Search

In order to reduce the ohmic losses in the slow wave structure (SWS), an elliptical pillar defected photonic crystal waveguide (EPDPCW) is proposed as a SWS for the terahertz traveling wave tube (TWT). Compared with rectangular pillar defected photonic crystal waveguides (RPDPCW), the EPDPCW shows better high-frequency characteristics and lower ohmic losses. According to the particle-in-cell (PIC) results, in the frequency range of 188 GHz to 218 GHz, the saturated output power of EPDPCW is greater than 13.4 W, and the maximum saturated output power is 26.8 W at 196 GHz at a voltage of 9.78 kV and a beam current of 150 mA. Compared to the RPDPCW-TWT, the performance of the EPDPCW-TWT has been significantly improved. [ABSTRACT FROM AUTHOR]

For the purpose of improving performance and reducing the fabrication difficulty of terahertz traveling wave tubes (TWTs), this paper proposes a novel single-section high-gain slow wave structure (SWS), which is named the symmetrical quasi-synchronous step-transition (SQSST) folded waveguide (FW). The SQSST-FW SWS has an artificially designed quasi-synchronous region (QSR) to suppress self-oscillations for sustaining a high gain in an untruncated circuit. Simultaneously, a symmetrical design can improve the efficiency performance to some extent. A prototype of the SQSST-FW SWS for 650 GHz TWTs is designed based on small-signal analysis and numerical simulation. The simulation results indicate that the maximum saturation gain of the designed 650 GHz SQSST-FW TWT is 39.1 dB in a 34.3 mm slow wave circuit, occurring at the 645 GHz point when a 25.4 kV 15 mA electron beam and a 0.43 mW sinusoidal input signal are applied. In addition, a maximum output power exceeding 4 W is observed at the 648 GHz point using the same beam with an increased input power of around 2.8 mW. [ABSTRACT FROM AUTHOR]

A new slow wave structure (SWS), named E-plane loaded sine waveguide (EPLSW) SWS is proposed for the development of G-band traveling wave tubes (TWTs). The structure, derived from the sine waveguide (SW) SWS, features staggered rectangular gratings on the two E-planes, intersecting with the sine-shaped gratings. The natural electron beam tunnel lies between these gratings. The EPLSW-SWS offers improved characteristics compared to the conventional SW-SWS. High-frequency simulation studies reveal that the passband of the EPLSW-SWS extends by more than 33 GHz over the SW-SWS under identical dispersion conditions. Additionally, the interaction impedance of EPLSW-SWS surpasses that of the SW-SWS in the frequency range of 195–255 GHz. Further analysis through particle-in-cell (PIC) results presents that when operating at 19.5 kV and 145 mA for the sheet beam current, it attains a maximum saturated power of 132.7W and a 3 dB bandwidth exceeding 50 GHz. [ABSTRACT FROM AUTHOR]

Terahertz (THz) backward wave oscillators (BWOs) hold immense potential for a broad range of industrial and military applications. This study presents a comparative analysis of 0.34 THz sheet beam (SB) and circular beam (CB) folded waveguide (FWG) BWOs. We examined the design, simulation (CST MWS and PS, HFSS), and performance, revealing that sheet beam BWO outperforms circular beam BWO in terms of interaction impedance, power, efficiency, and bandwidth. Under 20 kV beam voltage and 10 mA beam current conditions, sheet beam BWO achieves 0.47 Ω (0.34 THz) interaction impedance, 0.65 W output power, and a bandwidth of approximately 12 GHz, surpassing the 0.18 Ω , 0.23 W, and 8.5 GHz values of circular beam BWO, respectively. Furthermore, this study encompasses the fabrication and thorough characterization of the sheet beam BWO's slow-wave structure. Experimental validation confirms its effectiveness, with measured S 11 demonstrating reflection below - 10 dB and S 21 exhibiting transmission above - 2 dB. [ABSTRACT FROM AUTHOR]

Terahertz backward wave oscillators based on double corrugated waveguides are enabling devices for modern satellite communication systems. This research focuses on the design of a 0.34 THz double corrugated waveguide-based interaction structure using a sheet beam. This choice allows the use of shorter pillars along with a narrow gap between pillar rows. Shorter pillars are easier to manufacture and a narrow gap is required for better interaction impedance. Circular beams restrict the use of larger pillars and narrow gap between pillars. The performance of this interaction structure is compared with a folded waveguide. Under the same operating conditions involving a 20 kV beam voltage and a 30 mA beam current, the double corrugated waveguide interaction structure exhibits impressive performance in simulations, featuring an interaction impedance of 0.52 Ω at 0.34 THz, an output power of 3.2 W, and a bandwidth extending to approximately 20 GHz. In contrast, the folded waveguide, as per simulation results, registers values of 0.43 Ω , 2.6 W, and a 12 GHz bandwidth, respectively. The proposed double corrugated waveguide-based interaction structure is fabricated using modern CNC machining. Experimental validation reinforces the effectiveness of this design, with measurements indicating reflection below −20 dB and transmission exceeding −2 dB. [ABSTRACT FROM AUTHOR]

In order to improve the performance of sine waveguide (SW) traveling wave tube (TWT), an elliptical beam-tunnel sine waveguide (EBTSW) slow wave structure (SWS) is proposed. EBTSW-SWS not only has high interaction impedance in a relatively wide frequency band but also has an elliptical beam-tunnel. The simulation results of high-frequency characteristics show that, under the same dispersion, the passband of EBTSW-SWS increases by 30% compared to the SW-SWS, and the average interaction impedance of EBTSW-SWS is higher than that of SW-SWS in almost the whole passband. Moreover, the particle-in-cell (PIC) simulation results reveal that under the operating voltage of 20.8 kV and beam current of 150 mA, EBTSW-TWT can provide more than 70 W of saturated output power in the frequency range of 200-260 GHz, reaching the maximum power of 151 W at 220 GHz with the maximum electronic efficiency of 4.85%. [ABSTRACT FROM AUTHOR]

A $Q$ -band traveling-wave tube (TWT) with profiled helix pitches and profiled inner diameters of slow wave structure (SWS) is proposed. The transmission characteristics of the $Q$ -band TWT are simulated by the Computer Simulation Technology (CST). In the operating frequency band (36.5–41.5 GHz), the simulated voltage standing wave ratio (VSWR) is less than 1.5. In addition, the beam–wave interaction is simulated to predict the performance of the $Q$ -band TWT when the beam voltage and beam current are 8.5 kV and 60 mA, respectively, and the axial focusing magnetic field is 0.4 T. In the operating frequency band, the self-oscillation is well suppressed, and the device efficiency of the $Q$ -band TWT exceeds 63.5%, and the saturated output power and gain exceed 83 W and 45 dB, respectively, especially the device efficiency can reach the maximum of 69.5% at 37 GHz. When it is backed off 6 dB from the saturation, the device efficiency exceeds 40.5%, up to 42.7% at 39 GHz. Preliminary experiments have confirmed the design. These results show that the proposed $Q$ -band TWT has important applications to the next generation wireless communication system with high efficiency. [ABSTRACT FROM AUTHOR]

The angular log-periodic meander-line traveling wave tube (TWT) is a kind of low voltage, small-sized, high power, low cost, on chip amplifiers, and considered as a key part of the advanced communication systems, the future biomedical applications and the next electronic counter measure (ECM) instruments et al. Here, an angular log-periodic meander-line TWT is presented in this article. The angular log-periodic meander-line slow wave structure (SWS) is supported by two diamond rods. The dispersion and the impedance characteristics are analyzed in detail. In order to reduce the reflection loss, a gradual ridged waveguide is connecting the input–output standard rectangular waveguide to the meander-line SWS. The particle in cell (PIC) simulations show that the output power of the TWT can reach 55 W at 34 GHz with the operation voltage of 1800 V and the beam current of 0.2 A. The SWS is manufactured by a laser machine with Molybdenum sheet. The assembled TWT is tested and the results show that the ${S}_{{11}}$ is less than −10 dB at 30–39 GHz. The ${S}_{{21}}$ mismatch between the simulated and the measurement is discussed at the end. [ABSTRACT FROM AUTHOR]

A novel electron-optical system (EOS) for ${G}$ -band traveling-wave tubes (TWT) is investigated by simulation and verified by experiment. The EOS includes a sheet beam electron gun, a tunable periodic cusped magnetic focusing (TPCMF), and a collector. An elliptical focus electrode (FE) featuring a simple geometry and easy fabrication is utilized to compress the pencil beam into the sheet beam with a cross section of 0.4 mm $\times0.1$ mm. The electron gun with a cylindrical cathode of 0.8 mm diameter generates the sheet beam with voltage of 22 kV and current of 115 mA. Based on the sheet beam electron gun, the TPCMF with easy assembly and compact size is then proposed. The experimental results show that the beam transmission is 92.1% within a beam tunnel (its length 21.2 mm and cross section 0.8 mm $\times0.15$ mm). The EOS is suitable for ${G}$ -band TWT. [ABSTRACT FROM AUTHOR]

A phase shift that is caused by the machining errors of independent circuits would greatly affect the efficiency of the power combination in traditional multi-beam structures. In this paper, to reduce the influence of the phase shift and improve the output power, a multi-beam shunted coupling sine waveguide slow wave structure (MBSC-SWG-SWS) has been proposed, and a multi-beam overmoded flat-roofed SWG traveling wave tube (TWT) based on the MBSC-SWG-SWS was designed and analyzed. A TE10-TE30 mode convertor was designed as the input/output coupler in this TWT. The results of the 3D particle-in-cell (PIC) simulation with CST software show that more than a 50 W output power can be produced at 342 GHz, and the 3 dB bandwidth is about 13 GHz. Furthermore, the comparison between the single-beam sine waveguide (SWG) TWT and the multi-beam overmoded SWG TWT indicates that the saturated output power of the multi-beam overmoded SWG TWT is three times more than that of the single beam SWG TWT. [ABSTRACT FROM AUTHOR]

An attenuator supporting meander-line (ASML) slow wave structure (SWS) is proposed for a Ka-band traveling wave tube (TWT) and studied by simulations and experiments. The ASML SWS simplifies the fabrication and assembly process of traditional planar metal meander-lines (MLs) structures, by employing an attenuator to support the ML on the bottom of the enclosure rather than welding them together on the sides. To reduce the surface roughness of the molybdenum ML caused by laser cutting, the ML is coated by a thin copper film by magnetron sputtering. The measured S11 of the ML is below −20 dB and S21 varies around −8 dB to −12 dB without the attenuator, while below −40 dB with the attenuator. Particle-in-cell (PIC) simulation results show that with a 4.4-kV, 200-mA sheet electron beam, a maximum output power of 126 W is obtained at 38 GHz, corresponding to a gain of 24.1 dB and an electronic efficiency of 14.3%, respectively. [ABSTRACT FROM AUTHOR]