Search

A novel hybrid Luo-Cuk converter designed for LED lighting systems combines elements from both Luo and Cuk topologies. By integrating the input branch of both topologies, the converter, employing a single switch, can generate two distinct types of outputs simultaneously. One output follows a Luo-type, while the other adopts a Cuk-type . Through a series connection of the outputs from Luo and Cuk topologies, the voltage gain of the converter has been notably enhanced. The converter's output can be effectively regulated using a single controller. To validate the consistency between the topology's performance and theoretical analysis, simulation and prototype results have been provided.

The emergence of converters has triggered a paradigm transfer in the field of power electronics. Recently, DC/DC converters have predominantly employed alternative energy sources and become viable technologies for low- and high-power applications. The DC/DC converter is crucial in power conversion within renewable energy systems, such as hydro, solar photovoltaic (PV), fuel cells (FC), and wind. Its primary role is to modify the voltage and current levels to meet the system's requirements. This article comprehensively examines CUK, ZETA, and single-ended primary-inductor converter (SEPIC) in several phases, including enhancing efficiency, achieving cost-effective operation and mitigating switching losses. Furthermore, this study overviews each converter's operational modes and efficiency-output power comparison. This article compares integrating solar PV and FC technologies into various converters.

High battery voltages increase inverter switching and harmonic losses of the electric machine. These losses dominate at low speeds in the partial load range, where the customer relevant Worldwide Harmonized Light Vehicles Test Procedure (WLTC) driving cycle is located. By installing a bidirectional DC/DC converter between the inverter and the battery, the input voltage of the inverter can be adjusted to various torque/speed conditions, thereby enhancing the efficiency and range of the electric sports car. Outside of the WLTC, the DC/DC converter is not operated and is short-circuited by a bypass. Additionally, the utilization of synchronous modulation methods, as opposed to space vector pulse width modulation (SVPWM), within the WLTC is made possible by the variable DC-Link voltage, further reducing switching and harmonic losses. In this paper, different topologies of DC/DC converters are proposed. The investigations are conducted on an 800 V system. To facilitate this, a script-based toolchain was developed based on analytic and fast calculating waveform models. The impact of the DC-Link voltage on energy efficiency during the WLTC is examined, and sensitivities are presented. A multi-objective optimization is carried out based on the WLTC driving cycle to demonstrate the maximum trade-offs between increasing the electric range and the power density of the DC/DC converter.

Simulation of SIMO based DC-DC Converter for multi level Solar PV Inverter is presented in this paper. In order to reduce the number of distinct DC supplies for an H-bridge inverter SIMO DCDC converter is applied which in turn allows the usage of single PV system for a multi level H-bridge inverter. Simulation model of three level and five level inverters is built and results are presented to validate the proposed ideas.

In this paper, current control of 6/4 switched reluctance motor (SRM) fed by both power factor correction (PFC) SEPIC and CUK converter is realised and asymmetric bridge converter is used to drive SRM. Furthermore, SEPIC and CUK DC-DC converters are connected in series to diode bridge rectifier in order to build PFC converters. Average current control of PFC converters is carried out by PI algorithm and both converters are operated at continuous conduction mode (CCM). Besides, switching frequency of PFC and asymmetric bridge converters is 62, 9 kHz with 5750 W power. Studies are conducted by using MATLAB/Simulink software. Total harmonic distortions (THD)s of grid current, grid power factor (PF) and output voltages of the converters are compared. Also, THDs of grid current of each converter are compared by IEEE 519-2014 standard. In addition, current waveform and flux of SRM phases are shown. It is validated by simulations that PFC CUK converter gives better result with 9.08% THD, 0.998 PF than PFC SEPIC converter having 9.61% THD and 0.997 PF. Furthermore, both converters provide the limit defined by standards.

The power produced in a photovoltaic (PV) system is highly dependent on meteorological conditions and the features of the connected load. Therefore, maximum power point tracking (MPPT) methods are crucial to optimize the power delivered. An MPPT method needs a DC-DC converter for its implementation. The proper selection of both the MPPT technique and the power converter for a given scenario is one of the main challenges since they directly influence the overall efficiency of the PV system. This paper presents an exhaustive study of the performance of four step-down/step-up DC-DC converter topologies: Buck-Boost, SEPIC, Zeta and Cuk, using three of the most commonly implemented MPPT techniques: incremental conductance (IncCond), perturb and observe (P&O) and fuzzy logic controller (FLC). Unlike other works available in the literature, this study compares and discusses the performance of each MPPT/converter combination in terms of settling time and tracking efficiency of MPPT algorithms, and the conversion efficiency of power converters. Furthermore, this work jointly considers the effects of incident radiation variations, the temperature of the PV panel and the connected load. The main contribution of this work, other than selecting the best combination of converter and MPPT strategy applied to typical PV systems with DC-DC power converters, is to formulate a methodology of analysis to support the design of efficient PV systems. The results obtained from simulations performed in Simulink/MATLAB show that the FLC/Cuk set consistently achieved the highest levels of efficiency, and the FLC/Zeta combination presents the best transient behavior. The findings can be used as a valuable reference for the decision to implement a particular MPPT/converter configuration among those included in this study. [ABSTRACT FROM AUTHOR]

The power produced in a photovoltaic (PV) system is highly dependent on meteorological conditions and the features of the connected load. Therefore, maximum power point tracking (MPPT) methods are crucial to optimize the power delivered. An MPPT method needs a DC-DC converter for its implementation. The proper selection of both the MPPT technique and the power converter for a given scenario is one of the main challenges since they directly influence the overall efficiency of the PV system. This paper presents an exhaustive study of the performance of four step-down/step-up DC-DC converter topologies: Buck-Boost, SEPIC, Zeta and Cuk, using three of the most commonly implemented MPPT techniques: incremental conductance (IncCond), perturb and observe (P&O) and fuzzy logic controller (FLC). Unlike other works available in the literature, this study compares and discusses the performance of each MPPT/converter combination in terms of settling time and tracking efficiency of MPPT algorithms, and the conversion efficiency of power converters. Furthermore, this work jointly considers the effects of incident radiation variations, the temperature of the PV panel and the connected load. The main contribution of this work, other than selecting the best combination of converter and MPPT strategy applied to typical PV systems with DC-DC power converters, is to formulate a methodology of analysis to support the design of efficient PV systems. The results obtained from simulations performed in Simulink/MATLAB show that the FLC/Cuk set consistently achieved the highest levels of efficiency, and the FLC/Zeta combination presents the best transient behavior. The findings can be used as a valuable reference for the decision to implement a particular MPPT/converter configuration among those included in this study.