Search

Coherent dual-comb spectroscopy (DCS) enables high-resolution measurements at high speeds without the trade-off between resolution and update rate inherent to mechanical delay scanning approaches. However, high system complexity and limited measurement sensitivity remain major challenges for DCS. Here, we address these challenges via a wavelength-tunable dual-comb optical parametric oscillator (OPO) combined with an up-conversion detection method. The OPO is tunable in the short-wave infrared (1300-1670 nm range) and mid-infrared (2700- 5000 nm range) where many molecules have strong absorption bands. Both OPO pump beams are generated in a single spatially-multiplexed laser cavity, while both signal and idler beams are generated in a single spatially-multiplexed OPO cavity. The near-common path of the combs in this new configuration enables comb-line-resolved and aliasing-free measurements in free-running operation. By limiting the instantaneous idler bandwidth to below 1 THz, we obtain a high power per comb line in the mid-infrared of up to 160 $\mu$W. With a novel intra-cavity nonlinear up-conversion scheme based on cross-comb spectroscopy, we leverage these power levels while overcoming the sensitivity limitations of direct mid-infrared detection, leading to a high signal-to-noise ratio (50.2 dB Hz$^{1/2}$) and record-level dual-comb figure of merit (3.5\times 10^8 Hz$^{1/2}$). As a proof of concept, we demonstrate the detection of methane with 2-ppm concentration over 3-m path length. Our results demonstrate a new paradigm for DCS compatible with high-sensitivity and high-resolution measurements over a wide spectral range., Comment: Supplementary Information included

Dual-comb generation from a single laser cavity provides a simple and high-performance solution to time sampling applications. We demonstrate a compact single-cavity dual-comb laser operating at gigahertz repetition rates and high repetition rate differences up to more than 100 kHz with sub-100 fs pulse duration. The single cavity approach leads to passive common noise suppression resulting in ultra-low relative timing jitter and fully resolvable comb lines in free-running operation. We showcase the laser performance with two application demonstrations: (a) time-domain spectroscopy of acetylene in the near-infrared via computational comb line tracking and (b) free-space THz time domain spectroscopy and thickness-measurements via adaptive sampling. For (b) we use efficient state-of the art iron-doped InGaAs photoconductive antennas to generate and detect the THz light. Here we operate these devices with an efficient Yb-based gigahertz repetition rate laser for the first time. One optical comb generates the THz light, while the other probes it via equivalent time sampling. We obtain signal strengths comparable to reference measurements with MHz repetition rate Er-based laser systems while achieving close to 1 GHz spectral resolution (defined by the comb line spacing) and generating THz frequencies up to 3 THz. By carrying out a careful investigation of the noise properties of the laser we confirm that the free-running gigahertz dual-comb oscillator provides a rapid yet highly precise optical delay sweep from a simple setup. Therefore, our approach will be beneficial for high-update rate time sampling and time-domain spectroscopy applications.

Femtosecond dual-comb lasers have revolutionized linear Fourier-domain spectroscopy by offering a rapid motion-free, precise and accurate measurement mode with easy registration of the combs beat note in the RF domain. Extensions of this technique found already application for nonlinear time-resolved spectroscopy within the energy limit available from sources operating at the full oscillator repetition rate. Here, we present a technique based on time filtering of femtosecond frequency combs by pulse gating in a laser amplifier. This gives the required boost to the pulse energy and provides the flexibility to engineer pairs of arbitrarily delayed wavelength-tunable pulses for pump-probe techniques. Using a dual-channel millijoule amplifier, we demonstrate programmable generation of both extremely short, fs, and extremely long (>ns) interpulse delays. A predetermined arbitrarily chosen interpulse delay can be directly realized in each successive amplifier shot, eliminating the massive waiting time required to alter the delay setting by means of an optomechanical line or an asynchronous scan of two free-running oscillators. We confirm the versatility of this delay generation method by measuring chi^(2) cross-correlation and chi^(3) multicomponent population recovery kinetics.

Ultrafast laser systems operating with high-average power in the wavelength range from 1.9 um to 3 um are of interest for a wide range of applications for example in spectroscopy, material processing and as drivers for secondary sources in the XUV spectral region. In this area, laser systems based on holmium-doped gain materials directly emitting at 2.1 um have made significant progress over the past years, however so far only very few results were demonstrated in power-scalable high-power laser geometries. In particular, the thin-disk geometry is promising for directly modelocked oscillators with high average power levels that are comparable to amplifier systems at MHz repetition rate. In this paper, we demonstrate Semiconductor Saturable Absorber Mirror (SESAM) modelocked Ho:YAG thin-disk lasers (TDLs) emitting at 2.1 um wavelength with record-holding performance levels. In our highest average power configuration, we reach 50 W of average power, with 1.13 ps pulses, 2.11 uJ of pulse energy and ~1.9 MW of peak power. To the best of our knowledge, this represents the highest average power, as well as the highest output pulse energy so far demonstrated from a modelocked laser in the 2 um wavelength region. This record performance level was enabled by the recent development of high-power GaSb-based SESAMs with low loss, adapted for high intracavity power and pulse energy. We also explore the limitations in terms of reaching shorter pulse durations at high power with this gain material in the disk geometry and using SESAM modelocking, and present first steps in this direction, with the demonstration of 30 W of output power, with 692 fs pulses in another laser configuration., Comment: 12 pages, 10 figures

Pulse trains emitted from dual-comb systems are designed to have low relative timing jitter, making them useful for many optical measurement techniques such as optical ranging and spectroscopy. However, the characterization of low-jitter dual-comb systems is challenging because it requires measurement techniques with high sensitivity. Motivated by this challenge, we developed a technique based on an optical heterodyne detection approach for measuring the relative timing jitter of two pulse trains. The method is suitable for dual-comb systems with essentially any repetition rate difference. Furthermore, the proposed approach allows for continuous and precise tracking of the sampling rate. To demonstrate the technique, we perform a detailed characterization of a single-mode-diode pumped $\mathrm{Yb:CaF_2}$ dual-comb laser from a free-running polarization-multiplexed cavity. This new laser produces 115 fs pulses at 160 MHz repetition rate, with 130 mW of average power in each comb. The detection noise floor for the relative timing jitter between the two pulse trains reaches $8.0 \times 10^{-7} \, \mathrm{fs}^2/\mathrm{Hz} \; ( \sim 896 \: \mathrm{zs}/\sqrt{\mathrm{Hz}} )$, and the relative root mean square (rms) timing jitter is 13 fs when integrating from 100 Hz to 1 MHz. This performance indicates that the demonstrated laser is highly compatible with practical dual-comb spectroscopy, ranging, and sampling applications. Furthermore, our results show that the relative timing noise measurement technique can characterize dual-comb systems operating in free-running mode or with finite repetition rate differences while providing a sub-attosecond resolution, which was not feasible with any other approach before., Comment: 19 pages, 6 figures, 78 references; typos corrected, layout adjusted

We present a free-running 80-MHz dual-comb polarization-multiplexed solid-state laser which delivers 1.8 W of average power with 110-fs pulse duration per comb. With a high-sensitivity pump-probe setup, we apply this free-running dual-comb laser to picosecond ultrasonic measurements. The ultrasonic signatures in a semiconductor multi-quantum-well structure originating from the quantum wells and superlattice regions are revealed and discussed. We further demonstrate ultrasonic measurements on a thin-film metalized sample and compare these measurements to ones obtained with a pair of locked femtosecond lasers. Our data show that a free-running dual-comb laser is well-suited for picosecond ultrasonic measurements and thus it offers a significant reduction in complexity and cost for this widely adopted non-destructive testing technique.