Search

Aim of present study was to develop biological catalysts of L-arabinose isomerase (L-AI) by immobilizing on four different supports such as multiwalled carbon nanotube (MWCNT), graphene oxide (GOx), Santa Barbara Amorphous (SBA-15) and mobile composite matter (MCM-41). Also, comparative analysis of the developed catalysts was performed to evolve the best in terms of transformation efficiency for D-tagatose production. The developed nano-enzyme conjugates (NECs) were characterized using the high resolution transmission electron microscopy (HR-TEM) and elemental analysis was performed by energy dispersive X-ray spectroscopy (EDS). The functional groups were investigated by Fourier transform infra red spectroscopy. Also, the thermo gravimetric analysis (TGA) was employed to plot a thermal degradation weight loss profile of NECs. The conjugated L-AI with MWCNT and GOx were found to be more promising immobilized catalysts due to their ability to provide more surface area. Conversion of D-Galactose to D-Tagatose at moderate temperature and pH was observed to attain the equilibrium level of transformation (~50%). On the contrary, NECs prepared using SBA-15 and MCM-41 as support matrix were unable to reach the equilibrium level of conversion. Additionally, the developed NECs were suitable for reuse in multiple batch cycles. Thus, promising nanotechnology coupled with biocatalysis made the transformation of D-Galactose into D-tagatose more economically sustainable. [Display omitted] [ABSTRACT FROM AUTHOR]

Here we present a simple method to fill multiwalled carbon nanotubes (MWCNT) with silver. This method involves stirring of MWCTs in AgNO 3 solution at room temperature in open air followed by heating in H 2 atmosphere at 250 °C for two hours. Process also leads to small coating of Ag on the surface. We confirmed the presence of crystalline silver in both coating and filling in hybrid MWCNTs by high resolution transmission electron microscopy, energy dispersive X-ray spectroscopy and electron diffraction. After silver coating and filling, bulk thermal diffusivity and thermal conductivity of Ag hybrid MWCNTs were increased by 242% and 255%, respectively. Furthermore, current-voltage measurements using tuna probe in atomic force microscopy showed higher number of charge carriers in the Ag hybrid nanotubes compared to pristine MWCNTs which resulted in up to 173% increase in their electrical conductivity. The Ag hybrid MWCNT based sensor also showed rapid and reversible sensing for I 2 vapors: bulk sensor film demonstrated sensing response of 45% in just ~60 s at room temperature. However, the sensor recovery was slower: after removal of I 2 vapors source, the recovery took 400 s and required heating at 100 °C in air. Response and recovery of sensor film was maintained after repeated cycles of exposure. Finally, the Ag hybrid MWCNTs film displayed high stability and selectivity for I 2 vapors. [Display omitted] • Synthesis of Ag filled MWCNTs using a simple method • Bulk thermal conductivity of Ag hybrid MWCTs is 255% more than of MWCNTs. • Addition of Ag increases the bulk electrical conductivity of MWCNTs by 173%. • More negative charge carriers in the Ag hybrid MWCNTs than pristine MWCNTs • Ag hybrid MWCNTs showed rapid and reversible sensing for I 2 vapors. [ABSTRACT FROM AUTHOR]

[Display omitted] • The role of CNT in promoting crystallinity of composites. • Morphological and structural changes upon thermal treatment. • BiOI together with other phases enhanced photocatalytic activity. • BiOI/CNT composites showed higher photocatalytic activity for phenol and RhB. • Photocatalytic activity is dependent on synthesis, crystallinity and BiOI phases. In this work, we have prepared BiOI/CNT composites by hydrothermal method and studied the impact of CNT and hydrothermal treatment conditions (temperature and time) simultaneously on phenomena such as crystallization. The samples were studied using X-ray Diffraction (XRD), nitrogen sorption (Brunauer–Emmett–Teller (BET) specific surface areas), Scanning Electron Microscopy assisted with Energy Dispersive X-Ray spectroscopy (SEM-EDX), High Resolution Transmission Electron Microscopy (HRTEM), UV–vis Diffuse Reflectance spectroscopy (DRS), Raman spectroscopy and photoluminescence spectroscopy (PL). The different heat treatments applied and varied amount of CNT was found to have a profound effect on the structural, morphological, compositional and optical properties of the prepared composites. The distinguishable changes in the above-mentioned properties were clearly visible for the samples prepared at higher temperature and longer duration (150 °C, 6.30 h). Surprisingly, the presence of other phases of BiOI, such as Bi 7 O 9 I 3 , Bi 4 O 5 I 2 , Bi 5 O 7 I, also co-existed at the same time, although in low amount. Finally, for the study, the photocatalytic efficiency of the prepared samples was tested for phenol and RhB, as model pollutants, under visible light irradiation for 240 min and 120 min, respectively. The results revealed that the composites prepared at higher temperature with longer duration showed superior performance for the photodegradation of phenol and RhB. Additionally, the composites performed better than their respective reference samples in each case. Interestingly, the introduction of CNT promoted the crystallinity in the composites and promising results for the removal of phenol and RhB were achieved by the use of low power ordinary visible lamps. [ABSTRACT FROM AUTHOR]