through engaging the research community. Overall, the proposed framework opens new avenues for effective and timely identification of mold, thus enabling proactive and targeted mold remediation strategies in conservation. [ABSTRACT FROM AUTHOR]

Oil–paper insulation is the critical insulation element in the modern power system. Under a harsh operating environment, oil–paper insulation will deteriorate gradually, resulting in electrical accidents. Thus, it is important to evaluate and monitor the insulation state of oil–paper insulation. Firstly, this paper introduces the geometric structure and physical components of oil–paper insulation and shows the main reasons and forms of oil–paper insulation's degradation. Then, this paper reviews the existing condition assessment techniques for oil–paper insulation, such as the dissolved gas ratio analysis, aging kinetic model, cellulose–water adsorption isotherm, oil–paper moisture balance curve, and dielectric response technique. Additionally, the advantages and limitations of the above condition assessment techniques are discussed. In particular, this paper highlights the dielectric response technique and introduces its evaluation principle in detail: (1) collecting the dielectric response data, (2) extracting the feature parameters from the collected dielectric response data, and (3) establishing the condition assessment models based on the extracted feature parameters and the machine learning techniques. Finally, two full potential studies are proposed, which research hotspots' oil–paper insulation and the electrical–chemical joint evaluation technique. In summary, this paper concludes the principles, advantages and limitation of the existing condition assessment techniques for oil–paper insulation, and we put forward two potential research avenues. [ABSTRACT FROM AUTHOR]

A novel electrochemical sensor for paraquat determination was facilely developed using nanocomposites of cellulose incorporated with manganese oxide (MnO2@cellulose) modified screen-printed carbon electrode (SPCE). In this study, SPCE was fabricated on a low-cost poster paper, and nanocellulose from sugarcane bagasse was employed to enhance the electrode's surface area and improve the dispersion of MnO2. The MnO2@cellulose modified poster-SPCE exhibited a high electrochemical response toward paraquat. Various influencing factors, including differential pulse voltammetric parameters and accumulation time, were systematically explored. Under the optimal conditions, the cathodic peak current was linearly proportional to paraquat concentration in a range of 2 to 200 µM, featuring a low detection limit of 1 µM. The proposed sensor offers cost-effectiveness and can be readily prepared via a simple procedure. Moreover, this method exhibits excellent reproducibility, high selectivity, and a short analysis time. The portable electrochemical sensor was able to determine paraquat in water samples with acceptable recoveries from 95.45 to 109.20%, indicating that the sensor based on MnO2@cellulose/SPCE is reliable for paraquat quantification. [ABSTRACT FROM AUTHOR]