Search

The shear characteristics of the interfaces between soil and concrete structures are essential for the safety of the structures. In this study, a large-scale direct shear test apparatus was developed to measure the mechanical parameters of soil–concrete interfaces under conditions with different soil types, soil moisture contents, and interfacial filling materials. The results showed that the shear stress of the soil–concrete interface increased initially and then became stable with the increase in the shear displacement. The shear displacement of the sandy soil when the shear stress became stable was smaller than that of the clayey soil. The silty sand–concrete interface had a smaller friction angle than the interface with the medium-coarse sand. Moreover, with the increase in the soil moisture content, the friction angle of the clayey soil–concrete interface decreased rapidly, whereas the cohesion first increased and then decreased, and the peak cohesion was near the plastic limit of the soil. Under the same moisture content, the friction angle and cohesion of the clay–concrete interface was reduced by filling the interface with a thin layer of sandy soil, while filling the silty sand–concrete interface with a thin layer of silt reduced the friction angle and increased the interfacial cohesion. Nonetheless, the filling had little impact on the overall shear strength of the interface. [ABSTRACT FROM AUTHOR]

The physical and mechanical behavior of soil polymer composites tightly depends on the properties and structures of both soil and polymer. This study aims to investigate the effect of glass transition temperature as one of the most important characteristics of adhesive resins of acrylic polymers on the geotechnical behavior of soils that have not been fully covered by previous studies. To achieve that, three similar copolymers of methyl methacrylate-co-butyl acrylate with different glass-transition temperatures of 1°C, 33°C, and 51°C were synthesized, and two representative specimens of cohesive (kaolinite clay) and noncohesive (sand) soils were chosen to perform a full investigation of the consequential changes in the physical and mechanical behavior. A series of laboratory tests, including the Atterberg limits tests, the unconfined compressive strength tests, direct shear tests in soaked and unsoaked conditions, swelling tests, and odometer tests, were conducted on untreated and treated soils with synthesized polymers. The results showed a salient enhancement in the cohesion and the unconfined compressive strength value of both soils. However, the polymer with a glass-transition temperature near to ambient temperature led to a greater increase in the compressive and shear strength of stabilized soil among its peers. Samples treated with the polymer having the lowest glass transition temperature revealed a more compression index (i.e., obtained from odometer tests) and lower unconfined compressive strength. It is also observed that the swelling index and swelling pressure decreased marginally with increasing the glass transition temperature. [ABSTRACT FROM AUTHOR]

Copyright of Canadian Geotechnical Journal is the property of Canadian Science Publishing and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

There are various methods for improving the engineering properties of weak soils among which the usage of chemical additives is one of the most important ones. Considering sepiolite as an environmental friendly material and its unique physiochemical characteristics, this substance has been used as an additive for soil improvement in this study. For this purpose, in addition to soil identification tests, in order to examine the effect of changes in the percentage of sepiolite additive, a set of tests has been done including Atterberg limits, modified compaction, uniaxial compressive strength, pH, direct shear and permeability test on sandy clay and clayey sand soils. Furthermore, scanning electron microscopy (SEM) and x-ray diffraction (XRD) tests have been performed to investigate the microstructure of non-stabilized and stabilized soil. According to the results, with increasing the additive percentage and the curing time, the uniaxial compressive strength of the soil increased. The uniaxial strength in the clayey sand soil rose up to six times larger than that of the initial strength of the soil. However, the maximum strength enhancement in the sandy clay soil was up to three times the initial value. Sepiolite (above 5%) has improved soil shear strength parameters including cohesion and internal friction angle. The increase in the additive content led to diminished permeability in soil. Further, the elevation of the sepiolite content in the soil resulted in enhanced liquid and plastic limits of soil. Microstructural investigations indicated that the reason of improvement in strength parameters of soil was the incidence of chemical reactions including ion exchange, flocculation and production of calcium-silicate-hydrate (CSH) and calcium-aluminate-hydrate (CAH) gels. Further, sepiolite fiber resulted in enhanced strength by filling the pores and void spaces of soil. • Sepiolite is an environmentally friendly material to stabilize the soils. • Increasing the sepiolite content during the curing time, increases UCS of the soil. • Sepiolite fibers act like bridges and connect different parts of soil. • CSH and CAH are products of chemical reactions between sepiolite and soil. [ABSTRACT FROM AUTHOR]

Focuses on a study that discussed a four-parameter model that can represent the shear modulus factors and damping coefficients for granular soils. Information on nonlinear soil behavior; Effect of confining pressure on modulus and damping; Experimental data on cohesionless soils; Details on the MIT-S1 stress soil model for clays and sands.

The inclusion of sand columns results in enhancing the bearing capacity of clayey soil, increase the rate of consolidation, presentation of liquefaction in loose sandy soils and provide lateral resistance against the horizontal movement. This research aims at investigating the effects of floating columns in clayey soil with silty deposits by developing small scale laboratory models. The effects of sand columns on soils of different shear strengths, slenderness ratio (L/D) of columns were investigated. Group effect was also investigated by varying spacing between the columns. Experimental results were compared with the numerical analysis results. A 15-noded triangular mesh was generated using a finite element tool PLAXIS 2D. Finite element analysis was performed using Mohr's Coulomb's criterion considering undrained analysis for soft clayey soil and drained analysis for sand columns. It was concluded that the sand columns can significantly increase the ultimate loading capacity of soft soils. Results show that critical length for floating column ranges from 4 to 5.5 times the diameter of the column, beyond which bulging occurs and loading capacity decreased. The effect of group was also investigated and observed that with high spacing between the sand columns, the group efficiency decreased. The axial capacity of sand columns decreases while increasing spacing between the columns. [ABSTRACT FROM AUTHOR]