Search

In this paper, the possibility of utilising coarse recycled concrete aggregate (CRCA) obtained from a construction and demolition waste (CDW) plant in Delhi to make 60 MPa self-compacted concrete (SCC) was evaluated. The CRCA was used in as-collected condition and was not processed any further. The aggregate packing (bulk) density (APD) method was adopted to prepare the SCC-CRCA mixture in order to obtain an aggregate mixture exhibiting maximum bulk density/least void content (45%). In addition, SCC was made using aggregate mixtures in which the natural coarse aggregate (NCA) was replaced with CRCA at 0%, 20% and 100% of the total coarse aggregate content by weight. The cement, fly ash, silica fume and water were kept constant for all SCC mixtures. The effects of CRCA on the flow behaviour, mechanical strength, shrinkage characteristics and microstructure properties of SCC mixtures were evaluated. The test results indicated that SCC mixtures made with up to 45% CRCA replacement can be used for structural concrete, which is higher than that recommended in Indian (20%) and international specifications (35%) for traditionally vibrated (conventional) concrete. [ABSTRACT FROM AUTHOR]

Beam-column joints are crucial load transmission zones because they face concentrated forces from both the beams and the columns. High shear and axial stresses caused by these concentrated forces in the area of the joint may result in decreased joint strength. This article proposes a new beam-to-column connection developed for precast concrete-resisting frames. Concrete mixtures are enhanced mechanically by adding nano silica as it increases compressive strength, flexural strength, and abrasion resistance. Within the concrete, it creates a solid, gel-like matrix that fills voids and strengthens the whole construction. In this study, three reinforced concrete beam-column joint specimens were cast with fly ash, the other three with nano-silica and fly ash, and one sample with nano-silica and a control mix without admixtures was cast. Specimen cast using fly ash and nano-silica is subjected to cyclic loading after 28 days of curing. A load capacity of 100 kN was imposed on the column during testing. It was observed that a gradual increase in fly ash decreased the compressive and flexural strength of the beam-column joints. This decrease in strength was addressed by adding 2.5% nano-silica. Nano silica acts as a nucleus to bond tightly with cement particles during hydration. The results showed that the flexural strength equivalent to that of a controlled specimen can be achieved by adding nano-silica at 2.5% and fly ash at 60%. The highest loading of 38.1 kN can be applied to the specimen with nano-silica without fly ash. Although a higher axial compression ratio can improve the bearing capacity and initial stiffness, it can also reduce deformation capacity and flexibility. [ABSTRACT FROM AUTHOR]

This paper introduced a new concrete composites made by quaternary binder by partially replacing ordinary Portland cement (OPC) with different percentages of supplementary cementitious materials (SCMs). The motivation is to reduce our dependency on OPC to reduce CO2 emission and carbon foot print. As the main substitute for the OPC, siliceous fly ash was used (FA). Moreover, silica fume (SF) and nanosilica (nS) were also used. This study utilized the following contents of SCMs used: 5% of nS; 10% of SF; 0, 15, and 25% of FA. During examinations the main mechanical properties of concrete composites, i.e. compressive strength (fcm) and splitting tensile strength (fctm) were assed. The brittleness of these materials was also analysed. Based on the conducted studies, it was found that concrete composite based on quaternary blended cements, of series Mix3, has shown the best results in terms of good strength parameters, whereas the worst mechanical parameters were characterized by concrete of series Mix4. On the other hand, concrete including only SF and nS (Mix2 series) were characterized by the greatest brittleness. It was observed that fcm of concrete composites for series Mix2, Mix3, and Mix4 increase of 41%, 48%, and 31% respectively compared with the concrete without additives, i.e. series Mix1. In addition, fctm also increase of 39%, 47%, and 30%, respectively, for the three series mentioned above, compared with the control concrete. Concrete of series Mix3, with high mechanical properties and demonstrating the features of quasi-plastic material, i.e. having lower brittleness, can be used in concrete and reinforced concrete structures subjected mainly to dynamic and cyclic loads. Therefore, it can be used, in the construction of foundation structures for machines and other types of structures in which the above-mentioned loads are dominant. [ABSTRACT FROM AUTHOR]