Search

Flexible zinc-silver oxide (Zn-Ag 2 O) batteries have attracted extensive attention for comfortable wearable electronics owing to their stable output voltage, inherent safety, and environmental benignity. However, they suffer from inferior specific capacity and poor mechanical stability due to the low utilization of Ag 2 O cathodic material and weak interfacial adhesion of active material/substrate. Inspired by the nature of the tree root system, we develop an interface-engineered cathode, in which Ag 2 O nanoparticles are rooted on an Au, Ni co-modified filter paper substrate (CFP) through an electroless plating followed by an in situ electrochemical oxidation. The staggered-stacked Ag 2 O nanoparticles provide abundant electrochemically active sites and convenient ion diffusion paths, and the unique biological tree-root-like structure of the electrode material creates robust interlocking interfaces. A quasi-solid-state Zn-Ag 2 O battery assembled with a tree-root-like Ag 2 O/CFP cathode delivers a high areal specific capacity of 1.08 mAh cm -2 and long-term cycling durability with a capacity retention of 77.3% even after 100 cycles. Moreover, the device presents good mechanical stability under various flexural deformations, including bending, folding, and twisting, and exhibits minimal capacity changes after 1000 bending cycles. These findings suggest that the bio-inspired interface-engineered electrode structure is an efficient approach for developing flexible batteries with excellent electrochemical performance and mechanical properties., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2022 Elsevier Inc. All rights reserved.)

The role of humidity sensors in different industries and field applications, such as agriculture, food monitoring, biomedical equipment, heating, and ventilation, is well known. However, most commercially available humidity sensors are based on polymers or electronic materials that are not degradable and thus contribute to electronic waste. Here, we report a low-cost, flexible, easy-to-fabricate, and eco-friendly parallel-plate capacitive humidity sensor for field applications. The sensor is fabricated from copper tape and tissue paper, where copper tape is used to create the plates of the capacitor, and tissue paper is used as a dielectric sensing layer. Along with the low cost, the high sensitivity, better response and recovery times, stability, and repeatability make this sensor unique. The sensor was tested for relative humidity (RH), ranging from 40% to 99%, and the capacitance varied linearly with RH from 240 pF to 720 pF, as measured by an Arduino. The response time of the sensor is ~1.5 s, and the recovery time is ~2.2 s. The experiment was performed 4-5 times on the same sensor, and repeatable results were achieved with an accuracy of ±0.1%. Furthermore, the sensor exhibits a stable response when tested at different temperatures. Due to the above advantages, the presented sensor can find ready applications in different areas.

Pencils and papers are ubiquitous in our society and have been widely used for writing and drawing, because they are easy to use, low-cost, widely accessible, and disposable. However, their applications in emerging skin-interfaced health monitoring and interventions are still not well explored. Herein, we report a variety of pencil-paper-based on-skin electronic devices, including biophysical (temperature, biopotential) sensors, sweat biochemical (pH, uric acid, glucose) sensors, thermal stimulators, and humidity energy harvesters. Among these devices, pencil-drawn graphite patterns (or combined with other compounds) serve as conductive traces and sensing electrodes, and office-copy papers work as flexible supporting substrates. The enabled devices can perform real-time, continuous, and high-fidelity monitoring of a range of vital biophysical and biochemical signals from human bodies, including skin temperatures, electrocardiograms, electromyograms, alpha, beta, and theta rhythms, instantaneous heart rates, respiratory rates, and sweat pH, uric acid, and glucose, as well as deliver programmed thermal stimulations. Notably, the qualities of recorded signals are comparable to those measured with conventional methods. Moreover, humidity energy harvesters are prepared by creating a gradient distribution of oxygen-containing groups on office-copy papers between pencil-drawn electrodes. One single-unit device (0.87 cm 2 ) can generate a sustained voltage of up to 480 mV for over 2 h from ambient humidity. Furthermore, a self-powered on-skin iontophoretic transdermal drug-delivery system is developed as an on-skin chemical intervention example. In addition, pencil-paper-based antennas, two-dimensional (2D) and three-dimensional (3D) circuits with light-emitting diodes (LEDs) and batteries, reconfigurable assembly and biodegradable electronics (based on water-soluble papers) are explored., Competing Interests: The authors declare no competing interest.

Abstract Materials that provide dynamically tunable infrared (IR) response are important for many applications, including active camouflage and thermal management. However, current IR-tunable systems often exhibit limitations in mechanical properties or practicality of their tuning modalities, or require complex and costly fabrication methods. An additional challenge relates to providing compatibility between different spectral channels, such as allowing an object to be reversibly concealed in the IR without making it appear in the visible range. Here, we demonstrate that conducting polymer-cellulose papers, fabricated through a simple and cheap approach, can overcome such challenges. The papers exhibit IR properties that can be electrochemically tuned with large modulation (absolute emissivity modulation of 0.4) while maintaining largely constant response in the visible range. Owing to high ionic and electrical conductivity, the tuning of the top surface can be performed electrochemically from the other side of the paper even at tens of micrometer thicknesses, removing the need for overlaying electrode and electrolyte in the optical beam path. These features enabled a series of electrically tunable IR devices, where we focus on demonstrating dynamic radiative coolers, thermal camouflage, anti-counterfeiting tags, and grayscale IR displays. The conducting polymer-cellulose papers are sustainable, cheap, flexible and mechanically robust, providing a versatile materials platform for active and adaptive IR optoelectronic devices.

Loop-mediated isothermal amplification (LAMP) has been widely used to detect many infectious diseases. However, minor inconveniences during the steps of adding reaction ingredients and lack of simple color results hinder point-of-care detection. We therefore invented a fluorometric paper-based LAMP by incorporating LAMP reagents, including a biotinylated primer, onto a cellulose membrane paper, with a simple DNA fluorescent dye incubation that demonstrated rapid and accurate results parallel to quantitative polymerase chain reaction (qPCR) methods. This technology allows for instant paper strip detection of methicillin-resistant Staphylococcus aureus (MRSA) in the laboratory and clinical samples. MRSA represents a major public health problem as it can cause infections in different parts of the human body and yet is resistant to commonly used antibiotics. In this study, we optimized LAMP reaction ingredients and incubation conditions following a central composite design (CCD) that yielded the shortest reaction time with high sensitivity. These CCD components and conditions were used to construct the paper-based LAMP reaction by immobilizing the biotinylated primer and the rest of the LAMP reagents to produce the ready-to-use MRSA diagnostic device. Our paper-based LAMP device could detect as low as 10 ag (equivalent to 1 copy) of the MRSA gene mecA within 36-43 min, was evaluated using both laboratory (individual cultures of MRSA and non-MRSA bacteria) and clinical blood samples to be 100% specific and sensitive compared to qPCR results, and had 35 day stability under 25 °C storage. Furthermore, the color readout allows for quantitation of MRSA copies. Hence, this device is applicable for point-of-care MRSA detection.

Background: Accurate quantification of pain in a clinical setting is vital. The use of an electronic pain scale enables data to be collected, analyzed, and utilized much faster compared with traditional paper-based scales. The advancement of smart technology in pediatric and adult pain evaluation may offer opportunities to introduce easy-to-use and reliable pain assessment methods within different clinical settings. If promptly introduced within different pediatric and adult pain clinic services, validated and easily accessible mobile health pain apps may lead to early pain detection, promoting improvement in patient's quality of life and leading to potentially less time off from school or work., Objective: This cross-sectional observational study aimed to investigate the interchangeability of an electronic visual analog scale (eVAS) app with a traditional paper visual analog scale (pVAS) among Australian children, adolescents, and adults for pain evaluation., Methods: Healthy participants (age range 10-75 years) were recruited from a sporting club and a secondary school in Melbourne (Australia). The data collection process involved application of pressure (8.5 kg/cm 2 ) from a Wagner Force Dial FDK 20 to the midpoint of the thumb. The pressure was applied twice with a 5-minute interval. At each pressure application, participants were asked to randomly record their pain perception using the "eVAS" accessible via the "Interactive Clinics" app and the traditional pVAS. Statistical analysis was conducted to determine intermethod and intramethod reliabilities., Results: Overall, 109 healthy participants were recruited. Adults (mean age 42.43 years, SD 14.50 years) had excellent reliability, with an intraclass correlation coefficient (ICC) of 0.94 (95% CI 0.91-0.96). Children and adolescents (mean age 13.91 years, SD 2.89 years) had moderate-to-good intermethod and intramethod reliabilities, with an ICC of 0.80 (95% CI 0.70-0.87) and average ICC of 0.80 (95% CI 0.69-0.87), respectively., Conclusions: The eVAS app appears to be interchangeable compared with the traditional pVAS among children, adolescents, and adults. This pain evaluation method may offer new opportunities to introduce user-friendly and validated pain assessment apps for patients, clinicians, and allied health professionals., (©Alexandra Turnbull, Dean Sculley, Carles Escalona-Marfil, Lluís Riu-Gispert, Jorge Ruiz-Moreno, Xavier Gironès, Andrea Coda. Originally published in the Journal of Medical Internet Research (http://www.jmir.org), 17.09.2020.)

Here we present an alternative technological approach to paper-based microfluidics that, to the best of our knowledge, has not been reported so far. Instead of defining fluid conducting paths by cutting fluidic structures, or by printing hydrophobic substances on paper, we prepare cellulose/polymer composites that can be printed additively on, in principle, arbitrarily shaped substrates and surfaces. In this way, with respect to geometry and properties, well defined fluid conducting structures based on cellulose can be realized, that can additionally be fully embedded in an organic surface coating. Moreover, the composite can, prior to the printing step, be doped with a functional component, which facilitates the realization of printed analytical devices using just a single base material and process technology. In this sense, the proposed technology can be seen as an alternative pathway to paper-based microfluidics, that may be attractive for specific niche-applications such as, for example, bio-chemical assays embedded in the surface of everyday necessities or commodities. Especially lateral flow immunoassays, pandemic-driven needed in large quantities, may embody a future application field of the presented technology.

Abstract Paper-based electronics have attracted much attention due to their softness, degradability, and low cost. However, paper-based sensors are difficult to apply to high-humidity environments or even underwater. Here, we report a fully paper-integrated piezoresistive sensing system that exhibits flexibility, waterproofing, air permeability, and biocompatibility. This system consists of hydrophobic paper as the substrate and encapsulation layer, conductive paper with a double ‘zig-zag’ and dotted surface structure as the sensing layer, and silver paste films as the interconnects. The structural design of the sensing layer helps to increase the contact area in adjacent layers under pressure and further improves the pressure sensitivity. The piezoresistive system can be worn on human skin in the ambient environment, wet environment, and water for real-time monitoring of physiological signals with air permeability and waterproofing due to its hydrophobic fiber structure. Such a device provides a reliable, economical, and eco-friendly solution to wearable technologies.

Abstract Nowadays, recommender system has become one of the main tools to search for users’ interested papers. Since one paper often contains only a part of keywords that a user is interested in, recommender system returns a set of papers that satisfy the user’s need of keywords. Besides, to satisfy the users’ requirements of further research on a certain domain, the recommended papers must be correlated. However, each paper of an existing paper citation network hardly has cited relationships with others, so the correlated links among papers are very sparse. In addition, while a mass of research approaches have been put forward in terms of link prediction to address the network sparsity problems, these approaches have no relationship with the effect of self-citations and the potential correlations among papers (i.e., these correlated relationships are not included in the paper citation network as their published time is close). Therefore, we propose a link prediction approach that combines time, keywords, and authors’ information and optimizes the existing paper citation network. Finally, a number of experiments are performed on the real-world Hep-Th datasets. The experimental results demonstrate the feasibility of our proposal and achieve good performance.

OBJECTIVES: Existing electronic data capture options are often financially unfeasible in resource-poor settings or difficult to support technically in the field. To help facilitate large-scale multicenter studies in sub-Saharan Africa, the African Partnership for Chronic Disease Research (APCDR) has developed an open-source electronic questionnaire (EQ). STUDY DESIGN AND SETTING: To assess its relative validity, we compared the EQ against traditional pen-and-paper methods using 200 randomized interviews conducted in an ongoing type 2 diabetes case-control study in South Africa. RESULTS: During its 3-month validation, the EQ had a lower frequency of errors (EQ, 0.17 errors per 100 questions; paper, 0.73 errors per 100 questions; P-value ≤0.001), and a lower monetary cost per correctly entered question, compared with the pen-and-paper method. We found no marked difference in the average duration of the interview between methods (EQ, 5.4 minutes; paper, 5.6 minutes). CONCLUSION: This validation study suggests that the EQ may offer increased accuracy, similar interview duration, and increased cost-effectiveness compared with paper-based data collection methods. The APCDR EQ software is freely available (https://github.com/apcdr/questionnaire).

Abstract Flexible sensors have recently attracted much attention for potential applications in motion measurement and wearable health monitoring. In this paper, an environment-friendly, economic, and high-performance paper-based self-inductive folding displacement sensor (PSIFS) was proposed, with displacement resolution of 20 μm and wide measurement range of 43.2 mm. The sensor sensitivity could reach 4.44% mm−1 with the maximum deviation of 0.00904 in experiments. The sensing mechanism based on inductance variation due to three-dimensional deformation of planar inductor coil and structural design principle under two dimensions of sensitivity and size were proposed and studied. The folding method to enhance sensitivity was proposed and 3 times sensitivity enhancement could be achieved by once folding. Multiple breathing states and motion states of the human joints could be recognized. The proposed simple paper-based sensor, folding method to increase sensitivity, and structural design model may provide a way for the research of flexible sensors.

Questions are used to obtain information, stimulate thinking, and redirect reasoning. Academics in higher education use questions on a daily basis to stimulate thinking and reasoning in students. Final examination papers are used by academics to assess the retention and application skills of students. The assumption, however, exists that questions relating to application skills at universities of technology should start to dominate the higher academic levels in education, with a subsequent drop in questions regarding retention skills. These questions may be categorized as either higher order or lower order questions. This article attempts to distinguish between these two types of questions in light of Bloom's taxonomy, with similar concepts such as deep and surface learning being examined. The literature review is applied to an electrical engineering module titled Electronics, which serves as the case study. The results of this study indicate that a high percentage of the final examination papers dealt with the objective "Application," where students had to make use of numerous mathematical equations to solve various unknowns. The results also indicated that academics in electronics are using more lower order than higher order questions in their final examination papers. A balance is suggested between these two types of questions for various academic levels at universities of technology. (Contains 3 tables and 1 figure.)

Abstract Paper-based electrochemical sensors provide the opportunity for low-cost, portable and environmentally friendly single-use chemical analysis and there are various reports of surface-functionalized paper electrodes. Here we report a composite paper electrode that is fabricated through designed papermaking using cellulose, carbon fibers (CF), and graphene oxide (GO). The composite paper has well-controlled structure, stable, and repeatable properties, and offers the electrocatalytic activities for sensitive and selective chemical detection. We demonstrate that this CF/GO/cellulose composite paper can be reduced electrochemically using relatively mild conditions and this GO reduction confers electrocatalytic properties to the composite paper. Finally, we demonstrate that this composite paper offers sensing performance (sensitivity and selectivity) comparable to, or better than, paper-based sensors prepared by small-batch surface-modification (e.g., printing) methods. We envision this coupling of industrialized papermaking technologies with interfacial engineering and electrochemical reduction can provide a platform for single-use and portable chemical detection for a wide range of applications.

Abstract Paper, as a foldable, pollution-free, and low-cost material, has become a suitable support substrate for producing flexible thermoelectric (TE) generators to realize waste heat recycling and the application of human-powered electronic devices. We propose a facile fabrication method to modify cellulose paper with inorganic TE powders via vacuum filtration, making a modified paper that possesses good thermoelectric properties. By connecting the modified paper to copper foils, flexible paper-based TE generators (PTGs) are fabricated. The obtained PTG with three units of P–N modules can generate an output voltage of ∼41.2 mV at a temperature difference of 50 K. Based on this modified paper, a thermal sensor that responds to heat sources, such as fingers, is proposed with a rapid response time of 0.25 s. This work offers a promising strategy for the simple fabrication of PTGs, paving the way for achieving the commercial application of self-powered wearable electronics.

Aiming at the problem of poor image contrast and loss of visual information on electrowetting electronic paper display， this paper proposes an image hierarchical mapping technique based on human visual system. Firstly, the image is decomposed into the base layer and the detail layer, and the brightness of the base layer is enhanced. Then, the enhanced image is partitioned by Weber-Fechner law to realize the partition logarithmic mapping, and weighted and merged with the detail layer as the output image. At the same time, in order to achieve precise modulation of the electrowetting display, the brightness is local linearly stretched. The experimental results show that compared with traditional mapping methods, the entropy value of the algorithm in this paper is closer to the original map, the PSNR,SSIM and UIQI values of image evaluation index are respectively improved by 0.2~0.6，0.07~0.4 and 0.1~0.6. The method makes the relationship between the corrected voltage and brightness more linear, increases the image details on the electrowetting electronic paper, improves the contrast, and the overall visual effect is better.

AbstractSixth generation will exploit satellite, aerial, and terrestrial platforms jointly to improve radio access capability and unlock the support of on‐demand edge cloud services in three‐dimensional (3D) space, by incorporating mobile edge computing (MEC) functionalities on aerial platforms and low‐orbit satellites. This will extend the MEC support to devices and network elements in the sky and forge a space‐borne MEC, enabling intelligent, personalized, and distributed on‐demand services. End users will experience the impression of being surrounded by a distributed computer, fulfilling their requests with apparently zero latency. In this paper, we consider an architecture that provides communication, computation, and caching (C3) services on demand, anytime, and everywhere in 3D space, integrating conventional ground (terrestrial) base stations and flying (non‐terrestrial) nodes. Given the complexity of the overall network, the C3 resources and management of aerial devices need to be jointly orchestrated via artificial intelligence‐based algorithms, exploiting virtualized network functions dynamically deployed in a distributed manner across terrestrial and non‐terrestrial nodes.

Abstract The increasing demands to further electrify and digitalize our society set demands for a green electrical energy storage technology that can be scaled between very small, and heavily distributed electrical energy sources, to very large volumes. Such technology must be compatible with fast-throughput, large-volume and low-cost fabrication processes, such as using printing and coating techniques. Here, we demonstrate a sequential production protocol to fabricate supercapacitors including electrodes based on cellulose nanofibrils (CNF) and the conducting polymer PEDOT:PSS. Thin and lightweight paper electrodes, carbon adhesion layers and the gel electrolyte are fabricated using spray coating, screen printing, and bar coating, respectively. These all solid-state supercapacitors are flexible, mechanically robust and exhibit a low equivalent series resistance (0.22 Ω), thus resulting in a high power density (∼104 W/kg) energy technology. The supercapacitors are combined and connected to a power management circuit to demonstrate a smart packaging application. This work shows that operational and embedded supercapacitors can be manufactured in a manner to allow for the integration with, for instance smart packaging solutions, thus enabling powered, active internet-of-things (IoT) devices in a highly distributed application.

Transparent perovskite solar cells on paper Modified nanocellulose paper has been shown to be excellent biodegradable substrate for flexible perovskite solar cells and potentially other green flexible devices. A team of Chinese scientists led by Prof Wei Huang from Institute of Advanced Materials, Nanjing Tech University fabricate flexible perovskite solar cells on transparent nanocellulose paper. This becomes feasible only after they develop a treatment recipe to improve the mechanical, optical properties and the waterproof ability of the pure nanocellulose paper. The flexible solar cells on the modified substrates show high specific power of 0.56 W g-1 and good stability and mechanical durability. Another key advantage of nanocellulose paper is its biodegradation capability, making it a better substrate compared to PEN and PET for the next generation green flexible electronics.

In this paper, we demonstrate the current concepts in holographic tomography (HT) realized within limited angular range with illumination scanning. The presented solutions are based on the work performed at Warsaw University of Technology in Poland and put in context with the state of the art in HT. Along with the theoretical framework for HT, the optimum reconstruction process and data visualization are described in detail. The paper is concluded with the description of hardware configuration and the visualization of tomographic reconstruction, which is calculated using a provided processing path.

Glucose in saliva tested by paper sensors Saliva based glucose test can now be made easily and cheaply with inkjet-printed paper sensors enabled by enzyme glucose oxidase. Most present technologies rely on blood tests to monitor glucose concentration. To tackle this problem, a collaborative international team led by Prof Sahika Inal from King Abdullah University of Science and Technology, Saudi Arabia designs disposable glucose sensors based on saliva testing. They construct the analytical device by ink-jet printing cheap conducting polymer, an enzyme containing biological film and an encapsulation layer on paper substrates to measure glucose concentrations in human saliva. The devices stay active for more than a month in air-free storage conditions with minor performance losses. The high versatility and adaptability of the material system enable the possibilities to design affordable and expandable enzyme testing based diagnostic platforms.

Desktop printers and sprayers powering flexible electronics The power of commercial printers and spray coaters has been brought together to fasten the prototyping of flexible electronics. A collaborative team led by Prof Oana Jurchescu from Wake Forest University, US design an aerosol spray laser lithography approach to make patterned electrode arrays with low cost. The lithography step is realized by a desktop laser printer while the toner acts as the photoresist. The electrodes are deposited with spray coating of metal inks, followed by a heat-assisted transfer or peel-off process to finish the patterning. They then printed organic thin-film transistor arrays on paper and show that the devices work well under normal and bending conditions. This approach has proven successful, easy and compatible in fabricating flexible transistor arrays. It can be expected to fasten the pace in prototyping and manufacturing of flexible electronics.

It was found that the exposure to low-temperature gas discharge plasma at atmospheric pressure is an effective way of paper cleaning from fungal spores. This effect is explained by the specific mechanisms of micro-discharges excitation and maintaining that ensure efficient (up to 90 %) reduction in the number of viable mould spores without local heating biopolymeric materials.

Since Leith and Upatnieks demonstrated the first optical hologram in 1964, hologram technology has attracted a great deal of interest in a wide range of optical fields owing to its potential use in future optical applications such as holographic imaging and optical data storage. Although there have been considerable efforts to develop holographic technologies using conventional optics, critical issues still hinder future development. Recently, metasurfaces composed of artificially fabricated subwavelength structures have been considered as novel holographic devices that show an unprecedented ability to control electromagnetic waves. In this review, we outline the recent progress in metasurface holography. A general introduction to several types of metasurface holography categorized based on their physics and application is provided. Then, our personal perspective on the future of this field is discussed.

Ensembles of free standing particles of titanium, zinc, copper and iron oxides of 6-109 nm in size were sol-gel synthesized with a use of a cellulose paper as a template. The calcination time as short as 60 min at 550 °C in air was found to be sufficient for the formation of crystalline single phase TiO2 or ZnO nanoparticles, Cu2O+CuO or Fe2O3+Fe3O4 nanocomposites and to burn out the organic components. The impurities initially present in the cellulose (Сa, Na, Cl) were detected in the synthesized compounds. The original version of the paper was stolen by James Franklin and on-line published with the cut list of the authors in Journal of Nanomedicine and Nanotechnology 2017 without author permission.

Abstract Printing of electronics is pursued as a low-cost alternative to conventional manufacturing processes. In addition, owing to relatively low process temperatures, flexible substrates can be used enabling novel applications. Among flexible substrates, paper was found to be a particularly interesting candidate, since it has an order of magnitude lower price than low-cost polymer alternatives, and is biodegradable. As ink materials, organic and metal-oxide semiconductors are thoroughly being investigated; however, they lack in electric performance compared to silicon in terms of device mobility, reliability, and energy efficiency. In recent years, liquid precursors for silicon were found and used to create polycrystalline silicon (poly-Si). However, fabrication of transistors on top of low-cost flexible substrates such as paper has remained an outstanding challenge. Here we demonstrate both p-channel and n-channel poly-Si thin-film transistors (TFTs) fabricated directly on top of paper with field-effect mobilities of 6.2 and 2.0 cm2/V s, respectively. Many fabrication challenges have been overcome by limiting the maximum process temperature to approximately 100 °C, and avoiding liquid chemicals commonly used for etching and cleaning. Patterning of poly-Si has been achieved by additive selective crystallization of the precursor film using an excimer laser. This work serves as a proof of concept, and has the potential to further improve device performance. Owing to the low-cost, biodegradable nature of paper, and the high performance, reliability, and energy efficiency of poly-Si TFTs, this work opens a pathway toward truly low-cost, low-power, recyclable applications including smart packages, biodegradable health monitoring units, flexible displays, and disposable sensor nodes.