Search

A turbulence model study was performed to analyze the flow around the Tubercle Leading Edge (TLE) wing. Five turbulence models were selected to evaluate aerodynamic force coefficients and flow mechanism by comparing with existing literature results. The selected models are realizable k-ε, k-ω Shear Stress Transport (SST), (γ−Reθ) SST model, Transition k-kl-ω model and Stress- ω Reynolds Stress Model (RSM). For that purpose, the TLE wing model was developed by using the NACA0021 airfoil profile. The wing model is designed with tubercle wavelength of 0.11c and amplitude of 0.03c. Numerical simulation was performed at chord-based Reynolds number of Rec = 120,000. The Computational Fluid Dynamic (CFD) simulation reveals that among the selected turbulence models, Stress- ω RSM estimated aerodynamic forces (i.e. lift and drag) coefficients closest to that of the experimental values followed by realizable k-ε, (γ−Reθ) SST model, k-ω SST model and k-kl-ω model. However, at a higher angle of attacks i.e. at 16° & 20° k-ω SST model predicted closest drag and lift coefficient to that of the experimental values. Additionally, the critical observation of pressure contour confirmed that at the lower angle of attack Stress- ω RSM predicted strong Leading Edge (LE) suction followed by realizable k-ε, (γ−Reθ)SST model, k-ω SST model and k-kl-ω model. Thus, the superiority of Stress- ω RSM in predicting the aerodynamic force coefficients is shown by the flow behavior. In addition to this pressure contours also confirmed that k-kl-ω model failed to predict tubercled wing aerodynamic performance. At higher angles of attacks k-ω SST model estimated aerodynamic force coefficients closest to that of the experimental values, thus k-ω SST model is used at 16° & 20° AoAs. The observed streamline behavior for different turbulence models showed that the Stress- ω RSM model and k-kl-ω model failed to model flow behavior at higher AoAs, whereas k-ω SST model is a better approach to model separated flows that experience strong flow recirculation zone.

The aim of this study was to examine the best electrode design for the electrocoagulation process with the best removal performance, reduced passivation on the electrode surface, and lower energy consumption requirements for removing Chromium (Cr) and Lead (Pb) from leather tannery effluent. Three different electrodes were compared: non-rotating disk electrode (NRDE), rotating disk electrode (RDE) and rotating disk mesh electrode (RDME). All electrodes were used to observe a reduction in passivation on the electrode surface and its effects on the removal performance of Cr and Pb. The material used for the electrodes was iron. The maximum removal efficiency obtained was Cr = 87.9% and Pb = 97.5% under the following operating conditions: pH = 7, treatment time = 90 min, current density = 6.57 mA/cm², and RPM = 80. The results show that the electrical energy requirement for treating chromium and lead using RDME was 4.5 kWh/m³, which was found to be lower than the energy requirement observed in various other studies for treating tannery effluent. According to the results, RDME shows the highest removal performance with lower specific energy consumption compared to NRDE and RDE. RDME can be efficiently employed at a larger scale for treating leather tannery effluent.

Medium carbon steel is widely consumed by various industrial sectors due to its attractive set of mechanical properties and low cost, but it experiences deterioration when exposed to a corrosive environment. In the present study, Aloe Vera plant extract was studied as a green corrosion inhibitor for medium carbon steel in an acidic medium. The presence of inhibitive compounds in Aloe Vera plant extract was determined by FTIR. Moreover, the inhibition efficiency was determined through gravimetric analysis and electrochemical analysis. The results show that the Aloe Vera plant extract provided inhibition efficiency of more than 90% in both gravimetric and electrochemical analyses. Furthermore, the shift in polarization curves depicts that this plant extract is a mixed type inhibitor acting as an anodic and cathodic inhibitor. Overall, Aloe Vera plant extract provides excellent corrosion inhibition to medium carbon steel in the H2SO4 environment and can be used as a green corrosion inhibitor for mitigating internal corrosion of pipelines and storage tanks.