Search

Nanomaterials are integrated within consumer products to enhance specific properties of interest. Their release throughout the lifecycle of nano-enabled products raises concerns; specifically, mechanical strains can lead to the generation of fragmented materials containing nanomaterials. We investigated the potential release of single-walled carbon nanotubes (SWCNTs—brand TUBALL™) from epoxy composite materials. A pin-on-disk-type tribometer was used for the accelerated mechanical aging of the nanocomposites. A pristine nanocomposite material, abraded material and debris obtained from the abrasion in the tribometer were analyzed by Raman spectroscopy. The airborne-produced particles were captured using particle collectors. Stat Peel's Identifier C2 system was used to monitor the SWCNT content of respirable particles produced during the abrasion test. The SWCNT amounts found were below the LoQ. The Raman spectra conducted on the Stat Peel filters helped identify the presence of free SWCNTs released from the epoxy matrix, although they were notably scarce. Raman spectroscopy has been proved to be a crucial technique for the identification, characterization and assessment of structural changes and degradation in SWCNTs that occurred during the abrasion experiments. [ABSTRACT FROM AUTHOR]

The global trend in restrictions on pollutant emissions requires the use of catalytic converters in the automotive industry. Noble metals belonging to the platinum group metals (PGMs, platinum, palladium, and rhodium) are currently used for autocatalysts. However, recent efforts focus on the development of new catalytic converters that combine high activity and reduced cost, attracting the interest of the automotive industry. Among them, the partial substitution of PGMs by abundant non-PGMs (transition metals such as copper) seems to be a promising alternative. The PROMETHEUS catalyst (PROM100) is a polymetallic nanosized copper-based catalyst for automotives prepared by a wet impregnation method, using as a carrier an inorganic mixed oxide (CeO2-ZrO2) exhibiting elevated oxygen storage capacity. On the other hand, catalyst deactivation or ageing is defined as the process in which the structure and state of the catalyst change, leading to the loss of the catalyst's active sites with a subsequent decrease in the catalyst's performance, significantly affecting the emissions of the catalyst. The main scope of this research is to investigate in detail the effect of ageing on this low-cost, effective catalyst. To that end, a detailed characterization has been performed with a train of methods, such as SEM, Raman, XRD, XRF, BET and XPS, to both ceria–zirconia mixed inorganic oxide support (CZ-fresh and -aged) and to the copper-based catalyst (PROM100-fresh and -aged), revealing the impact of ageing on catalytic efficiency. It was found that ageing affects the Ce–Zr mixed oxide structure by initiating the formation of distinct ZrO2 and CeO2 structures monitored by Raman and XRD. In addition, it crucially affects the morphology of the sample by reducing the surface area by a factor of nearly two orders of magnitude and increasing particle size as indicated by BET and SEM due to sintering. Finally, the Pd concentration was found to be considerably reduced from the material's surface as suggested by XPS data. The above-mentioned alterations observed after ageing increased the light-off temperatures by more than 175 °C, compared to the fresh sample, without affecting the overall efficiency of the catalyst for CO and CH4 oxidation reactions. Metal particle and CeZr carrier sintering, washcoat loss as well as partial metal encapsulation by Cu and/or CeZrO4 are identified as the main causes for the deactivation after hydrothermal ageing. [ABSTRACT FROM AUTHOR]

Self-healing materials and self-healing mechanisms are two topics that have attracted huge scientific interest in recent decades. Macromolecular chemistry can provide appropriately tailored functional polymers with desired healing properties. Herein, we report the incorporation of glycidyl methacrylate-based (GMA) copolymers in waterborne polyurethanes (WPUs) and the study of their potential healing ability. Two types of copolymers were synthesized, namely the hydrophobic P(BA-co-GMAy) copolymers of GMA with n-butyl acrylate (BA) and the amphiphilic copolymers P(PEGMA-co-GMAy) of GMA with a poly(ethylene glycol) methyl ether methacrylate (PEGMA) macromonomer. We demonstrate that the blending of these types of copolymers with two WPUs leads to homogenous composites. While the addition of P(BA-co-GMAy) in the WPUs leads to amorphous materials, the addition of P(PEGMA-co-GMAy) copolymers leads to hybrid composite systems varying from amorphous to semi-crystalline, depending on copolymer or blend composition. The healing efficiency of these copolymers was explored upon application of two external triggers (addition of water or heating). Promising healing results were exhibited by the final composites when water was used as a healing trigger. [ABSTRACT FROM AUTHOR]

A notable application of polymeric nanocomposites is the design of water vapor permeable (WVP) membranes. "Breathable" membranes can be created by the incorporation of micro/nanofillers, such as CaCO3, that interrupt the continuity of the polymeric phase and when subjected to additional uniaxial or biaxial stretching this process leads to the formation of micro/nanoporous structures. Among the candidate nanofillers, carbon nanotubes (CNTs) have demonstrated excellent intrinsic WVP properties. In this study, chemically modified MWCNTs with oligo olefin-type groups (MWCNT-g-PP) are incorporated by melt processes into a PP matrix; a β-nucleating agent (β-ΝA) is also added. The crystallization behavior of the nanocomposite films is evaluated by differential scanning calorimetry (DSC) and X-ray diffraction (XRD). The WVP performance of the films is assessed via the "wet" cup method. The nanohybrid systems, incorporating both MWCNT-g-PP and β-NA, exhibit enhanced WVP compared to films containing only MWCNT-g-PP or β-NA. This improvement can be attributed to the significant increase in the growth of α-type crystals taking place at the edges of the CNTs. This increased crystal growth exerts a form of stress on the metastable β-phase, thereby expanding the initial microporosity. In parallel, the coexistence of the inherently water vapor-permeable CNTs, further enhances the water vapor permeability reaching a specific water vapor transmission rate (Sp.WVTR) of 5500 μm.g/m2.day in the hybrid composite compared to 1000 μm.g/m2.day in neat PP. Notably, the functionalized MWCNT-g-PP used as nanofiller in the preparation of the "breathable" PP films demonstrated no noteworthy cytotoxicity levels within the low concentration range used, an important factor in terms of sustainability. [ABSTRACT FROM AUTHOR]

Microcapsules (MCs) containing isocyanate compounds for use as self-healing materials in waterborne polyurethane coatings have been synthesized, in the presence of modified Novolac resins. With modification of Novolac resin, it is succeeded partial or total protection (Benzylation and Acetylation) of its hydroxyl groups. The idea here is to use a protected Novolac resin as the organic substrate for the encapsulation of the less reactive Isophorone isocyanate (IPDI) while the more reactive one, Methylene diphenyl diisocyanate (MDI), is used for the shell formation. Based on that strategy microcapsules of different morphologies and sizes were obtained, depending on the agitation conditions, as revealed using SEM and optical microscopy. Selective extraction was performed to determine the amount of the less reactive isocyanate (IPDI) stored inside the capsules through FTIR-ATR spectroscopy and isocyanate titration as well as the stability of IPDI inside the capsules over time. As determined, microcapsules based on Acetyl-modified Novolac resin encapsulated 96 wt% of IPDI monomer; this amount is about five and ten times higher than that encapsulated in MCs based on by Benzyl-modified Novolac resin or unprotected Novolac resin, respectively. At the same time, MCs based on Acetyl-modified Novolac resin were stable, maintaining approximately 80 % of the initial isocyanate content after two months of storage under inert conditions. Finally, the self-healing ability of the microcapsules was tested by adding selected IPDI-loaded microcapsules in waterborne polyurethane dispersions. It was proven that the Acetyl-modified Novolac-based MCs showed efficient healing behavior, in the absence of any catalyst, on the polyurethanes' surfaces when scratched artificially. • Two derivatives of Novolac resin through benzylation and acetylation were prepared • Novolac-based microcapsules (MCs) loaded with isocyanates (IPDI) were synthesized • High IPDI loading and stability has been found for acetyl-modified Novolac MCs • MCs can be well incorporated into waterborne polyurethane films • Acetyl-modified Novolac-based MCs were proved efficient self-healing materials [ABSTRACT FROM AUTHOR]

The aim of the study was to assess the effect of anode materials, namely a carbon nanotube (CNT)-buckypaper and a commercial carbon paper (CP) on the performance of a two-chamber microbial electrolysis cell (MEC), in terms of hydrogen production and main electrochemical characteristics. The experiments were performed using both acetate-based synthetic wastewater and real wastewater, specifically the effluent of a dark fermentative hydrogenogenic reactor (fermentation effluent), using cheese whey (CW) as substrate. The results showed that CP led to higher hydrogen production efficiency and current density compared to the CNT-buckypaper anode, which was attributed to the better colonization of the CP electrode with electroactive microorganisms, due to the negative effects of CNT-based materials on the bacteria metabolism. By using the fermentation effluent as substrate, a two-stage process is developed, where dark fermentation (DF) of CW for hydrogen production occurs in the first step, while the DF effluent is used as substrate in the MEC, in the second step, to further increase hydrogen production. By coupling DF-MEC, a dual environmental benefit is provided, combining sustainable bioenergy generation together with wastewater treatment, a fact that is also reinforced by the toxicity data of the current study. [ABSTRACT FROM AUTHOR]

The effect of different pretreatment approaches based on alkali (NaOH)/hydrogen peroxide (H2O2) on willow sawdust (WS) biomass, in terms of delignification efficiency, structural changes of lignocellulose and subsequent fermentation toward ethanol, was investigated. Bioethanol production was carried out using the conventional yeast Saccharomyces cerevisiae, as well as three non-conventional yeasts strains, i.e., Pichia stipitis, Pachysolen tannophilus, Wickerhamomyces anomalus X19, separately and in co-cultures. The experimental results showed that a two-stage pretreatment approach (NaOH (0.5% w/v) for 24 h and H2O2 (0.5% v/v) for 24 h) led to higher delignification (38.3 ± 0.1%) and saccharification efficiency (31.7 ± 0.3%) and higher ethanol concentration and yield. Monocultures of S. cerevisiae or W. anomalus X19 and co-cultures with P. stipitis exhibited ethanol yields in the range of 11.67 ± 0.21 to 13.81 ± 0.20 g/100 g total solids (TS). When WS was subjected to H2O2 (0.5% v/v) alone for 24 h, the lowest ethanol yields were observed for all yeast strains, due to the minor impact of this treatment on the main chemical and structural WS characteristics. In order to decide which is the best pretreatment approach, a detailed techno-economical assessment is needed, which will take into account the ethanol yields and the minimum processing cost. [ABSTRACT FROM AUTHOR]