Search

Brittleness in paper is one of the primary reasons library books are removed from circulation, digitized, or have their access limited. Yet, paper brittleness is difficult to characterize as it has multiple definitions and no single measurable physical or chemical property associated with it. This study reevaluates the cantilever test as applied to aged papers. In this nondestructive test, the deflection of a strip of paper held horizontally is measured across its length. The deflection data are then fit to nonlinear bending theories assuming large deflection of a cantilever beam under a combined uniform and concentrated load. Fitting the shape of the deflection profiles provides bending and elastic moduli, the bending length, and confirms that the paper sheets respond linearly. The results are compared to those calculated from a simplified single point measurement of the maximum deflection of the cantilevered sample. Young's modulus measured by the cantilever test is lower for paper-based materials than that measured by tensile testing, and the bending modulus was found to correlate with the destructive Massachusetts Institute of Technology (MIT) fold endurance test. [ABSTRACT FROM AUTHOR]

The manufacture of low density paper such as tissue and towel utilizes the creping process that consists of adhesively bonding the paper in wet state onto the surface of a smooth drying cylinder and scraping it off with a blade once dried. In this paper, a mechanics of materials description of the creping process is presented. Based upon previous experimental observations, the mechanism of this creping process is proposed as a periodic debonding with a strength-of-materials failure criterion applied and buckling sequence of an elastic thin film. Numerical calculations show results consistent with experimental data and known industrial observations. Crepe wavelength versus creping angle data from experiments can be satisfactorily reproduced by a reasonable set of values for input parameters to the model. Parametric study shows the adhesive shear strength and the sheet stiffness most significantly affect the crepe wavelength and the creping force. The model provides guidance in understanding and optimizing the creping process to produce high quality products. [ABSTRACT FROM AUTHOR]

Rolls of films and paper are routinely stored under varying conditions before being unwound into downstream operations. During storage, interlayer pressures can change relative to the pressures generated during winding. These changes can lead to problems such as film/paper blocking (increased interlayer pressure) and roll shifting/cinching (decreased interlayer pressure). To study the storage effect, a nonlinear wound roll stress model including air entrainment is first developed and applied to predict the in-roll stresses during film/paper winding. Thereafter, a thermal stress model is used to study the temperature effect on wound roll stresses. Key inputs to the models are the stack modulus, contact clearance, and air film reference clearance. A method is developed to measure these key model inputs. Results of a parametric study show that among the processing conditions, storage temperature and thermal expansion coefficients of the core and the film/paper are key factors that affect in-roll stresses during storage. Limitations of the models will also be discussed along with recommendations for future modeling development. [ABSTRACT FROM AUTHOR]

Presents information on a study which analyzed the heating and drying process of moist paper with infrared radiation energy. Set-up of the experiment; Description of paper samples; Error and theoretical analyses; Results of the study; Comparison of numerical and experimental results.

Part II. Presents a study which analyzed the flutter phenomena of flexible thin sheets such as paper swept by wind for a range of mass ratios. Method; Results; Conclusion.

This paper presents a conceptually simple and resource efficient method for robust parameter design. The proposed method varies control factors according to an adaptive one-factor-at-a-time plan while varying noise factors using a two-level resolution III fractional factorial array. This method is compared with crossed arrays by analyzing a set of four case studies to which both approaches were applied. The proposed method improves system robustness effectively, attaining more than 80% of the potential improvement on average if experimental error is low. This figure improves to about 90% if prior knowledge of the system is used to define a promising starting point for the search. The results vary across the case studies, but, in general, both the average amount of improvement and the consistency of the results are better than those provided by crossed arrays if experimental error is low or if the system contains some large interactions involving two or more control factors. This is true despite the fact that the proposed method generally uses fewer experiments than crossed arrays. The case studies reveal that the proposed method provides these benefits by exploiting, with high probability, both control by noise interactions and also higher order effects involving two control factors and a noise factor. The overall conclusion is that adaptive one-factor-at-a-time, used in concert with factorial outer arrays, is demonstrated to be an effective approach to robust parameter design providing significant practical advantages as compared to commonly used alternatives. [ABSTRACT FROM AUTHOR]