Search

This research study highlights into the dynamics of vortex-induced vibrations (VIV) in a rigid cylinder, employing computational fluid dynamics (CFD) simulations validated against experimental data. The primary objective is to explore the potential of harnessing energy from fluid flow-induced vibrations, particularly at lower flow speeds, which are traditionally overlooked by conventional turbine technologies. The CFD simulations investigated the transverse vibrations of a rigid cylinder with elastic support across a wide range of Reynolds numbers. The numerical results were compared with experimental data obtained from the University of Michigan, demonstrating strong correlation, especially for a spring stiffness of 1200 N/m, zero damping, and a relative mass of 1.89. Under these conditions, the maximum relative amplitude of 1.75 was achieved at a Reynolds number of 90,000. The study revealed that increasing spring stiffness up to 1200 N/m enhances the oscillation amplitude. However, further increases in stiffness lead to a decrease in amplitude. Damping and relative mass also significantly influence the vibration behavior. Lower relative masses and damping ratios result in larger amplitude oscillations over a broader range of Reynolds numbers. These findings underscore the feasibility and potential of energy extraction from fluid flows that were previously considered unsuitable. The quantitative insights provided in this study offer valuable guidance for the design and optimization of VIV energy converters. Future research should focus on long-term simulations to further elucidate the impact of these parameters on the performance and durability of such systems.

Introduction: In North India, orthopedic trauma, which refers to injuries affecting the bones, joints, and soft tissues, occurs frequently in pediatric patients. The aim of this study is to investigate the epidemiology, etiology, mechanisms of injury, and outcomes of orthopedic trauma in pediatric patients who are admitted to a tertiary care trauma center located in North India. Materials and Methods: This prospective study was carried out over 1 year between January 2019 and December 2019, which included 479 pediatric orthopedic trauma patients between the age group of 0 and 18 years. The collected data were systematically classified and analyzed with respect to the mode of trauma, type of injury, and outcome across various age groups and genders. Results: Age of children ranged from 0 to 18 years, of which 298 (62.2%) were male and 181 (37.8%) were female. Most fractures occurred at aged 9–12 years (38.4%) and the trend decreased with age. Fall injuries were the most common mode of trauma (49.9%, n = 239) followed by road traffic accident (29.4%, n = 141). Among operated patients, most injuries were closed (47.2%, n = 138) followed by compound injuries (32.2%, n = 94) and crush injuries (20.6%, n = 60). Sixty-three percentage of patients recovered well with independent functional status, while 30% recovered with supported functional status/residual deformity. Conclusion: Orthopedic trauma in pediatric population is growing up and prehospital care is lagging which is more required than adult counterpart. An effective and aggressive management of accident prevention programme is required, which should also include changes in lifestyle and environment, overcoming obstacles such as ignorance, inadequate resources, and illiteracy.

The present research focuses on the effects of different processing routes on the physical and mechanical properties of nano Ti(CN)-based cermets with metallic binders. Tungsten carbide (WC) is added as a secondary carbide and Ni-Co is added as a metallic binder to nano Ti(CN)-based cermet processed via conventional and spark plasma sintering (SPS). A systematic comparison of the composition and sintering conditions for different cermets’ systems was carried out to design novel composition and sintering conditions. Nano TiCN powder was prepared by 30 h of ball milling. The highest density of >98.5% was achieved for the SPS-processed cermets sintered at 1200 °C and 1250 °C for 3 min at 60 MPa of pressure in comparison to the conventionally sintered cermets at 1400 °C for 1 h with a two-stage compaction process—uniaxially at 150 MPa and isostatically at 300 MPa of pressure. Comparative X-ray diffraction (XRD) analysis of the milled powders at different time intervals was performed to understand the characteristics of the as-received and milled powders. Peak broadening was observed after 5 h of ball milling, and it increased to 30 hr. Also, peak broadening and a refined carbide size was observed in the XRD and scanning electron microscope (SEM) micrographs of the SPS-processed cermet. Transmission electron microscope (TEM) analysis of the milled powder showed that its internal structure had a regular periodic arrangement of planes. SEM base scattered electron (BSE) images of all the cermets primarily showed three major microstructural phases of the core–rim–binder with black, grey, and white contrast, respectively. With the present sintering conditions, a high hardness of ~16 GPa and a fracture toughness of ~9 MPa m1/2 were obtained for SPS-processed cermets sintered at higher temperatures.

The significant increase in the human population, energy consumption in daily living is increasing. One approach is to raise the amount of power produced to match the growth in human population, although this is typically practically unfeasible. By controlling demand, electricity consumption and associated expenses may be reduced. As a consequence, we employ Demand-side Management (DSM) to plan different gadgets on loads to reduce energy usage. Incorporating renewable energy sources and reducing energy costs are two significant roles that the smart grid plays. As a result, we suggest a hybrid swarm based Harris Hawks' optimization (S–HHO) algorithm to overcome the optimization difficulties. The suggested approach includes loads of home and business variety. The proposed technique was compared to binary particle swarm optimization (BPSO), multi-objective particle swarm optimization (MOPSO), wind driven optimization (WDO), and multi-objective genetic algorithms (MOGA). Results from simulations were produced using MATLAB software. The results show that the improved hybrid optimization S–HHO reduces the Peak-to-average ratio (PAR) and computational time better than other methods such as WDO, BPSO, MOPSO, and MOGA.

Aims and Objectives: This study aimed to evaluate the functional results and clinicoradiological outcomes of extra-articular closed proximal third tibia fractures managed by suprapatellar nailing in semi-extended position with a minimum follow-up of 12 months. Materials and Methods: In our prospective study, 15 cases of extra-articular closed proximal third tibia fractures admitted between January 2019 to December 2020, treated with intramedullary nailing through suprapatellar approach, were included. The patients were followed up regularly at 2 weeks, 6 weeks, 3 months, 6 months, 12 months, and every 6 months thereafter. The clinical outcome was analyzed using the Lower Extremity Functional Scale (LEFS) at 12 months’ follow-up visit. The radiological outcomes were analyzed by evaluating the radiographs for fracture union and alignment. Results: Fifteen patients having proximal third tibia fracture fulfilling the inclusion and exclusion criteria were included in the study. Patients had an average age of 34 years (24–55 years). The average follow-up period was 14 months (12–18 months) after the index procedure. The average time for radiological union was 6 months (range: 4–12 months). Two patients had procurvatum malalignment of >10°. We did not have significant rotational or varus/valgus malalignment or limb length discrepancy of >1 cm in our study. The average LEFS score at the 12 months’ follow-up was 88% (median: 90%; range: 80%–98%). Conclusion: We recommend the use of intramedullary suprapatellar nailing for fixation of proximal third tibial fractures. Suprapatellar nailing has inherent advantages of patient positioning for perfect nail entry and placement. When performed following the established surgical principles and techniques and proper patient and implant selection, it provides excellent clinicoradiological outcome with less complications as compared to other fixation methods for such fractures. There is also absence of anterior knee pain which is very common in the standard infrapatellar approach due to which its use could be extended for nailing of all types of tibia fractures.

Channel flow with baffles is a multifaceted phenomenon with wide-ranging applications. It plays a crucial role in enhancing mixing, heat transfer, and other fluid dynamics processes. The baffles' design and placement within the channel are crucial to achieving the desired heat transfer enhancement. Based on the specific application and fluid properties, such as baffle geometry, spacing, and orientation must be considered. This work aims to visualize, evaluate, and understand the effectiveness of baffles on heat transfer rates under various operating conditions and design parameters. Computational Fluid Dynamic (CFD) investigations were carried out to examine the performance of channels for various geometrical configurations including Broken V-shaped, Circular, and triangular at wide operating conditions, and baffle number densities. Computational fluid dynamic (CFD) simulations were carried out for three different baffle shapes while the Reynolds number (Re) ranged from 1800 to 22000 and the no. of baffle sets(N), varied as N=15,20,30. At low Re conditions channel with 30 sets of Broken-V-shape baffles results in a higher Nusselt number due to effective turbulence enhancement and mixing in the channel. Although the thermal performance of a V-shaped baffles case is relatively good the friction factor is more for this case. Triangular baffles exhibited a lower friction factor. A maximum friction factor of 0.92 is observed for N=30 sets at Re= 1800 while the least of 0.76 is recorded for N=15.

Effective maintenance coordination has become essential to ensuring a reliable electricity supply in power systems primarily powered by renewable sources. On the other hand, the computational complexity of the operational security standards presents difficulties for the existing planning tools. To solve this problem, a research paper suggests applying the machine learning (ML) method known as lightning search optimised random forest (LSORF) to anticipate the results of contingency analyses rapidly and effectively. The entire regional transmission system of Belgium (BE), which includes voltage ranges of 200 kV to 50 kV, is the subject of the study. Results show that LSORF regularly outperforms other benchmarks. The results demonstrate that LSORF consistently outperforms other benchmark methods. Furthermore, the study highlights the impact of projected growth in renewable energy on maintenance feasibility. This strategy provides useful insights for improving maintenance planning in renewable energy systems.

Introduction: Thromboangiitis obliterans (TAO), also known as Buerger's disease, is a disease of unknown etiology affecting small- and medium-sized blood vessels, mainly seen in heavy smokers. The characteristic features of this disease are distal ischemia, with patients having claudication, rest pain, and toe ulcers. The proper management of TAO is still a challenging problem. Various medical and surgical treatments have been tried with a variable success. Since it is a disease characterized by chronic ischemia, achieving neoangiogenesis could have a beneficial effect. Ilizarov has shown that corticotomy and distraction of bony fragments can increase the blood supply to the entire limb. TAO can be managed using this principle of distraction osteogenesis to induce neoangiogenesis. We conducted this study to evaluate the clinical outcomes of longitudinal tibial corticotomy and horizontal distraction with Ilizarov's fixator in Buerger's disease of the lower limb. Materials and Methods: Ten patients with clinically and radiologically proven Buerger's disease admitted to our hospital between 2019 and 2021 who had failed the conservative pharmacological modalities of treatment were included. A lateral tibial corticotomy and distraction was performed by the use of olive wires and two-ring frame with horizontal distraction mechanism. Lateral distraction was started after 10 days at the rate of 0.25 mm 6 h for 25 days to achieve a distraction of 2.5 cm. The frame was removed after consolidation of regenerate. Results: Of the 10 cases, eight patients became pain free, while one had a partial relief of pain and one patient worsened on treatment and underwent below-knee amputation. Three patients had at least one episode of pin site infection which improved with oral antibiotics and dressings. One patient had delayed consolidation of regenerate. The claudication distance improved at each follow-up for all but one patient. Conclusion: Neoangiogenesis by corticotomy and distraction offers a relatively simple and cost-effective surgical option to salvage ischemic limbs from amputations and provide pain relief, ischemic ulcer healing, and improved claudication distance, thus improving the quality of life.

We measured COVID-19-related stigma and discrimination and its drivers using a concurrent mixed-methods design in Punjab. The simple random sampling was used to select blocks, subcenters, and urban primary healthcenters from each of the four selected districts. The systematic random sampling was used to select households. A sample of 423 adults was interviewed using a structured questionnaire and 10 in-depth interviews were conducted using an interview guide. Binary logistic regression was performed to find the predictors. Stigma prevalence was mild 18%, moderate 45%, and severe 37%. Logistic regression indicated that stigma was lower in the rural compared to the urban population (P < 0.01). Hospitalized patients faced discrimination more often compared to those who were treated/quarantined at home. People feared police (71%), testing (69%), and contracting the infection (65%). Fear of screening, disclosure of status, and transmission of the virus were the drivers of stigma and discrimination. Co-occurrence of labeling, stereotyping, and cognitive separation was observed.

Background: Depressive symptoms have been reported in admitted patients of musculoskeletal trauma. However, prevalence and associations of depression have not been reported after definitive management of injury. Aims and Objectives: The objectives of this study were to document the presence of depressive symptoms in adult musculoskeletal injury patients and identify factors associated with an abnormal score on the depression sub-scale of HADS at 4-weeks since admission. Materials and Methods: A longitudinal cohort study was undertaken on musculoskeletal injury patients admitted in the orthopedics department. Patients were enrolled on a randomly chosen day of the week. Subjects were excluded if they suffered from conditions known to preclude the assessment of the mental status. Age, sex, injury severity score, matrimonial status, insurance status, educational status, economic condition, support from family, alcohol abuse, and cannabis abuse were recorded at the time of admission. At 4-weeks after admission, enrolled subjects were screened for depression using the depression subscale of Hospital anxiety and depression scale score. Pain was recorded using visual analogue scale (VAS). Bivariate and multivariate analysis was used to identify predictors of an abnormal HADS score. Results: One-hundred ninety subjects were included. Average age of the subjects was 33.8 years. Thirty nine (21.53%) were females. At 4-weeks, 49 (25.79%) had an abnormal HADS score. A higher VAS score for pain, a younger age, living in a nuclear family and cannabis abuse were associated with an abnormal HADS score. Conclusion: Depressive symptoms are common in musculoskeletal injury patients at 4-weeks after admission.

The present investigation was conducted at the Breeder Seed Production Unit, Jawaharlal Nehru Krishi Vishwa Vidyalaya, Jabalpur, M.P., India during November to April, (Rabi season), 2021 to 2022 analyse grain yield and its attributing traits of wheat by correlation and path coefficient analysis. The twenty genotypes were in randomized complete block design with three replications. The results indicated that the biological yield per plant had highly significant correlation followed by harvest index with a moderate positive value and is significant with the grain yield per plant. Similarly the analysis of direct and indirect effects shows that the plant height, flag leaf length, flag leaf width, days to 50% flowering, grains per spike, biological yield per plant, and harvest index had positive direct effect on grain yield per plant. Hence it may be considered that traits namely, plant height, flag leaf length, flag leaf width, days to 50% flowering, grains per spike, biological yield per plant, and harvest index may be utilized for yield improvement breeding strategies in wheat. However, biological yield and harvest index will be given prime importance during selection of traits, due to their significant association and having a direct or indirect effect in crop yield improvement.