Search

To improve the low-load stable combustion capacity of a low-grade coal-fired boiler, this study proposed to reform C-layer secondary air, which was then used to improve the ignition and combustion stability of coal/airflow of a 600 MWe Foster Wheeler down-fired boiler. Cold airflow experiments and industrial measurements were carried out to investigate the influence of the new C-layer secondary air on the aerodynamic and combustion characteristics at low load under different C-layer secondary air ratios and damper openings, respectively. The flow and mixing characteristics of the C-layer secondary air and coal/airflow, the flue gas temperature and NOx, O2, and CO concentration distributions in the furnace at low load were examined. With increase in the C-layer secondary air ratio, the flow range of coal/airflow gradually expanded. The mixing distance first increased and then decreased. At an air ratio of 25%, the mixing distance was the longest. Industrial measurements showed that compared with that at the C-layer secondary air damper opening of 0%, the coal/airflow ignited earlier at 40% (corresponding to the C-layer secondary air ratio of 23.73%), and the flue gas temperature in the furnace increased substantially. At C-layer secondary air damper opening of 0%, 20%, and 40%, carbon content in the fly ash was 4.62%, 5.32%, and 4.20%, respectively. The respective NOx emissions at the furnace exits were 450 mg/Nm3, 378 mg/Nm3, and 427 mg/Nm3, (O2 = 6%). In actual operation, 40% is recommended as the optimal C-layer secondary air damper opening. [ABSTRACT FROM AUTHOR]

On a cold single-phase test stand, the effect of central air on the exit flow field of Babcock, Germany, burner was investigated. Industrial measurements were taken for a 700 MW wall-fired pulverized-coal utility boiler with above burners. Gas temperature, gas composition and concentration in the burner area were measured at 444 MW, 522 MW and 645 MW loads, respectively. Only when the central air mass flow was zero did a center reflux zone exist in the burner outlet area. The steady combustion of faulty coal was aided by early mixing of primary and secondary air, which was made possible by the decreased central air mass flow. At all different loads, the pulverized coal in center region took a long distance to ignite. The temperature in center steadily dropped as central air mass flow decreased, while the temperature in secondary air region gradually rose. Within 1.5 m from the primary air duct outlet, the highest CO concentration was 25 ppm and the highest O2 concentration was close to 21% under all loads. The gas concentration near sidewall was more influenced by load. With all valves opening of burner center air at 30%, the boiler was able to operate safely and stably without oil at a load of 262 MW. The furnace chamber temperature in burner area reached 1056.1 °C. [ABSTRACT FROM AUTHOR]

To address the problem of late ignition and poor burnout of Foster-Wheeler down-fired boilers, this study proposed a new combustion technology, which combines adding on arch secondary air and alternately arranging the fuel-lean coal/airflow (FLCA) and fuel-rich coal/airflow (FRCA). The coal particle trajectories of FLCA and FRCA and overall aerodynamic characteristics in the furnace were studied at FRCA and FLCA ratio (RRL) of 5:5, 7:3, and 9:1. The results showed that even at a low FRCA ratio, the new combustion technology could still effectively ensure the penetration depth of pulverised coal/airflow. At different RRL values, the main airflow from the arch appeared in the near-wall area and could penetrate downwards into the cold ash hopper area. With an increase in the value of RRL, the deflection degree of FLCA towards the furnace wall increased, while that of FRCA decreased. At RRL of 7:3, both the penetration depth and deflection degree of FRCA and FLCA were at a high level, which was conductive to promoting the burnout and recommended in practical applications. [ABSTRACT FROM AUTHOR]

The outlet velocity field of the pulverized coal burner is one of the important factors affecting its operating characteristics. In this article, cold tests were carried out for a new swirl burner with a pre-combustion chamber, and the influence of the air ratio on the outlet velocity field of the burner was studied. Through the cold single-phase test on the 1:3 model test bench, the burner outlet cold air velocities were obtained. The results shown that the formation of the central recirculation zone was mainly affected by the secondary air, a stable central recirculation zone could not be formed when the velocity of secondary air was too low. When the total air of the burner was fixed, the secondary air increased, the length of the central recirculation zone increased, and the mixing speed between different flows increased. When the ratio of the mass flow of the secondary air to tertiary air increased from 26:74 to 85:15, the reflux rate increases 5.5 times, which helped to keep the combustion stable. [ABSTRACT FROM AUTHOR]

To effectively control the flow and combustion of pulverised coal in down-fired boilers and improve their thermal efficiency while ensuring low NOx emissions, on arch secondary air (OASA) combustion technology and a smoke-tracing analysis were proposed. The aerodynamic characteristics of a 300-MWe Foster Wheeler (FW) down-fired boiler with the OASA ratios (ROASA) of 0%, 10%, 20%, and 30%, the flow trajectories and mixing characteristics of OASA, and fuel-rich coal/air flow (FRA) and fuel-lean coal/air flow (FLA) were studied experimentally. For the ROASA of <10%, FRA and FLA flow to furnace centre soon after they are injected into the furnace. OASA and FLA may mix with FRA before ignition. For the ROASA of 20% or higher, FRA and FLA flow to the near-wall area soon after being injected into the furnace. FRA mixes with OASA after ignition. With the increase in ROASA, the mixing distance between OASA and FRA increases first and then decreases. The penetration depth of coal/air flow and furnace airflow fullness increases. For the ROASA of 30%, the dimensionless penetration depth of coal/air flow can exceed 0.7. Furnace dimensionless airflow fullness at all the dimensionless heights can exceed 0.6. In real operation, the recommended ROASA is between 20 and 30%. [ABSTRACT FROM AUTHOR]

To further reduce the NOx emissions of the down‐fired boiler while improving its low‐load stable combustion capacity, a new low NOx combustion organization mode that utilizes the high velocity parallel oil‐secondary air to improve the pulverized coal combustion process was proposed based on a novel stable combustion technology. We carried out cold airflow experiments under different oil‐secondary air and F‐layer secondary air distributions (mass flow rate ratios of 1:9, 1:3, 2:3) based on a 300 MWe Foster Wheeler down‐fired boiler to study its influence on the flow and mixing characteristics of the coal/airflow. Results show that the mixing between the oil‐secondary air and the fuel‐rich coal/airflow is gradually delayed with the increase of the secondary air distribution. When the secondary air distribution reaches more than 2:3, the oil‐secondary air starts to become the dominant airflow that influences the whole flow field in the furnace. Based on the result of the cold airflow experiment, we carried out industrial measurements under different parallel oil‐secondary air and F‐layer secondary air distributions (4:6, 5:5, 6:4) on a 600 MWe FW down‐fired boiler under the condition of using the high velocity oil‐secondary air. The ignition distance of the fuel‐rich coal/airflow, the flue gas temperature, the O2, CO, and NOx concentrations in the furnace were measured. At the secondary air distribution of 4:6, the ignition distance of the fuel‐rich coal/airflow was about 1.31 m. When the secondary air distribution was increased to 5:5 and 6:4, the ignition was put off, but the pulverized coal/airflow could still catch on fire in time. With the increase of the parallel oil‐secondary air proportion, the flame center in the furnace did not move downward substantially. In three cases, the lowest O2 concentrations in the inspection port area under the burner were all below 1% (peak CO concentration values were all above 28,000 ppm). The pulverized coal all burned in a strong reducing atmosphere. At secondary air distributions of 4:6, 5:5, and 6:4, NOx emissions of the boiler were, respectively, 825.83, 819.48, and 853.86 mg/Nm3 (O2 = 6%). The thermal efficiency was, respectively, 90.09%, 89.16%, and 90.98%. In actual operation, the recommended secondary air distribution is 6:4. [ABSTRACT FROM AUTHOR]

• An understanding of the radial air staging method for PC utilization is improved and the key parameter (OFA distribution) is optimized. • Compared to the traditional axial air staging method, for the radial air staging method, the OFA distribution has a greater effect on the heat release from PC particles. • The increased R IO is not conducive to the rapid devolatilization from PC particles, resulting in poorer combustion stability of the boiler. • The increased R IO promotes the oxidation reaction of N released from PC particles, which is detrimental to boiler NO x emission reduction. • The advanced mixture of the OFA with the main airflow facilitates the burnout of the PC particles as the R IO increases. Radial air staging is an innovative method for reducing NO x emissions from coal-fired boilers compared to conventional axial air staging. However, an important issue in using this method is to set the over-fired air (OFA) distribution rationally to achieve good boiler performance. This paper aims to optimize the OFA distribution by evaluating important gas-particle (GP) parameters that influence the pulverized coal (PC) combustion performance. The GP flow experiment is conducted in a laboratory furnace model of a coal-fired boiler with different OFA distributions. The experimental results show that as R IO (Two-level OFA distribution ratio) changes from 0:1 to 1:0, the mixture of the OFA jet and airflow in the main combustion zone is advanced, which is conducive to PC burnout. Meanwhile, the size of the central recirculation zone decreases, resulting in poor PC ignition. It is worth noting that at R IO of 1:0, the central recirculation zone disappears at section y/d = 2.5, indicating that there is no high-temperature flue gas downstream to heat the fresh PC particles, which is extremely unfavorable for the stable combustion of the PC. In addition, at R IO of 0:1, compared to other cases, there are more particles in the central recirculation zone, which promotes the reduction reaction of N element released from PC particles, thus reducing NO x emission. According to the comprehensive evaluation, it is recommended that the R IO of the two-level OFA be set to 1:1 when using radial air staging in a coal-fired boiler. The results provide new insights into the application of the air staging method for efficient and clean PC utilization. [ABSTRACT FROM AUTHOR]

• Flow and combustion characteristics of down-fired boiler with central secondary air supply are studied. • Central secondary air ratio that is beneficial to the flow field symmetry and penetration depth is given. • Reasons for the burnout of burner nozzle and the blending proportion limitation of bituminous coal are obtained. • Technical improvement ideas for increasing the blending proportion of bituminous coal are proposed. The existing central secondary air swirl pulverized coal burner and separated secondary air interval arrangement down-fired boiler combustion technology used for the combustion of blended bituminous coal encounter several problems such as burner nozzle burnout, limited proportion of bituminous coal blending under high load, etc. In this study, the effects of central secondary air on the flow, pulverized coal ignition, burnout, and NO x emissions characteristics of a 600-MWe down-fired boiler with the central secondary air combustion technology were studied by the combination of cold-modeling experiments and industrial-scale experiments. Moreover, the reasons for the burnout of the burner nozzle and limited blending proportion of bituminous coal were analyzed and revealed. Cold-modeling experiments showed that with the increase of the central secondary air ratio, the peak value of the dimensionless vertical velocity increases; however, the flow field asymmetry occurs in the furnace when the air ratio increases to 6%. Considering the symmetry of the flow field and the characteristics of the downdraft, the central secondary air ratio is advised to be less than 3.52%. The industrial-scale experiments of burning bituminous coal under 360-MWe load show that the ignition distance of coal/air flow is about 0.10 m for all the cases at 30, 50, and 75% of the central secondary air damper opening, respectively, which reveal that the serious burner nozzle burnout is caused by the premature ignition of the coal/air flow. Under three types of central secondary air damper openings, the NO x emissions at furnace outlet are 333, 329, and 355 mg m−3 @ 6% O 2 , respectively. By considering the flow, combustion, and temperature field characteristics in the furnace, reduction in the central secondary air supply air volume can delay the ignition of the coal/air flow, which provides a new idea and method to achieve a high proportion of bituminous coal blending at rated load. [ABSTRACT FROM AUTHOR]

To ensure good combustion stability, industrial pulverized coal-fired boilers normally employ a swirl burner with pre-combustion chamber (PCC). Owing to the high cross-sectional heat load of the PCC, there is potential for slagging, which can affect the safe and stable operation of the boiler, but can be avoided or reduced through the selection of suitable operating parameter values. Here, the effects on the slagging characteristics of PCC of varying the ratio of the inner to the outer secondary air mass flow rates in a swirl burner, R SA , from 0.00 to 0.83 were investigated using a computational fluid dynamics (CFD) simulation approach. The rates of collision, deposition, and sticking were analyzed. The results showed that as the R SA increases, the total collision rate of the pulverized coal particles in the PCC increases, and when R SA = 0.83, the total collision rate in the PCC is about 7 times of that when R SA = 0.00. Further, slagging tends to appear on the wall near the outlet of the PCC, and the degree of slagging in the PCC first decreases and then increases with increasing R SA. The optimum R SA range was found to be 0.22–0.38, which is conducive to the safe and stable operation of industrial pulverized coal-fired boilers. [Display omitted] • The slagging characteristics in the pre-combustion chamber were studied. • The rates of collision, deposition, and sticking were analyzed. • Slagging tends to appear near the exit area of the pre-combustion chamber. • The degree of slagging first decreases and then increases as R SA increases. [ABSTRACT FROM AUTHOR]

In this study, a novel swirl burner for industrial pulverized coal boiler was studied by laboratory experiments and industrial application tests. First, a cold flow experiment was carried out on a 1:3 scale model experimental platform. The cold air velocities of burner outlet were measured in detail. Moreover, the influence of the mass flow ratio of the inner and outer secondary air on the shape of the central reflux zone and the reflux rate at the burner outlet was analyzed. It was found that a stable central reflux zone can be formed at the burner outlet. In addition, an industry application test was carried out in a 29 MW hot water boiler. The flue gas temperature at the burner outlet and the composition of exhaust gas were obtained under different operating parameters. The influence of inner and outer secondary air damper opening on burner performance (ignition performance, NO x emission characteristics, stable combustion performance, and anti-slagging performance) was analyzed. The influence of inner secondary air damper opening on burner performance was found to be greater than that of outer secondary air damper opening. The maximum concentration of NO x emission at furnace outlet was 364.9 mg/m3, and low-NO x combustion was achieved for industrial pulverized coal boilers. The minimum load without natural gas support was 3 MW. The load regulation rate was close to 10:1, and low load combustion stability was achieved. During three heating seasons, the normal operation of the boiler was not affected by slagging. • Laboratory experiments and industrial application tests are performed. • Influence of different inner and outer secondary air mass-flow ratio are investigated. • Low NO x combustion is achieved for industrial pulverized coal boilers. • Low load combustion stability is achieved for industrial pulverized coal boilers. [ABSTRACT FROM AUTHOR]

A burner structure suitable for atmospheric entrained-flow gasifiers using fine ash as feedstock was proposed. The study investigates the impact of the burner structure on the mixing characteristics through 0.75:1 (geometry reduction) single-phase airflow experiments. Additionally, numerical simulations were conducted to study of the gasification process of fine ash in a 10,000 Nm3/h atmospheric entrained flow gasifier. The results indicate that a larger residual temperature near the burner outlet was observed when the diameter of the burner's gasification agents channel was 10 mm or 15 mm, approximately 0.7–0.8. Additionally, the mixing degree of the two airflows at the burner outlet was high, and the distance required for complete mixing was short. When the diameter of the gasification agent channel was 15 mm, the mixed syngas flow velocity was appropriate. This resulted in a maximum temperature of 2500 °C, an 80 % carbon conversion rate, and an outlet effective syngas (CO + H 2) concentration of 62 %. • Novel gasifier and burner structures for fine ash gasification are given. • Fine ash is quickly mixed at the outlet of burner and fully mixed in the center of gasifier. • The highest carbon conversion rate of fine ash entrained-flow gasifier is about 80 %. • Gasification agent channel diameter affects the mixing and gasification characteristics. • The outlet temperature exceeds 1600 °C which satisfies the requirement for liquid slag discharge. [ABSTRACT FROM AUTHOR]

Through a gas-particle cold-modeling experiment, the particle dynamic analyzer (PDA) is used to investigate the effects of fuel-lean coal/airflow angle and ratio of oil secondary air to F-layer secondary air on the gas/particle flows characteristics in the furnace of a Foster Wheeler (FW) down-fired boiler with enhanced stable combustion technology. As the fuel-lean coal/airflow angle increases from 10° to 45°, the peak value of the vertical dimensionless velocity of the gas/particle flows gradually increases, and the peak position gradually moves to the near wall region. As the ratio of oil secondary air to F-layer secondary air (the secondary air ratio for short) increased, the peak value of the vertical dimensionless velocity of the gas/particle flows gradually increased and the peak value position of the dimensionless velocity gradually moved towards the near-wall region. In actual operation, for the perspective of performance and safety, the recommended fuel-lean coal/airflow angle and secondary air ratio is 30°and 1:2 respectively. The enhanced stable combustion technology had been applied to two 600 MW FW down-fired boilers, and these boilers can achieve stable operation when burning a wide range of coal quality under the load section from 200 MW to 600 MW. • A Foster Wheeler down-fired boiler retrofitted with novel low-load stable combustion technology is studied by PDA. • Effects of fuel-lean coal/airflow angle and secondary air ratio on the gas/particle flows characteristics were investigated. • The fuel-lean coal/airflow angle of 30° and the secondary air ratio of 1:2 is recommended. • This novel low-load stable down-fired boiler combustion technology is suitable for a wide range of coal quality combustion. [ABSTRACT FROM AUTHOR]