Search

A passive cavitation detection setup is used to assess and verify the capability of frequency- and amplitudemodulated ultrasound burst signals on the generation of inertial cavitation. The measurements were conducted with a flowthrough tissue-mimicking phantom with a canal of dc = 1mm in diameter simulating a fine blood vessel. By means of a flow velocity of vf= 50mm/s circulating blood in the cardiovascular system is imitated. Applying signal frequencies from f = 550 − 950 kHz and peak rarefaction pressures in a range from ˆpPRFP ≈ 0.17 − 1.81 MPa, various ultrasound stimuli with alternating signal parameters were investigated in the absence and presence of a talcum-water mixture acting as cavitation nuclei. By evaluating the broadband emissions in the frequency domain and calculating the voltage spectral density Srm, the results can be compared. The findings of the present study demonstrate that each ultrasound stimulus triggers a similar strength of cavitation noise at the same Mechanical Index, representing a certain pressure. Over the whole frequency and Mechanical Index (pressure) range, each ultrasound signal type generates a voltage spectral density from Srm= 0.25 − 2.25 V/ √ Hz.

Diflapolin is a dual FLAP/sEH inhibitor with potent anti-inflammatory efficiency in cellular assays and experimental in vivo studies. Despite these outstanding characteristics, its high lipophilicity and plasma protein binding hamper the bioactivity in blood. To overcome these limitations, diflapolin was encapsulated in poly(lactic-co-glycolic acid) nanoparticles to develop an efficient and biocompatible drug delivery system. Two different cosolvent approaches were tested showing the possibility to exchange dimethyl sulfoxide in the organic phase by the sustainable 400 g/mol poly(ethylene glycol). A particle size of 220 nm and the amorphous encapsulation of diflapolin in high amounts rendered the nanoparticles appropriate for the intended application. Excellent biocompatibility of the nanoparticles was demonstrated in an ex ovo hen's egg model. The potent suppression of FLAP-dependent 5-lipoxygenase product formation by the nanoparticles in human whole blood, superior to the free drug, makes them to a promising drug delivery system to improve the bioactivity of diflapolin.

Systemic administration of histone deacetylase inhibitors (HDACi), like valproic acid (VPA), is often associated with rapid drug metabolization and untargeted tissue distribution. This requires high-dose application that can lead to unintended side effects. Hence, drug carrier systems such as nanoparticles (NPs) are developed to circumvent these disadvantages by enhancing serum half-life as well as organ specificity.This chapter gives a summary of the biological characterization of HDACi-coupled NPs in vitro, including investigation of cellular uptake, biocompatibility, as well as intracellular drug release and activity. Suitable methods, opportunities, and challenges will be discussed to provide general guidelines for the analysis of HDACi drug carrier systems with a special focus on recently developed cellulose-based VPA-coupled NPs.

A Raman-based label-free analytical method was developed to detect the antibiotic ciprofloxacin (CIP) in various pharmaceutical formulations in the presence of different matrices (e.g., ear drops, eye drops and infusion solutions). The Raman spectral analysis is performed for semiquantification in the case of a low background Raman signal, i.e., the signal originating from the excipient and carrier substance of the formulation does not interfere with the fingerprint spectrum of ciprofloxacin. In the case of a background spectrum rich in Raman modes originating from the excipient and carrier substance of the formulation, the pharmaceutical formulation is diluted 1:5000, and thus, the background signal is undetectable. Due to the high affinity of ciprofloxacin towards metallic surfaces, surface-enhanced Raman spectroscopy (SERS) is applied to allow for the sensitive detection of ciprofloxacin. Moreover, the developed measurement routine can be applied to monitor the degradation of the active component ciprofloxacin within the pharmaceutical formulation. The developed assay can therefore be extended to the pharmaceutical industry for quality control in assay applications or the preparation of individualized medicines.

Bacterial nanocellulose has been widely investigated for wound healing applications, mainly due to its moisturizing capabilities and biocompatibility. Even though the topical therapy of nail diseases could benefit from these properties, this application has not yet been investigated. Therefore, actively hydrating nail patches based on bacterial nanocellulose were developed to improve the delivery of ciclopirox olamine and Boswellia serrata extract through the nail plate. The nanocellulose matrix was used to enable the application of hydration enhancing solutions based on glycerol and urea as a mechanically stable patch. While the favorable mechanical characteristics of the material remained unchanged, an increase of the incorporated glycerol concentration enhanced the transparency and wetting capacity of the patches. A biphasic drug release from the patches could be observed for drug and extract with a faster release for the hydrophilic ciclopirox olamine. High glycerol concentrations correlated with increased cumulative release and permeation through keratin films for drug and extract, demonstrating the hydration driven permeation enhancement. Patches containing ciclopirox olamine showed strong antimycotic effects against relevant pathogens for onychomycosis. The present finding proposed the combination of bacterial nanocellulose with glycerol, urea and different drug as a promising platform for the local treatment of nail diseases.

Bacterial nanocellulose (BNC) is a highly interesting biomaterial due to some outstanding properties especially when used in medical therapeutics and diagnostics. BNC is absolutely bioinert and is characterised by intrinsic properties such as high tensile stiffness and elasticity, high porosity, exceptional water uptake and swelling capacity. Furthermore, these properties can be adjusted in a very defined way by specifically changing the cultivation conditions or performing post-modifications such as crosslinking, functionalisation with additives, dehydration or drying. Especially the high tensile strength of the nanofibrillar material has been the subject of many investigations in the past couple of years. Nevertheless, the enormous tensile strength and elasticity of BNC is contrary to an almost purely viscous behaviour under compressive load. In the present study, different methods to influence the mechanical behaviour under compression with respect to load bearing applications of BNC are systematically investigated. The possibilities and limitations of the variable layer-by-layer cultivation known as Mobile Matrix Reservoir Technology (MMR-Tech) as well as the effect of different post-modification strategies of BNC are thoroughly investigated. Beside of commonly used indentation tests for characterising the mechanical properties of BNC, we introduce a novel evaluation methodology based on mechanical relaxation measurements and an evolutionary regression algorithm for the derivation of a viscoelastic material law, which for the first time allows standardised, comparative viscoelastic investigations of soft-matter biomaterials to be performed independently of the measurement setup. Using this methodology, we are able to show, that cultivation conditions for BNC and suitable post-modifications can result in different effects on the viscoelastic behaviour of the fabricated composites. We show that the cultivation conditions for BNC primarily affect the height of dispersion and the frequency of the relaxation centre which corresponds roughly to the mean value of the logarithmic distributed relaxation times, and that these effects could be enhanced by post-modifications. However, we also identify parameters, such as the width of the relaxation region, which corresponds roughly to the standard deviation of the logarithmic distributed relaxation times, on which the type of cultivation obviously shows no influence but which can be influenced exclusively by post-modifications. Our methodology enables for the first time a clear identification of those parameters which represent a significant factor of influence to the viscoelastic material behaviour, which should enable a more targeted and application-relevant development of BNC composites in the future.