Search

Purpose: To investigate the antibacterial effects of Terminalia catappa Linn (TCL) leaf extracts at different concentrations and the effects of these extracts used as primers on the long-term adhesive properties of two universal adhesives., Materials and Methods: After extract preparation, the antimicrobial and antibacterial activities of TCL against Streptococcus mutans (UA 159) were assessed in microdilution assays to provide the minimal inhibitory concentration (MIC) and minimal bactericidal concentration (MBC). Additionally, to provide quantitative data on the ability of TCL extract to reduce cell viability, colony forming units (CFU) were counted. To examine adhesive properties, 288 human molars were randomly assigned to 32 experimental conditions (n = 9) according to the following variables: (1) treatment agent: negative control (untreated surface), and primers at concentrations of 1xMIC, 5xMIC, and 10xMIC; (2) adhesives: Scotchbond Universal (SBU) and Futurabond Universal (FBU); (3) adhesive strategy: etch-and-rinse (ER) or self-etch (SE); and (4) storage time: 24 h or after 2 years. Primers were applied for 60 s, upon which the teeth were incrementally restored and sectioned into adhesive-dentin bonded sticks. These were tested for microtensile bond strength (μTBS) and nanoleakage (NL) after 24-h and 2-year water storage, as well as in-situ degree of conversion (DC) at 24 h. The chemical profile of the hybrid layer was determined via micro-Raman spectroscopy. Biofilm assay data were analyzed using the Kruskal-Wallis test; the pH of culture media and the chemical profile were analyzed by one-way ANOVA. The adhesive properties (µTBS, NL, DC) were evaluated using a four-way ANOVA and Tukey's test. Significance was set at 5%., Results: Similar values of MIC and MBC were observed (2 mg/ml), showing bactericidal potential. CFU analysis demonstrated that concentrations of 5xMIC and 10xMIC significantly inhibited biofilm formation (p < 0.001). The application of the TCL primer at all concentrations significantly increased the immediate μTBS and DC, and decreased the immediate NL values when compared to the control group (p < 0.05), regardless of the adhesive and adhesive strategies. Despite an increase in the NL values for all groups after 2 years (p > 0.05), in groups where the TCL primer was applied, the μTBS remained constant after 2 years for both adhesives, while a decrease in the μTBS was observed in the control groups (p < 0.05). Usually, 10xMIC showed better results than 1xMIC and 5xMIC (p < 0.05). The application of TCL promoted cross-linking; cross-linking rates increased proportionally to the concentration of TCL (p < 0.05)., Conclusion: Primers containing TCL promoted bactericidal and bacteriostatic action, as well as cross-linking with dentin, while maintaining the adhesive properties of the adhesive-dentin interface after 2 years of water storage.

Objective: To evaluate the effect of prolonged (P) polymerization time of a universal adhesive system applied in etch-and-rinse (ER) or self-etch (SE) strategies on the clinical performance of restorations in non-carious cervical lesions (NCCLs), after 36 months of clinical service., Methods: A total of 140 restorations were randomly placed in 35 subjects according to the polymerization time groups: ER (10 s); ER-P (40 s); SE (10 s); and SE-P (40 s) at 1,200 mW/cm 2 . Composite resin was placed incrementally. The restorations were evaluated immediately and after 6, 12, 18, and 36 months using the FDI criteria. Data were analyzed using the Kaplan-Meier survival test for retention loss, and the Kruskal-Wallis' test for secondary outcomes (α = 0.05)., Results: After 36 months, 19 restorations were lost: ER 6, ER-P 2, SE 9, SE-P 2. The retention rates were 82.3% for ER; 94.1 % for ER-P; 73.5 % for SE; and 94.1 % for SE-P, with a significant difference between ER vs. ER-P and SE vs. SE-P, as well as ER vs. SE-P and ER-P vs. SE (p < 0.0001). Minor defects were observed in 18 restorations for the marginal staining criteria: ER 5, ER-P 2, SE 8, SE-P 3; and in 33 restorations for the marginal adaptation criteria: ER 11, ER-P 4, SE 12, and SE-P 6 (p > 0.05). No restorations showed recurrence of caries or postoperative sensitivity., Conclusions: A prolonged polymerization time of 40 s improves the clinical performance of the universal adhesive for both adhesive strategies evaluated, even after 36 months., Clinical Significance: Prolonging the polymerization time of a universal adhesive from 10 to 40 s has been shown to improve its clinical performance when used in NCCLs., Competing Interests: Declaration of competing interest Declarations of interest: The authors of the article entitled “Prolonged Polymerization of a Universal Adhesive in Non-Carious Cervical Lesions: 36-month Double-Blind Randomized Clinical Trial” certify that they have NO affiliations with or involvement in any organization or entity with any financial interest (such as honoraria; educational grants; participation in speakers’ bureaus; membership, employment, consultancies, stock ownership, or other equity interest; and expert testimony or patent-licensing arrangements), or non-financial interest (such as personal or professional relationships, affiliations, knowledge or beliefs) in the subject matter or materials discussed in this manuscript., (Copyright © 2023. Published by Elsevier Ltd.)

Objectives: To evaluate the influence of the sonic device on the clinical performance of one-step self-etch adhesive systems in non-carious cervical lesions (NCCLs) after 18 months., Materials and Methods: Forty patients participated in this study. Eighty restorations were assigned to two groups (n = 40): Sonic application and Manual application. After the adhesive application (iBond Self-Etch, Kulzer, Hanau, Germany), NCCLs were restored using composite resin (Charisma, Kulzer, Hanau, Germany). The restorations were evaluated at baseline and after 18 months both according to the Word Dental Federation (FDI) and the United States Public Health Service (USPHS) criteria. Friedman repeated measures analysis of variance by rank and Wilcoxon test for significance in each pair were applied (α = 0.05)., Results: After 18 months, 38 patients were evaluated. Twenty-three restorations were lost (19 for manual vs. 4 for sonic application). The retention rates (95% confidence interval) were 50% (CI 34.8%-65.1%) for manual application and 84.2% (CI 69.6%-92.6%) for sonic application (p < 0.05). Twelve restorations showed marginal staining (nine for manual vs. three for sonic application; FDI, p < 0.05) and nine some marginal discrepancy (seven for manual vs. two for sonic application; FDI, p < 0.05). No restorations showed postoperative sensitivity and caries recurrence at the time., Conclusion: The sonic application increases the retention rate of iBond Self-Etch after 18 months of clinical evaluation in NCCLs., Clinical Relevance: The application of a simplified self-etch adhesive (iBond Self-Etch) associated to a sonic device seems to be an alternative to improve the clinical behavior in NCCLs., (© 2022 Wiley Periodicals LLC.)

Objectives: To develop dual-functional etchants that could demineralize and stabilize dentin collagen simultaneously, and to assess the effects of these etchants on collagen crosslinking, biostability and resin bonding properties under clinically relevant conditions., Methods: Dual-functional etchants were prepared by mixing 56% glycolic acid and 17% phosphoric acid and adding 1% of theaflavins (TF) or proanthocyanidins from grape seed extract (GSE). The etchant without crosslinker was used as control. The prepared human dentin specimens were treated with the 3 etchants for 30 s and analyzed for chemical interaction using Fourier transform infrared spectroscopy and resistance of the demineralized layer to collagenase degradation using electron microscopy (EM). Resin-dentin interfacial bonding properties were evaluated after 24 h and after 10,000 thermocycling through microtensile bond strength (μTBS), nanoleakage and matrix metalloproteinases (MMPs) activity via in situ zymography. Statistical analysis was done using ANOVA and post- hoc Tuckey's test., Results: Compared to control, TF and GSE dual-functional etchants were able to demineralize dentin, induce collagen crosslinking and protect the demineralized layer from collagenase degradation within 30 s. High resolution EM images showed better protection with TF etchant compared to GSE. There was a significant reduction in μTBS and an increase in nanoleakage and MMPs activity in control after thermocycling (p < 0.05) while these changes weren't seen in dual-functional etchants., Significance: Dual-functional etchants, especially TF containing, provide collagen protection against degradation and result in stable μTBS and less nanoleakage and MMPs activity under clinically relevant conditions., (Copyright © 2023 Elsevier Inc. All rights reserved.)

Objective: Sound, natural dentin collagen can be stabilized against enzymatic degradation through exogenous crosslinking treatment for durable bonding; however, the effect on denatured dentin (DD) collagen is unknown. Hence, the ability of different crosslinkers to enhance/restore the properties of DD collagen was assessed., Methods: Demineralized natural and DD collagen films (7 mm × 7 mm × 7 µm) and beams (0.8 mm × 0.8 mm × 7 mm) were prepared. DD collagen was experimentally produced by heat or acid exposure, which was then assessed by various techniques. All specimens were then treated with 1 wt% of chemical crosslinker 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide/n-hydroxysuccinimide (EDC/NHS) and two structurally different flavonoids-theaflavins (TF) from black tea and type-A proanthocyanidins from cranberry juice (CR) for either 30 s or 1 h. The controls were untreated. Dentin films were assessed for chemical interaction and cross-linking effect by FTIR, biostability against exogenous collagenase by weight loss (WL) and hydroxyproline release (HYP), and endogenous matrix metalloproteinases (MMPs) activity by confocal laser microscopy. Dentin beams were evaluated for tensile properties. Data were analyzed using ANOVA and Tukey's test (α = 0.05)., Results: Compared with natural collagen, DD collagen showed pronounced structural changes, altered biostability and decreased mechanical properties, which were then improved to various degrees that were dependent on the crosslinkers used, with EDC/NHS being the least effective. Surprisingly, the well-known MMP inhibitor EDC/NHS showed negligible effect on or even increased MMP activity in DD collagen. As compared with control, cross-linking induced by TF and CR significantly increased collagen biostability (reduced WL and HYP release, p < 0.05), MMP inhibition ( p < 0.001) and mechanical properties ( p < 0.05), regardless of denaturation., Conclusions: DD collagen cannot or can only minimally be stabilized via EDC/NHS crosslinking; however, the challenging substrate of DD collagen can be enhanced or restored using the promising flavonoids TF and CR.

Objectives: This study aimed to evaluate the effect of copper nanoparticles (CuNp) on the clinical performance of a universal adhesive system used as an etch-and-rinse or self-etch strategy., Methods: A total of 216 class V (non-carious lesions) restorations were randomly placed in 36 subjects according to the following groups: ERcu, adhesive in etch-and-rinse with 0.1% CuNp; ERct, adhesive in etch-and-rinse without CuNp; SEcu, adhesive in self-etch with 0.1% CuNp; and Sect, adhesive in self-etch without CuNp. Restorations were evaluated at baseline and at 6, 12, 18, 36, and 48 months, using the FDI and USPHS criteria. Appropriate statistical analyses were performed (α = 0.05)., Results: After 48 months, 14 restorations were lost (two for ERcu, five for SEcu, and seven for SEct) and the retention rates (95% confidence interval [CI]) were 74.1% for ERcu (95% CI 61.1-83.8); 81.5% for ERct (95% CI 69.2-89.6); 64.8% (95% CI 51.5-76.2) for SEcu; and 64.8% (95% CI 51.5-76.2) for SEct, with statistical differences between SEct vs. ERct and SEcu vs. ERct (p < 0.05). No significant differences between the groups were observed when the secondary parameters were evaluated (p > 0.05). Nineteen restorations (two for ERcu, two for ERct, six for SEcu, and nine for SEct) showed minor marginal staining, and 44 restorations (7 for ERcu, 8 for ERct, 14 for SEcu, and 15 for SEct) presented minimal marginal adaptation defects., Significance: This is the first long-term clinical trial to show that the addition of CuNp to a universal adhesive system does not affect clinical performance., (Copyright © 2023 Elsevier Inc. All rights reserved.)

Viral infections are some of the most common sources of respiratory illness in pediatric and adult populations worldwide. Influenza and coronaviruses are viral pathogens that could lead to severe respiratory illness and death. More recently, respiratory illness from coronaviruses, accounts for more than 1 million deaths in the United States alone. This article will explore the epidemiology, pathogenesis, diagnosis, treatment, and prevention of severe acute respiratory syndrome caused by coronavirus-2, and Middle Eastern respiratory syndrome., (© 2023 Elsevier Inc. All rights reserved.)

Objective: To investigate the effects of salivary esterases on biostability of collagen treated by galloylated polyphenols., Methods: Human dentin was microtomed into 6-μm-thick films, which were demineralized and treated for 60 s using solutions containing 0.6% and 2% of one of the crosslinkers: tannic acid (TAC), epigallocatechin gallate (EGCG), epigallocatechin (EGC), and N-[3-dimethylaminopropyl]-N'-ethylcarbodiimide hydrochloride (EDC)/N-hydroxysuccinimide (NHS), and for 1 h using EDC/NHS. Half of the treated and untreated (control) films were subjected to human saliva incubation. Collagen biostability was assessed via exogenous protease biodegradation by weight loss and hydroxyproline release, and endogenous MMPs by in situ zymography. The degradation products of galloylated polyphenols (TAC and EGCG) by saliva were monitored using proton nuclear magnetic resonance ( 1 H NMR) and gel permeation chromatography (GPC). The esterase activity of saliva induced by the crosslinkers was also assessed., Results: Collagen films treated with TAC and EGCG exhibited significantly improved biostability (p < 0.05); however, the enhanced biostability was severely reduced after saliva incubation (p < 0.001). For EDC/NHS treated collagen, saliva incubation showed negligible effect on the biostability. 1 H NMR studies confirmed the esterase-catalyzed hydrolysis of the galloyl. GPC measurements showed decreased molecular weight of TAC in saliva indicating its chemical degradation. Both TAC and EGCG showed much higher esterase activity than other treatment groups., Significance: The galloyl group plays important role in collagen crosslinking, inducing higher biostability. However, galloylated polyphenols crosslinked on collagen are highly susceptible to metabolism of human saliva by salivary esterase, dramatically compromising the enhanced biostability., (Copyright © 2022 Elsevier Inc. All rights reserved.)

Objective: This study aimed to evaluate the effect of prolonging polymerization time on the 18 months clinical performance of a universal adhesive system used as etch-and-rinse (ER) and self-etch (SE)., Methods: 140 restorations were randomly placed in 35 subjects according to the following groups: ER10 (light-curing for 10 s); ER40 (light-curing for 40 s); SE10 (light-curing for 10 s) and; SE40 (light-curing for 40 s/1200 mW/cm 2 ). A resin composite was placed incrementally. The restorations were evaluated at baseline and after 18 months by using the FDI criteria. The following outcomes were evaluated: marginal staining, marginal adaptation, spontaneous post-operative sensitivity and recurrence of caries. The differences among the groups were calculated using Friedman repeated measures analysis of variance rank (α = 0.05)., Results: After 18 months the retention/fracture rates were 88.9% (95%CI 74.1-95.6%) for ER10, 94.3% (95%CI 91.4-98.5%) for ER40, 77.2% (95%CI 60.1-87.9) for SE10 and 97.2% (95%CI 85.5-99.9%) for SE40. A significant difference was detected in the retention rate when SE10 was compared to the SE40 (p = 0.01). Also, ER40 showed a significant improvement of the marginal adaptation when compared to ER10 (p = 0.01)., Significance: This is the first study that demonstrates an improvement in the clinical performance of universal adhesive systems in non-carious cervical lesions when prolonged light-cured was applied., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2021 The Academy of Dental Materials. Published by Elsevier Inc. All rights reserved.)

Objective: To evaluate the effects of different polyphenols and solvents on dentin collagen's crosslinking interactions and biostabilization against MMPs and collagenase degradation., Methods: Two polyphenols [proanthocyanidin (PA) and quercetin (QC)] with different water solubility were prepared as treatment solutions using ethanol (EtOH) or dimethyl sulfoxide (DMSO) as solvents. 6-um-thick dentin films were microtomed from dentin slabs of third molars. Following demineralization, films or slabs were subject to 60-s treatment (PA or QC) or no treatment (control) with subsequent extended-rinse with original solvent (EtOH or DMSO) or distilled water (DW). Collagen crosslinking interactions were assessed by FTIR. Biostability was assessed through endogenous MMPs activity via confocal laser scanning microscopy, and exogenous collagenase degradation via weight loss, hydroxyproline release and SEM. Finally, direct collagenase inactivation was also evaluated. Data were analyzed by three-way ANOVA and post-hoc tests (α=0.05%)., Results: Distinct effects of two polyphenols and solvents on collagen crosslinking and biostabilization were observed. Higher crosslinking and biostability efficacy occurred with PA than QC (p<0.001) that demonstrated negligible collagen interactions. With DMSO solvent, efficacy results were significantly reduced with both polyphenols (p<0.05). DMSO-rinse further weakened interactions of PA with collagen, diminishing biostability (p<0.05). Low biostability was detected with QC and DW-rinse, suggesting direct enzymatic inhibition due to physical presence in collagen., Significance: Collagen crosslinking interactions and biostability depend on polyphenol chemical characteristics. Treatment-solution solvents may affect interactions between polyphenols and collagen, specifically, DMSO showed detrimental effects on collagen crosslinking and biostability and should be used with caution., (Copyright © 2021 The Academy of Dental Materials. Published by Elsevier Inc. All rights reserved.)

Objectives: This systematic review aimed to detect whether acid etching pretreatment would enhance the bond strength of universal adhesives (UAs) to caries-affected dentin before and after aging., Methodology: Two independent researchers reviewed materials published until August 2024 in five databases (Web of Science, PubMed, SciELO, Scopus, Science Direct, and Cochrane Library). The eligibility criteria contained in vitro studies that assessed the bond strength of UAs to caries-affected dentin using etch-and-rinse and self-etch modes, with or without aging. Statistical meta-analysis was performed using inverse variance method by the Review Manager program (p < 0.05)., Results: In total, 26 studies were included in the quantitative analysis. Studies have mostly focused on mild UAs. The application of acid etching did not impact the bond strength of ultra-mild and mild UAs (p > 0.05). Aging considerably reduced the bond strength of mild UAs in etch-and-rinse or self-etch modes (p < 0.05). Bond strength to caries-affected dentin was considerably lower than that to sound dentin in both etching modes (p < 0.05)., Conclusions: Pretreatment with phosphoric acid did not affect the bond strength of mild and ultra-mild UAs to caries-affected dentin. The aging process led to a decrease in the bond strength of mild UAs to caries-affected dentin, irrespective of the application strategy., Competing Interests: Declarations. Competing interests: The authors declare no competing interests. Conflict of interest: The authors declare no commercial or associative interest representing a conflict of interest regarding the manuscript. The authors do not have any financial interests or commercial associations to disclose. Ethical approval: This article does not contain any studies with human participants or animals performed by any of the authors. Informed consent: For this type of study, formal consent is not required., (© 2024. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

A promising approach for managing root caries is the use of cross-linking agents to stabilize collagen. However, despite testing various natural and synthetic agents in vitro, their efficacy remains uncertain. The aim of this review was to examine which cross-linking agent performs better in reducing root caries lesion depth and the release of hydroxyproline, which is a marker of collagen degradation. Studies evaluating the impact of cross-linking agents on dentin were included, while studies performed on enamel surface/cell cultures and studies evaluating collagenase inhibitors were excluded, among others. A comprehensive search covered eight databases, and study quality was assessed using the QUINN Tool for in vitro dental studies. Synthesis of the results was done using a Bayesian network meta-analysis to compare agents. Fifty studies involving 31 cross-linking agents were included for qualitative synthesis. The network meta-analysis for lesion depth involved 284 samples across 36 comparisons and ranked cross-linking agents in terms of their caries lesion depth-reducing effect (from best to worst): naringin > quercetin > riboflavin > proanthocyanidins > hesperidin > glutaraldehyde > cranberry > grape seed extract > untreated controls. Only naringin, quercetin, proanthocyanidins, and glutaraldehyde showed statistically significant efficacy over untreated controls. Cranberry extract excelled in reducing hydroxyproline release, followed by proanthocyanidins. In conclusion, proanthocyanidins positively affected both outcomes, suggesting they are prime candidates for translational research. Clinical studies are now essential to evaluate their real-world effectiveness against root caries. PROSPERO-CRD42023404911., (© 2024 Scandinavian Division of the International Association for Dental Research. Published by John Wiley & Sons Ltd.)

Resveratrol (RV-3, 5, 4'-trihydroxystilbene) is a natural compound found in plants like red grapes, berries, and peanuts, with promising effects on dental health. It helps strengthen tooth enamel by promoting remineralization, making the teeth more resistant to decay caused by acid-producing bacteria. RV also shields dentin, a vulnerable layer beneath the enamel, from erosion and sensitivity. Its anti-inflammatory properties can reduce inflammation associated with dental conditions such as pulpitis and endodontic diseases. Moreover, RV's antimicrobial activity inhibits the growth of bacteria involved in dental plaque and biofilm formation, preventing their accumulation on the tooth surface. This contributes to a healthier oral environment and prolongs the lifespan of dental restorative materials. However, the research on RV's impact on dental health is in its early stages, and further studies are needed to confirm potential benefits. Important factors such as determining the optimal dosage, understanding its bioavailability, and assessing potential side effects require further investigation. This review focuses on the important role of RV in promoting dental health. It delves into various aspects, including its impact on root health, maintenance of the dental pulp, care for tooth enamel, effectiveness of dental restorative materials, and health of dentin., (© 2024. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

This study evaluated the effect on adhesive layer thickness, bond strength, and adhesive failure pattern of the application of universal adhesive (Scotchbond Universal) using either manual or rotary brush in dentin previously impregnated with bioceramic sealer (Sealer Plus BC) using a manual brush, at 24 h and 1 year. Eighty-eight bovine crowns were divided into four groups (n = 22) according to the intervention: (i) use of bioceramic sealer and adhesive application using manual brush, (ii) use of bioceramic sealer and adhesive application using rotary brush, (iii) use of resin sealer and adhesive application using manual brush, and (iv) use of resin sealer and adhesive application using rotary brush. Subsequently, specimens were restored with a composite resin (Filtek Z-250). Adhesive layer thickness was evaluated using confocal microscopy. Bond strength was assessed using the microtensile bond strength test, and adhesive failure pattern was evaluated under a stereomicroscope. Data were analyzed using two-way ANOVA/Tukey tests. Specimens where a rotary brush had been used exhibited lower adhesive layer thickness. Specimens treated with resin sealer and using a manual brush showed lower bond strength values and a higher occurrence of adhesive failures at 24 h and 1 year than specimens treated with bioceramic sealer and using rotary brush for adhesive application., (© 2024 Scandinavian Division of the International Association for Dental Research. Published by John Wiley & Sons Ltd.)

Purpose: To investigate the effect of adhesive type and long-term aging on the shear bond strength (SBS) between silicabased ceramics and composite cement (CC). Materials and Methods: Lithium-silicate (LS), feldspathic (FD) and polymer-infiltrated ceramic (PIC) blocks were sectioned (10 x 12 x 2 mm) and divided into 24 groups considering the factors: "ceramics" (LS, FD, and PIC), "adhesive" (Ctrl: without adhesive; 2SC: 2-step conventional; 3SC: 3-step conventional; 1SU: 1-step universal), and "aging" (non-aged or aged [A]). After the surface treatments, CC cylinders (n = 15, ɸ=2mm; height = 2mm) were made and half of the samples were subjected to thermocycling (10,000) and stored in water at 37°C for 18months. The samples were submitted to SBS testing (100 kgf, 1mm/min) and failure analysis. Extra samples were prepared for microscopic analysis of the adhesive interface. SBS (MPa) data was analyzed by 3-way ANOVA and Tukey's test (5%). Weibull analysis was performed on the SBS data. Results: All factors and interactions were significant for SBS (p<0.05). Before aging, there was no significant difference between the tested groups and the respective control groups. After aging, the LS_1SU (22.18±7.74) and LS_2SC (17.32±5.86) groups exhibited significantly lower SBS than did the LS_Ctrl (30.30±6.11). Only the LS_1SU group showed a significant decrease in SBS after aging vs without aging. The LS_1SU (12.20) group showed the highest Weibull modulus, which was significantly higher than LS_2SC_A (2.82) and LS_1SU_A (3.15) groups. Conclusion: No type of adhesive applied after silane benefitted the long-term adhesion of silica-based ceramics to CC in comparison to the groups without adhesive. [ABSTRACT FROM AUTHOR]

Purpose: To evaluate the effect of urethane methacrylate precursor (UMP) on the enzymatic resistance of demineralized dentin (DD) matrices. Materials and Methods: Experimental treatments containing 0 (control), 1, and 5 mmol/L UMP dissolved in an acetone (Ace) solution were formulated. Dentin matrix specimens were demineralized in vitro and immersed in the experimental treatments for 1 h. The treated specimens were then stored in 0.1 mg/mL collagenase solution for 24 h, after which their dry mass loss and hydroxyproline (HYP) release were assessed. The swelling ratios of specimens in each group were also evaluated. The interaction between UMP and the dentin matrix was observed using field-emission scanning electron microscopy (FE-SEM). Endogenous enzyme activity in dentin was evaluated using confocal laser scanning microscopy (CLSM). Results: Compared with the other treatment groups, treatment with 1 mM and 5 mM UMP-Ace significantly decreased the dry mass loss, HYP release and swelling ratio of the DD matrix (p < 0.05). FE-SEM and CLSM observations showed that treatment with UMP-Ace protected the structure of the dentin matrix and decreased porosity within the dentin-collagen network. Conclusion: Treatment with 1 mM and 5 mM UMP-Ace protects DD matrix against collagenase degradation and may be clinically useful for improving the durability of the hybrid layer. [ABSTRACT FROM AUTHOR]

Purpose: To investigate the antibacterial effects of Terminalia catappa Linn (TCL) leaf extracts at different concentrations and the effects of these extracts used as primers on the long-term adhesive properties of two universal adhesives. Materials and Methods: After extract preparation, the antimicrobial and antibacterial activities of TCL against Streptococcus mutans (UA 159) were assessed in microdilution assays to provide the minimal inhibitory concentration (MIC) and minimal bactericidal concentration (MBC). Additionally, to provide quantitative data on the ability of TCL extract to reduce cell viability, colony forming units (CFU) were counted. To examine adhesive properties, 288 human molars were randomly assigned to 32 experimental conditions (n = 9) according to the following variables: (1) treatment agent: negative control (untreated surface), and primers at concentrations of 1xMIC, 5xMIC, and 10xMIC; (2) adhesives: Scotchbond Universal (SBU) and Futurabond Universal (FBU); (3) adhesive strategy: etch-and-rinse (ER) or self-etch (SE); and (4) storage time: 24 h or after 2 years. Primers were applied for 60 s, upon which the teeth were incrementally restored and sectioned into adhesive-dentin bonded sticks. These were tested for microtensile bond strength (pTBS) and nanoleakage (NL) after 24-h and 2-year water storage, as well as in-situ degree of conversion (DC) at 24 h. The chemical profile of the hybrid layer was determined via micro-Raman spectroscopy. Biofilm assay data were analyzed using the Kruskal-Wallis test; the pH of culture media and the chemical profile were analyzed by one-way ANOVA. The adhesive properties (pTBS, NL, DC) were evaluated using a four-way ANOVA and Tukey's test. Significance was set at 5%. Results: Similar values of MIC and MBC were observed (2 mg/ml), showing bactericidal potential. CFU analysis demonstrated that concentrations of 5xMIC and 10xMIC significantly inhibited biofilm formation (p < 0.001). The application of the TCL primer at all concentrations significantly increased the immediate pTBS and DC, and decreased the immediate NL values when compared to the control group (p < 0.05), regardless of the adhesive and adhesive strategies. Despite an increase in the NLvalues for all groups after2years (p > 0.05), in groups where the TCL primerwas applied, the pTBS remained constant after 2 years for both adhesives, while a decrease in the pTBS was observed in the control groups (p < 0.05). Usually, IOxMIC showed better results than 1xMIC and 5xMIC (p < 0.05). The application of TCL promoted cross-linking; cross-linking rates increased proportionally to the concentration of TCL (p < 0.05). Conclusion: Primers containing TCL promoted bactericidal and bacteriostatic action, as well as cross-linking with dentin, while maintaining the adhesive properties of the adhesive-dentin interface after 2 years of water storage. [ABSTRACT FROM AUTHOR]

Purpose: This study investigated and compared the bond strengths, microleakage, microgaps, and marginal adaptation of self-adhesive resin composites (SAC) to dentin with or without universal adhesives. Materials and Methods: Dentin surfaces of 75 molars were prepared for shear and microtensile bond strength testing (SBS and μTBS). Silicon molds were used to build up direct restorations using the following materials to form 5 groups: 1. Surefil One; 2. Prime&Bond active Universal Adhesive + Surefil One; 3. Vertise Flow; 4. OptiBond Universal + Vertise Flow; 5. Scotchbond Universal + Filtek Z500 (control group). Bonded specimens were thermocycled 10,000x before being tested either for SBS or μTBS using a universal testing machine at a crosshead speed of 0.5mm/min. Direct mesial and distal class-II cavities were created on 100 sound premolars, with the gingival margin of distal cavities placed below CEJ and restored according to the five groups. After thermocycling, microleakage scores were assessed following immersion of restored premolars in 2% methylene blue dye for 24h, while marginal gaps and adaptation percentages were investigated on epoxy resin replicas under SEM at magnifications of 2000X and 200X, respectively. Results were statistically analyzed with parametric and non-parametric tests as applicable, with a level of significance set at a = 0.05. Results: Bond strengths, microleakage scores, microgaps, and percent marginal adaptation of Surefil One and Vertise Flow were significantly (p<0.001) inferior to the control group. Dentin preconditioning with universal adhesives significantly increased the study parameter outcomes of Surefil One and Vertise Flow, yet they were still significantly below the performance of the control group. Conclusion: Conventional resin composite outperformed the SAC whether applied solely or in conjunction with their corresponding universal adhesives. [ABSTRACT FROM AUTHOR]

Objectives: To evaluate the effects of Nd:YAG laser irradiation on the microstructures of dentin surfaces and the long-term bond strength of dentin under simulated pulpal pressure., Materials and Methods: Under simulated pulp pressure, 30 freshly extracted caries-free third molars were cut into 2-mm-thick dentin samples and then divided into five groups: the control and laser groups (93.3 J/cm 2 ; 124.4 J/cm 2 ; 155.5 J/cm 2 ; 186.6 J/cm 2 ). Scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR), and Vickers hardness were used to analyze the surface morphology, composition, and mechanical properties of the dentin before and after laser irradiation. Another 80 caries-free third molars were removed and treated as described above, and the resin was bonded to the dentin surface with Single Bond Universal (SBU) adhesive in self-etch mode to make stick specimens. Microtensile bond strength (µTBS), confocal laser scanning microscopy (CLSM), and interfacial silver nanoleakage tests before and after 10,000 times thermocycling were then performed to analyze the bonding properties and interfacial durability of each group., Results: SEM observations revealed that the surfaces of all laser group specimens were rough with open dentin tubules. Laser irradiation altered the surface composition of dentin while removing some collagen fibers but did not affect its surface hardness or crystallographic characteristics. Furthermore, laser irradiation with an energy density of 124.4 J/cm 2 significantly promoted the immediate and aging bond strengths and reduced nanoleakage compared to those of the control group., Conclusions: Under simulated pulp pressure, Nd:YAG laser pretreatment altered the chemical composition of dentin and improved the immediate and long-term bond strength., Clinical Relevance: This study investigated the optimal parameters for Nd:YAG laser pretreatment of dentin, which has potential as a clinical method to strengthen bonding., (© 2024. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

Objectives: This study aims to assess hydrogen peroxide (HP) penetration within the pulp chamber, color change (CC), physical-chemical properties, and temperature using in-office different concentration bleaching gels with or without violet light., Materials and Methods: Fifty teeth were divided into five groups (n = 10) based on the HP concentration bleaching gels used (6% and 35%) and the used violet light (with or without). HP penetration within the pulp chamber was measured using UV-Vis. The CC was evaluated with a digital spectrophotometer. Initial and final concentration, and pH were measured through titration, and a Digital pHmeter, respectively. Temperature analyses were measured through a thermocouple. Statistical analysis included two-way ANOVA, Tukey's, and Dunnett's test (α = 0.05)., Results: The presence of violet light did not affect the amount of HP within the pulp chamber, or the CC (p > 0.05). Greater penetration of HP was observed within the pulp chamber, as well as CC when using 35% HP (p < 0.05). The final concentration of both gels was lower than the initial concentration, regardless of the use of violet light (p < 0.05). The initial and final pH levels remained neutral and stable (p > 0.05). The pulp temperature increased when the gels were used in conjunction with violet light (p < 0.05)., Conclusions: Using violet light in conjunction with 6% or 35% HP does not alter the physical properties of the bleaching agents, the penetration of HP or enhance color change. However, an increase in temperature was observed when violet light was applied associated with bleaching gels., Clinical Relevance: While the simultaneous use of violet light with hydrogen peroxide 6% or 35% does not alter the material's properties, it also does not bring benefits in reducing hydrogen peroxide penetration and improving color change. Furthermore, the use of violet light increases pulp temperature., (© 2024. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

Background: Obtaining a perfect color match with resin composite presents a significant challenge. The chameleon effect has enabled resin composite to mimic the color of the adjacent tooth structure in vitro. This double-blind, split-mouth and equivalent randomized clinical trial evaluated the color matching of one-shade resin composite with chameleon effect versus multi-shade resin composite in non-carious cervical lesion restorations (NCCLs). Methods: One hundred twenty restorations were performed on NCCLs with two restorative materials (n = 60). After prophylaxis, the teeth were isolated with rubber dam and one universal adhesive was applied in the selective enamel etching strategy. For both groups, the restorations were inserted incrementally. The values of ΔEab and ΔE00 in the cervical and middle third were evaluated using a digital spectrophotometer before vs. after the restorations. The restorations were evaluated at baseline and after 7 days, 6-, 12- and 18-month of clinical performance according to the FDI criteria (Word Federation Criteria). Statistical analysis was performed using Chi-square test for all parameters. Color change was analyzed by two one-sided t-tests for paired samples (α = 0.05). Results: Regarding the color measurement no significant difference was observed when Vittra APS (FGM Dental Products, Joinville, SC, Brazil) was compared to Vittra Unique (FGM Dental Products, Joinville, SC, Brazil) for any of the comparisons performed (p > 0.05). However, the ΔEab and ΔE00 values for the cervical third, both before and after the restorations, were higher compared to the ΔEab and ΔE00 values observed when comparing the cervical and middle thirds after the restorations. After 18 months, five restorations exhibited minimal discrepancies in terms of marginal adaptation or marginal discoloration (p > 0.05). In all other criteria, including retention rate, no changes were detected at the 18-month recall. Conclusions: The one-shade resin composite used achieve the same color match when compared to a multi-shade resin composite after a period of 7 days in NCCLs. Overall, the restorations scored clinically very good (FDI) at baseline and after 18 months for all outcomes. Clinical Significance: The use of a one-shade resin composite in NCCLs can be recommended because it has the ability to simplify the restoration procedure and maintaining an excellent clinical performance. Registration of clinical trials: RBR-8txr4fw: 26/05/2022. [ABSTRACT FROM AUTHOR]

Statement of the Problem: One of the most important factors in the clinical longevity of composite resin restorations is proper adhesion, which is achieved using phosphoric acid. Different phosphoric acid products might affect the micro-shear bond strength of composite resin to enamel. Purpose: The present study aimed to evaluate the micro-shear bond strength of composite resin to sound enamel using six different brands of acid-etch agents. Materials and Method: The present in vitro study was carried out on 72 extracted sound human (mandibular and maxillary) first premolar teeth. The teeth crowns were divided into two equal parts with a mesiodistal cut and randomly assigned to six groups in terms of the acid etchant brand: Ultra-etch, SDI, Morvabon, FGM, Nik Darman, and Experimental. The bonding procedure was carried out using the Margin Bond enamel adhesive. Tygon tubes (1×0.7 mm) containing composite resin were bonded to each enamel surface. After 24 hours of storage in distilled water, each sample underwent a shearing force with a crosshead speed of 0.5 mm/min. The morphologic changes were evaluated using scanning electron microscopy. The data were analyzed with SPSS using one-way ANOVA and Tukey test (p< 0.05). Results: One-way ANOVA showed that micro-shear bond strength in different etchant agents have significant differences (p< 0.001). The highest and lowest composite resin micro-shear bond strengths belonged to Ultradent and SDI brands, respectively. The enamel surfaces in the SDI group revealed residual debris after dissolution. Conclusion: Preparation of the enamel surface with different phosphoric acid products might affect the micro-shear bond strength and enamel surface morphology differently. Further clinical studies are suggested to evaluate the effect of different types and concentrations of acid etching agents on the enamel and dentin bonds. [ABSTRACT FROM AUTHOR]

Purpose: To determine if there was a statistically significant difference between physician assistant (PA) faculty and nurse practitioner (NP) faculty cultural awareness and sensitivity (CAS) and cultural competence behaviors (CCB). Methods: This quantitative comparative analysis utilized the Cultural Competence Assessment (CCA), to measure participants' cultural competence (CC) subscales of CAS and CCB. PA and NP faculty, broadly defined as any PA or NP licensed to practice within a United States jurisdiction and functioning as full- or part-time faculty, adjunct faculty, guest lecturers, or clinical preceptors, participated online. Descriptive statistics were used to generate a depiction of the sample and central tendencies of the CAS and CCB scores. The data were then analyzed using the independent-samples t-test. Results: PA (n = 100) and NP (n = 102) responses were evaluated. For each of the subscales, NP faculty scored marginally higher than their PA counterparts. However, the differences in CAS (P = 0.463) and CCB (P = 0.353) scores failed to achieve statistical significance. The results uncovered that for both groups, CAS scores were higher than CCB scores. This finding may indicate that attitudes and desires regarding diversity and CC are greater than participants' ability or willingness to manifest CC. Conclusion: While there was not a statistically significant difference in the CC scores between PA and NP faculty, there are theoretical and practical implications for employers, NP and PA faculty, NP and PA program administrators, and accrediting organizations for each profession. [ABSTRACT FROM AUTHOR]

Introduction: Achieving strong bond strength of adhesive systems to deep dentin is challenging. Various methods to improve bond strength to deep dentin have been investigated. Chlorhexidine (CHX) enhances the longevity of the bond between adhesives and dentin by inhibiting the collagenolytic activity of Matrix Metalloproteinases (MMPs). Benincasa hispida is a natural plant-based functional food containing minerals and vitamins that help prevent osteoporosis and improve bone health. Aim: To evaluate the Microshear Bond Strength (MSBS) of a 10-methacryloyloxydecyl-dihydrogen Phosphate-based (10-MDP) universal adhesive system to coronal dentin with different dentin surface pretreatments, specifically CHX and Benincasa hispida. Materials and Methods: An in-vitro pilot study was conducted at the Department of Conservative Dentistry and Endodontics, Vishnu Dental College, Bhimavaram, Andhra Pradesh, India, from May 2023 to November 2023. Dentin discs (42) were prepared from human mandibular first molars. A standard etch-and-rinse protocol was performed on the discs. The specimens were assigned to different dentin pretreatments: Group-I (no pretreatment), Group-II (CHX) and Group-III (Benincasa hispida). CHX and Benincasa hispida were applied using micro applicator tips. A dentin bonding agent containing 10-MDP (DBA) was applied, photopolymerised and a composite restoration was fabricated. The MSBS to dentin was evaluated using a universal testing machine. The failure patterns were analysed using a stereomicroscope at 10x magnification. One-way Analysis of Variance (ANOVA) and Tukey's Honestly Significant Difference (HSD) HSD tests were used for statistical analysis, with a significance level set at α=0.05. Results: The mean MSBS values were 24.2732±5.41329 MPa for Group-III, 14.3848±4.23492 MPa for Group-II and 6.9724±3.15837 MPa for Group-I. Pretreatment of dentin with B. hispida resulted in significantly higher MSBS values compared to the other two groups (p<0.001*). Conclusion: Pretreatment with B. hispida significantly improved MSBS. Thus, B. hispida pretreatment may be beneficial in increasing dentin bond strength. [ABSTRACT FROM AUTHOR]

The translation of pre‐clinical anti‐cancer therapies to regulatory approval has been promising, but slower than hoped. While innovative and effective treatments continue to achieve or seek approval, setbacks are often attributed to a lack of efficacy, failure to achieve clinical endpoints, and dose‐limiting toxicities. Successful efforts have been characterized by the development of therapeutics designed to specifically deliver optimal and effective dosing to tumour cells while minimizing off‐target toxicity. Much effort has been devoted to the rational design and application of synthetic nanoparticles to serve as targeted therapeutic delivery vehicles. Several challenges to the successful application of this modality as delivery vehicles include the induction of a protracted immune response that results in their rapid systemic clearance, manufacturing cost, lack of stability, and their biocompatibility. Extracellular vesicles (EVs) are a heterogeneous class of endogenous biologically produced lipid bilayer nanoparticles that mediate intercellular communication by carrying bioactive macromolecules capable of modifying cellular phenotypes to local and distant cells. By genetic, chemical, or metabolic methods, extracellular vesicles (EVs) can be engineered to display targeting moieties on their surface while transporting specific cargo to modulate pathological processes following uptake by target cell populations. This review will survey the types of EVs, their composition and cargoes, strategies employed to increase their targeting, uptake, and cargo release, and their potential as targeted anti‐cancer therapeutic delivery vehicles. [ABSTRACT FROM AUTHOR]

Aim: To evaluate the effect of applying a matrix metalloproteinase (MMP) inhibitor on the fracture resistance of root-filled teeth restored with Everstick fiber-reinforced composite resin. Subjects and Methods: After the selection of 60 freshly extracted human mandibular first molar, root canal access and standard uniformly sized mesio-occluso-distal (MOD) cavities were made and the teeth were randomly assigned into three groups (n = 20 each): Group I, the MOD cavity was first lined with flowable composite resin and then restored with composite resin. In Group II, Everstick fiber was placed into the bed of flowable composite in buccal–pulpal–lingual direction before the composite restoration was placed. In Group III, after etching of the cavity, a 2% chlorhexidine MMP inhibitor was applied. Then, the MOD cavity was restored same as group II. A universal testing machine was employed to compressively load the teeth at a cross-head speed of 0.5 mm/min till fracture. The maximum fracture loads were recorded in Newtons (N) and data were analyzed with one-way ANOVA and post-hoc Tukey tests. Results: Group III exhibited significantly higher fracture resistance compared to all other groups (P < 0.001), whereas Group I demonstrated the lowest fracture resistance. Conclusion: The utilization of Everstick glass fiber, combined with MMP inhibitor treatment, yielded the greatest fracture resistance. Hence, this method may be prioritized over conventional restoration techniques for strengthening root canal-treated teeth with structurally compromised crowns. [ABSTRACT FROM AUTHOR]

Objective: The objective of this study was to evaluate the effect of different surface treatment methods on the shear bond strength (SBS) of metal brackets bonded to two types of CAD/CAM composite restorations: milled and 3D-printed. Materials and Methods: A total of 160 flat-shaped specimens (10 × 10 × 2 mm3) were prepared from four different CAD/CAM composites; two milled (Lava Ultimate™ [LU] and Grandio™ [GR]) and two 3D-printed (Crowntec™ [CT] and C&B Permanent™ [CB]). These specimens underwent thermocycling (5000 cycles at 5–55 °C), then were categorized based on the surface treatment into four groups (n = 10): Group C (control, no surface treatment), Group HF (treated with 9.6% hydrofluoric acid), Group DB (mechanical roughening by a diamond bur), and Group SB (sandblasting using aluminum oxide). Metal brackets were bonded using Transbond XT Primer and universal adhesive, stored in artificial saliva for 24 h, then thermocycled again. Shear bond strength (SBS) was tested using a universal testing machine until bracket debonding occurred. The adhesive remnant index (ARI) was assessed using a stereomicroscope to quantify the residual adhesive following debonding. Result: Regarding material, GR and LU restorations had significantly higher SBS values compared to CT and CB, ranging from 13.90 MPa to 20.35 MPa. Regarding surface treatment, SB and HF groups showed significantly higher SBS values. The ARI scores showed different adhesive modes of failure, with higher instances of scores 0 and 1, which indicate no or minimal adhesive remaining. Conclusions: Both milled and 3D-printed materials had adequate SBS for clinical use, with milled materials showing superior results. Surface treatments like sandblasting and HF significantly improved bond strength, with adhesive failure being common. [ABSTRACT FROM AUTHOR]

The aim of this study is to present the characteristics and a comparison of four different commercial materials dedicated to the CAD/CAM technique in dentistry, all of which can be classified as ceramic materials. Its purpose is also to evaluate the impact of surface treatment on the cytotoxicity and microbiological properties of the materials. The CAD/CAM technique has a perpetually growing role in modern reconstructive dentistry. It requires a material's possession of peculiar characteristics, such as mechanical resistance, durability, functionality (similar to natural tissues), good aesthetics and biocompatibility. To critically evaluate a biomaterial, both manufacturer claims and in vitro tests should be considered. Further steps of evaluation may include animal tests and clinical trials. There are certain attributes of biomaterials that may be modified by surface treatment that can be crucial to the clinical success of the material. The evaluated materials were Vita Suprinity (VITA-Zahnfabrik, Germany), Vita Mark II (VITA-Zahnfabrik, Germany), Celtra Duo (Dentsply Sirona, USA) and Empress Cad (Ivoclar Vivadent, Liechtenstein). They are available in the form of prefabricated blocks of various diameters and are popular among operators performing clinical procedures using CAD/CAM. Standardized blocks of each material were prepared. Half of them had their surface polished. Further, half of all the samples were covered by a nano-copper layer. The samples were evaluated for cytotoxicity, presented on a 0–4 scale, adhesion susceptibility and potential of forming a biofilm on their surface. Physicochemical properties such as the water contact angle (WCA) were evaluated for the tested materials. The influence of copper coating on cytotoxicity cannot be unequivocally stated or denied. Surface polishing did not affect the materials' cytotoxicity, but it increased the WCA of all materials and, therefore, their hydrophobicity. Different degrees of adhesion ability and biofilm formation were dependent on the species of microorganisms and properties of the dental materials. [ABSTRACT FROM AUTHOR]

Copyright of GeSec: Revista de Gestao e Secretariado is the property of Sindicato das Secretarias e Secretarios do Estado de Sao Paulo (SINSESP) and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Background: This study aims to evaluate the microtensile bond strength (µTBS) of different resin composite restorations bonded to mid-coronal dentin and proximal root dentin using light-cured, chemical-cured, and dual-cured adhesives immediately and after aging. Nanoleakage and degree of cure were also assessed. Methods: Eighty-four molars were divided into mid-coronal dentin and proximal root dentin. Each group was further subdivided into three subgroups based on the restorative systems used, which involved the utilization of light-cured, chemical-cured, and dual-cured adhesives. Half of the specimens underwent µTBS testing after 24 h, while the other half after aging. Representative specimens were analyzed for nanoleakage. The degree of cure of the tested adhesive systems was also assessed. Results: Aging showed a significant negative effect on µTBS results and led to increased nanoleakage (p < 0.001). Furthermore, in all subgroups, the µTBS values of proximal root dentin were lower compared to mid-coronal dentin, except in the aged subgroup for the system utilizing the dual-cured adhesive. The restorative systems with chemical and dual-cured adhesives demonstrated comparable bonding properties. However, the system with the light-cured adhesive exhibited the worst bonding properties after aging when bonded to proximal root dentin and cured at a large distance (p < 0.05). Conclusions: All tested restorative systems were negatively affected by aging, and the regional dentin had variable effects on the bonding properties. Clinicians should exercise caution when using the tested light-cured adhesive in areas where the curing distance exceeds 3 mm. [ABSTRACT FROM AUTHOR]

We study a discrete-time interacting particle system with continuous state space, which is motivated by a mathematical model for turnover through branching in actin filament networks. It gives rise to transient clusters reminiscent of actin filament assemblies in the cortex of living cells. We reformulate the process in terms of the inter-particle distances and characterize their marginal and joint distributions. We construct a recurrence relation for the associated characteristic functions and pass to the large population limit, reminiscent of the Fleming-Viot super processes. The precise characterization of all marginal distributions established in this work opens the way to a detailed analysis of cluster dynamics. We also obtain a recurrence relation that enables us to compute the moments of the asymptotic single particle distribution characterizing the transient aggregates. Our results indicate that aggregates have a fat-tailed distribution. [ABSTRACT FROM AUTHOR]

This article comprehensively reviews the performance of simplified direct restorative materials that have the potential to be an alternative to amalgam. Following an understanding of the material structures and clinical performances, this review provides an analysis of the bonding mechanisms and influential factors on the bond strength. These factors include substrate-related variations, involving primary vs. permanent dentin, sound- vs. caries-affected/demineralized dentin comparisons and surface-related factors and pretreatments. Special attention is given to the factors changing the substrate surface, such as different contaminants, remedy methods after contamination and different conditioning methods related to the materials. Variations in sample preparation and bond strength test parameters are also evaluated for the analysis of the outcomes. This review aims to provide an overview of the factors involved in the application procedure of direct restorations together with in vitro testing variations to guide the selection of suitable materials by understanding strengths and shortcomings. [ABSTRACT FROM AUTHOR]

Aim: The purpose of this study was to evaluate the 18-month retrospective study of self-etch adhesive (Prime&Bond One Select) and self-etch mode of universal adhesives (Single Bond Universal, Gluma Bond Universal) applied to non-carious cervical lesions according to the World Dental Federation criteria., Materials and Methods: Thirty patients without any systemic disease, good oral hygiene, having at least 20 teeth and six non-carious cervical lesions treated using a self-etch mode of adhesives operated between January and March 2017. Accordingly, 335 restorations were evaluated according to the World Dental Federation criteria at 3, 6, 12 and 18 months. Pillai's Trace test was used to determine the interaction of criteria with time and adhesive systems. IBM SPSS Statistics 21.0 program was used in the analysis. Value of P < 0.05 was accepted as a criterion for statistical significance., Results: At the end of 18 months, participation was 100%. There was a statistically significant difference P < 0.05 between Prime&Bond One Select and Single Bond Universal, Prime&Bond One Select and Gluma Bond Universal in the 18-month period. In terms of marginal staining, fracture of material and retention, recurrence of caries, erosion and abfraction, tooth integrity criteria at the end of the 18 months, Prime&Bond One Select performed clinically very good, Single Bond Universal and Gluma Bond Universal performed clinically good according to World Dental Federation criteria. Marginal adaptation criteria, Prime&Bond One Select, Single Bond Universal and Gluma Bond Universal performed clinically good. Retention loss rate was found to be the lowest in Prime&Bond One Select and the highest in Gluma Bond Universal., Conclusion: Accordingly, 18-month evaluation of all adhesives used in the study showed clinically acceptable results in all of the World Dental Federation criteria., (© 2023 Australian Dental Association.)

Purpose: To evaluate different protocols for recementation of dislodged glass fiber posts (GFPs).Materials and Methods: The root canals of 50 bovine incisors were prepared to receive GFPs, which were conditioned with 24% hydrogen peroxide, silanized, and cemented with a self-adhesive resin cement. After light curing, the specimens were submitted to a pullout test. The dislodged GPFs were distributed into five experimental groups (n = 10 each) according to surface treatment for recementation: NT = no treatment; SI = silane; ET = 92.8% ethanol/silane; HP = 24% hydrogen peroxide/silane; AL = airborne-particle abrasion (50-μm alumina)/silane. The GFPs were recemented with the same self-adhesive resin cement, and specimens were submitted to a second pullout test. Data were analyzed by Student t test and one-way ANOVA (α = .05).Results: For all groups, the recementation bond strength was higher than the strength obtained after the first cementation (P < .05). There were no statistical differences among the experimental recementation protocols (P = .096).Conclusion: All recementation protocols might be reliably applied since they led to higher bond strength than the first cementation. [ABSTRACT FROM AUTHOR]

This study aimed to assess the efficacy of phototherapy with an Er, Cr:YSGG laser on the bond strength of dentin using two different adhesive systems after chlorhexidine (CHX) application. Twenty-four non-carious human molar teeth were separated into three main groups: negative control Group A (Group A), CHX and phototherapy with an Er, Cr:YSGG laser (Group PC), and CHX with conventional diamond bur (no phototherapy) (Group C). These groups were divided into two subgroups based on adhesives: Clearfil Universal Quick Bond and Clearfil SE Bond. To evaluate the microtensile bond strength, the occlusal enamel surfaces of the teeth were removed with a low-speed, water-cooled diamond bur to expose hard dentin tissue. The teeth within Group PC were treated with Er, Cr:YSGG phototherapy. The surfaces were then disinfected with 0.2% chlorhexidine gluconate. Subgroups were applied according to the manufacturer's instructions using the adhesive systems mentioned above. Following adhesive application, the teeth were restored with composite resin. A microtensile bond strength test was performed on the test sticks obtained from the teeth using a universal test device. Data were analyzed using variance analysis (ANOVA) at a significance level of p < 0.05. Among all groups, the highest bond strength was achieved with Clearfil SE Bond with CHX + phototherapy (45.6 ± 4.2), while the lowest was achieved with Clearfil Universal Quick Bond without phototherapy (control group) (27.0 ± 6.7) (p < 0.05). Phototherapy with Er, Cr: YSGG following chlorhexidine application enhanced the bond strength of both the bond systems (p < 0.05)., (© 2023. The Author(s), under exclusive licence to Springer-Verlag London Ltd., part of Springer Nature.)

Objective: This study aims to evaluate the effects of exposure time and irradiance on the dentin bonding properties (microtensile bond strength (μTBS) and nanoleakage (NL)) of the Clearfil Universal Bond Quick (CUQ) adhesive and Scotchbond Universal Adhesive (SBU) immediately and after 2 years of water storage., Material and Methods: Hence, 128 human molars were randomly assigned to 16 groups based on adhesive strategy, irradiance/exposure times, and storage time for each universal adhesive tested. The adhesives were applied using the etch-and-rinse and self-etch strategies and were light-cured using four different irradiance/exposure times: 1400 mW/cm 2 for 5 s (1400 × 5), 1400 mW/cm 2 for 10 s (1400 × 10), 3200 mW/cm 2 for 5 s (3200 × 5), and 3200 mW/cm 2 for 10 s (3200 × 10). Then, each sample was restored and sectioned into a resin-dentin bonded stick to be tested for μTBS and NL (immediately and after 2 years of water storage). The mean μTBS and NL of all resin-dentin bonded sticks from the same hemi-tooth (factor time) were statistically analyzed using a three-way ANOVA and Tukey's test (a = 0.05)., Results: Despite a significant decrease in the μTBS values for all groups after 2 years of water storage, the 3200 × 5 group showed higher μTBS values, whereas the 3200 × 10 group showed lower μTBS values for both universal adhesives tested. Although a significant increase in the NL values was observed for all groups after 2 years of water storage, the 3200 × 10 group showed higher NL values than the other groups (p < 0.001)., Conclusion: Results indicate that light-curing the adhesive layer with 14-16 J/cm 2 led to an improvement in the stability of the resin-dentin adhesive interface. A longer exposure time (10 s) coupled with a higher irradiance (3200 mW/cm 2 ) resulted in a greater degree of degradation of the adhesive interface., Clinical Significance: To guarantee better stability of the adhesive interface, clinicians could be preferred a light-cured universal adhesive layer with 14-16 J/cm 2 . Higher irradiances should be avoided., (© 2023. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

The central aim of adhesive dentistry is to improve the compatibility between current adhesives and a range of substrates by employing diverse application techniques. Therefore, the overarching objective of this review is to offer a comprehensive analysis of dentin bonding systems, starting with an introduction to adhesion and a detailed overview of enamel and dentin structures, their histology, and the impact of dentin structure on resin–dentin bonding. It covers the mechanisms of resin–dentin bonding, including resin adhesive application, bonding mechanisms, and factors influencing efficacy. Further, this review explores the composition of resin adhesive systems, including acidic components, cross-linking monomers, solvents, and other critical elements. It also examines various adhesive strategies—etch-and-rinse, self-etch, and universal adhesives—highlighting their applications and advantages. The review extends to clinical applications of dental adhesion, including direct restorations, indirect restorations, and immediate dentin sealing (IDS), demonstrating the practical implications of adhesive systems in enhancing restoration longevity and performance. In conclusion, despite significant advancements, no gold-standard method for optimal adhesion exists. Each adhesive system has distinct strengths and limitations. The review emphasizes the importance of evaluating methods for achieving durable adhesion and staying current with technological advancements in adhesive systems. Summary: This review provides a thorough analysis of dentin bonding systems, delving into the structures and bonding mechanisms of both enamel and dentin. By exploring various adhesive systems and their components, it highlights the ongoing challenges in achieving optimal resin–dentin adhesion. The review also addresses the clinical applications of dental adhesion, including direct restorations, indirect restorations, and immediate dentin sealing (IDS), illustrating how different adhesive techniques impact clinical outcomes. It underscores the necessity for continuous innovation and assessment of adhesive systems to enhance long-term bonding effectiveness in clinical practice. [ABSTRACT FROM AUTHOR]

Background and Aims: The bond strength of direct composite restoration to the caries affected dentin is a challenging issue. Preparation of dentin with an antibacterial agent is a method for creating durable bonded restorations. The aim of this study was to investigate the effect of curcumin photosensitizer on the bond strength of a universal adhesive to the caries-affected dentin (CAD). Materials and Methods: In this experimental in vitro study, forty-four decayed human molar teeth were selected. After removing the surface enamel and dentin by a water-cooled saw, the decayed mid-coronal dentin was stained with a caries detection solution. The green and soft infected dentin was removed and CAD and hard and healthy surrounding dentin were left. Then, the remaining dentin surfaces were treated by 600 grit silicon carbide papers and polished. The specimens were divided into two groups (n=22): dentin pretreatment group by curcumin and control with no dentin pretreatment group by curcumin. Each group was divided into two subgroups based on the method of application of All-Bond Universal adhesive (Bisco, USA) (etch and rinseand self-etching methods). After placing the Aelite All Purpose Body (Bisco, USA) composite, all specimens were placed in a universal testing machine for microshear bond strength (µSBS) test. The failure mode of the isolated surfaces was evaluated under a stereomicroscope. Two-way ANOVA analysis was used for statistical analysis. Results: Based on the obtained results, intervention with the adhesive application method and surface pretreatment with curcumin had no significant effect on the bond strength. Also, there was no significant difference in the bond strength of the curcumin group in both etch and rinse and self-etching methods (SE=56.3±27.11 MPa; ER=52.4±84.11 MPa) (P=0.847). In the curcumin-free group, there was no significant difference between the two different adhesive application methods (P=0.187). Conclusion: The results obtained in the present study showed that the pretreatment of dentin affected by caries with light-sensitive curcumin and also use of a universal adhesive by either self-etching or self-etchinf methods had no influence on the microshear bond strength of the composite restoration. [ABSTRACT FROM AUTHOR]

Prior research has indicated that bisphosphonates (BPs) can improve periodontal disease because of their anti-osteoporosis properties. In vitro studies have shown that BPs induce cytotoxicity, inhibit wound healing, and thus affect periodontal disease. Denosumab and BPs have alternative indications. BP and denosumab are not known to correlate with gingival disorders. We assessed such a relationship by applying Bayesian and nonproportional analyses to data in the US FDA Adverse Event Reporting System (FAERS) database. The study analyzed BPs and denosumab-reported incidents with preferred terms found in the narrow Standardized MedDRA Queries for gingival disorders. A total of 5863 reported cases of gingival disorders were associated with five BPs (alendronate, pamidronate, ibandronate, risedronate, and zoledronate) and denosumab. More than 15% of patients with gingival disorders related to BPs and denosumab other than denosumab were hospitalized over short- or long-term periods. Our findings indicated BPs and denosumab had significant reporting odds ratios (ROR), proportional reporting ratios (PRR), and information components (IC) with respect to gingival disorders. Pamidronate had the highest association (ROR = 64.58, PRR = 57.99, IC = 5.71), while the weakest association was found with denosumab (ROR = 3.61, PRR = 3.60, IC = 1.77). Significant associations were found between the six drugs and gingival pain, gingival recession, gingivitis, periodontal disease, and periodontitis. In conclusion, our comprehensive overview of the correlations, clinical characteristics, and prognoses of BPs and denosumab-related gingival disorders suggests that these issues deserve continued surveillance and appropriate management. [ABSTRACT FROM AUTHOR]

The objectives of this study were to evaluate the bonding durability of four different self-etch adhesives to dentin after 24 h and thermal cycling (TC) and to measure the degree of polymerization conversion (DC) in situ. Two-step self-etch adhesives, Clearfil SE Bond 2 (SE2, Kuraray Noritake Dental) and G2-Bond Universal (G2B, GC), and one-step self-etch adhesives, Scotchbond™ Universal Plus Adhesive (SBU, 3M ESPE) and Clearfil Universal Bond Quick (UBQ, Kuraray Noritake Dental), were used. The labial surfaces of bovine teeth were ground to create flat dentin surfaces. The adhesives were applied according to the manufacturers' instructions. After resin composite buildup and 24 h water storage, the specimens were sectioned into beams and all groups were subjected to thermal stress for 0, 10,000 (10k), or 20,000 (20k) cycles followed by micro-tensile bond strength (µTBS) testing. In situ DC was investigated with a laser Raman microscope. The µTBS data were statistically analyzed and subjected to a Weibull analysis. The different groups were compared at the characteristic strength (63.2% probability of failure) (α = 0.05). Two-Way ANOVA was used to show the effect of different adhesives and thermal cycling on the mean DC% followed by Tukey's multiple comparison post hoc test. G2B/TC10k resulted in a significant increase in the µTBS compared to TC0. SBU/TC20k showed significantly higher µTBS compared to TC0. For comparison between different tested adhesives, SBU showed a significantly lower µTBS compared to G2B after TC10k. G2B and SBU showed a greater number of adhesive failures after TC. Mean DC% was different for each adhesive. The newly developed MDP- and HEMA-free 2-SEA showed similar bonding performance with the gold-standard 2-SEA. However, there is still room for further improvement in terms of SEAs. [ABSTRACT FROM AUTHOR]

Fucosterols have been widely studied for their antioxidant, anticancer, and anti-inflammatory properties. However, they have not yet been studied in the field of dentistry. This study aimed to determine whether pretreatment of dentin with fucosterol before resin restoration enhances bond stability in resin-dentin hybrid layers. After applying 0.1, 0.5, and 1.0 wt% fucosterol to demineralized dentin, microtensile bond strength (MTBS) and nanoleakage tests were performed before and after collagenase aging, and the surface was observed using scanning electron microscope (SEM). The fucosterol-treated group showed better bond strength and less nanoleakage both before and after collagenase aging, and the corresponding structures were confirmed using SEM. MMP zymography confirmed that the activity of MMPs was relatively low along the concentration gradient of fucosterol, and the FTIR analysis confirmed the production of collagen crosslinks. In addition, fucosterol exhibits cytotoxicity against Streptococcus mutans, the main cause of dental decay. The results of this study suggest that fucosterol pretreatment improves bond strength and reduces nanoleakage at the resin-dentin interface, possibly through a mechanism involving collagen cross-link formation via the inhibition of endogenous and exogenous MMP activity. This study demonstrates the potential of fucosterol as an MMP inhibitor in dentin, which contributes to long-term resin-dentin bond stability and can be used as a restorative material. [ABSTRACT FROM AUTHOR]

Objective: This systematic review evaluated how different storage times and conditions affect universal adhesives' bond strength and degree of conversion (DC). Methods: A literature search was conducted in PubMed, Scopus, Web of Science, and Google Scholar databases for articles published from January 1st, 2000, until May 15th, 2022. The researchers comprehensively evaluated the articles using a multi-step process to identify articles relevant to the topic of interest. Quality assessment was performed through the ROBDEMAT tool. Due to the high heterogeneity in the preliminary data, performing a meta-analysis was not feasible. Results: A total of 3169 records were obtained, and after removing duplicates, 2267 remained. Following title and abstract screening, 2253 studies were excluded based on the predetermined exclusion criteria. Of the 14 remaining studies, seven were further excluded due to the use of non-universal adhesives, experimental adhesives, or lack of aging protocols. Ultimately, seven studies were included in this systematic review. All studies focused on bond strength, with only one addressing DC. The Findings showed that aging or different storage conditions generally led to reduced bond strength and DC values in universal adhesives, although exceptions with stable or improved properties were noted. Conclusions: Adhesives with higher pH and those containing methacrylamides, HEMA-free compositions, or hydrolytically stable monomers showed better durability than others. Strict adherence to storage instructions, lower storage temperatures, and immediate recapping of adhesive bottles after use is recommended to maintain adhesive properties. These findings provide insights for optimizing the long-term performance of universal adhesives in clinical settings. [ABSTRACT FROM AUTHOR]