Search

The introduction of selective area growth (SAG) in a mature semi‐insulating buried heterostructure (SIBH) platform for the realization of photonic integrated circuits on monolithic InP has been demonstrated. A thorough determination of the relations between quantum well thickness, transition energies, and mask geometries is performed on dedicated wafers by means of extensive micro‐X‐Ray diffraction and microphotoluminescence measurements. Based on those results, SAG is used to grow, with a single epitaxy step, AlGaInAs multiple quantum wells heterostructures, to tailor the active regions of Fabry–Pérot and distributed feedback (DFB) lasers emitting in the O‐Band. SIBH DFB lasers are realized, exhibiting threshold currents < 7.2 mA (at 25 °C), and emitting over 100‐nm spectral range in the O‐Band. [ABSTRACT FROM AUTHOR]

The integration of III-V multi-junction solar cells on Si substrates is currently one of the most promising possibilities to combine high photovoltaic performance with a reduction of the manufacturing costs. In this work, we propose a prospective study for the realization of an InP/InGaAs tandem solar cell lattice-matched to InP on a commercially available Si template by direct MOVPE growth. The InP top cell and the InGaAs bottom cell were firstly separately grown and optimized using InP substrates, which exhibited conversion efficiencies of 13.5% and 11.4%, respectively. The two devices were then combined in a tandem device by introducing an intermediate InP/AlInAs lattice-matched tunnel junction, showing an efficiency of 18.4%. As an intermediate step towards the realization of the tandem device on Si, the InP and InGaAs single junction solar cells were grown on top of a commercial InP/GaP/Si template. This transitional stage enabled to isolate and evaluate the effects of the growth of III-V on Si on the photovoltaic performance through the comparison with the aforementioned devices on InP. Each cell was electrically characterized by external quantum efficiency and dark and illuminated current-voltage under solar simulator. The material quality was also analyzed by means of X-ray diffraction, Atomic-Force Microscopy, Transmission Electron and Scanning Electron Microscopy. The III-V on Si devices showed efficiencies of 3.6% and 2.0% for the InP and InGaAs solar cells, respectively.

Solar cells are complex devices, being constituted of many layers and interfaces. The study and the comprehension of the mechanisms that take place at the interfaces is crucial for efficiency improvement. This paper applies Kelvin probe force microscopy (KPFM) to study materials and interfaces with nanometer scale imaging of the surface potential in the dark and under illumination. KPFM measurements are highly sensitive to surface states and to the experimental measurement environment influencing the atomic probe operating conditions. Therefore, in order to develop a quantitative understanding of KPFM measurements, we have prepared a dedicated structured sample with alternating layers of InP:S and InP:Fe whose doping densities were determined by secondary-ion mass spectroscopy. We have performed KPFM measurements and shown that we can spatially resolve 20 nm thick InP layers, notably when performed under illumination which is well-known to reduce the surface band-bending.

Featured Application: Compact lasers integrated onto SOI for optical communications. The tremendous demand for low-cost, low-consumption and high-capacity optical transmitters in data centers challenges the current InP-photonics platform. The use of silicon (Si) photonics platform to fabricate photonic integrated circuits (PICs) is a promising approach for low-cost large-scale fabrication considering the CMOS-technology maturity and scalability. However, Si itself cannot provide an efficient emitting light source due to its indirect bandgap. Therefore, the integration of III-V semiconductors on Si wafers allows us to benefit from the III-V emitting properties combined with benefits offered by the Si photonics platform. Direct epitaxy of InP-based materials on 300 mm Si wafers is the most promising approach to reduce the costs. However, the differences between InP and Si in terms of lattice mismatch, thermal coefficients and polarity inducing defects are challenging issues to overcome. III-V/Si hetero-integration platform by wafer-bonding is the most mature integration scheme. However, no additional epitaxial regrowth steps are implemented after the bonding step. Considering the much larger epitaxial toolkit available in the conventional monolithic InP platform, where several epitaxial steps are often implemented, this represents a significant limitation. In this paper, we review an advanced integration scheme of AlGaInAs-based laser sources on Si wafers by bonding a thin InP seed on which further regrowth steps are implemented. A 3 µm-thick AlGaInAs-based MutiQuantum Wells (MQW) laser structure was grown onto on InP-SiO2/Si (InPoSi) wafer and compared to the same structure grown on InP wafer as a reference. The 400 ppm thermal strain on the structure grown on InPoSi, induced by the difference of coefficient of thermal expansion between InP and Si, was assessed at growth temperature. We also showed that this structure demonstrates laser performance similar to the ones obtained for the same structure grown on InP. Therefore, no material degradation was observed in spite of the thermal strain. Then, we developed the Selective Area Growth (SAG) technique to grow multi-wavelength laser sources from a single growth step on InPoSi. A 155 nm-wide spectral range from 1515 nm to 1670 nm was achieved. Furthermore, an AlGaInAs MQW-based laser source was successfully grown on InP-SOI wafers and efficiently coupled to Si-photonic DBR cavities. Altogether, the regrowth on InP-SOI wafers holds great promises to combine the best from the III-V monolithic platform combined with the possibilities offered by the Si photonics circuitry via efficient light-coupling. [ABSTRACT FROM AUTHOR]