Search

A simple approach to the mass production of nanoporous gold electrode arrays on cellulose membranes for electrochemical sensing of oxygen using ionic liquid (IL) electrolytes was established. The approach, combining the inkjet printing of gold nanoparticle (GNP) patterns with the self-catalytic growth of these patterns into conducting layers, can fabricate hundreds of self-designed gold arrays on cellulose membranes within several hours using an inexpensive inkjet printer. The resulting paper-based gold electrode arrays (PGEAs) had several unique properties as thin-film sensor platforms, including good conductivity, excellent flexibility, high integration, and low cost. The porous nature of PGEAs also allowed the addition of electrolytes from the back cellulose membrane side and controllably produced large three-phase electrolyte/electrode/gas interfaces at the front electrode side. A novel paper-based solid-state electrochemical oxygen (O(2)) sensor was therefore developed using an IL electrolyte, 1-butyl-3-methylimidazolium hexafluorophosphate (BMIMPF(6)). The sensor looked like a piece of paper but possessed high sensitivity for O(2) in a linear range from 0.054 to 0.177 v/v %, along with a low detection limit of 0.0075% and a short response time of less than 10 s, foreseeing its promising applications in developing cost-effective and environment-friendly paper-based electrochemical gas sensors.

Lignocellulosic biomass offers economic and environmental advantages over corn starch for biofuels production. However, its fractionation currently requires energy-intensive pretreatments, due to the lignin chemical resistance and complex cell wall structure. Recently, ionic liquids have been used to dissolve biomass at high temperatures. In this study, thin sections of poplar wood were swollen by ionic liquid (1-ethyl-3-methylimidazolium acetate) pretreatment at room temperature. The samples contract when rinsed with deionized water. The controlled expansion and contraction of the wood structure can be used to incorporate enzymes and catalysts deep into the wood structure for improved pretreatments and accelerated cellulose hydrolysis. As a proof of concept, silver and gold nanoparticles of diameters ranging from 20 to 100 nm were incorporated at depths up to 4 mum. Confocal surface-enhanced Raman images at different depths show that a significant number of nanoparticles were incorporated into the pretreated sample, and they remained on the samples after rinsing. Quantitative X-ray fluorescence microanalyses indicate that the majority of nanoparticle incorporation occurs after an ionic liquid pretreatment of less than 1 h. In addition to improved pretreatments, the incorporation of materials and chemicals into wood and paper products enables isotope tracing, development of new sensing, and imaging capabilities.

A paper-based solid-phase assay is presented for transduction of nucleic acid hybridization using immobilized quantum dots (QDs) as donors in fluorescence resonance energy transfer (FRET). The surface of paper was modified with imidazole groups to immobilize QD-probe oligonucleotide conjugates that were assembled in solution. Green-emitting QDs (gQDs) were FRET-paired with Cy3 acceptor. Hybridization of Cy3-labeled oligonucleotide targets provided the proximity required for FRET-sensitized emission from Cy3, which served as an analytical signal. The assay exhibited rapid transduction of nucleic acid hybridization within minutes. Without any amplification steps, the limit of detection of the assay was found to be 300 fmol with the upper limit of the dynamic range at 5 pmol. The implementation of glutathione-coated QDs for the development of nucleic acid hybridization assay integrated on a paper-based platform exhibited excellent resistance to nonspecific adsorption of oligonucleotides and showed no reduction in the performance of the assay in the presence of large quantities of noncomplementary DNA. The selectivity of nucleic acid hybridization was demonstrated by single-nucleotide polymorphism (SNP) detection at a contrast ratio of 19 to 1. The reuse of paper over multiple cycles of hybridization and dehybridization was possible, with less than 20% reduction in the performance of the assay in five cycles. This work provides an important framework for the development of paper-based solid-phase QD-FRET nucleic acid hybridization assays that make use of a ratiometric approach for detection and analysis. [ABSTRACT FROM AUTHOR]

Reversible protein phosphorylation on serine, threonine, and tyrosine residues is essential for fast, specific, and accurate signal transduction in cells. Up to now, the identification and quantification of phosphorylated amino acids, peptides, and proteins continue to be one of the significant challenges in contemporary bioanalytical research. In this paper, a series of surface grafted monoliths in the capillary format targeting phosphorylated serine has been prepared by first synthesizing a monolithic core substrate material based on trimethylolpropane trimethacrylate, onto which a thin surface-imprinted layer was established by oriented photografting of a variety of mono- and bis- imidazolium host monomers at subzero temperature, using six different continuous or pulsed UV light sources. The imprinted monolith capillaries were evaluated in a capillary liquid chromatographic system connected to a mass spectrometer in order to test the specific retention of phosphorylated peptides. Site-specific recognition selectivity and specificity for phosphorylated serine was demonstrated when separating amino acids and peptides, proving that the optimized materials could be used as novel trapping media in affinity-based phosphoproteomic analysis.

Ionic liquids (ILs) are ionic compounds with low melting points that can be designed to be used in an extensive set of commercial and industrial applications. However, the design of ILs is limited by the quantity and quality of the available data in the literature; therefore, the estimation of physicochemical properties of ILs by computational methods is a promising way of solving this problem, since it provides approximations of the real values, resulting in savings in both time and money. We studied two data sets of 281 and 134 liquids based on the molecule imidazole that were analyzed with QSPR techniques. This paper presents a software architecture that uses clustering techniques to improve the robustness of estimation models of the melting point of ILs. These results indicate an error of 6.25% in the previously unmodeled data set and an error of 4.43% in the second data set. We have an improvement with the second data set of 1.81% over the last results previously found.

An efficient large-scale synthesis of acid 1, a penultimate precursor to the HCV NS5A inhibitor BMS-986097, along with the final API step are described. Three routes were devised for the synthesis of 1 at the various stages of the program. The third generation route, the one that proved scalable and is the main subject of this paper, features a one-step Michael addition of t-butyl 2-((diphenylmethylene)amino)acetate (24) to (E)-benzyl 4-(1-hydroxycyclopropyl)but-2-enoate (28) followed by cyclization and chiral separation to form 27c, the core skeleton of cap piece 1. The epimerization and chiral resolution of 27c followed by further synthetic manipulations involving the carbamate formation, lactone reduction and cyclization, afforded cyclopropyl pyran 1. A detailed study of diphenylmethane deprotection via acid hydrolysis as well as a key lactone to tetrahydropyran conversion, in order to avoid a side reaction that afforded an alternative cyclization product, are discussed. This synthesis was applied to the preparation of more than 100 g of the final API BMS-986097 for toxicology studies.

This paper describes the design and synthesis of a conjugate (Q7R) comprising the synthetic host cucurbit[7]uril (Q7) linked to the fluorescent dye tetramethylrhodamine (TMR), and the characterization of its optical and guest-binding properties as well as its cellular uptake. Q7R was synthesized in two steps from monofunctionalized azidobutyl-Q7 and NHS-activated TMR. The fluorescence of Q7R is quenched upon guest binding, and this observable was used to determine equilibrium dissociation constant (K d ) values. Unexpectedly, the K d values for guests binding to Q7R and to unmodified Q7 were essentially identical. Therefore, Q7R can directly report binding to Q7 without an energetic penalty due to the conjugated fluorophore. This result demonstrates a potentially general strategy for the design of single-component host-indicator conjugates that respond sensitively to analytes without perturbing the binding properties of the host. The unique properties of Q7R enabled measurement of K d values across 3 orders of magnitude and at concentrations as low as 0.7 nM. This result is particularly relevant given the unmatched range of guests and binding affinities demonstrated for Q7. Confocal fluorescence microscopy of live and fixed HT22 neurons revealed the cellular uptake of Q7R and its punctate localization in the cytoplasm. Q7R did not alter cell growth at concentrations up to 2.2 μM over 4 days. These experiments demonstrate the feasibility of Q7R as a direct sensor for guest binding and as a cell-permeable compound for imaging applications.

The work in this paper describes the optimization of the 3-(3-phenyl-3H-imidazo[4,5-b]pyridin-2-yl)pyridin-2-amine chemical series as potent, selective allosteric inhibitors of AKT kinases, leading to the discovery of ARQ 092 (21a). The cocrystal structure of compound 21a bound to full-length AKT1 confirmed the allosteric mode of inhibition of this chemical class and the role of the cyclobutylamine moiety. Compound 21a demonstrated high enzymatic potency against AKT1, AKT2, and AKT3, as well as potent cellular inhibition of AKT activation and the phosphorylation of the downstream target PRAS40. Compound 21a also served as a potent inhibitor of the AKT1-E17K mutant protein and inhibited tumor growth in a human xenograft mouse model of endometrial adenocarcinoma.

During the manufacturing of pharmaceutical compounds, solvent mixtures are commonly used, where the addition of a cosolvent allows for the tuning of the intermolecular interactions present in the system. Here we demonstrate how a similar effect can be accomplished using a room temperature ionic liquid. The pharmaceutical compound acetaminophen is studied in 21 common ionic liquids composed of a 1-n-alkyl-3-methylimidazolium cation with 1 of 7 anions. Using the acetate anion, we predict a large enhancement in solubility of acetaminophen relative to water. We show how this is caused by a synergistic effect of favorable interactions between the ionic liquid and the phenyl, hydroxyl and amide groups of acetaminophen, demonstrating how the ionic liquid cation and anion may be chosen to preferentially solvate different functional groups of complex pharmaceutical compounds. Additionally, while the use of charge scaling in ionic liquid force fields has previously been found to have a minute effect on ionic liquid structural properties, we find it appreciably affects the computed solvation free energy of acetaminophen, which in turn affects the predicted solubility.

The effect of glucosamine analogues (glucosamine and acetylglucosamine) and free ammonium on the formation of 4-methylimidazole (4-MeI) was investigated in the caramel model reaction systems. Methylglyoxal (MGO) was detected after derivatization by high-performance liquid chromatography with a diode array detector (HPLC-DAD). 4-MeI in the Maillard reaction was tested using a high-performance cation exchange chromatography coupled with APCI-MS (HPCEC-MS). The levels of pyrazines tested by gas chromatography (GC) coupled with MS were applied to mark the condensation reaction between dicarbonyls and free ammonium. Results showed that the formation of 4-MeI and its precursor MGO was inhibited in glucosamine analogue model reaction systems. Besides, the results from pyrazines and brown intensity in glucosamine analogues model reaction systems indicated that glucosamine analogues mainly underwent the reaction of intra-intermolecular polymerization into melanoidins rather than the degradation reaction into MGO. Using glucosamine analogues to produce the caramel color with a low level of 4-MeI was applicable.

In this paper, palladium-catalyzed oxidative cycloaromatization of 2-phenylimidazo[1,2-a]pyridine (PIP) with internal alkyne is studied. From this reaction, two classes of fused N-heterocycle, naphtho[1',2':4,5]imidazo[1,2-a]pyridine (NIP) and imidazo[5,1,2-cd]indolizine (IID), were formed through dehydrogenative coupling featured with cleavage of the C-H bonds located on different moiety of the PIP substrates. Moreover, when 5-methyl-2-phenylimidazo [1,2-a]pyridine or 2-mesitylimidazo[1,2-a]pyridine was used, either NIP or IID could be obtained as an exclusive product with good efficiency. Intriguingly, Pd(II) showed different action mode in promoting this reaction compared with Rh(III) and led to the formation of NIP with reversed regio-selectivity for the reaction of asymmetrical alkyne.

This paper describes the molecular recognition of the tripeptide Tyr-Leu-Ala by the synthetic receptor cucurbit[8]uril (Q8) in aqueous buffer with nanomolar affinity and exceptional specificity. This combination of characteristics, which also applies to antibodies, is desirable for applications in biochemistry and biotechnology but has eluded supramolecular chemists for decades. Building on prior knowledge that Q8 binds to peptides with N-terminal aromatic residues, a library screen of 105 peptides was designed to test the effects of residues adjacent to N-terminal Trp, Phe, or Tyr. The screen used tetramethylbenzobis(imidazolium) (MBBI) as a fluorescent indicator and resulted in the unexpected discovery that MBBI can serve not only as a turn-off sensor via the simultaneous inclusion of a Trp residue but also as a turn-on sensor via the competitive displacement of MBBI upon binding of Phe- or Tyr-terminated peptides. The unusual fluorescence response of the Tyr series prompted further investigation by (1)H NMR spectroscopy, electrospray ionization mass spectrometry, and isothermal titration calorimetry. From these studies, a novel binding motif was discovered in which only 1 equiv of peptide binds to Q8, and the side chains of both the N-terminal Tyr residue and its immediate neighbor bind within the Q8 cavity. For the peptide Tyr-Leu-Ala, the equilibrium dissociation constant value is 7.2 nM, whereas that of its sequence isomer Tyr-Ala-Leu is 34 μM. The high stability, recyclability, and low cost of Q8 combined with the straightforward incorporation of Tyr-Leu-Ala into recombinant proteins should make this system attractive for the development of biological applications.

A polyamide containing N-methylpyrrole (Py) and N-methylimidazole (Im), designated PIPA, binds with high affinity and specificity to specific nucleotide sequences in the minor groove of double-helical DNA. Based on a recent report of the synthesis of PIPA for telomere visualization, the present paper focused on the size of the connecting part (hinge region) of two PIPA segments of the tandem hairpin PIPA, Dab(Im-Im-Py)-Py-Py-Py-Im-[Hinge]-Dab(Im-Im-Py)-Py-Py-Py-Im-βAla-NH(CH2)3N(CH3)-(CH2)3NH-[Dye]. The present paper also describes the characterization of binding by measuring the thermal melting temperature and surface plasmon resonance and by specific staining of telomeres (TTAGGG)n in human cells. Microheterogeneity was also investigated by high-resolution mass spectrometry. We found that the optimal compound as the hinge segment for telomere staining was [-NH(C2H4O)2(C2H4)CO-] with tetramethylrhodamine as the fluorescent dye.

A critical unmet clinical need to combat the global tuberculosis epidemic is the development of potent agents capable of reducing the time of multi-drug-resistant (MDR) and extensively-drug-resistant (XDR) tuberculosis therapy. In this paper, we report on the optimization of imidazo[1,2-a]pyridine amide (IPA) lead compound 1, which led to the design and synthesis of Q203 (50). We found that the amide linker with IPA core is very important for activity against Mycobacterium tuberculosis H37Rv. Linearity and lipophilicity of the amine part in the IPA series play a critical role in improving in vitro and in vivo efficacy and pharmacokinetic profile. The optimized IPAs 49 and 50 showed not only excellent oral bioavailability (80.2% and 90.7%, respectively) with high exposure of the area under curve (AUC) but also displayed significant colony-forming unit (CFU) reduction (1.52 and 3.13 log10 reduction at 10 mg/kg dosing level, respectively) in mouse lung.

2-Acetyl-4-((1R,2S,3R)-1,2,3,4-tetrahydroxybutyl)imidazole (THI) is a minor toxic contaminant observed in caramel food colorings and was shown to exert immunosuppressant activity when fed to rodents. Because of this toxicity, maximum levels of THI in caramel food colorings have been defined by international and European authorities. Several reports of THI analysis using external standardization have been published for liquid foods such as beers and soft drinks. However, no suitable internal standard has yet been described allowing THI analysis in more complex samples. In this paper we describe the preparation of a labeled [(13)C6]THI analogue and its application for the successful validation of the first stable isotope dilution assay (SIDA) of THI in caramel food colorings. A brief survey of THI levels in commercially available caramel class III (E 150c) and IV (E 150d) food colorings is also included, corroborating that THI occurs only in caramel class III food colorings.

The hydrogen ion is one of the most important species in aqueous solutions, as well as in protic ionic liquids (PILs). PILs are important potential alternatives to H2O for swelling the proton exchange membranes (PEMs) and improving the high-temperature performance of fuel cells. The hydrogen ion (H(+)) or hydronium (H3O(+)) solvation mechanism is not only a fundamental principle of acid/base chemistry in ionic liquids but also key to understanding the charge- and proton-transport properties of the PIL solutions. In this paper, a PIL system was prepared by mixing 1-butyl-3-methyl-imidazolium tetrafluoroborate (BMIBF4) IL with an aqueous solution of a strong acid, HBF4. Water can be partially evaporated from the solution under a vacuum at room temperature. Conductivity and vibrational spectroscopy (IR and Raman) measurements were used in combination with density functional theory (DFT) calculations to characterize the molecular-level solvation of H(+) and H2O in the IL solution. When water is present at high molar fraction, the cations (BMI(+) and H(+)) and anions (BF4(-)) are both solvated by water and the solutions have high conductivity. After water evaporation, the PIL solution has excess H(+) and reduced conductivity, which is still significantly higher than that of pure BMIBF4. Vibrational spectroscopy suggests that the BMI(+) and BF4(-) ions are desolvated from water during the water evaporation. DFT calculations assist the interpretation of the vibrational spectroscopy and show that the remaining water is in the form of H3O(+) solvated by the IL molecular ions. Hence, the species remaining after evaporation is a ternary PIL consisting of BMI(+) cation, BF4(-) anion, and H3O(+) cation. The H3O(+) may be the principle charge carrier in the PIL solution and responsible for the high solution conductivity.

The use of chemical preservative compounds is common in the food products industry. Caramel color is the most usual additive used in beverages, desserts, and breads worldwide. During its fabrication process, 2- and 4-methylimidazole (MeI), highly carcinogenic compounds, are generated. In these cases, the development of reliable analytical methods for the monitoring of undesirable compounds is necessary. The primary procedure for the analysis of 2- and 4-MeI is using LC- or GC-MS techniques. These procedures are time-consuming and require large amounts of organic solvents and several pretreatment steps. This prevents the routine use of this procedure. This paper describes a rapid, efficient, and simple method using capillary electrophoresis (CE) for the separation and determination of 2- and 4-MeI in caramel colors. The analyses were performed using a 75 μm i.d. uncoated fused-silica capillary with an effective length of 40 cm and a running electrolyte consisting of 160 mmol L(-1) phosphate plus 30% acetonitrile. The pH was adjusted to 2.5 with triethylamine. The analytes were separated within 6 min at a voltage of 20 kV. Method validation revealed good repeatability of both migration time (<0.8% RSD) and peak area (<2% RSD). Analytical curves for 2- and 4-MeI were linear in the 0.4-40 mg L(-1) concentration interval. Detection limits were 0.16 mg L(-1) for 4-MeI and 0.22 mg L(-1) for 2-MeI. The extraction recoveries were satisfactory. The developed method showed many advantages when compared to the previously used method.

Since the National Toxicology Program (NTP) identified 4(5)-methylimidazole [4(5)-MI] as a cancer causing chemical in 2007 and the State of California added it to the Proposition 65 list of compounds as a carcinogen on January 7, 2011, many researchers and regulatory agencies have become focused on the presence of 4(5)-MI in foods and beverages. 4(5)-MI has been known to form in the Maillard reaction system consisting of a sugar and ammonia-a typical caramel-color preparation method for beverages. 4(5)-MI is identified in various beverages and sauces, which are colored with caramel, as well as in caramel color itself. Analysis of 4(5)-MI is extremely difficult due to its high water solubility, but the analytical method for 4(5)-MI has progressed from conventional paper chromatography, gas chromatography, and gas chromatography-mass spectrometry to the most advanced high-performance liquid chromatography-mass spectrometry. Various studies indicate that caramel colors and carbonated beverages contain 4(5)-MI in levels ranging from 0 to around 1000 ppm and from 0 to about 500 ppm, respectively. Reports of the toxicity of 4(5)-MI at relatively high levels suggest that it may cause some adverse effects on human consumers.

̀This paper reports on the advancement of magnetic ionic liquids (MILs) as stable dispersions of surface-modified γ-Fe(2)O(3), Fe(3)O(4), and CoFe(2)O(4) magnetic nanoparticles (MNPs) in a hydrophobic ionic liquid, 1-n-butyl 3-methylimidazolium bis(trifluoromethanesulfonyl)imide (BMI.NTf(2)). The MNPs were obtained via coprecipitation and were characterized using powder X-ray diffraction, transmission electron microscopy, Raman spectroscopy and Fourier transform near-infrared (FT-NIR) spectroscopy, and magnetic measurements. The surface-modified MNPs (SM-MNPs) were obtained via the silanization of the MNPs with the aid of 1-butyl-3-[3-(trimethoxysilyl)propyl]imidazolium chloride (BMSPI.Cl). The SM-MNPs were characterized by Raman spectroscopy and Fourier transform infrared-attenuated total reflectance (FTIR-ATR) spectroscopy and by magnetic measurements. The FTIR-ATR spectra of the SM-MNPs exhibited characteristic absorptions of the imidazolium and those of the Fe-O-Si-C moieties, confirming the presence of BMSPI.Cl on the MNP surface. Thermogravimetric analysis (TGA) showed that the SM-MNPs were modified by at least one BMSPI.Cl monolayer. The MILs were characterized using Raman spectroscopy, differential scanning calorimetry (DSC), and magnetic measurements. The Raman and DSC results indicated an interaction between the SM-MNPs and the IL. This interaction promotes the formation of a supramolecular structure close to the MNP surface that mimics the IL structure and is responsible for the stability of the MIL. Magnetic measurements of the MILs indicated no hysteresis. Superparamagnetic behavior and a saturation magnetization of ~22 emu/g could be inferred from the magnetic measurements of a sample containing 50% w/w γ-Fe(2)O(3) SM-MNP/BMI.NTf(2).

This paper describes the implementation of a biochemical and biophysical screening strategy to identify and optimize small molecule Akt1 inhibitors that act through a mechanism distinct from that observed for kinase domain ATP-competitive inhibitors. With the aid of an unphosphorylated Akt1 cocrystal structure of 12j solved at 2.25 Å, it was possible to confirm that as a consequence of binding these novel inhibitors, the ATP binding cleft contained a number of hydrophobic residues that occlude ATP binding as expected. These Akt inhibitors potently inhibit intracellular Akt activation and its downstream target (PRAS40) in vitro. In vivo pharmacodynamic and pharmacokinetic studies with two examples, 12e and 12j, showed the series to be similarly effective at inhibiting the activation of Akt and an additional downstream effector (p70S6) following oral dosing in mice.

Protic ionic liquids (PILs) are promising alternatives to water for swelling Nafion as a fuel cell proton exchange membrane (PEM). PILs can significantly improve the high-temperature performance of a PEM. The proton dissociation and solvation mechanisms in a PIL, which are keys to understanding the proton transportation and conductivity, have not been fully explored. In this paper, we used FTIR, Raman, and electronic spectroscopy with computational simulation techniques to explore the spectroscopic properties of bis(trifluoromethanesulfonyl)imide (HTFSI) solutions in 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide (BMITFSI) ionic liquid at concentrations from ∼0.1 to as high as ∼1.0 M. Solution conductivities were measured at room temperature and elevated temperatures up to ∼65 °C. The solution structure and properties depend on the concentration of HTFSI. At lower concentration, around 0.1 M, the HTFSI solution has higher conductivity than pure BMITFSI. However, the conductivity decreases when the concentration increases from 0.1 to 1.0 M. Temperature-dependent conductivities followed the Vogel-Fulcher-Tamman equation at all concentrations. Conductivity and spectroscopy results elucidate the complicated ionization and solvation mechanism of HTFSI in BMITFSI solutions. Raman spectroscopy and density functional theory (DFT) calculations are consistent with the complete ionization of HTFSI to generate solvated H(+) at low concentrations. FTIR, Raman, and electronic spectroscopic results as well as DFT computational simulation indicated that when the concentration is as high as 1.0 M, a significant amount of TFSI(-) is protonated, most likely at the imide nitrogen.

The zinc finger protein EVI1 is causally associated with acute myeloid leukemogenesis, and inhibition of its function with a small molecule therapeutic may provide effective therapy for EVI1-expressing leukemias. In this paper we describe the development of a pyrrole-imidazole polyamide to specifically block EVI1 binding to DNA. We first identify essential domains for leukemogenesis through structure-function studies on both EVI1 and the t(3;21)(q26;q22)-derived RUNX1-MDS1-EVI1 (RME) protein, which revealed that DNA binding to the cognate motif GACAAGATA via the first of two zinc finger domains (ZF1, encompassing fingers 1-7) is essential transforming activity. To inhibit DNA binding via ZF1, we synthesized a pyrrole-imidazole polyamide 1, designed to bind to a subsite within the GACAAGATA motif and thereby block EVI1 binding. DNase I footprinting and electromobility shift assays revealed a specific and high affinity interaction between polyamide 1 and the GACAAGATA motif. In an in vivo CAT reporter assay using NIH-3T3-derived cell line with a chromosome-embedded tet-inducible EVI1-VP16 as well as an EVI1-responsive reporter, polyamide 1 completely blocked EVI1-responsive reporter activity. Growth of a leukemic cell line bearing overexpressed EVI1 was also inhibited by treatment with polyamide 1, while a control cell line lacking EVI1 was not. Finally, colony formation by RME was attenuated by polyamide 1 in a serial replating assay. These studies provide evidence that a cell permeable small molecule may effectively block the activity of a leukemogenic transcription factor and provide a valuable tool to dissect critical functions of EVI1 in leukemogenesis.

All-cellulose nanocomposite was directly fabricated using nanowelding of cellulose microfibers as a starting material, in 1-butyl-3-methylimidazolium chloride (BMIMCl) as a solvent, for the first time. The average diameter of the reinforcing component (undissolved nanofibrils) in the nanocomposite made directly from cellulose microfibers (NC-microfiber) was 53 ± 16 nm. Owing to its high mechanical properties (tensile strength of 208 MPa and Young's modulus of 20 GPa), high transparency (76% at a wavelength of 800 nm), and complete barrier to air and biodegradability, the NC-microfiber is regarded as a high multiperformance material. The NC-microfiber made directly from cellulose microfibers showed similar macro-, micro-, and nanostructures and the same properties as those made from solvent-based welding of ground cellulose nanofibers (NC-nanofiber). Omitting the step of cellulose nanofiber production makes the direct production of all-cellulose nanocomposite from cellulose microfibers easier, shorter, and cheaper than using cellulose nanofibers as starting material. The direct nanowelding of macro/micrometer-sized materials is theorized to be a fundamental approach for making nanocomposites.

N-{trans-3-[(5-Cyano-6-methylpyridin-2-yl)oxy]-2,2,4,4-tetramethylcyclobutyl}imidazo[1,2-a]pyrimidine-3-carboxamide (1) was recently identified as a full antagonist of the androgen receptor, demonstrating excellent in vivo tumor growth inhibition in castration-resistant prostate cancer (CRPC). However, the imidazo[1,2-a]pyrimidine moiety is rapidly metabolized by aldehyde oxidase (AO). The present paper describes a number of medicinal chemistry strategies taken to avoid the AO-mediated oxidation of this particular system. Guided by an AO protein structure-based model, our investigation revealed the most probable site of AO oxidation and the observation that altering the heterocycle or blocking the reactive site are two of the more effective strategies for reducing AO metabolism. These strategies may be useful for other drug discovery programs.

We had previously reported that Mitsunobu-based introduction of alkyl substituents onto the imidazole N(π)-position of a key histidine residue in phosphothreonine-containing peptides can impart high binding affinity against the polo-box domain of polo-like kinase 1. Our current paper investigates the mechanism leading to this N(π)-alkylation and provides synthetic methodologies that permit the facile synthesis of histidine N(π)-modified peptides. These agents represent new and potentially important tools for biological studies.

1-Methylcyclopropene (1-MCP) is an excellent safe and commercially available ethylene antagonist for the preservation of horticultural products. However 1-MCP has to be stored in absorbents due to its gaseous and unstable characteristics. In this paper cucurbit[6]uril (CB[6]) was used as the absorbent to encapsulate 1-MCP, and the resultant inclusion complex was characterized by IR, powder X-ray diffraction, thermal analysis, and fluorescent spectra. The effects of encapsulation conditions on the formation of inclusion complex were also investigated. The amount of 1-MCP encapsulated by CB[6] was about 4.5% by weight when the initial concentration of 1-MCP, encapsulation temperature, CB[6] concentration, and encapsulation time were set at 75 mL/L, 20 °C, 30 mM, and 8 h, respectively. Furthermore, the release of 1-MCP from the complex can be realized with different solutions such as sodium bicarbonate, benzoic acid, and distilled water. CB[6] can be used as an excellent absorbent for encapsulation of 1-MCP.

Recently, a new concept of pH-switchable agents for reversible addition-fragmentation chain transfer (RAFT) polymerization has been introduced by Benaglia et al. (J. Am. Chem. Soc.2009, 131, 6914-6915). In this paper we extended the concept of pH-switchable mediators to nitroxide mediated polymerization (NMP) by employing nitroxides with basic or acidic groups as controlling agents. Four alkoxyamines, the derivatives of 2-(4-(dimethylamino)-2-ethyl-5,5-dimethyl-2-(pyridin-4-yl)-2,5-dihydro-1H-imidazol-1-oxyl and 2-(2-carboxyethyl)-5,5-diethyl-2,4-dimethyl-2,5-dihydro-1H-imidazol-1-oxyl, have been prepared. The influence of pH on alkoxyamine homolysis rate constants (k(d)) and on the nitroxide-alkyl radical recombination rate constants (k(c)) was studied. All alkoxyamines under study as well as the parent nitroxides have several basic groups, which under pH variation can undergo consecutive protonation. It was shown that the k(d) value under basic conditions are significantly (up to 15-fold) higher than in acidic solution at the same temperature, whereas the k(c) value in basic solutions decrease by a factor of 2 only. The efficiency of NMP is known to be dependent on k(d) and k(c), both constants being dependent on the monomer structure; therefore the performance of NMP of different monomers in the controlled mode requires different conditions. It is shown that the pH value crucially affects the polymerization regime, changing it from the controlled to the uncontrolled mode. The controlled regime of NMP of different hydrophilic monomers (sodium 4-styrenesulphonate and acrylamide) in aqueous solution under mild conditions (90 °C) can be achieved using the same alkoxyamine by the variation of the pH value. The chain length of polymers depends on pH value during the polymerization.

The discovery of molecules that bind tightly and selectively to desired proteins continues to drive innovation at the interface of chemistry and biology. This paper describes the binding of human insulin by the synthetic receptor cucurbit[7]uril (Q7) in vitro. Isothermal titration calorimetry and fluorescence spectroscopy experiments show that Q7 binds to insulin with an equilibrium association constant of 1.5 × 10(6) M(-1) and with 50-100-fold selectivity versus proteins that are much larger but lack an N-terminal aromatic residue, and with >1000-fold selectivity versus an insulin variant lacking the N-terminal phenylalanine (Phe) residue. The crystal structure of the Q7·insulin complex shows that binding occurs at the N-terminal Phe residue and that the N-terminus unfolds to enable binding. These findings suggest that site-selective recognition is based on the properties inherent to a protein terminus, including the unique chemical epitope presented by the terminal residue and the greater freedom of the terminus to unfold, like the end of a ball of string, to accommodate binding. Insulin recognition was predicted accurately from studies on short peptides and exemplifies an approach to protein recognition by targeting the terminus., (© 2011 American Chemical Society)

The present paper reports the results of a systematic rheological study of the dynamic moduli of 1-butyl 3-methylimidazolium tetrafluoroborate ([Bmim][BF(4)]), 1-butyl 3-methylimidazolium hexafluorophosphate ([Bmim][PF(6)]), and 1-ethyl 3-methylimidazolium ethylsulfate ([Emim][EtSO(4)]) in the vicinity of their respective glass transition temperatures. The results show an anomalous aging in that the dynamic and the low shear rate viscosities decrease with time at temperatures near to, but above, the glass transition temperature, and this is described. The samples that are aged into equilibrium obey the time-temperature superposition principle, and the shift factors and the viscosities follow classic super-Arrhenius behaviors with intermediate fragility values as the glass transition is approached. Similar experiments using a high-purity [Bmim][BF(4)] show that using a higher purity of the ionic liquid, while changing absolute values of the properties, does not eliminate the anomalous aging response. The data are also analyzed in a fashion similar to that used for polymer melts, and we find that these ionic liquids do not follow, for example, the Cox-Merz relationship between the steady shear viscosity and the dynamic viscosity.

We report the synthesis of two-faced inhibitors 1-5 that contain both enzyme inhibitor and cucurbit[n]uril binding domains. The enzyme binding domains of 1-5 bind to the active sites of bovine carbonic anhydrase (BCA) or acetylcholinesterase (AChE) and inhibit their catalytic activities. Addition of CB[7] to BCA*1 and BCA*2 results in the transient formation of the BCA*1*CB[7] and BCA*2*CB[7] ternary complexes that undergo rapid dissociation to form free catalytically active BCA along with CB[7]*1 and CB[7]*2. The on-off cycle can be performed repetitively by the sequential addition of competitive guest 8 and CB[7]. The detailed origins of this on-off switching of the catalytic activity of BCA is delineated by the combined inference of UV/vis catalytic assays, fluorescence displacement assays, (1)H NMR, along with measurement of the fundamental values of K(a), k(on), and k(off) for the various complexes involved. In contrast, addition of CB[7] to AChE*4(4) and AChE*5(4) results in the formation of thermodynamically stable ternary complexes AChE*4(4)*CB[7](4) and AChE*5(4)*CB[7](4) that are catalytically inactive. We highlight some of the advantages and disadvantages of the strategy, based on the direct competition between two receptors (e.g., enzyme and CB[7]) for a common inhibitor, used in this paper to control enzyme catalytic activity compared to the strategy employed by Nature involving the binding of an allosteric small molecule remote from the enzyme active site.

This paper present ultraviolet-visible absorption spectra of imazamethabenz-methyl (IMBM) (mixture of the isomers methyl 6-[(RS)-4-isopropyl-4-methyl-5-oxo-2-imidazolin-2-yl]-m-toluate, m-imazamethabenz, and methyl 2-[(RS)-4-isopropyl-4-methyl-5-oxo-2-imidazolin-2-yl]-p-toluate, p-imazamethabenz) and the corresponding carboxylic acid, imazamethabenz-acid (IMBA). The spectral characteristics are determined as functions of the pH. The appreciable absorbance in the visible (or near-ultraviolet) region of the spectra indicates that the natural photolytic degradation is possible. From variations of the maximum absorbances of the bands, the pK values of 3.4 +/- 0.2 and 9.4 +/- 0.2 were obtained for protonation of the imidazol (=N-) nitrogen and dissociation of the NH imidazol nitrogen of IMBM, respectively. For IMBA, the dissociation pK of the carboxylic group is very close to that of the imidazol (=N-) nitrogen, both being close to 3.3. The dissociation pK of the NH imidazol nitrogen for IMBA is 9.6 +/- 0.2. The role of the acid-base reactions on the sorption on soils of these herbicides is discussed.

In this paper we report the synthesis of three families of new amidine-based aromatic derivatives as potential DNA minor groove binding agents for the treatment of cancer. The preparation of monoguanidine, mono-2-aminoimidazoline, and asymmetric diphenylguanidine/2-aminoimidazoline derivatives (compounds 1a-c to 8a-c) is presented. The affinity of these substrates and of a family of mono- and bis-isoureas (previously prepared in Rozas' laboratory) for DNA was evaluated by means of DNA thermal denaturation measurements. In particular, compounds 2c, 5c, 6c, 7c, and 8c were found to bind strongly both to natural DNA and to adenine-thymine oligonucleotides, showing a preference for the adenine-thymine base pair sequences.

Four new dimeric pyrrole-2-aminoimidazole alkaloids have been isolated from the Pacific marine sponges Agelas cf. mauritiana and Phakellia sp. They include the unusual C2 symmetrical benzosceptrins A (4) and B (5), which each possess a unique benzocyclobutane skeleton and nagelamides S (6) and T (7). Their structures and relative configuration were elucidated from spectroscopic data. Plausible biogenetic paths for these compounds are also proposed in this paper.

This paper describes a diamination process using di-tert-butyldiaziridinone as nitrogen source and CuCl as catalyst. A wide variety of disubstituted terminal olefins can be efficiently diaminated in good yields under mild condition. This diamination process was used to synthesize potent NK(1) antagonist Sch 425078.

Cytochrome c oxidase (CcO) catalyzes the four-electron reduction of oxygen to water, the one-electron reductant Cytochrome c (Cytc) being the source of electrons. Recently we reported a functional model of CcO that electrochemically catalyzes the four-electron reduction of O(2) to H(2)O (Collman et al. Science 2007, 315, 1565). The current paper shows that the same functional CcO model catalyzes the four-electron reduction of O(2) using the actual biological reductant Cytc in a homogeneous solution. Both single and steady-state turnover kinetics studies indicate that O(2) binding is rate-determining and that O-O bond cleavage and electron transfer from reduced Cytc to the oxidized model complex are relatively fast.

Developing nontraditional approaches to the synthesis and characterization of multivalent compounds is critical to our efforts to study and interface with biological systems and to build new noncovalent materials. This paper demonstrates a biomimetic approach to the construction of discrete, modular, multivalent receptors via molecular self-assembly in aqueous solution. Scaffolds presenting 1-3 viologen groups recruit a respective 1-3 copies of the synthetic host, cucurbit[8]uril, in a noncooperative manner and with a consistent equilibrium association constant (K(a)) value of 2 x 10(6) M(-1) per binding site. The assembled mono-, di-, and trivalent receptors bind to their cognate target peptides containing 1-3 Trp residues with K(a) values in the range 1.7 x 10(4)-4.7 x 10(6) M(-1) and in predetermined mono- or multivalent binding modes with 31-280-fold enhancements in affinity and additive enthalpies due to multivalency. The extent of valency was determined directly by measuring the visible charge-transfer absorptivity due to the viologen-indole pair. The predictable behavior of this system and its ease of synthesis and analysis make it well suited to serve as a model for multivalent binding and for the multivalent recognition of peptides by design.

In this paper, we report the synthesis of three new 2-aminoimidazoline (compounds 4b, 5b, and 6b) and three new guanidine derivatives (compounds 7b, 8b, and 9b) as potential alpha(2)-adrenoceptor antagonists for the treatment of depression. Their pharmacological profile was evaluated in vitro in human brain tissue and compared to the potential antidepressant 1 and the agonists 2 and 3. All new substrates were evaluated by in vitro functional [(35)S]GTPgammaS binding assays in human prefrontal cortex to determine their agonistic or antagonistic activity. Compound 8b was found to be an antagonist in vitro and was subjected to in vivo microdialysis experiments in rats. Moreover, a new synthesis of the precursor amines for compounds 4b-9b is presented.

An efficient process to produce kilogram quantities of a key argininylbenzo[d]thiazole intermediate was developed for the preparation of the tryptase inhibitor RWJ-56423. A variety of activated arginine esters and benzo[d]thiazole nucleophiles were evaluated as coupling partners. Our work led to the selection and optimization of an argininyl imidazolide ester and benzothiazol-2-yl MgCl nucleophile. This paper focuses on the preparation, use, and stability of the benzothiazol-2-yl Grignard reagents.

In the present paper, the electrodeposition of Al on flame-annealed Au(111) and polycrystalline Au substrates in two air- and water-stable ionic liquids namely, 1-butyl-1-methyl-pyrrolidinium bis(trifluoromethylsulfonyl)amide, [Py(1,4)]Tf(2)N, and 1-ethyl-3-methyl-imidazolium bis(trifluoromethylsulfonyl)amide, [EMIm]Tf(2)N, has been investigated by in situ scanning tunneling microscopy (STM), electrochemical quartz crystal microbalance (EQCM), and cyclic voltammetry. The cyclic voltammogram of aluminum deposition and stripping on Au(111) in the upper phase of the biphasic mixture of AlCl(3)/[EMIm]Tf(2)N at room temperature (25 degrees C) shows that the electrodeposition process is completely reversible as also evidenced by in situ STM and EQCM studies. Additionally, a cathodic peak at an electrode potential of about 0.55 V vs Al/Al(III) is correlated to the aluminum UPD process that was evidenced by in situ STM. A surface alloying of Al with Au at the early stage of deposition occurs. It has been found that the Au(111) surface is subject to a restructuring/reconstruction in the upper phase of the biphasic mixture of AlCl(3)/[Py(1,4)]Tf(2)N at room temperature (25 degrees C) and that the deposition is not fully reversible. Furthermore, the underpotential deposition of Al in [Py(1,4)]Tf(2)N is not as clear as in [EMIm]Tf(2)N. The frequency shift in the EQCM experiments in [Py(1,4)]Tf(2)N shows a surprising result as an increase in frequency and a decrease in damping with bulk aluminum deposition at potentials more negative than -1.8 V was observed at room temperature. However, at 100 degrees C there is a frequency decrease with ongoing Al deposition. At -2.0 V vs Al/Al(III), a bulk aluminum deposition sets in.

In this paper, a pseudorotaxane (2) was synthesized by reaction of cucurbit [6]uril with 6-[(6-aminohexyl)amino]-6-deoxy-beta-cyclodextrin chloride. Subsequently, pseudorotaxanes 2 were further assembled to form a 2D pseudopolyrotaxane (3) through an alpha,omega-PPG2000 diamino polymer threading the cavities of cyclodextrins in 2, and the resulting pseudopolyrotaxane was comprehensively characterized by FT-IR, NMR, TG-DTA, elemental analysis, and transmission electron microscopy. Significantly, the 2D pseudopolyrotaxane can turn into a main-chain pseudopolyrotaxane in the presence of base, and then the addition of alpha-cyclodextrins may result in a reversible switch between two different 2D pseudopolyrotaxanes.

The procedure to assess the risk posed by systemic insecticides to honey bees follows the European Directives and depends on the determination of the Hazard Quotient (HQ), though this parameter is not adapted to these molecules. This paper describes a new approach to assess more specifically the risk posed by systemic insecticides to honey bees with the example of imidacloprid (Gaucho). This approach is based on the new and existing chemical substances Directive in which levels of exposure (PEC, Predicted Exposure Concentration) and toxicity (PNEC, Predicted No Effect Concentration) are compared. PECs are determined for different categories of honey bees in relation to the amounts of contaminated pollen and nectar they might consume. PNECs are calculated from data on acute, chronic, and sublethal toxicities of imidacloprid to honey bees, to which selected assessment factors are applied. Results highlight a risk for all categories of honey bees, in particular for hive bees. These data are discussed in the light of field observations made on honey bee mortalities and disappearances. New perspectives are given to better determine the risk posed by systemic insecticides to honey bees.

The molecular recognition of peptides and proteins in aqueous solution by designed molecules remains an elusive goal with broad implications for basic biochemical research and for sensors and separations technologies. This paper describes the recognition of N-terminal tryptophan in aqueous solution by the synthetic host cucurbit[8]uril (Q8). Q8 is known to form 1:1:1 heteroternary complexes with methyl viologen (MV) and a second aromatic guest. Here, the complexes of Q8.MV with (i) the four natural aromatic alpha-amino acids, (ii) four singly charged tryptophan derivatives, and (iii) four tryptophan-containing tripeptides were characterized by isothermal titration calorimetry, mass spectrometry, and UV-visible, fluorescence, and (1)H NMR spectroscopy. We find that Q8.MV binds Trp-Gly-Gly with high affinity (K(a) = 1.3 x 10(5) M(-1)), with 6-fold specificity over Gly-Trp-Gly, and with 40-fold specificity over Gly-Gly-Trp. Analysis of the nine indole-containing compounds suggests that peptide recognition is mediated by the electrostatic charge(s) proximal to the indole, and that the mode of binding is consistent for these compounds. Complex formation is accompanied by the growth of a visible charge-transfer band and the quenching of indole fluorescence. These optical properties, combined with the stability and selectivity of this system, are promising for applications in sensing and separating specific peptides.

This paper reports the synthesis of a new series of 3-(5-imidazo[2,1-b]thiazolylmethylene)-2-indolinones which were tested as potential antitumor agents at the National Cancer Institute. Two derivatives are now under review by BEC (Biological Evaluation Committee of NCI). To investigate the mechanism of action, the effect on cell cycle progression was studied by monitoring them in colon adenocarcinoma HT-29: both were able to block HT-29 in mitosis. 3-[(2,6-Dimethylimidazo[2,1-b]thiazol-5-yl)methylene]-5-chloro-2-indolinone was the most active compound.

1-[(Aryl)(4-aryl-1H-pyrrol-3-yl)methyl]-1H-imidazoles were recently reported by our group as potent anti-Candida agents belonging to the antifungal azole class. In the present paper the synthesis, anti-Candida activities, and QSAR studies on a novel series of N-substituted 1-[(aryl)(4-aryl-1H-pyrrol-3-yl)methyl]-1H-imidazole derivatives are reported. The newly synthesized azoles were tested against 12 strains of Candida albicans together with bifonazole, miconazole, itraconazole, fluconazole, and compounds 1a, 1b, 3a, 3b, and 3c used as reference drugs. In general, tested derivatives showed good antifungal activities, and the most potent compound was 1d (MIC(90) = 0.032 microg/mL), which was from 4- to 250-fold more potent than reference drugs. Catalyst software was applied to develop a quantitative pharmacophore model to be used for the rational design of new antifungal azoles. Some key interactions, as well as excluded volumes, further to the coordination bond of azole antifungals with the demethylase enzyme, are highlighted.

Compounds presenting an additional fused ring on the xanthine nucleus have been reported to exhibit antagonistic activity with various levels of affinity and selectivity toward the four adenosine receptors subtypes A(1), A(2A), A(2B), and A(3). This paper reports synthesis and biological evaluation of new 1-benzyl-3-propyl-1H,6H-pyrrolo[2,1-f]purine-2,4-diones and 1-benzyl-3-propyl-1H,8H-imidazo[2,1-f]purine-2,4-diones, among which we identified potent and selective A(3) adenosine receptors antagonists. In particular, 1-benzyl-7-methyl-3-propyl-1H,8H-imidazo[2,1-f]purine-2,4-dione (11e) shows a K(i) (hA(3)) value from binding assay of 0.8 nM.

This paper describes the host properties of a new cucurbit[6]uril analogue, studied by fluorescence and 1H NMR spectroscopy. This host has an elongated cavity with oval-shaped portals. It is intrinsically fluorescent, and more importantly, this fluorescence is sensitive to guest encapsulation, allowing for the study of the inclusion of nonfluorescent guests by fluorescence spectroscopy. In the case of benzene as guest, significant enhancement of the cucurbit[6]uril analogue host fluorescence was observed upon addition of benzene; this allowed for the determination of the binding constant for 1:1 host-guest complexation, yielding a value of K = 6900 +/- 1100 M(-1). This complexation was also studied by 1H NMR, yielding a similar value of K = 8980 +/- 500 M(-1). The binding of a much larger guest, the dye Nile Red, was also studied, but in this case using guest fluorescence. Significant suppression of the Nile Red fluorescence was observed upon 1:1 complexation with the cucurbit[6]uril analogue, with an extremely large binding constant of 8.2 +/- 0.5 x 10(6) M(-1), indicating a very strong host-guest interaction and an excellent size and shape match. In both cases, binding was much stronger than in the case of the same guests with cucurbit[6]uril itself, and in the case of Nile Red, binding was also much stronger than with modified beta- or gamma-cyclodextrins. This is partly a result of the partial aromatic nature of the host walls, which allow for pi-pi interactions not possible in cucurbiturils or cyclodextrins. The ability to study its inclusion complexes using either host or guest fluorescence, and the very high binding constants observed, illustrates the versatility and potential usefulness of this new host compound.

This paper reports synthesis and antitumor activity of new guanylhydrazones from imidazo[2,1-b]thiazoles and from the new heterocyclic system thiazolo[2',3':2,3]imidazo[4,5-c]quinoline. The compounds were tested as potential antitumor agents at the National Cancer Institute. The effect of the guanylhydrazone of 2-chloro-6-(2,5-dimethoxy-4-nitrophenyl)imidazo[2,1-b]thiazole-5-carbaldehyde (41) was investigated, and it was found to be an inhibitor of Complex III of the mitochondrial respiratory chain and is able to induce apoptosis in the cell lines HT29 and HL60.

This paper details the copper-catalyzed N-arylation of pi-excessive nitrogen heterocycles. The coupling of either aryl iodides or aryl bromides with common nitrogen heterocycles (pyrroles, pyrazoles, indazoles, imidazoles, and triazoles) was successfully performed in good yield with catalysts derived from diamine ligands and CuI. General conditions were found that tolerate functional groups such as aldehydes, ketones, alcohols, primary amines, and nitriles on the aryl halide or heterocycle. Hindered aryl halides or heterocycles were also found to be suitable substrates using the conditions reported herein., (Copyright 2004 American Chemical Society)

Antagonizing the robust stimulation of food intake by neuropeptide Y represents a new potential therapeutic approach for the treatment of obesity. Earlier pharmacological studies have pointed to the Y1 and Y5 receptors as the most likely mediators of the NPY orexigenic response. In this paper, we describe a new series of small molecule Y5 antagonists derived from a 2,4-diaryl-1H-imidazole lead. The main objectives of our structural optimization efforts were to produce novel and potent Y5 antagonists with an improved oral pharmacokinetic profile and less affinity for the hERG potassium channel compared to the lead 2,4-diarylimidazole structures. These goals were accomplished by replacement of the 2-aryl ring with a cyclohexyl ring and subsequent elaboration of the 4-position of the cyclohexyl ring with a variety of hydrophilic functionalities. The resulting compound, N-(2-hydroxy-tert-butyl)(4-[4-[3-(trifluoromethyl)phenyl]imidazol-2-yl]cyclohexyl)carboxamide (20), displayed good potency at the Y5 receptor (K(i) = 3 nM), while interactions at the hERG channel were essentially eliminated (6% inhibition at a concentration of 3 microM). Importantly, the pharmacokinetic properties of 20 (F = 36%) represented a marked improvement over that of the initial 2,4-diarylimidazole structures.

In this paper we show that 4-aryl-CH2-imidazole-substituted benzopyran compounds with 3S,4R-stereochemistry are cardioprotective by inhibiting the F1F0 mitochondrial ATP hydrolase. Compounds (e.g., 13) with 3R,4S-stereochemistry act as mitochondrial KATP openers. This resulted from an inversion of stereochemistry for the F1F0 mitochondrial ATP hydrolase vs mitochondrial KATP. Structure-activity relationships for the inhibition of mitochondrial ATP hydrolase are also delineated. It is not clear how 13 (3R,4S) can selectively inhibit the hydrolytic activity of the F1F0 mitochondrial enzyme without interfering with the synthase activity.