Search

The mechanical properties for paper sheets composited with glucose (Glc), methyl cellulose (MC), and carboxymethyl cellulose (CMC) were investigated. The paper composites were prepared by immersing paper sheets in aqueous solutions of these materials and drying at 100 °C for 30 min. The stress–strain curves for these paper composites were measured by a uniaxial tensile apparatus with a stretching speed of 2 mm/min. The breaking stress and strain for untreated paper were 24 MPa and 0.016, respectively. The paper composites demonstrated stress–strain curves similar to the untreated paper; however, the breaking point largely differed for these composites. The breaking strain and breaking stress for the Glc composite slightly decreased and those for the MC composite gradually increased with the concentration of materials composited. Significant increases in the mechanical properties were observed for the CMC composite. The breaking stress, breaking strain, and breaking energy for the 3 wt.% CMC composite were 2.0-, 3.9-, and 8.0-fold higher than those for untreated paper, respectively. SEM photographs indicated that the CMC penetrated into the inner part of the paper. These results strongly suggest that the mechanical improvement for CMC composites can be understood as an enhancement of the bond strength between the paper fibrils by CMC, which acts as a bonding agent. It was also revealed that the breaking strain, breaking stress, and breaking energy for the CMC composites were at maximum at the first cycle and decreased gradually as the immersion cycles increased.

A significant increase in the consumption of recycled fiber products has been observed worldwide, and the industry is forced to solve the challenges of recycled fiber quality and add strength agents and/or virgin fibers to reach sufficient properties. In order to investigate whether the mechanical and air permeability properties of waste fiber (WF) material can be significantly improved by adding wood kraft fibers (KF), hemp soda fibers (HF), and ammonium persulfate oxidated cellulose nanofibrils (CNF), different fiber blends were prepared and tested. Results revealed the excellence of hemp fibers over wood fibers regarding the improvement of WF products. The results of WF after the addition of 10% mixed fibers (KF + HF) were higher than the results of a 50% KF addition. The impact of CNF depended on fiber composition and properties. A formula for modeling the CNF impact on different fiber compositions was proposed. Obtained fiber material samples showed suitability for home composting, thus contributing to the goals of the European Green Deal regarding reducing landfill waste and the development of cleaner products.

Expansive soil exhibits significant swellings and shrinkages, which may result in severe damage or the collapse of structures built upon it. Calcium-based admixtures, such as lime, are commonly used to improve this problematic soil. However, traditional chemical additions can increase significant environmental stress. This paper proposes a sustainable solution, namely, the use of lignin fiber (LF) from the paper industry to partially replace lime as an amendment for expansive soils. Both the macroscopic and microscopic characteristics of the lignin fiber-treated expansive soil are extensively studied. The results show that the mechanical properties of expansive soil are improved by using lignin fiber alone. Under the condition of an optimal dosage of 8%, the compressive strength of lignin fiber-modified soil can reach 193 kPa, the shear strength is increased by 40% compared with the untreated soil, and the water conductivity is also improved with the increase in dosage. In addition, compared with 2% lime-modified soil, the compressive strength of 8% lignin fiber- and 2% lime composite-treated expansive soil increased by 50%, the cohesion increased by 12%, and the water conductivity decreased significantly. The microstructure analysis shows that at an 8% lignin fiber content, lignin fibers interweave into a network in the soil, which effectively enhances the strength and stability of the improved soil. Simultaneously, the fibers can form bridges across the adjacent micropores, leading to the merging of pores and transforming fine, dispersed micropores into larger, connected macropores. Lime promotes the flocculation of soil particles, forming larger aggregates and thus resulting in larger pores. The addition of fibers exerts an inhibitory effect on the flocculation reaction in the composite-improved soil. In conclusion, lignin fibers are an effective addition used to partially replace calcium admixture for the treatment of expansive soil, which provides a sustainable and environmentally friendly treatment scheme for reducing industrial waste.

The coefficient of friction for different contacting materials against skin is mainly influenced by the nature of the materials (synthetic and natural fabrics), mechanical contact parameters (interfacial pressure and sliding velocities), and physiological skin conditions (ambient humidity and skin moisture content). In the present research work, seven different types of papers used in everyday life were analyzed. The physical properties of these materials were determined through tensile tests and friction tests. By comparing mechanical properties with coefficient of friction, it was possible to conclude that the coefficient of friction is strongly correlated with the mechanical properties.

Paper-based friction material is a typical paper-based composite that is usually cured via hot-pressing. This curing method does not account for the effect of pressure on the matrix resin, resulting in uneven distribution of resin in the material and reducing the mechanical properties of friction materials. To overcome the above shortcomings, a pre-curing method was introduced before hot-pressing, and the effects of different pre-curing degrees on the surface morphology and mechanical properties of paper-based friction materials were studied. The pre-curing degree significantly affected the resin distribution and interfacial bonding strength of the paper-based friction material. When the material was cured at 160 °C for 10 min, the pre-curing degree reached 60%. At this point, most of the resin was in a gel state, which could retain abundant pore structures on the material surface without causing mechanical damage to the fiber and resin matrix during hot-pressing. Ultimately, the paper-based friction material exhibited improved static mechanical properties, decreased permanent deformation, and reasonable dynamic mechanical properties.

This review focuses on polymeric waste-paper composites, including state-of-the-art analysis with quantitative and qualitative discussions. Waste paper is a valuable cellulose-rich material, produced mainly from office paper, newspaper, and paper sludge, which can be recycled and returned to paper production or used in a new life cycle. A systematic literature review found 75 publications on this material over the last 27 years, with half of those published during the last five years. These data represent an increasing trend in the number of publications and citations that have shown an interest in this field. Most of them investigated the physicomechanical properties of composites using different contents of raw waste paper or the treated, modified, and cellulose-extracted types. The results show that polyethylene and polypropylene are the most used matrices, but polylactic acid, a biodegradable/sourced polymer, has the most citations. The scientific relevance of waste-paper composites as a subject includes the increasing trend of the number of publications and citations over the years, as well as the gaps identified by keyword mapping and the qualitative discussion of the papers. Therefore, biopolymers and biobased polymers could be investigated more, as well as novel applications. The environmental impact in terms of stability and degradation should also receive more attention regarding sustainability and life cycle analyses.

This study investigates the influence of fiber modification methods and beating degrees on the properties of paper sheets. Two different methods were used to modify fibers: NaOH + urea and TEMPO ((2,2,6,6-tetramethylpiperidin-1-yl)oxidanyl) and blended with traditional paper fibers. Subsequently, we evaluated the resulting sheets for their optical, strength, and thermo-mechanical characteristics. Notably, we also scrutinized sheets created exclusively with 100% TEMPO-modified fibers. The addition of modified fibers led to improvements in several strength properties, but it had a noteworthy negative impact on the optical properties of TEMPO-treated fibers compared to the other papers. Furthermore, thermal analysis revealed that the contraction rates of the samples increased considerably up to 40–50 °C for the out-of-plane direction and surpassed 130 °C for the in-plane direction. In general, the inclusion of modified fibers had a significant effect on thermo-mechanical properties. Specifically, TEMPO modification resulted in an increase in the maximum in-plane contraction ratio, shifting it from −0.40% to −0.59%, along with its corresponding temperature. This research underscores the potential of modified fibers to enhance paper properties and contribute to the development of more sustainable paper-based products.

Embossing is a functional and strategic process for creating high-quality multi-sensory tissue-paper products. Embossing modifies the sheet surface by generating hill and/or valley designs, changing the third-dimension z with a compressive die. This research work specifically concerns the impact study of the engraving finishing geometry on the final properties of tissue paper. This work led us to conclude that, even though the sheets individually present a higher hand-feel (HF) value for the straight finishing geometry, the highest softness was obtained in the two-ply prototype for the round finishing geometry. Moreover, this study confirmed that the HF value reduces with the increase of the bulk, being more accentuated for the micropattern. Relevant differences could not be seen in the spreading kinetics of the liquid droplets over time. Thus, the finishing geometry of the 3D plates did not impact the absorption kinetics on these samples. The finite element model allows us to understand the effect of the plate pattern and its finishing geometry on the paper, and the simulation results were in accordance with the experimental results, showing the same trend where patterns with a round finishing geometry marked the tissue-paper sheet more than patterns with a straight finishing did.

The paper tissue industry is a constantly evolving sector that supplies markets that require products with different specific properties. In order to meet the demand of functional properties, ensuring a green approach at the same time, research on bio-coatings has been very active in recent decades. The attention dedicated to research on functional properties has not been given to the study of the morphological and mechanical properties of the final products. This paper studied the effect of two representative bio-based coatings on paper tissue. Coatings based on chitin nanofibrils or polyphenols were sprayed on paper tissues to provide them, respectively, with antibacterial and antioxidant activity. The chemical structure of the obtained samples was preliminarily compared by ATR-FTIR before and after their application. Coatings were applied on paper tissues and, after drying, their homogeneity was investigated by ATR-FTIR on different surface areas. Antimicrobial and antioxidant properties were found for chitin nanofibrils- and polyphenols-treated paper tissues, respectively. The mechanical properties of treated and untreated paper tissues were studied, considering as a reference the same tissue paper sample treated only with water. Different mechanical tests were performed on tissues, including penetration, tensile, and tearing tests in two perpendicular directions, to consider the anisotropy of the produced tissues for industrial applications. The morphology of uncoated and coated paper tissues was analysed by field emission scanning electron microscopy. Results from mechanical properties evidenced a correlation between morphological and mechanical changes. The addition of polyphenols resulted in a reduction in mechanical resistance, while the addition of chitin enhanced this property. This study evidenced the different effects produced by two novel coatings on paper tissues for personal care in terms of properties and structure.

The potential use of paper sludge (PS) as filler in the production of bio-composites based on poly lactic acid (PLA) and polybutylene adipate terephthalate (PBAT) was investigated. PS/PLA/PBAT composites, with addition of acetyl tributyl citrate (ATBC) as biobased plasticizer, were produced with PS loadings up to 30 wt.% by twin-screw extrusion followed by injection moulding. The composites were characterized by rheological measurements, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and mechanical tests (tensile and impact resistance) to study the effect of PS on the processability, thermal stability, crystallinity and mechanical performance of polymeric matrix. The optimized composites at higher PS content were successfully processed to produce pots for horticulture and, in view of this application, preliminary phytotoxicity tests were conducted using the germination test on Lepidium sativum L. seeds. Results revealed that developed composites up to 30 wt.% PS had good processability by extrusion and injection moulding showing that PS is a potential substitute of calcium carbonate as filler in the production of bio-composites, and the absence of phytotoxic effects showed the possibility of their use in the production of pots/items for applications in floriculture and/or horticulture.

In this study, high-pressure laminates (HPL) impregnated with phenol-formaldehyde (PF) resins enriched with kraft lignin were developed. Pulverised kraft lignin was added to the commercial PF resin in the amounts of 1% and 5% (solid to solid). Laminates were manufactured using pressure impregnation of the resins into the papers and using hot pressing of HPL in a laboratory press. Laminates with a lignin content of 1% (L-LPF-1) showed the highest bending strength (72.42 MPa) and Brinell hardness (9.41); they also exhibited the best moisture uptake (9.61) and thickness swelling after immersion in water (3.32%). Except for impact bending, laminates with a lignin content of 5% (L-LPF-5) had worse properties. However, the differences between the variants are mostly not statistically significant and are comparable with the results of commercial PF resin. Scanning electron microscopy confirmed the homogenous structure of produced laminates and the occurrence of cohesive failures in ruptured L-LPF-1 laminates, whereas in ruptured L-LPF-5 laminates adhesive failures were also observed. Based on the conducted research it can be said that the utilisation of kraft lignin as an additive to PF resin (in the amount of 1%) has a positive effect on the produced HPL.

Different amounts of a stable aqueous TiO2 hydrosol were used to fabricate paper sheets having photocatalytic activity. The TiO2 hydrosol was prepared in aqueous medium using titanium butoxide as precursor and acetic acid as catalyst for the hydrolysis of titanium butoxide. An aging process at room temperature and atmospheric pressure was finally applied to obtain crystalline anatase TiO2 hydrosol. The effects of different TiO2 hydrosol loadings on the mechanical strength and barrier properties of modified paper sheets were investigated in detail. The photocatalytic behavior of TiO2-modified paper sheets was investigated as well using methylene blue (MB) as target pollutant.

When obtaining environment-friendly hybrid resins made of a blend of Dammar natural resin, in a prevailing volume ratio, with epoxy resin, it is challenging to find alternatives for synthetic resins. Composite materials reinforced with waste paper and matrix made of epoxy resin or hybrid resin with a volume ratio of 60%, 70% and 80% Dammar were studied. All samples obtained have been submitted to tensile tests and Scanning Electron Microscopy (SEM) analysis. The tensile response, tensile strength, modulus of elasticity, elongation at break and the analysis of the fracture surface were determined. The damping properties of vibrations of bars in hybrid resins and in the composite materials under study were also examined. The mechanical properties of the four types of resins and of the composite materials were compared. The chemical composition for a hybrid resin specimen were obtained using the Fourier Transformed Infrared Spectroscopy (FTIR) and Energy, Dispersive X-ray Spectrometry (EDS) analyzes.

Ceramic matrix composites (CMCs) based on silicon carbide (SiC) are promising materials for applications as structural components used under high irradiation flux and high temperature conditions. The addition of SiC fibers (SiCf) may improve both the physical and mechanical properties of CMCs and lead to an increase in their tolerance to failure. This work describes the fabrication and characterization of novel preceramic paper-derived SiCf/SiCp composites fabricated by spark plasma sintering (SPS). The sintering temperature and pressure were 2100 °C and 20−60 MPa, respectively. The content of fibers in the composites was approx. 10 wt.%. The matrix densification and fiber distribution were examined by X-ray computed tomography and scanning electron microscopy. Short processing time avoided the destruction of SiC fibers during SPS. The flexural strength of the fabricated SiCf/SiCp composites at room temperature varies between 300 and 430 MPa depending on the processing parameters and microstructure of the fabricated composites. A quasi-ductile fracture behavior of the fabricated composites was observed.

Embossing is a converting process in which the surface of a tissue paper sheet is changed under high pressure, allowing different functions. In this work, the authors intend to study how the embossing pressure affects the main properties of tissue paper, using a laboratory embossing system. An optimum pressure was achieved at 2.8 bar to this embossing laboratory set-up. The effect of pressure when densifying the paper sheet gives it a gain in mechanical strength but no differences in terms of liquid absorbency. The two embossing patterns present different behaviors but both evidence losses in mechanical and softness properties. On the other hand, the finite element method (FEM) does not show clear evidence of how the pressure affects the paper strength. For the deco die, it is possible to observe that the amount of yielding is slightly higher for lower pressure (2.4 bar), but this plasticity state parameter is very similar for 2.8 bar and 3.2 bar. For the micro die, FEM simulations of the manufacturing pressure do not show a considerable impact on the amount of plasticity state of the material; only for 3.2 bar, it shows a change in the pattern of the plasticity state of the paper during the embossing processes. In the end, to achieve a final product with excellent quality, it is important to make a compromise between the various properties.

The embossing operation is one of the processes of tissue paper converting. The embossing parameters influence the final properties of tissue products, such as mechanical, softness, and bulk. In this study, the influence of the rubber hardness used against the embossing steel rolls with a pattern created by intaglio engraving was studied. Three different configurations of rubber plates stacking, each plate with different hardness, were studied. After embossing, mechanical properties, softness, and bulk were evaluated to analyze the effect of rubbers hardness on these properties. Furthermore, a Finite Element Model of the embossing operation was used that considered the same rubber plates stacking configurations used in experiments, and it was able to replicate the experimental results. This work led us to conclude that the configuration where two rubber plates with different hardness, where the rubber plate with higher hardness is in contact with the tissue paper sheet, has shown to be the best solution to obtain higher softness. These findings support the use of embossing operations rubber rolls with a low hardness internal layer and a high hardness external layer in industry. Thus, finite element models were also shown to be reliable tools to virtually test other configurations, such as, for example, three or more rubber plates with different hardness. Since embossing is one of the tissue paper transformation operations with the greatest impact on the key properties of the final product, this study allows the producer to optimize them by varying the hardness of the rubber roll, as well as its configuration.

The recycled paper and board industry needs to improve the quality of their products to meet customer demands. The refining process and strength additives are commonly used to increase mechanical properties. Interfiber bonding can also be improved using cellulose nanofibers (CNF). A circular economy approach in the industrial implementation of CNF can be addressed through the in situ production of CNF using side cellulose streams of the process as raw material, avoiding transportation costs and reducing industrial wastes. Furthermore, CNF fit for use can be produced for specific industrial applications.This study evaluates the feasibility of using two types of recycled fibers, simulating the broke streams of two paper machines producing newsprint and liner for cartonboard, to produce in situ CNF for direct application on the original pulps, old newsprint (ONP), and old corrugated container (OCC), and to reinforce the final products. The CNF were obtained by 2,2,6,6-tetramethyl-1-piperidinyloxy (TEMPO)-mediated oxidation and homogenization at 600 bar. Handsheets were prepared with disintegrated recycled pulp and different amounts of CNF using a conventional three-component retention system. Results show that 3 wt.% of CNF produced with 10 mmol of NaClO per gram of dry pulp improve tensile index of ONP ~30%. For OCC, the same treatment and CNF dose increase tensile index above 60%. In both cases, CNF cause a deterioration of drainage, but this effect is effectively counteracted by optimising the retention system.

The goal of this study was to analyze the effects of cellulose fibers loading by precipitation in-situ of calcium carbonate over the properties of printing paper obtained from mixtures of the softwood and hardwood fibers. The effects of fibers with in-situ loading were analyzed comparatively with conventional paper loading respectively, by adding precipitated calcium carbonate into fiber stock. The effectiveness of the methods was evaluated by various analyses and investigations: calcium carbonate content, Scanning electron microscope (SEM) images, X-ray diffraction, optical and mechanical properties of the paper sheets. The evaluation of the effects on paper properties led to the conclusion that, at the same filler content, the in-situ loading method gives higher opacity and brightness than conventional methods. The utilization of cellulose fibers with in-situ loading as additive, shown as a modification of the ratio between fibers with in-situ loading and fibers without loading, regardless of whether they are softwood or hardwood fibers, allowed us to optimize printing paper properties, especially regarding the relationship between optical and strength properties.

Polymethylsilsesquioxane (PMSQ) nanoparticles with mass percentages of 0, 2.5, 5.0, 7.2, 9.4 wt %, respectively, were constructed by molecular dynamics methods in this paper. Composite molecular models were established using PMSQ and MPIA (poly-metaphenylene isophthalamide) fiber. The influence of different PMSQ contents on the thermal stability of meta-aramid insulation paper was analyzed from the parameters of mechanical property, interaction energy, and mean square displacement. The results showed that the trend of mechanical properties decreased with the increase of PMSQ content. When the PMSQ content was 2.5 wt %, the mechanical properties of the composited model were the best, which was about 24% higher than that of the unmodified model. From an intermolecular bonding and nonbonding point of view, the energy parameters of composite model with the 2.5 wt % content was better than those of the composite model with other contents. Therefore, it is considered that MPIA can interact better with the 2.5 wt % content PMSQ composite model. When the PMSQ content is 2.5 wt %, the overall chain movement in the composite model is slower than that of the unmodified model, which can effectively inhibit the diffusion movement of the MPIA chain. In general, the thermal stability of composite molecular models MPIA and PMSQ (2.5 wt %) was better improved.

The aim of the study was to isolate lignin from organosolv, beech tree (Fagus sylvatica), and Japanese knotweed (Reynoutria japonica), to use it for paper surface and to replace part of the non-renewable product resources with bio-based ones. A total of nine coated samples with different lignin formulations and starch were compounded, prepared, and evaluated. The basic (grammage, thickness, specific density), mechanical (elongation at break, tensile, burst and tear indices), and barrier properties (contact angle, water penetration, water vapour permeability, kit test) of the coated papers were investigated. The analysis showed no significant difference in tensile properties between uncoated and coated samples. Furthermore, the decrease in water vapour transmission rate and the lower contact angle for coated samples were nevertheless confirmed. The novel coating materials show promising products with very good barrier properties. Finally, the correlation between structural, morphological, and (other) natural lignin-based factors was revealed, highlighting the importance of parameters such as the equivalence ratio of aliphatic and phenolic hydroxyl groups or the average molecular weight. Tuning functionality by design could optimise performance in the future.

The accelerated ageing of wood in terms of heating or iron rusting has a potential effect on the physio-mechanical, chemical and biological properties of wood. The effects of accelerated ageing on the mechanical, physical and fungal activity properties of some wood materials (Schinus terebinthifolius, Erythrina humeana, Tectona grandis, Pinus rigida and Juglans nigra) were studied after several cycles of heating and iron rusting. The fungal activity was assayed against the growth of Aspergillus terreus, Aspergillus niger, Fusarium culmorum and Stemphylium solani. In addition, the mechanical and optical properties of paper sheets produced from those wood pulps by means of Kraft cooking were evaluated. The mechanical and chemical properties of the studied wood species were affected significantly (p < 0.05) by the accelerated ageing, compared to control woods. With Fourier transform infrared (FTIR) spectroscopy, we detected an increase in the intensity of the spectra of the functional groups of cellulose in the heated samples, which indicates an increase in cellulose content and decrease in lignin content, compared to other chemical compounds. For pulp properties, woods treated by heating showed a decrease in the pulp yield. The highest significant values of tensile strength were observed in pulp paper produced from untreated, heated and iron-rusted P. rigida wood and they were 69.66, 65.66 and 68.33 N·m/g, respectively; we calculated the tear resistance from pulp paper of untreated P. rigida (8.68 mN·m2/g) and T. grandis (7.83 mN·m2/g) and rusted P. rigida (7.56 mN·m2/g) wood; we obtained the values of the burst strength of the pulp paper of untreated woods of P. rigida (8.19 kPa·m2/g) and T. grandis (7.49 kPa·m2/g), as well as the fold number of the pulp paper of untreated, heated and rusted woods from P. rigida, with values of 195.66, 186.33 and 185.66, respectively. After 14 days from the incubation, no fungal inhibition zones were observed. Accelerated ageing (heated or iron-rusted) produced significant effects on the mechanical and chemical properties of the studied wood species and affected the properties of the produced pulp paper.

The mechanical loads that gas diffusion layers (GDLs) withstand in polymer electrolyte membrane fuel cell (PEMFC) stacks are sensitive to the assembly and working conditions. The mechanical properties of GDLs mostly depend on their composition materials, microstructural characteristics, operation conditions, etc. An accurate and comprehensive understanding of the mechanical performance of GDLs is significant for predicting the stress distribution and improving the assembly technology of PEMFC stacks. This study presented a novel 3-D nonlinear and orthotropic constitutive model of a carbon paper GDL to represent the material stiffness matrix with its compressive, tensile, and shear properties. Numerical simulations were performed based on the 3-D constitutive model, and the proposed 3-D model was validated against the experimental data reported previously. It is found that the simulation results of the 3-D constitutive model show a good agreement with the experimental results. Besides, the novel 3-D nonlinear and orthotropic model was applied in the overall stress simulation of a simplified PEMFC unit cell, compared to a conventional 3-D linear and isotropic model, and the simulation results of the two models show a significant difference.

Hybrid nanomaterials fabricated by the heterogeneous integration of 1D (carbon nanotubes) and 2D (graphene oxide) nanomaterials showed synergy in electrical and mechanical properties. Here, we reported the infiltration of carboxylic functionalized single-walled carbon nanotubes (C-SWNT) into free-standing graphene oxide (GO) paper for better electrical and mechanical properties than native GO. The stacking arrangement of GO sheets and its alteration in the presence of C-SWNT were comprehensively explored through scanning electron microscopy, X-ray photoelectron spectroscopy (XPS) and X-ray diffraction. The C-SWNTs bridges between different GO sheets produce a pathway for the flow of electrical charges and provide a tougher hybrid system. The nanoscopic surface potential map reveals a higher work function of the individual functionalised SWNTs than surrounded GO sheets showing efficient charge exchange. We observed the enhanced conductivity up to 50 times and capacitance up to 3.5 times of the hybrid structure than the GO-paper. The laminate of polystyrene composites provided higher elastic modulus and mechanical strength when hybrid paper is used, thus paving the way for the exploitation of hybrid filler formulation in designing polymer composites.

In the present paper, aspects concerning the obtained and characterization of additive systems used for maximizing filler retention, and the effects on paper properties, were investigated. The effects of retention additives over properties of paper, containing fibers from in-situ loading (IS-CCP), were analyzed against the effects of additives over properties of paper containing fibers from conventional loading, obtained by the addition of calcium carbonate in precipitated form (CCP). The physico-mechanical properties were analyzed by various analyses and investigations: calcium carbonate content, X-ray diffraction, scanning electron microscopy (SEM) images, optical and mechanical properties, in order to develop the best systems of retention additives for obtaining higher retention loads for making paper with high content of nano-filler material. The obtained results reveal that at the same level of calcium carbonate content, all paper samples with in-situ loading had higher the optical and mechanical properties than the paper obtained by conventional loading in all cases the additives studied. For all studied properties, nanoparticles had a positively influence over paper properties.

A new type of reinforcement for unidirectional natural fiber composites has been developed, where a paper layer is assembled with a layer of unidirectional flax yarns. The paper layer chemically and mechanically bonds to the loose yarns to maintain their alignment and enables better manipulability of the reinforcement during stacking in the mold. Unfortunately, the paper layer adversely affects the permeability of the whole reinforcement to liquid resin and thus limits the impregnation quality of the final part. In this paper, a technique is adopted to increase the impregnation performance by modifying the architecture of the fibrous network in the paper layer. In particular, a method has been developed to replace a proportion of the Kraft fibers by short flax fibers in the paper layer, in an attempt to open the structure and increase the paper permeability. Permeability measurements show a major improvement in global reinforcement permeability. Basic mechanical properties of resulting composites were also analysed. Results show a slight decrease in modulus and strength when the paper layer is present. This is compensated by an important reduction in variability. Furthermore, increasing the flax proportion in the paper layer limits the loss of mechanical properties, while reducing variability even further.

This manuscript presents a comprehensive literature review with the aim to provide readers a reference document with up-to-date information on the field of methanol use as a chemical marker. It has been a little more than a decade since methanol was first introduced as a marker for assessing solid insulation condition in power transformers. It all started when methanol was identified in the laboratory during thermal ageing tests carried out with oil-immersed insulating papers and was subsequently also identified in transformer field samples. The first publication on the subject was released in 2007 by our research group. This review covers the methanol fundamentals such as the analytical methods for its determination in transformer oil, which is generally performed by headspace gas chromatography with mass spectrometry or flame ionization as a detector. Current standardization efforts for its determination include ASTM working group 30948 and IEC TC10. Kinetic studies have confirmed the relationship between methanol generation, the number of broken 1,4-β-glycosidic bonds of cellulose and changes in mechanical properties. Laboratory tests have confirmed its stability at different accelerated ageing temperatures. Several utilities have identified methanol during field measurements, case studies on power and some distribution transformers are presented, as well as transformer postmortem investigations. These field-testing results demonstrate its utility in monitoring cellulosic insulation degradation. Recently, a model of methanol interpretation has become available that allows for evaluation of the average degree of polymerization of core type transformer cellulose winding. Methanol has a role as an indicator of cellulosic solid insulation ageing in transformer mineral oil, and it is expected that in the future it will be in routine use by utilities.

Paper fibers have gained broad attention in natural fiber reinforced composites in recent years. The specific problem in preparing paper fiber reinforced composites is that paper fibers easily become flocculent after pulverization, which increases difficulties during melt-compounding with polymer matrix and results in non-uniform dispersion of paper fibers in the matrix. In this study, old newspaper (ONP) was treated with a low dosage of gaseous methyltrichlorosilane (MTCS) to solve the flocculation. The modified ONP fibers were characterized by Scanning Electron Microscope (SEM), Fourier Transform Infrared Spectroscopy (FTIR), and Thermogravimetric Analysis (TG). Then the modified ONP fibers and high-density polyethylene (HDPE) were extruded and pelletized to prepare ONP/HDPE composites via injection molding. Maleic anhydride-grafted polyethylene (MAPE) was added to enhance the interfacial bonding performance with the ultimate purpose of improving the mechanical strength of the composites. The mechanical properties such as tensile, flexural, and impact strength and the water absorption properties of the composite were tested. The results showed that the formation of hydrogen bonding between ONP fibers was effectively prevented after MTCS treatment due to the reduction of exposed −OH groups at the fiber surface. Excessive dosage of MTCS led to severe fiber degradation and dramatically reduced the aspect ratio of ONP fibers. Composites prepared with ONP fibers modified with 4% (v/w) MTCS showed the best mechanical properties due to reduced polarity between the fibers and the matrix, and the relatively long aspect ratio of treated ONP fibers. The composite with or without MAPE showed satisfactory water resistance properties. MTCS was proven to be a cheap and efficient way to pretreat old newspaper for preparing paper fiber reinforced composites.

In the last decade, iron and magnesium, both pure and alloyed, have been extensively studied as potential biodegradable metals for medical applications. However, broad experience with these material systems has uncovered critical limitations in terms of their suitability for clinical applications. Recently, zinc and zinc-based alloys have been proposed as new additions to the list of degradable metals and as promising alternatives to magnesium and iron. The main byproduct of zinc metal corrosion, Zn2+, is highly regulated within physiological systems and plays a critical role in numerous fundamental cellular processes. Zn2+ released from an implant may suppress harmful smooth muscle cells and restenosis in arteries, while stimulating beneficial osteogenesis in bone. An important limitation of pure zinc as a potential biodegradable structural support, however, lies in its low strength (σUTS ~ 30 MPa) and plasticity (ε < 0.25%) that are insufficient for most medical device applications. Developing high strength and ductility zinc with sufficient hardness, while retaining its biocompatibility, is one of the main goals of metallurgical engineering. This paper will review and compare the biocompatibility, corrosion behavior and mechanical properties of pure zinc, as well as currently researched zinc alloys.

The first part of this paper is dedicated to obtaining 3D-printed molds using poly lactic acid (PLA) incorporating specific patterns, which have the potential to serve as the foundation for sound-absorbing panels for various industries and aviation. The molding production process was utilized to create all-natural environmentally friendly composites. These composites mainly comprise paper, beeswax, and fir resin, including automotive function as the matrices and binders. In addition, fillers, such as fir needles, rice flour, and Equisetum arvense (horsetail) powder, were added in varying amounts to achieve the desired properties. The mechanical properties of the resulting green composites, including impact and compressive strength, as well as maximum bending force value, were evaluated. The morphology and internal structure of the fractured samples were analyzed using scanning electron microscopy (SEM) and an optical microscopy. The highest impact strength was measured for the composites with beeswax, fir needles, recyclable paper, and beeswax fir resin and recyclable paper, 19.42 and 19.32 kJ/m2, respectively, while the highest compressive strength was 4 MPa for the beeswax and horsetail-based green composite. Natural-material-based composites exhibited 60% higher mechanical performance compared to similar commercial products used in the automotive industry.

This review presents the research conducted to date in the field of cement-based composites reinforced with waste paper-based cellulose fibres, focusing on their composition, mechanical properties, and durability characteristics. The literature demonstrates that the properties of raw material (depending on their own chemical composition) significantly influence the formation of the cement composite binders. When considering fresh properties, the presence of silica and magnesium compounds generally lead to favourable effects on the setting of the cement composite when combined with waste paper cellulose fibre. Reduction in density values, i.e., approximately 25%, was observed with the inclusion of waste paper fibres from 20 to 80% in cement composites. The homogeneous dispersion of fibres in the matrix is one of the crucial factors to achieve in order to develop composites with well-balanced mechanical properties incorporating waste paper cellulose fibres. Hence, dispersion of fibres can be improved by increasing water quantity corresponding to the optimal value, which was a water/cement ratio of 0.64 leading to optimum strength properties of the composite. Even though the effect of fibre dispersion in the matrix improves with the addition of water, higher porosity and voids govern the strength properties beyond an optimum water-to-cement ratio. Higher porosity leads to an increase in the water absorption and a lowering of the thermal conductivity properties with the addition of paper fibre in cement binders. Paper fibre absorbs a high amount of water leading to higher water absorption. This phenomenon is related to the hydrophilic nature of cellulosic fibres absorbing some volume of water due to their microporous structure.

Waste ceramic is produced from different sources and, if not reused, is often disposed of in landfills, contributing to the pressure on landfill capacity and potentially releasing toxins into the surrounding environment as ceramics break down over time. The waste can easily be crushed to the required sizes, which has interested many researchers. It has been used as a replacement for concrete constituents, including cement and aggregates. This offers a promising avenue for reducing the environmental impact and promoting sustainable construction practices by reducing the amount of energy consumed and resources required for concrete production, as well as the amount of waste being sent to landfills. This paper aims to provide a review of the use of waste ceramic in concrete. In essence, the paper is divided into several sections. The first section highlights the current environmental issues associated with concrete production and waste disposal. The second section deals with ceramics, its raw materials, production steps, and the different types of waste ceramic used in concrete. A literature review of the use of waste ceramic in concrete was included in the third section. The study reports different research on the use of waste ceramic and its impacts on the mechanical and durability properties of concrete.

Due to the large increase in human population, the need for more buildings and other amenities is widening. Concrete is considered one of the most abundant and popular materials used in the structure and construction fields. It is known as a composite mix composed of cement and aggregates including fine and coarse and water. Despite its good properties, its capability to be formed in different shapes and its ability to resist severe conditions, concrete will struggle with the presence of extremely high temperatures. So, different types of concrete must be found to resist those challenging conditions. Refractory concrete can be considered a good choice to be used in places exposed to elevated temperatures and severe conditions. Mainly, refractory concrete is made up of ordinary Portland cement replacement well known as refractory cement, specific types of fine and coarse aggregates and are known as refractory or temperature-bearing aggregates and water. To the best authors’ knowledge, review papers about refractory concrete are rare. For this reason, more than 65 papers were consulted including many recently published. This review describes the different types of materials used in refractory concrete. Furthermore, the different fresh, hardened, structural, durability and thermal properties of refractory concrete are also included such as slump, density, compressive strength, flexural strength, tensile strength, modulus of elasticity, ultrasonic pulse velocity, shrinkage, mass loss, porosity, water absorption, damage level and thermal conductivity.

Before artificial ageing, extruded aluminium profiles are subjected to stretching with a small cold deformation in the range of 0.5–2%. This deformation improves the geometrical stability of the extruded product and causes changes in the microstructure of the profile, which leads to the strain hardening of the material after artificial ageing. The work has resulted in the creation of the prototype of an original device, which is unique in the world, for the dynamic stretching of the extruded profiles after quenching. The semi-industrial unit is equipped with a hydraulic system for stretching and a pneumatic system for cold dynamic deformation. The aim of this research paper is to produce advantageous microstructural changes and increase the strength properties of the extruded material. The solution of the dynamic stretching of the profiles after extrusion is a great challenge and an innovation not yet practised. The paper presents the results of microstructural and mechanical investigations carried out on extruded AlMgSi(Cu) alloys quenched on the run-out table of the press, dynamically stretched under different conditions, and artificially aged for T5 temper. Different stretching conditions were applied: a static deformation of 0.5% at a speed of 0.02 m/s, and dynamic deformation of 0.25%, 0.5%, 1%, and 1.5% at speeds of 0.05 and 2 m/s. After the thermomechanical treatment of the profiles, microstructural observations were carried out using an optical microscope (OM) and a scanning electron microscope (SEM). A tensile test was also carried out on the specimens stretched under different conditions. In all the cases, the dynamically stretched profiles showed higher strength properties, especially those deformed at a higher speed of 2 m/s, where the increase in UTS was observed in the range of 7–18% compared to the classical (static) stretching. The microstructure of the dynamically stretched profiles is more homogeneous with a high proportion of fine dispersoids.