Search

Herein, a scheme of Sr2+/Ca2+ ion substitution was employed to simultaneously regulate the defect and intervalence charge transfer (IVCT) state of Sr2−xCaxNb2O7:Pr3+ phosphors, resulting in a dual-modulation strategy for enhancing phosphor thermal stability. [ABSTRACT FROM AUTHOR]

Praseodymium (Pr3+) ion and the transition metal vanadium (V5+) ion with d0 electronic configuration can form an intervalence charge transfer (IVCT) band, which can function both as a compensatory channel for its red emission and as a quenching channel, thus affecting the luminescence thermal stability of the phosphors. Research studies reveal that the emission of Pr3+ in the YVO4 matrix can be quenched by the IVCT mechanism, thereby limiting the application of phosphors. As such, the present contribution is based on the solid solution replacement strategy to inhibit the constitutent of the IVCT quenching channel and thus improve thermal stability. Therefore, phosphonium (P5+) with a valence state matching V5+ and a similar ion radius was selected for the V/P substitution. It lacks a d0 electron configuration, preventing the formation of an IVCT band with Pr3+ and thereby inhibiting the construction of the quenching channels to enhance thermal stability. While the empirical formula of IVCT indicates a decrease in the IVCT energy level from 3.32438 to 3.06251 eV upon the introduction of P5+, the PLE spectra demonstrate a sharp reduction in IVCT intensity, i.e., weakening of the quenching channel. The thermal stability of the phosphors at different excitation locations was enhanced with the rise of P5+ concentration. When excited at the 3P2 level, the Y0.995PO4:0.5%Pr3+ phosphor demonstrated highly stable red emission from 303 to 523 K, with a luminescence integrated intensity ranging from 95.5% to 105.3% compared to that at 303 K. This research provides a novel approach for inhibiting the IVCT quenching channel and broadens the commercial value of YVO4:Pr3+ phosphor for various applications. [ABSTRACT FROM AUTHOR]

Non-noble metal for surface plasmon resonance (SPR)-induced nano-enzymatic photoelectrochemical (PEC) biosensors is a promising method for broad applications. Non-noble metal bismuth (Bi) is gradually being valued for their properties such as non-toxicity, abundant reserves, and good catalysis. Meanwhile, metallic Bi nanoparticles (NPs) have superior SPR properties similar to that of noble metal. Therefore, a non-noble metal Bi/BiVO4 photoanode based on SPR was designed for the PEC detection of H2O2 in this work. The synergistic effect of BiVO4 with suitable band gap (2.5 eV) and Bi NPs with superior SPR effectively reduces the recombination of photogenerated electrons and holes, which significantly improves the PEC activity of Bi/BiVO4 electrode at low voltage. The in situ Bi/BiVO4/FTO photoelectrode not only exhibits a more comprehensive linear range of 0.005–2.6 mM with a lower detection limit of 2.0 μM but also possesses excellent selectivity for the determination of H2O2 because the coexisting substances are difficult to be oxidized at 0 V bias voltage. The investigation of Bi/BiVO4-based sensor has contributed to the development of non-noble metal for SPR-induced PEC biosensors. [ABSTRACT FROM AUTHOR]

The synthesis conditions of most phosphors doped with lanthanide ions with d–f transition require a reducing atmosphere. The doping Bi3+ ions selected in this study perfectly avoid this requirement, and they are environmentally friendly and safe. Nevertheless, the spectral tuning of Bi3+ is a great challenge that limits its application. Herein, by regulating the value of x in the new solid solution Sr2+xLa1−xGaO5−xFx, the luminescence of Bi3+ is well promoted. Through an excitation-driven strategy, the emission peak position of Bi3+ is redshifted, and the luminescence of trivalent bismuth is successfully adjusted, which can also be applied to anti-blue lighting. In addition, we constructed a Bi3+–Eu3+ dual luminescence system, and, regardless of changes in the Bi3+/Eu3+ concentration or excitation wavelength, a single matrix white light phosphor was realized. Through calculations, the activation energy of the phosphor doped with 2.5%Eu3+ was found to be 0.257 eV, which is higher than the activation energy of some common compounds. This indicates that the phosphor has good application prospects in the field of solid-state lighting. It is worth noting that based on the different thermal response behaviors of Bi3+ and Eu3+, when the Eu3+ content is fixed at 1%, the maximum relative sensitivity of the optical thermometer based on its fluorescence intensity ratio is about 1.46% K−1 at 383 K, which is higher than that of Bi3+ and Eu3+ co-doped phosphors previously reported. We also obtained a high absolute sensitivity of 0.00139 K−1 at 403 K. Therefore, we also studied the thermal sensitivity of Bi3+ and Er3+ co-doped solid solutions. The results show that this solid-solution phosphor has far-reaching application prospects in the temperature sensing field. [ABSTRACT FROM AUTHOR]

Additive manufacturing (AM) is an innovative procedure that can quickly create complex structures. By layering a material, a three-dimensional object is created using this technique. Every deposit of liquefied or partly liquefied material abides by the previous deposit. Fused deposition modelling's (FDM) objective is to comprehend how varied interior structures influence the bending resistance of the printed samples and to investigate the impact of various infill patterns and percentages. The term "infill" describes the pattern of solid material used to fill a 3D-printed object's interior. It is utilized to give the printed part structural support and strength. Acrylonitrile butadiene styrene (ABS) material was chosen for this study as it offers a greater and superior finished plane along with dimensional stability. The infill pattern chosen for the flexural test study was the triangular pattern which includes different densities of infill percentages precisely, 25%, 50%, 75%, and 100%. A few specimens of ABS material having 100% infill density are put through a tensile test according to the ASTM D638. The ASTM D790 standard was used to make a model and test the flexural strength of the specimen. Line and triangle patterns provided the most ideal tensile and bending strength properties. This is likely because the deposited rasters are associated with the direction of loading. For line patterns with 100% infill, scanning electron microscopy (SEM) analysis showed a convincing connection between the microstructures and the rasters (porosity, voids, gap between beads and hole due to polymer pulled out). Furthermore, SEM analysis showed matrix failure and significant voids in a triangular pattern at infill densities of 25%, 50%, 75%, and 100%. [ABSTRACT FROM AUTHOR]